999 resultados para Medida de exposição à radiação
Resumo:
O presente trabalho tem como objectivo principal a realização de um estudo do efeito do ganho das antenas nas perdas de percurso de uma ligação na banda de frequência ISM (Insdustrial Scientific and Medical) nos 2,4 GHz. Para tal, foram utilizadas 14 antenas de 7 tipos diferentes (2 monopolo, 2 colineares, 2 grelhas, 2 Yagi, 2 painéis, 2 parabólicas e 2 helicoidais) com ganhos a variar desde os 1,3 a 23 dBi. Inicialmente, obtiveram-se os parâmetros fundamentais das antenas utilizadas, nomeadamente o diagrama de radiação e o ganho. Desenvolveu-se um sistema, que permite a medição do diagrama de radiação de forma automática através de um motor passo a passo. Uma aplicação desenvolvida em ambiente Matlab realiza o controlo do motor e desenha o respectivo diagrama em tempo real. Para a realização das medições da propagação do sinal desenvolveu-se um sistema que interliga a antena receptora a um computador portátil através de um analisador de espectros. À medida que as medições são efectuadas, a atenuação do sinal em função da distância é determinada e apresentada graficamente no computador sendo, ainda, representada a atenuação esperada no espaço livre. Para isto, implementou-se uma aplicação em ambiente Matlab que faz o tratamento e representação dos dados. Tendo-se conhecimento dos parâmetros das antenas, e com o sistema de medição implementado, passou-se às medições da propagação do sinal em diferentes meios, tais como, meio sem obstáculos, meio urbano, meio florestal caracterizado por troncos no percurso de propagação e meio florestal caracterizado por folhagem no percurso de propagação. Em cada meio foram efectuadas medições para 37 combinações de antenas, com ganhos conjuntos a variar desde os 2,6 até o 46 dBi. As medições foram efectuadas com a colocação da antena emissora numa posição fixa e com o afastamento da antena receptora em intervalos de 5 metros, até os 150 metros, seguindo a linha de máxima radiação entre ambas as antenas. Ainda, para os meios sem obstáculos e florestais, foram efectuadas medições para dois ângulos em relação à linha indicada, sendo estes de 30° e 330°, respectivamente. Com base nos resultados obtidos, verificou-se um aumento da atenuação à medida que se passou para meios mais obstruídos, sendo que, para o meio sem obstáculos a atenuação aproxima-se da curva do espaço livre. No meio urbano observou-se que a atenuação aumentou ligeiramente. No entanto, esta não é muito significativa quando comparada com a atenuação no espaço livre. Por último, notou-se um grande aumento da atenuação nos meios florestais, ao nível dos troncos e da vegetação, sendo superior para esta última. Relativamente às antenas, verificou-se que existe um aumento da atenuação na medida que o ganho destas aumenta, sendo mais visível para meios com maior obstrução (florestais). Para a situação em que as antenas encontram-se com desvios de 30° e 330°, verificou-se que este aumento é mais significativo para as antenas directivas (ganhos superiores).
Resumo:
As energias renováveis têm sido cada vez mais a alternativa encontrada para substituir o uso dos combustíveis fósseis na produção de energia. Neste contexto, surge a oportunidade de realizar um estudo sobre o “Potencial Solar dos Edifícios Públicos da RAM” como objeto de trabalho desta tese de Mestrado em Engenharia de Telecomunicações e Redes de Energia (METRE). Pretende-se que este estudo sirva para impulsionar o investimento nesta área por parte dos decisores regionais, dotando-os de um estudo do potencial de produção de energia solar nos edifícios públicos da RAM. Através de estudos desenvolvidos pelo LREC, ERAMAC - Maximização da Penetração das Energias Renováveis e Utilização Racional da Energia nas Ilhas da Macaronésia, e do Joint Research Centre (JRC), contendo dados do Instituto Meteorológico (IM), da Agência Regional da Energia e Ambiente da Região Autónoma da Madeira (AREAM), do LREC e do World Meteorological Organization (WMO), avaliou-se a radiação solar na RAM, através de tabelas e mapas de radiação solar, contendo a radiação solar global diária média mensal e média anual. Posteriormente fez-se uma análise da oferta do mercado atual de painéis fotovoltaicos (PV) em termos de eficiência, distinguindo as várias gerações de tipos de painéis introduzidos no mercado. Foram realizadas várias pesquisas em diversas áreas de energias renováveis e tecnologias existentes para, posteriormente, se realizar uma seleção e introspeção da informação essencial ao tema de forma a definir-se a fase de desenvolvimento desta tese. Com o auxílio da ferramenta computacional Quantum GIS, foram identificados alguns edifícios públicos com a dimensão e exposição solar apropriada para a colocação de sistemas solares nos mesmos. De seguida, foi realizado uma análise do preço pago/recebido por kWh consumido/produzido e cinco casos de estudos, nos quais foram focados os diferentes impactos de várias tecnologias solares nos prédios públicos da RAM, avaliando financeiramente os custos e retorno do investimento na aplicação destas tecnologias em cada caso, através das ferramentas computacionais, SolTerm e RETScreen. Finalmente retirou-se as respetivas conclusões acerca das opções tomadas, por exemplo, na escolha das tecnologias solares a implementar, os seus custos, o retorno do investimento, preços dos painéis fotovoltaicos, entre outros.
Resumo:
A elaboração deste relatório tem como principal objetivo a exposição das vivências, por nós experienciadas no âmbito do estágio pedagógico na vertente de ensino da Educação Física, realizado na escola secundária Jaime Moniz, no ano letivo 20142015. Relataremos todas as atividades realizadas no âmbito do estágio pedagógico, bem como os problemas encontrados e as estratégias por nós adotadas para a sua resolução. À medida que procedemos à descrição dos diferentes capítulos realizaremos as posteriores reflexões, repensando metodologias, propondo novas soluções e expondo as ilações retiradas a partir da observação do contexto. Em suma, apesar do caráter formal deste documento, pretendemos através do mesmo, retratar a singularidade do nosso percurso enquanto estagiária. Deste modo, este trabalho compila os conhecimentos adquiridos ao longo da formação académica, os conceitos e noções bibliográficos numa perspetiva pessoal devidamente fundamentada.
Resumo:
Leptospirosis is a worldwide zoonosis of considerable medical and economical importance that affects humans in both urban and rural contexts, as well as domestic animals and wild fauna. Leptospira interrogans is the causative agent and is transmitted to humans by indirect contact with contaminated soil or water. The clinical syndromes include sub clinical infection, self-limited anicteric febrile illness, and severe and potentially fatal illness, known as Weil´s syndrome. In developed countries, leptospirosis is related to occupational or recreational activities while in developing countries, outbreaks occur during floods. In those regions, traditional strategies to prevent the transmission are difficulties to be implemented because of costs and lack of community acceptance. In addition, no efficient vaccine is available for human use. Several studies have suggested that chemoprophylaxis with doxycycline pre and post-exposure may be effective to prevent leptospirosis. Leptospirosis has been reported in rural areas of the State of Rio Grande do Norte, Brazil since 1985 in rice farmers who present the anicteric illness. The disease cause great social and economics impact. The study was conducted in São Miguel where an epidemic of leptospirosis in rice farmers was reported. The main objective was to determine the efficacy of doxycycline in preventing Leptospira exposure. A taxa de soroprevalência de leptospirose na população estudada antes e após a colheita foi de 14,2% (n=22) e de 16.6% (n=27) respectivamente. Anti-Leptospira serology was determined for 61 subjects in two instances, pre and post-exposure to potential contaminated water. There was an increased risk of 29.0 per cent in acquiring infection for individuals that did not use doxycycline. In addition, an increased risk of 30.0 % observed in farmers who did not use protection when exposed to Leptospira. The adhesion to preventive chemoprophylaxis was 55.7%. Therefore doxycycline, under specific circunstances appears to be an effective alternative to protect against leptosprirosis infection. A large sample composed of individuals to adhere to preventive therapy is needed to define time, dosage and length of use of doxycycline in this area
Desenvolvimento de bloco de vedação com barita na composição de partida para blindagem de radiação X
Resumo:
This work main objective is to study the use of bricks in barium X-rays rooms in order to contribute to the optimization of shielding rooms diagnosis. The work was based on experimental measurements of X-ray attenuation (40 to 150 kV), using ceramic seal bearing the incorporation of barium sulfat (BaSO4). Different formulations were studied in three different firing temperatures and evaluated for incorporation in the ceramic body. The composition of 20% of barite processed at a temperature of 950 ° C showed better physical and mechanical properties, is considered the most suitable for the purpose of this work. Were produced bricks sealing composition formulated based on that presented the best technological features. These blocks were tested physically as a building material and wall protective barrier. Properties such as visual, deviation from the square, face flatness, water absorption and compressive strength were evaluated for all the blocks produced. The behavior of this material as attenuator for X-rays was investigated by experimental results which take into account mortar manufacturers barium through the different strains and compared with the reference material (Pb). The simulation results indicated that the ceramic block barium shows excellent properties of attenuation equivalence lead taking into account the energy used in diagnostic X-ray
Resumo:
In recent decades have seen a sharp growth in the study area of nanoscience and nanotechnology and is included in this area, the study of nanocomposites with self-cleaning properties. Since titanium dioxide (TiO2) has high photocatalytic activity and also antimicrobial, self-cleaning surfaces in your application has been explored. In this study a comparison was made between two synthesis routes to obtain TiO2 nanoparticles by hydrothermal method assisted by microwave. And after analysis of XRD and SEM was considered the best material for use in nanocomposites. It was deposited nanocomposite film of poly (dimethyl siloxane) (PDMS) with 0.5, 1, 1.5 and 2% by weight of nanoparticles of titanium dioxide (TiO2) by the spraying method. The nanocomposite was diluted with hexane and the suspension was deposited onto glass substrate, followed by curing in an oven with forced air circulation. The photocatalytic activity of the nanocomposite impregnated with methylene blue was evaluated by UV- vis spectroscopy from the intensity variation of absorption main peak at 660nm with time of exposure to the UV chamber. Changes in the contact angle and microhardness were analyzed before and after UV aging test. The effect of ultraviolet radiation on the chemical structure of the PDMS matrix was evaluated by spectrophotometry Fourier transform infrared (FTIR).The results indicated that the addition of TiO2 nanoparticles in the coating PDMS gave high photocatalytic activity in the decomposition of methylene blue, an important characteristic for the development of self-cleaning coatings
Resumo:
The use of infrared burners in industrial applications has many advantages in terms of technical-operational, for example, uniformity in the heat supply in the form of radiation and convection, with greater control of emissions due to the passage of exhaust gases through a macro-porous ceramic bed. This paper presents an infrared burner commercial, which was adapted an experimental ejector, capable of promoting a mixture of liquefied petroleum gas (LPG) and glycerin. By varying the percentage of dual-fuel, it was evaluated the performance of the infrared burner by performing an energy balance and atmospheric emissions. It was introduced a temperature controller with thermocouple modulating two-stage (low heat / high heat), using solenoid valves for each fuel. The infrared burner has been tested and tests by varying the amount of glycerin inserted by a gravity feed system. The method of thermodynamic analysis to estimate the load was used an aluminum plate located at the exit of combustion gases and the distribution of temperatures measured by a data acquisition system which recorded real-time measurements of the thermocouples attached. The burner had a stable combustion at levels of 15, 20 and 25% of adding glycerin in mass ratio of LPG gas, increasing the supply of heat to the plate. According to data obtained showed that there was an improvement in the efficiency of the 1st Law of infrared burner with increasing addition of glycerin. The emission levels of greenhouse gases produced by combustion (CO, NOx, SO2 and HC) met the environmental limits set by resolution No. 382/2006 of CONAMA
Resumo:
Biomass is considered the largest renewable energy source that can be used in an environmentally sustainable. From the pyrolysis of biomass is possible to obtain products with higher energy density and better use properties. The liquid resultant of this process is traditionally called bio-oil. The use of infrared burners in industrial applications has many advantages in terms of technical-operational, for example, uniformity in the heat supply in the form of radiation and convection, with a greater control of emissions due to the passage of exhaust gases through a macroporous ceramic bed. This paper presents a commercial infrared burner adapted with an ejector proposed able to burn a hybrid configuration of liquefied petroleum gas (LPG) and bio-oil diluted. The dilution of bio-oil with absolute ethanol aimed to decrease the viscosity of the fluid, and improving the stability and atomization. It was introduced a temperature controller with thermocouple modulating two stages (low heat / high heat), and solenoid valves for fuels supply. The infrared burner has been tested, being the diluted bio-oil atomized, and evaluated its performance by conducting energy balance. The method of thermodynamic analysis to estimate the load was used an aluminum plate located at the exit of combustion gases and the distribution of temperatures measured by thermocouples. The dilution reduced the viscosity of the bio-oil in 75.4% and increased by 11% the lower heating value (LHV) of the same, providing a stable combustion to the burner through the atomizing with compressed air and burns combined with LPG. Injecting the hybrid fuel there was increase in the heat transfer from the plate to the environment in 21.6% and gain useful benefit of 26.7%, due to the improved in the efficiency of the 1st Law of Thermodynamics of infrared burner
Resumo:
The increase in ultraviolet radiation (UV) at surface, the high incidence of non-melanoma skin cancer (NMSC) in coast of Northeast of Brazil (NEB) and reduction of total ozone were the motivation for the present study. The overall objective was to identify and understand the variability of UV or Index Ultraviolet Radiation (UV Index) in the capitals of the east coast of the NEB and adjust stochastic models to time series of UV index aiming make predictions (interpolations) and forecasts / projections (extrapolations) followed by trend analysis. The methodology consisted of applying multivariate analysis (principal component analysis and cluster analysis), Predictive Mean Matching method for filling gaps in the data, autoregressive distributed lag (ADL) and Mann-Kendal. The modeling via the ADL consisted of parameter estimation, diagnostics, residuals analysis and evaluation of the quality of the predictions and forecasts via mean squared error and Pearson correlation coefficient. The research results indicated that the annual variability of UV in the capital of Rio Grande do Norte (Natal) has a feature in the months of September and October that consisting of a stabilization / reduction of UV index because of the greater annual concentration total ozone. The increased amount of aerosol during this period contributes in lesser intensity for this event. The increased amount of aerosol during this period contributes in lesser intensity for this event. The application of cluster analysis on the east coast of the NEB showed that this event also occurs in the capitals of Paraiba (João Pessoa) and Pernambuco (Recife). Extreme events of UV in NEB were analyzed from the city of Natal and were associated with absence of cloud cover and levels below the annual average of total ozone and did not occurring in the entire region because of the uneven spatial distribution of these variables. The ADL (4, 1) model, adjusted with data of the UV index and total ozone to period 2001-2012 made a the projection / extrapolation for the next 30 years (2013-2043) indicating in end of that period an increase to the UV index of one unit (approximately), case total ozone maintain the downward trend observed in study period
Resumo:
The measurement of patient satisfaction can provide information about the success of the care provider in reaching the values and meeting the expectations of the patient. The purpose of this study was to translate into the Portuguese language and to culturally customize to the Brazilian population the instrument to measure patient satisfaction with physical therapy elaborated by Goldstein et al. The study sample was made up of 279 patients who were undergoing physical therapy treatment at 39 different private clinics in a middle-sized town in northeastern Brazil. For the translation of the survey instrument, the back-translation technique was employed, in association with the bilingual method. The reliability and validity of the Brazilian version of the instrument were both assessed. Reliability analysis, carried out with the computation of Cronbach alpha coefficients, showed that the measures obtained with the instrument have a high degree of internal consistency. The aspects dealing with the patient therapist relationship are the most important predictors of satisfaction, followed by those dealing with courtesy, privacy, and practical aspects such as efficiency of the facility in the patient admissions process, setting up of appointments, and waiting time in waiting room. Items dealing with aspects such as location of the facility and availability of parking facilities may underestimate the reliability of the instrument. This study translated, culturally customized, and validated an instrument to measure patient satisfaction with physical therapy originally developed in English. By so doing, this study has made this instrument available to the Brazilian society, and it has rendered it a useful parameter that can be utilized in our country in the field of physical therapy
Resumo:
Conselho Nacional de Desenvolvimento Científico e Tecnológico
Resumo:
A análise foliar de nitrogênio, comumente empregada em laboratórios de rotina, é destrutiva e nem sempre rápida, obstante para a tomada de decisão. Objetivou-se com a pesquisa estudar as medidas SPAD, em mudas de goiabeira (Psidium guajava L.) cultivada em solução nutritiva completa, observando-se as diferenças entre cultivares, épocas de amostragem e tipos de folhas avaliadas. O delineamento foi inteiramente casualizado, com quatro repetições, em parcelas sub-subdivididas. Assim, foi utilizada como parcela as duas cultivares de goiabeira (Paluma e Século XXI), como subparcelas os tipos de folhas (+1, +2 e +3) e, cinco épocas de amostragem ao longo do período experimental (60, 75, 90, 105 e 120 dias, após o transplantio de mudas) Concluiu-se que a leitura SPAD em mudas de goiabeira é influenciada pela cultivar, tipo de folha e época de amostragem. O terceiro par de folhas mostrou-se mais adequado para avaliar o estado nutricional do nitrogênio nas mudas de goiabeira a partir da leitura SPAD. As cultivares de goiabeira apresentaram diferença na leitura SPAD apenas aos 60 e 90 dias após o transplantio, independentemente do tipo de folha.
Resumo:
A transmissão de radiação ultravioleta de comprimentos de onda entre 250 e 360 nm através do pelame e da epiderme de bovinos foi determinada em laboratório, usando-se amostras de couro de animais recém-abatidos. A quantidade de radiação transmitida através do pelame depende da coloração e também das características estruturais do pelame (espessura da capa; comprimento, diâmetro, número e inclinação dos pêlos), pelas quais é definido o trajeto médio de um fóton pela massa de pêlos (L). A maior transmissão é proporcionada por pelames brancos com altos valores de L, ao passo que pelames negros em geral apresentam transmissão nula ou muito baixa. Quanto menos pigmentada a epiderme, maior a transmissão de radiação através da sua superfície. A melhor proteção é proporcionada por pelames negros com baixo valor de L sobre epiderme igualmente negra, mas em vista do aquecimento causado pela absorção de radiação térmica (em vacas Holandesas a temperatura das malhas negras atinge 44,1ºC ao mesmo tempo em que a das malhas brancas é 37,7ºC), a combinação ideal para ambientes tropicais é um pelame branco com baixo valor de L sobre epiderme negra, uma combinação dificilmente encontrada em animais de raças européias. Uma alternativa seria um pelame negro com um baixo valor de L. Animais vermelhos apresentam alta transmissão de radiação UV através da epiderme e do pelame, sendo desaconselhados para ambientes tropicais. Entretanto, foi observada uma vaca Holandesa com áreas isoladas de epiderme negra coberta com pelame branco, o que pode trazer perspectivas para uma seleção para combinações mais adequadas de epiderme e pelame em bovinos de raças européias.
Resumo:
It is a fact that the fundamental rights of citizens are being recognized and guaranteed by the state over time, regardless of the belief that if these rights has always been part of the heritage of subjective individuals, or whether they will be aggregated during the course of human history. In that, emerged the rights of freedom of men and, subsequently, the rights to create a situation of equality between the humans, the so-called social rights. In turn, as these rights known as social, to be implemented, need a positive action by the state, more precisely by the state power whose function is to manage public money and create policies for implementation of fundamental rights. Given this, pay attention to the right to health, was created the Programa de Medicamentos de Dispensação Excepcional, which aims to provide high-cost medicines to citizens Brazilian carriers of serious diseases, such as Alzheimer's and Mal Hepatitis C. Also on the program, it provides a way which will be mandatory that the drugs will be offered in such situations, and does not include a means of updating the list predicted able to monitor the progress of medicine that have been in the interest of the program. Given that, at present it is necessary to mention the recognition of another fundamental right: the right to development, which is the right of access to positive actions being implemented by the State, which are nothing more than public policy, gender which the Programa de Medicamentos de Dispensação Excepcional is kind. Thus, through the search in legislation and doctrine in relation to the theme, this work has the aim to examine the extent of the state to provide exceptional dispensing of medicines. Specifically, if the State in attention to the right to development and the implementation of the right to health, can really list exhaustively the drugs to be provided by the State, and what are the elements guiding this choice and how to control the same