Optimal scheduling of a renewable micro-grid in an isolated load area using mixed-integer linear programming

In the energy management of the isolated operation of small power system, the economic scheduling of the generation units is a crucial problem. Applying right timing can maximize the performance of the supply. The optimal operation of a wind turbine, a solar unit, a fuel cell and a storage battery is searched by a mixed-integer linear programming implemented in General Algebraic Modeling Systems (GAMS). A Virtual Power Producer (VPP) can optimal operate the generation units, assured the good functioning of equipment, including the maintenance, operation cost and the generation measurement and control. A central control at system allows a VPP to manage the optimal generation and their load control. The application of methodology to a real case study in Budapest Tech, demonstrates the effectiveness of this method to solve the optimal isolated dispatch of the DC micro-grid renewable energy park. The problem has been converged in 0.09 s and 30 iterations.

Internacionalização de pequenas e médias empresas em Portugal: abordagem programada vs abordagem não programada

Orientado por Mestre Anabela Ribeiro e Prof. Doutora Clara Ribeiro

Embedded platform for ECG biometric recognition

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia de Electrónica e Telecomunicações

Self-mated tribological systems based on multilayer micro/nanocrystalline CVD diamond coatings

The tribological response of multilayer micro/nanocrystalline diamond coatings grown by the hot filament CVD technique is investigated. These multigrade systems were tailored to comprise a starting microcrystalline diamond (MCD) layer with high adhesion to a silicon nitride (Si3N4) ceramic substrate, and a top nanocrystalline diamond (NCD) layer with reduced surface roughness. Tribological tests were carried out with a reciprocating sliding configuration without lubrication. Such composite coatings exhibit a superior critical load before delamination (130–200 N), when compared to the mono- (60–100 N) and bilayer coatings (110 N), considering ∼10 µm thick films. Regarding the friction behaviour, a short-lived initial high friction coefficient was followed by low friction regimes (friction coefficients between 0.02 and 0.09) as a result of the polished surfaces tailored by the tribological solicitation. Very mild to mild wear regimes (wear coefficient values between 4.1×10−8 and 7.7×10−7 mm3 N−1 m−1) governed the wear performance of the self-mated multilayer coatings when subjected to high-load short-term tests (60–200 N; 2 h; 86 m) and medium-load endurance tests (60 N; 16 h; 691 m).

Role of abrasive material on micro-abrasion wear tests

Micro-abrasion wear tests with ball-cratering configuration are widely used. Sources of variability are already studied by different authors and conditions for testing are parameterized by BS EN 1071-6: 2007 standard which refers silicon carbide as abrasive. However, the use of other abrasives is possible and allowed. In this work, ball-cratering wear tests were performed using four different abrasive particles of three dissimilar materials: diamond, alumina and silicon carbide. Tests were carried out under the same conditions on a steel plate provided with TiB2 hard coating. For each abrasive, five different test durations were used allowing understanding the initial wear phenomena. Composition and shape of abrasive particles were investigated by SEM and EDS. Scar areas were observed by optical and electronic microscopy in order to understand the wear effects caused by each of them. Scar geometry and grooves were analyzed and compared. Wear coefficient was calculated for each situation. It was observed that diamond particles produce well-defined and circular wear scars. Different silicon carbide particles presented dissimilar results as consequence of distinct particle shape and size distribution.

Um retrato do Empreendedorismo em Malanje-Angola: análise de negócios criados entre 2008-2012

Dissertação de Mestrado em Empreendedorismo e Internacionalização apresentada ao Instituto de Contabilidade e Administração do Porto para a obtenção do grau de Mestre em Empreendedorismo e Internacionalização, sob orientação de Professora Doutora Celsa Maria Carvalho Machado e Mestre Maria Luísa Verdelho Alves

Influence of the abrasive particles size in the micro-abrasion wear tests of TiAlSiN thin coatings

Ball rotating micro-abrasion tribometers are commonly used to carry out wear tests on thin hard coatings. In these tests, different kinds of abrasives were used, as alumina (Al2O3), silicon carbide (SiC) or diamond. In each kind of abrasive, several particle sizes can be used. Some studies were developed in order to evaluate the influence of the abrasive particle shape in the micro-abrasion process. Nevertheless, the particle size was not well correlated with the material removed amount and wear mechanisms. In this work, slurry of SiC abrasive in distilled water was used, with three different particles size. Initial surface topography was accessed by atomic force microscopy (AFM). Coating hardness measurements were performed with a micro-hardness tester. In order to evaluate the wear behaviour, a TiAlSiN thin hard film was used. The micro-abrasion tests were carried out with some different durations. The abrasive effect of the SiC particles was observed by scanning electron microscopy (SEM) both in the films (hard material) as in the substrate (soft material), after coating perforation. Wear grooves and removed material rate were compared and discussed.

Micro-abrasion wear behaviour of TiAlCrSiN nanostructured coatings

The injection process of glass fibres reinforced plastics promotes the moulds surface degradation by erosion. In order to improve its wear resistance, several kinds of PVD thin hard coatings were used. It is well-known that nanostructures present a better compromise between hardness and toughness. Indeed, when the coating is constituted by a large number of ultra-thin different layers, cracks and interface troubles tend to decrease. However, it is not clear that these nanostructures present a better wear behaviour in erosion processes. In order to study its wear behaviour, a sputtered PVD nanostructured TiAlCrSiN coating was used. The substrate and film surfaces topography were analyzed by profilometry and atomic force microscopy techniques. Film adhesion to the substrate was evaluated by scratch tests. The surface hardness was measured with a Vickers micro-hardness tester. The wear resistance was evaluated by micro-abrasion with a rotating ball tribometer tests. Slurry of SiC particles in distilled water was used in order to provoke the surface abrasion. Different duration tests were performed in order to analyze the wear evolution. After these tests, the wear mechanisms developed were analyzed by scanning electron microscopy. Wear craters were measured and the wear rate was calculated and discussed. With the same purpose, coated inserts were mounted in an injection mould working with a 30% glass fibres reinforced polypropylene. After 45 000 cycles no relevant wear was registered.

Business micro-location: factors, preferences and indicators to assess the influence factors

The paper presents a study on business micro-location behaviour as well as corresponding factors of influence, conducted in two metropolitan areas, Bucharest-Ilfov (Romania) and Greater Porto (Portugal). By business micro-location we refer to a specific site such as a building or facility, accommodating a business within a small, compact geographical area (e.g. metropolitan area). At this geographical scale, the macroeconomic layer factors were excluded, applicable when discern between regions or countries. The factors derived from location theory and previous empirical studies were surveyed, completing a cross-sectional analysis in order to find out the specific weights of the location factors and preferences, by region and by industry. Based on already established firms’ feedback on location, the specific weights were granted by each industry to the main location factors, types of areas, and types of accommodation facilities. The authors also suggested a model to integrate these results into a Geographical Information System (GIS).

A construção da comunidade lusófona apartir do antigo centro. Micro-comunidades e práticas da lusofonia

Dissertação apresentada para cumprimento dos requisitos necessários à obtenção do grau de Doutor em Sociologia.

O papel do inapem no fomento do empreendedorismo na provincia do Kwanza Norte-Angola

Dissertação de Mestrado apresentada ao Instituto de Contabilidade e Administração do Porto para a obtenção do grau de Mestre em Empreendedorismo e Internacionalização, sob orientação de Celsa Maria Carvalho Machado e Adalmiro Álvaro Malheiro de Castro Andrade Pereira

Consultoria e formação em marketing digital para PME’s

Trabalho de Projeto apresentado ao Instituto de Contabilidade e Administração do Porto para a obtenção do grau de Mestre em Marketing Digital, sob orientação de Doutor Freitas Santos

Intelligent Micro Grid Management using a Multi-Agent approach

Recent changes in electricity markets (EMs) have been potentiating the globalization of distributed generation. With distributed generation the number of players acting in the EMs and connected to the main grid has grown, increasing the market complexity. Multi-agent simulation arises as an interesting way of analysing players’ behaviour and interactions, namely coalitions of players, as well as their effects on the market. MASCEM was developed to allow studying the market operation of several different players and MASGriP is being developed to allow the simulation of the micro and smart grid concepts in very different scenarios This paper presents a methodology based on artificial intelligence techniques (AI) for the management of a micro grid. The use of fuzzy logic is proposed for the analysis of the agent consumption elasticity, while a case based reasoning, used to predict agents’ reaction to price changes, is an interesting tool for the micro grid operator.

Desenvolvimento e aluguer de software de faturação

As aplicações de Gestão ou Faturação são uma presença indispensável hoje em dia. Tendo o seu início nas aplicações “MS-DOS” em modo de texto, estas aplicações acompanharam a evolução dos sistemas operativos adotando um ambiente gráfico de forma natural. Se há poucos anos apenas as empresas com volumes de negócio significativo possuíam software de faturação, este foi sendo adotado por cada vez mais empresas e pequenos negócios. As alterações legislativas introduzidas desde 2011 conduziram a uma adoção generalizada por parte de pequenas e microempresas. O mercado de aplicações de gestão está saturado pelos grandes produtores de software nacionais: Primavera, Sage, etc. Estas aplicações, tendo sido construídas para PMEs (Pequenas e Médias Empresas) e mesmo grandes empresas, são excessivamente complexas e onerosas para muito pequenas e microempresas. O Modelo de negócio destes produtores de software é primordialmente a venda de Licenças e contratos de Manutenção, nalguns casos através de redes de Agentes. Este projeto teve como objetivo o desenvolvimento de uma Aplicação de Faturação, de baixo custo, simples e cross-platform para ser comercializada em regime de aluguer em Pequenas e Micro Empresas.

Práticas de gestão de recursos humanos em pequenas e médias empresas

O presente estudo tem como principal objectivo caracterizar as práticas de Gestão de Recursos Humanos mais desenvolvidas em pequenas e médias empresas (PME’s) portuguesas. Para melhor contextualizar a realidade objecto de estudo, tomou-se como ponto de partida a abordagem teórica sobre as diferentes fases evolutivas do conceito e conteúdo da GRH e, consequentemente, a sua caracterização no nosso país. Adicionalmente, é analisado o papel que o departamento de recursos humanos assume no desenvolvimento da GRH no interior das PME’s através da disseminação que faz das suas diferentes práticas, previamente identificadas a partir da revisão de literatura analisada. Foi identificado um conjunto de 21 práticas de GRH como as mais comummente desenvolvidas em contexto organizacional. Conclui-se que as PME’s apresentam pouca intensidade no desenvolvimento de práticas de GRH, ao mesmo tempo que se apresentam como limitadoras do grau de intervenção do departamento de RH, no desenvolvimento dessas práticas.