A learning environment for robotic production line simulation

This paper presents a framework for a robotic production line simulation learning environment using Autonomous Ground Vehicles (AGV). An eLearning platform is used as interface with the simulator. The objective is to introduce students to the production robotics area using a familiar tool, an eLearning platform, and a framework that simulates a production line using AGVs. This framework allows students to learn about robotics but also about several areas of industrial management engineering without requiring an extensive prior knowledge on the robotics area. The robotic production line simulation learning environment simulates a production environment using AGVs to transport materials to and from the production line. The simulator allows students to validate the AGV dynamics and provides information about the whole materials supplying system which includes: supply times, route optimization and inventory management. The students are required to address several topics such as: sensors, actuators, controllers and an high level management and optimization software. This simulator was developed with a known open source tool from robotics community: Player/Stage. This tool was extended with several add-ons so that students can be able to interact with a complex simulation environment. These add-ons include an abstraction communication layer that performs events provided by the database server which is programmed by the students. An eLearning platform is used as interface between the students and the simulator. The students can visualize the effects of their instructions/programming in the simulator that they can access via the eLearning platform. The proposed framework aims to allow students from different backgrounds to fully experience robotics in practice by suppressing the huge gap between theory and practice that exists in robotics. Using an eLearning platform eliminates installation problems that can occur from different computers software distribution and makes the simulator accessible by all students at school and at home.

Autonomous guided vehicles applied to industrial engineering and management studies

This article presents a framework to an Industrial Engineering and Management Science course from School of Management and Industrial Studies using Autonomous Ground Vehicles (AGV) to supply materials to a production line as an experimental setup for the students to acquire knowledge in the production robotics area. The students must be capable to understand and put into good use several concepts that will be of utmost importance in their professional life such as critical decisions regarding the study, development and implementation of a production line. The main focus is a production line using AGVs, where the students are required to address several topics such as: sensors actuators, controllers and an high level management and optimization software. The presented framework brings to the robotics teaching community methodologies that allow students from different backgrounds, that normally don’t experiment with the robotics concepts in practice due to the big gap between theory and practice, to go straight to ”making” robotics. Our aim was to suppress the minimum start point level thus allowing any student to fully experience robotics with little background knowledge.

Environmental modeling with precision navigation using ROAZ autonomous surface vehicle

The use of robotic vehicles for environmental modeling is discussed. This paper presents diverse results in autonomous marine missions with the ROAZ autonomous surface vehicle. The vehicle can perform autonomous missions while gathering marine data with high inertial and positioning precision. The underwater world is an, economical and environmental, asset that need new tools to study and preserve it. ROAZ is used in marine environment missions since it can sense and monitor the surface and underwater scenarios. Is equipped with a diverse set of sensors, cameras and underwater sonars that generate 3D environmental models. It is used for study the marine life and possible underwater wrecks that can pollute or be a danger to marine navigation. The 3D model and integration of multibeam and sidescan sonars represent a challenge in nowadays. Adding that it is important that robots can explore an area and make decisions based on their surroundings and goals. Regard that, autonomous robotic systems can relieve human beings of repetitive and dangerous tasks.

Avaliação do impacte dos solários no desempenho energético de edifícios residenciais

Dissertação para obtenção do Grau de Mestre em Engenharia Civil

Field experiments for marine casualty detection with autonomous surface vehicles

In this paper we present a set of field tests for detection of human in the water with an unmanned surface vehicle using infrared and color cameras. These experiments aimed to contribute in the development of victim target tracking and obstacle avoidance for unmanned surface vehicles operating in marine search and rescue missions. This research is integrated in the work conducted in the European FP7 research project Icarus aiming to develop robotic tools for large scale rescue operations. The tests consisted in the use of the ROAZ unmanned surface vehicle equipped with a precision GPS system for localization and both visible spectrum and IR cameras to detect the target. In the experimental setup, the test human target was deployed in the water wearing a life vest and a diver suit (thus having lower temperature signature in the body except hands and head) and was equipped with a GPS logger. Multiple target approaches were performed in order to test the system with different sun incidence relative angles. The experimental setup, detection method and preliminary results from the field trials performed in the summer of 2013 in Sesimbra, Portugal and in La Spezia, Italy are also presented in this work.

Groundtruth system for underwater benchmarking

Oceans - San Diego, 2013

Combining sparse and dense methods in 6D Visual Odometry

13th International Conference on Autonomous Robot Systems (Robotica), 2013, Lisboa

6D Visual Odometry with Dense Probabilistic Egomotion Estimation

Proceedings of the International Conference on Computer Vision Theory and Applications, 361-365, 2013, Barcelona, Spain

Structured Light System Calibration for Perception in Underwater Tanks

The process of visually exploring underwater environments is still a complex problem. Underwater vision systems require complementary means of sensor information to help overcome water disturbances. This work proposes the development of calibration methods for a structured light based system consisting on a camera and a laser with a line beam. Two different calibration procedures that require only two images from different viewpoints were developed and tested in dry and underwater environments. Results obtained show, an accurate calibration for the camera/projector pair with errors close to 1 mm even in the presence of a small stereos baseline.

Structured Light System for Underwater Inspection Operations

In this work we propose the development of a stereo SLS system for underwater inspection operations. We demonstrate how to perform a SLS calibration both in dry and underwater environments using two different methods. The proposed methodology is able to achieve quite accurate results, lower than 1 mm in dry environments. We also display a 3D underwater scan of a known object size, a sea scallop, where the system is able to perform a scan with a global error lower than 2% of the object size.

Probabilistic Egomotion for Stereo Visual Odometry

We present a novel approach of Stereo Visual Odometry for vehicles equipped with calibrated stereo cameras. We combine a dense probabilistic 5D egomotion estimation method with a sparse keypoint based stereo approach to provide high quality estimates of vehicle’s angular and linear velocities. To validate our approach, we perform two sets of experiments with a well known benchmarking dataset. First, we assess the quality of the raw velocity estimates in comparison to classical pose estimation algorithms. Second, we added to our method’s instantaneous velocity estimates a Kalman Filter and compare its performance with a well known open source stereo Visual Odometry library. The presented results compare favorably with state-of-the-art approaches, mainly in the estimation of the angular velocities, where significant improvements are achieved.

Probabilistic Stereo Egomotion Transform

In this paper we propose a novel fully probabilistic solution to the stereo egomotion estimation problem. We extend the notion of probabilistic correspondence to the stereo case which allow us to compute the whole 6D motion information in a probabilistic way. We compare the developed approach against other known state-of-the-art methods for stereo egomotion estimation, and the obtained results compare favorably both for the linear and angular velocities estimation.

Os anúncios na imprensa periódica portuguesa – da grande depressão à II Guerra Mundial

Dissertação de Mestrado em História Contemporânea

Melhoria do Processo Produtivo da Pietec Através das Ferramentas Kaizen

Esta Tese de Mestrado foi realizada na empresa Pietec Cortiças S.A.. A empresa Pietec Cortiças S.A. é a unidade industrial responsável pela produção de rolhas técnicas de cortiça do Grupo Piedade. O objetivo desta tese prende-se com a melhoria do processo produtivo de uma das suas secções, a secção da Marcação. Esta secção é responsável pela marcação da superfície da rolha, pela aplicação do tratamento de superfície e pelo embalamento das rolhas. A otimização do processo da secção de Marcação, na qualidade de última secção do processo produtivo, permitirá à empresa obter vantagens competitivas. De forma a atingir o objetivo proposto, foi realizado um levantamento exaustivo do processo produtivo e das respetivas operações. Esta análise permitiu a identificação dos possíveis pontos de desperdício, a sua avaliação e a definição de possíveis melhorias que visam o aumento de produtividade e a redução do número de produtos não conformes. Uma vez identificados os pontos críticos do processo, procedeu-se à definição das ações de melhoria a implementar de forma a melhorar o processo produtivo. As ações tomadas assentam na filosofia Lean e nos seus princípios, utilizando-se algumas das ferramentas desta filosofia para concretizar os objetivos traçados. A ferramenta de análise Plan-Do-Check-Act (PDCA) foi a ferramenta base do projeto, acompanhando na elaboração do plano de ação, na implementação das ferramentas 5S e Single Minute Exchange of Die (SMED), na verificação dos resultados e no plano de manutenção das melhorias alcançadas. Após a implementação das medidas definidas no processo de marcação da superfície das rolhas, foi mensurada uma melhoria de 23 % no tempo médio de setup da máquina de marcação. Esta melhoria global foi alcançada através de intervenções no processo de vazamento do circuito da máquina de marcação, no procedimento de armazenamento dos moldes de marcação e na alteração dos mecanismos de ajuste da máquina de marcar e de orientar. No processo de embalamento das rolhas, as medidas implementadas produziram um aumento de 1,7 % no número de rolhas produzidas e uma redução do número de rolhas não conformes de 3,6 %. Os resultados obtidos no projeto demonstram que é possível continuar a melhorar o estado atual dos processos. Constatou-se ainda que, com a adoção de ferramentas de análise e de proposta de melhoria adequadas, é possível atuar sobre os processos e obter melhorias a curto prazo, sem que para isso seja necessário efetuar grandes investimentos.

Redução dos Temmpos de Paragem não Programada numa Linha de Maquinação

A Dissertação que se pretende desenvolver decorre em ambiente industrial numa empresa, em que as principais áreas de actuação dizem respeito à injecção e maquinação de alumínio. Os componentes aí injectados e maquinados, são componentes que servirão posteriormente a indústria automóvel num vasto leque de aplicações, desde componentes para sistemas hidráulicos de travagem e componentes para sistemas de lubrificação. Nesta dissertação foi abordada a temática da redução do tempo de paragem não planeada numa linha de maquinação, pelo que se elencaram as principais causas que originavam essas paragens. Recorrendo à metodologia SMED, e a um vasto conjunto de técnicas auxiliares de determinação de causas como os 5 WHY´s, diagrama de Ishikawa, 5S e Kaizen, foram propostas diversas melhorias para a optimização do procedimento de troca de modelo, incluindo um conjunto de regras que visam a sustentabilidade do processo a médio e longo prazo. Com as melhorias adoptadas, verificou-se uma redução de 27,9% no tempo total de troca de modelo comparativamente com o tempo registado antes da implementação da metodologia SMED. Destaca-se a redução de 75% no tempo de montagem e desmontagem dos dispositivos no 3ºProcesso da linha em estudo. Revelou-se também crucial que para a implementação da técnica SMED ser bem sucedida em termos de eficiência e sustentabilidade, devem ser adoptadas um conjunto de diversas ferramentas “Lean Management” e de normalização do trabalho.