Estudo de falhas por fadiga em caldeiras

In recent years, increasing demand for energy has led to studies to increase the amount of electricity produced. Due to this fact, more and more boilers are becoming important sources of electricity generation. To raise the efficiency of energy generated in the boilers is necessary to raise the steam pressure and temperature to values previously unimaginable. The use of more resistant materials and maintenance practices and most appropriate operation made it possible. The objective of this study is to test the main types of failure in a chemical recovery boiler, in particular due to fatigue in the superheater, because it is a component subjected to high temperatures and thus more subject to different failures. In this manner this study aims to reduce the incidence of unscheduled maintenance shutdowns, increasing the operation time under appropriate conditions. Modeling performed in this study, the failure did not occur, because we considered only the mechanical stress. Under normal conditions, mechanical stress in combination with thermal stresses can cause cracks in the tubes due to cyclical stresses, leading to fatigue failure

Estudo das interações entre proteína NS1 do hRSV e flavonóides utilizando métodos biofísicos

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

A tecnologia de microarray no estudo do câncer de cabeça e pescoço

(Microarray technology in study of head neck cancer). The microarray technology is a tool for global analysis of gene expression that allows investigating hundreds or thousands of genes in a sample using a hybridization reaction. This technology is based on hybridization between labeled targets derived from biological samples and an array of many DNA probes immobilized on a solid matrix, representing the genes of interest. The simultaneous study of hundreds of genes became the microarray technique a very important tool of global analysis, with applications in several areas, including the study of the development of cancer. Head and neck squamous cell carcinoma (HNSCC) is the fifth most common cancer worldwide, with a global annual incidence of 780,000 new cases. Large-scale studies involving microarrays have identified specific gene expression signatures associated with expression changes in HNSCC samples compared to normal tissue, as well as genes involved in clinical outcome and metastasis. However, the considerable heterogeneity among these studies occurs due to experimental design, number of samples, disease sites and stage, choice of microarray platform and results validation. Thus, there is much to be validated, before the technique has clinical utility. In relation to head and neck neoplasia, the large-scale gene analysis is very important, since the clinical and histopathological methods currently used appear to be insufficient to predict clinical progression and response to treatment. Thus, this approach could result in more effective diagnostic and prognostic and most appropriate therapy for this neoplasia.

Estudo e aplicação de diferentes métodos de resolução para problemas dinâmicos não-lineares em presença de atrito

The friction phenomena is present in mechanical systems with two surfaces that are in contact, which can cause serious damage to structures. Your understanding in many dynamic problems became the target of research due to its nonlinear behavior. It is necessary to know and thoroughly study each existing friction model found in the literature and nonlinear methods to define what will be the most appropriate to the problem in question. One of the most famous friction model is the Coulomb Friction, which is considered in the studied problems in the French research center Laboratoire de Mécanique des Structures et des Systèmes Couplés (LMSSC), where this search began. Regarding the resolution methods, the Harmonic Balance Method is generally used. To expand the knowledge about the friction models and the nonlinear methods, a study was carried out to identify and study potential methodologies that can be applied in the existing research lines in LMSSC and then obtain better final results. The identified friction models are divided into static and dynamic. Static models can be Classical Models, Karnopp Model and Armstrong Model. The dynamic models are Dahl Model, Bliman and Sorine Model and LuGre Model. Concerning about nonlinear methods, we study the Temporal Methods and Approximate Methods. The friction models analyzed with the help of Matlab software are verified from studies in the literature demonstrating the effectiveness of the developed programming

Estudo do efeito do processo de shot peening na taxa de propagação de trinca por fadiga na liga aeronáutica 2024 - T3

Pós-graduação em Engenharia Mecânica - FEG

Estudo do comportamento em fadiga das ligas AA6005, AA6063 e AA6351

Aluminum alloys have shown great potential for the automotive industry, especially aluminum alloys 6xxx series. This category has good mechanical strength and excellent corrosion resistance, important for the areas of construction and transport. The automotive industry has always shown great interest in the study of fatigue behavior, because structural components are subjected to cyclic and vibration loads, generating cracks and fracturing. The mechanical response depends on the material properties, applications, surface condition and microstructure. In this work was study the fatigue behavior of high cycle of machined bodies (not polished) and the effect of roughness on the fatigue life for three aluminum alloys of 6xxx series: AA6005, AA6351 and AA606, all in the T6 condition . S / N curves were made from fatigue tests in rotating bending (R = -1). The influence of roughness was studied by measuring the roughness of each specimen. Was compare the fatigue behavior of polished specimen and not polished specimens. The fractured surfaces of samples were observed by MEV, and it was observed that most of nucleation sites for fatigue crack is initiated below the surface

Métodos preventivos em primeiro molar permanente de crianças com experiência de cárie dentária: estudo clínico comparativo

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Efeito de métodos de desgaste com pontas diamantadas e da ressinterização sobre o limite de fadiga flexural de uma zircônia parcialmente estabilizada por ítria

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Cães American Pit Bull Terrier submetidos a exercício: respostas fisiológicas e estudo comparativo de métodos para quantificação de lactato

Pós-graduação em Medicina Veterinária - FCAV

Estudo experimental do uso de rebolos convencionais na usinagem do aço VP-50 utilizado na retificação cilíndrica, por meio de diferentes métodos de lubri-refrigeração

Pós-graduação em Engenharia Mecânica - FEB

Estudo de materiais supercondutores em forma de SQUID com uma constrição usando métodos de paralelização computacional

Pós-graduação em Ciência e Tecnologia de Materiais - FC

Análise do comportamento da cor de restaurações cerâmicas sem metal avaliadas por diferentes métodos: estudo clínico prospectivo

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Estudo comparativo do desempenho de diferentes membranas oclusivas de Látex Natural no reparo ósseo

Introduction: In dentistry, alveolar bone resorption is a limiting factor in the well being of individuals directly interfering in the stomatognathic system, causing problems in the context of overall health. Aiming to promote biological methods that can stimulate bone regeneration, several biomimetic strategies have been developed by the use of diverse materials possible to the bone matrix, culminating in the development of techniques that promote such repair. Objective: This work is a comparative study of the performance of films made with latex as occlusive membrane for Guided Bone Regeneration (GBR) procedure in three preparations: Latex preserved in ammonia, produced by Latex rubber clones IAN873 and PR255 polymerized immediately after collection and without use ammonia as a preservative. Methods: Sixty Wistar rats were randomly divided into 4 groups of 15 animals in which bone defects of critical size (8mm diameter) were made surgically in the skull. Group A was treated by GBR through the membrane latex preserved with ammonia, Group B received the membrane made of latex from IAN873, Group C, the membrane clone PR255 and group D was not treated by GBR. After a period of 7, 15 and 50 days, 5 animals from each group were euthanized, and specimens containing bone defect collected for microscopic examination (descriptive histology and histomorphometry). Results: The results showed that after 50 days there was bone formation in higher proportions in group D (p <0.05, ANOVA followed by Tukey), suggesting that further experiments should be conducted to conclude about the presence of ammonia and the influence of kind of rubber. Conclusion: GOR is a procedure proven effective in the treatment of bone defects. Therefore, further experiments should be conducted to reach a conclusion regarding the presence of ammonia in the latex composition for the manufacture of membranes, as well as the difference induced by the species of rubber.

Estudo químico e avaliação da atividade antimicrobiana de fungos endofíticos associados à Paepalanthus chiquitensis (eriocaulaceae) e efeitos de moduladores químicos epigenéticos no cultivo de Pochonia chlamydosporia

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)