Red mangroves emit hydrocarbons

The objective of this study is to investigate hydrocarbon species and amounts released by red mangrove foliage and determine if these quantities warrant future research on atmospheric chemical processing of these compounds. The field investigation took place during July 2001 at Key Largo, Florida Bay, Florida. Foliage still attached to plants was enclosed in cuvettes while air of known flow rates circulated around leaves to study, hydrocarbon emissions. Cuvette air samples underwent gas chromatographic analyses to determine species and amounts of hydrocarbons released by mangrove foliage. Red mangrove foliage emits isoprene and trace amounts of the monoterpenes of alpha-pinene, beta-pinene, camphene, and d-limonene. The mangrove flowers released these latter compounds in amounts ranging from 0.5 to 10 mg (monoterpene) per gram of dry biomass per hour. These fluxes are normalized to, the foliage temperature of 30 degreesC. When normalized to the foliage temperature of 30 degreesC and light levels of 1000 mumol m(-2) s(-1), isoprene emission rates as high as 0.092 +/- 0.109 mug (isoprene) per gram of dry biomass per hour were measured. Compared to terrestrial forest ecosystems, red mangroves are low isoprene emitters. During peak flowering periods in the summertime, however, red mangroves may emit sufficient amounts of monoterpenes to alter ground-level ozone concentrations and contribute to biogenic aerosol formation.

Occurrence and distribution of novel botryococcene hydrocarbons in freshwater wetlands of the Florida Everglades

A high abundance of isoprenoid hydrocarbons, the botryococcenes, with carbon numbers from 32 to 34 were detected in the Florida Everglades freshwater wetlands. These compounds were present in varying amounts up to 106 μg/gdw in periphyton, 278 μg/gdw in floc, and 46 μg/gdw in soils. Their structures were determined based on comparison to standards, interpretation of their mass spectra and those of their hydrogenation products, and comparison of Kovats indexes to those reported in the literature. A total of 26 cyclic and acyclic botryococcenes with 8 skeletons were identified, including those with fewer degrees of unsaturation, which are proposed as early diagenetic derivatives from the natural products. This is the first report that botryococcenes occur in the Everglades freshwater wetlands. Their potential biogenetic sources from green algae and cyanobacteria were examined, but neither contained botryococcenes. Thus, the source implication of botryococcenes in this ecosystem needs further study.

Ab initio quantum chemical studies on neutral-radical reactions of ethynyl (C2H) and cyano (CN) with unsaturated hydrocarbons

An Ab Initio/RRKM study of the reaction mechanism and product branching ratios of neutral-radical ethynyl (C2H) and cyano (CN) radical species with unsaturated hydrocarbons is performed. The reactions studied apply to cold conditions such as planetary atmospheres including Titan, the Interstellar Medium (ISM), icy bodies and molecular clouds. The reactions of C2H and CN additions to gaseous unsaturated hydrocarbons are an active area of study. NASA's Cassini/Huygens mission found a high concentration of C2H and CN from photolysis of ethyne (C2H2) and hydrogen cyanide (HCN), respectively, in the organic haze layers of the atmosphere of Titan. The reactions involved in the atmospheric chemistry of Titan lead to a vast array of larger, more complex intermediates and products and may also serve as a chemical model of Earth's primordial atmospheric conditions. The C2H and CN additions are rapid and exothermic, and often occur barrierlessly to various carbon sites of unsaturated hydrocarbons. The reaction mechanism is proposed on the basis of the resulting potential energy surface (PES) that includes all the possible intermediates and transition states that can occur, and all the products that lie on the surface. The B3LYP/6-311g(d,p) level of theory is employed to determine optimized electronic structures, moments of inertia, vibrational frequencies, and zero-point energy. They are followed by single point higher-level CCSD(T)/cc-vtz calculations, including extrapolations to complete basis sets (CBS) of the reactants and products. A microcanonical RRKM study predicts single-collision (zero-pressure limit) rate constants of all reaction paths on the potential energy surface, which is then used to compute the branching ratios of the products that result. These theoretical calculations are conducted either jointly or in parallel to experimental work to elucidate the chemical composition of Titan's atmosphere, the ISM, and cold celestial bodies.<.

Formation of Polycyclic Aromatic Hydrocarbons and Nitrogen Containing Polycyclic Aromatic Compounds in Titan's Atmosphere, the Interstellar Medium and Combustion

Several different mechanisms leading to the formation of (substituted) naphthalene and azanaphthalenes were examined using theoretical quantum chemical calculations. As a result, a series of novel synthetic routes to Polycyclic Aromatic Hydrocarbons (PAHs) and Nitrogen Containing Polycyclic Aromatic Compounds (N-PACs) have been proposed. On Earth, these aromatic compounds originate from incomplete combustion and are released into our environment, where they are known to be major pollutants, often with carcinogenic properties. In the atmosphere of a Saturn's moon Titan, these PAH and N-PACs are believed to play a critical role in organic haze formation, as well as acting as chemical precursors to biologically relevant molecules. The theoretical calculations were performed by employing the ab initio G3(MP2,CC)/B3LYP/6-311G** method to effectively probe the Potential Energy Surfaces (PES) relevant to the PAH and N-PAC formation. Following the construction of the PES, Rice-Ramsperger-Kassel-Markus (RRKM) theory was used to evaluate all unimolecular rate constants as a function of collision energy under single-collision conditions. Branching ratios were then evaluated by solving phenomenological rate expressions for the various product concentrations. The most viable pathways to PAH and N-PAC formation were found to be those where the initial attack by the ethynyl (C2H) or cyano (CN) radical toward a unsaturated hydrocarbon molecule led to the formation of an intermediate which could not effectively lose a hydrogen atom. It is not until ring cyclization has occurred, that hydrogen elimination leads to a closed shell product. By quenching the possibility of the initial hydrogen atom elimination, one of the most competitive processes preventing the PAH or N-PAC formation was avoided, and the PAH or N-PAC formation was allowed to proceed. It is concluded that these considerations should be taken into account when attempting to explore any other potential routes towards aromatic compounds in cold environments, such as on Titan or in the interstellar medium.

Aplicação do Na2S2O8, H2O2 e ferro na remediação de solos (latossolo e areia destrófica) contaminados com diesel

Environmental liabilities from accidents in the retail petroleum industry, especially in urban areas, have represented a serious problem whose impact reaches the underground, people's health and even economic losses with the remediation process. In U.S.A. are estimated hundreds of billions of dollars invested in soil remediation processes. The results of the reports and investigative reports of liabilities in fuel stations distributed in the urban area of Natal-RN were used to estimate the local scenario of contamination. This database has been possible to determine the main contaminants (BTEX, PAHs, TOC), affected neighborhoods and types of potentially more impacted soils. Experiments were carried out in order to reverse contamination of this scenario, where the soil type was a factor in the planning, because it influences directly on the effectiveness of remediation techniques studied: Oxidation by hydrogen peroxide and oxidation by sodium persulphate. These oxidants are activated forming free radicals (HO•-, SO4 •-, HO2 • , O2 •-, S2O8 -2, etc) responsible for to mineralize the hydrocarbons and other organic compounds (releasing O2 e CO2). In the activation process, the ferrous ions (II) and ferric (III) were studied as well as hydrogen peroxide activation technique with sodium persulfate, the latter being presented the best efficiency among all the study, when activated with Fe+3. In addition to defining the most efficient technique, the aim of this study was to evaluate the influence of different soils among oxidative techniques, characterizing the effect of the concentration of these oxidants and also the concentration of the catalysts. Exists in most scenarios evaluated the presence of intrinsic total iron soil matrix. The so-called latosols present microaggregates reddish indicating the presence of these reactive species like iron and clayey aspect. The kinetic study was conducted by experimental design and monitoring of the percentage of total carbon (SSM-5000A) in the solid and liquid phases, knowing that 82.4% of the diesel molecule is carbon. Yet organic carbon and pH of liquid samples were analyzed for technical, characterizing the influence of soil type and its operating condition. The Fenton-like technique H2O2 e Fe+2 presented satisfactory oxidation, including sandy soil, but well below the best result. The sodium persulphate only activated with temperature, even in the most favorable soil, did not provide good efficiency. The best technique in the study had the concentration profile with 2,2x10- 1mol.L-1 of Na2S2O8 activated with 6,53x10-1mol.L-1 of H2O2 and 2,5x10-2 Fe3+mol.L-1 which reduced in less than a day 96 contamination in red soil, initially with 66,667 mg of diesel per kg of clean soil

Avaliação do potencial das fibras de Ceiba Pentandra (Kapok) e Calotropis Procera como adsorventes de petróleo

On the basis of human evolution and the population increase was necessary, the emergence of new sources of energy, the development of new products and technologies. One such product, object of the industry revolution and of great importance to the development of humanity is the oil, a substance composed primarily of hydrocarbons which give rise to several other products as fuels, lubricants, polymers, solvents, cooking gas, asphalt for roads, fertilizers, medicines, paints, among other. However, mishandling this product may cause leaks and spills that generate huge damages to the environment and the economy. Soon, with the purpose of contributing to decrease is problematic, in this master's work was carried out an intensive search of the possible potential of the fibers of Ceiba pentandra (L.) "Kapok" and Calotropis Procera as bioadsorbents of petroleum in water. The choice of these fibers is due to surface properties such as oleophylics and hydrophobic, their buoyancy and yet, being biodegradable natural polymers derived from the Brazilian Northeast. This research was used experimental planning with response surface methodology (RSM) with the software Design Expert. The results were statistically efficient, obtaining a R2= 0.9995 for Calotropis Procera and a R2= 0.9993 for Kapok. And that, both fibers showed adsorption efficiency, removing more than 80% petroleum in water static and dynamic state.

Estudo de métodos de tratamento de efluentes (troca iônica e eletroquímico) separados e sequenciais para eliminação de derivados de petróleo

The produce of waste and the amount of the water produced coming from activities of petroleum production and extraction has been a biggest challenge for oil companies with respect to environmental compliance due to toxicity. The discard or the reuse this effluent containing organic compounds as BTEX (benzene, toluene, ethylbenzene and xylene) can cause serious environmental and human health problems. Thus, the objective this paper was study the performance of two process (separately and sequential) in one synthetic effluent for the benzene, toluene and xylene removal (volatile hydrocarbons presents in the produced water) through of electrochemical treatment using Ti/Pt electrode and exchange resin ionic used in the adsorption process. The synthetic solution of BTX was prepared with concentration of 22,8 mg L-1, 9,7 mg L-1 e 9,0 mg L-1, respectively, in Na2SO4 0,1 mol L-1. The experiments was developed in batch with 0.3 L of solution at 25ºC. The electrochemical oxidation process was accomplished with a Ti/Pt electrode with different current density (J = 10, 20 e 30 mA.cm-2). In the adsorption process, we used an ionic exchange resin (Purolite MB 478), using different amounts of mass (2,5, 5 and 10 g). To verify the process of technics in the sequential treatment, was fixed the current density at 10 mA cm-2 and the resin weight was 2.5 g. Analysis of UV-VIS spectrophotometry, chemical oxygen demand (COD) and gas chromatography with selective photoionization detector (PID) and flame ionization (FID), confirmed the high efficiency in the removal of organic compounds after treatment. It was found that the electrochemical process (separate and sequential) is more efficient than absorption, reaching values of COD removal exceeding 70%, confirmed by the study of the cyclic voltammetry and polarization curves. While the adsorption (separately), the COD removal did not exceed 25,8%, due to interactions resin. However, the sequential process (electrochemical oxidation and adsorption) proved to be a suitable alternative, efficient and cost-effectiveness for the treatment of effluents petrochemical.

A regulação da exploração e produção de hidrocarbonetos não convencionais no Brasil

The global energy crisis triggered the possibility of unconventional hydrocarbons exploration and production, culminating in the US energy revolution as well as making other countries interested in the development of these natural resources. The justification for this research comes from Brazil's interest in the use of hydraulic fracturing techniques in unconventional resources since the Brazilian National Agency of Petroleum, Natural Gas and Biofuels (ANP) organized the 12th acquisition process and published the Resolution no. 21 of April 10, 2014. The conflict between economic viability and the social and environmental damage from exploration and production of unconventional hydrocarbons in Brazil resulted in the search for a legal solution that would consider the economic, social and environmental interests. The main purpose here is to analyze the regulation of unconventional oil exploration and production in Brazil in order to show lack of regulatory instruments so far. The specific objectives are to investigate how the lack of effective regulation may ultimately prevent the development itself, analyze the importance of systematization of a new regulatory tool for ensuring legal security and energy, identify the key negative environmental and social impacts, and suggest possibilities approaches within the new regulatory framework. The research methodology stands out the hypothetico-deductive model as approach, and the comparative model as procedural method. Moreover, the research techniques used here are performance of a theoretical and descriptive questioning over literature search, analysis of Brazilian standardization and case laws, and a brief comparative study, in order to provide suggested approaches for a new regulatory framework.

A regulação da exploração e produção de hidrocarbonetos não convencionais no Brasil

The global energy crisis triggered the possibility of unconventional hydrocarbons exploration and production, culminating in the US energy revolution as well as making other countries interested in the development of these natural resources. The justification for this research comes from Brazil's interest in the use of hydraulic fracturing techniques in unconventional resources since the Brazilian National Agency of Petroleum, Natural Gas and Biofuels (ANP) organized the 12th acquisition process and published the Resolution no. 21 of April 10, 2014. The conflict between economic viability and the social and environmental damage from exploration and production of unconventional hydrocarbons in Brazil resulted in the search for a legal solution that would consider the economic, social and environmental interests. The main purpose here is to analyze the regulation of unconventional oil exploration and production in Brazil in order to show lack of regulatory instruments so far. The specific objectives are to investigate how the lack of effective regulation may ultimately prevent the development itself, analyze the importance of systematization of a new regulatory tool for ensuring legal security and energy, identify the key negative environmental and social impacts, and suggest possibilities approaches within the new regulatory framework. The research methodology stands out the hypothetico-deductive model as approach, and the comparative model as procedural method. Moreover, the research techniques used here are performance of a theoretical and descriptive questioning over literature search, analysis of Brazilian standardization and case laws, and a brief comparative study, in order to provide suggested approaches for a new regulatory framework.

Análise da biorremediação de compostos monoaromáticos em água através da pseudomonas aeruginosa

The monoaromatic compounds are toxic substances present in petroleum derivades and used broadly in the chemical and petrochemical industries. Those compounds are continuously released into the environment, contaminating the soil and water sources, leading to the possible unfeasibility of those hydrous resources due to their highly carcinogenic and mutagenic potentiality, since even in low concentrations, the BTEX may cause serious health issues. Therefore, it is extremely important to develop and search for new methodologies that assist and enable the treatment of BTEX-contaminated matrix. The bioremediation consists on the utilization of microbial groups capable of degrading hydrocarbons, promoting mineralization, or in other words, the permanent destruction of residues, eliminating the risks of future contaminations. This work investigated the biodegradation kinetics of water-soluble monoaromatic compounds (benzene, toluene and ethylbenzene), based on the evaluation of its consummation by the Pseudomonas aeruginosa bacteria, for concentrations varying from 40 to 200 mg/L. To do so, the performances of Monod kinetic model for microbial growth were evaluated and the material balance equations for a batch operation were discretized and numerically solved by the fourth order Runge-Kutta method. The kinetic parameters obtained using the method of least squares as statistical criteria were coherent when compared to those obtained from the literature. They also showed that, the microorganism has greater affinity for ethylbenzene. That way, it was possible to observe that Monod model can predict the experimental data for the individual biodegradation of the BTEX substrates and it can be applied to the optimization of the biodegradation processes of toxic compounds for different types of bioreactors and for different operational conditions.

Análise da biorremediação de compostos monoaromáticos em água através da pseudomonas aeruginosa

The monoaromatic compounds are toxic substances present in petroleum derivades and used broadly in the chemical and petrochemical industries. Those compounds are continuously released into the environment, contaminating the soil and water sources, leading to the possible unfeasibility of those hydrous resources due to their highly carcinogenic and mutagenic potentiality, since even in low concentrations, the BTEX may cause serious health issues. Therefore, it is extremely important to develop and search for new methodologies that assist and enable the treatment of BTEX-contaminated matrix. The bioremediation consists on the utilization of microbial groups capable of degrading hydrocarbons, promoting mineralization, or in other words, the permanent destruction of residues, eliminating the risks of future contaminations. This work investigated the biodegradation kinetics of water-soluble monoaromatic compounds (benzene, toluene and ethylbenzene), based on the evaluation of its consummation by the Pseudomonas aeruginosa bacteria, for concentrations varying from 40 to 200 mg/L. To do so, the performances of Monod kinetic model for microbial growth were evaluated and the material balance equations for a batch operation were discretized and numerically solved by the fourth order Runge-Kutta method. The kinetic parameters obtained using the method of least squares as statistical criteria were coherent when compared to those obtained from the literature. They also showed that, the microorganism has greater affinity for ethylbenzene. That way, it was possible to observe that Monod model can predict the experimental data for the individual biodegradation of the BTEX substrates and it can be applied to the optimization of the biodegradation processes of toxic compounds for different types of bioreactors and for different operational conditions.

A study of methods used to analyze total oil and polycyclic aromatic hydrocarbons in produced water: steps towards the validation of molecularly imprinted polymers for use in marine environmetns

Produced water is a by-product of offshore oil and gas production, and is released in large volumes when platforms are actively processing crude oil. Some pollutants are not typically removed by conventional oil/water separation methods and are discharged with produced water. Oil and grease can be found dispersed in produced water in the form of tiny droplets, and polycyclic aromatic hydrocarbons (PAHs) are commonly found dissolved in produced water. Both can have acute and chronic toxic effects in marine environments even at low exposure levels. The analysis of the dissolved and dispersed phases are a priority, but effort is required to meet the necessary detection limits. There are several methods for the analysis of produced water for dispersed oil and dissolved PAHs, all of which have advantages and disadvantages. In this work, EPA Method 1664 and APHA Method 5520 C for the determination of oil and grease will be examined and compared. For the detection of PAHs, EPA Method 525 and PAH MIPs will be compared, and results evaluated. APHA Method 5520 C Partition-Infrared Method is a liquid-liquid extraction procedure with IR determination of oil and grease. For analysis on spiked samples of artificial seawater, extraction efficiency ranged from 85 – 97%. Linearity was achieved in the range of 5 – 500 mg/L. This is a single-wavelength method and is unsuitable for quantification of aromatics and other compounds that lack sp³-hybridized carbon atoms. EPA Method 1664 is the liquid-liquid extraction of oil and grease from water samples followed by gravimetric determination. When distilled water spiked with reference oil was extracted by this procedure, extraction efficiency ranged from 28.4 – 86.2%, and %RSD ranged from 7.68 – 38.0%. EPA Method 525 uses solid phase extraction with analysis by GC-MS, and was performed on distilled water and water from St. John’s Harbour, all spiked with naphthalene, fluorene, phenanthrene, and pyrene. The limits of detection in harbour water were 0.144, 3.82, 0.119, and 0.153 g/L respectively. Linearity was obtained in the range of 0.5-10 g/L, and %RSD ranged from 0.36% (fluorene) to 46% (pyrene). Molecularly imprinted polymers (MIPs) are sorbent materials made selective by polymerizing functional monomers and crosslinkers in the presence of a template molecule, usually the analytes of interest or related compounds. They can adsorb and concentrate PAHs from aqueous environments and are combined with methods of analysis including GC-MS, LC-UV-Vis, and desorption electrospray ionization (DESI)- MS. This work examines MIP-based methods as well as those methods previously mentioned which are currently used by the oil and gas industry and government environmental agencies. MIPs are shown to give results consistent with other methods, and are a low-cost alternative improving ease, throughput, and sensitivity. PAH MIPs were used to determine naphthalene spiked into ASTM artificial seawater, as well as produced water from an offshore oil and gas operation. Linearity was achieved in the range studied (0.5 – 5 mg/L) for both matrices, with R² = 0.936 for seawater and R² = 0.819 for produced water. The %RSD for seawater ranged from 6.58 – 50.5% and for produced water, from 8.19 – 79.6%.

Petroleum taxation contingent on counter-factual investment behaviour

ACKNOWLEDGMENTS We thank the referees for constructive suggestions. Thanks are due to Norwegian Research Council (Petrosam 2) for financial support.

Regional Magma Plumbing and emplacement mechanisms of the Faroe-Shetland Sill Complex : Implications for magma transport and petroleum systems within sedimentary basins

Peer reviewed

Petroleum taxation contingent on counter-factual investment behaviour

ACKNOWLEDGMENTS We thank the referees for constructive suggestions. Thanks are due to Norwegian Research Council (Petrosam 2) for financial support.