Síntese, caracterização de ferritas espinélio com propriedades magnéticas e absorvedoras de microondas

Were synthesized spinel-type ferrites with general formula Ni0,8Mg0.2-xMxFe2O4, where M represents the doping Mn, Co or Mn + Co simultaneously, x ranges for the values 0.02, 0.05 and 0.1. The value of x was divided by 2 in cases where M equals Mn and Co conjugates. We used the citrate precursor method and heat treatment to obtain the phases at 1100°C. The materials were characterized by XRD, TGA/ DTGA, SEM, MAV and reflectivity measurements by the method of waveguide. Powders to 350°C/3.5 h were crystalline and nanosized. According to the results this temperature all powders have a percentage of ferrite phase over 90%. The composition had the addition of Mn and Co simultaneously showed a higher percentage of secondary phase NiO, 5.8%. The TGA/DTGA curves indicate that this sample reached phase (s) crystalline (s) at lowest temperatures. The X-ray diffractograms of the samples calcined at 350°C and 1100°C were treated with the Rietveld refinament technique. The powders calcined at 1100 °C/3h in air show to be 100% except spinel phase composition with 0.02 doping. The micrographs show clusters of particles with sizes smaller than 1 μm in calcination temperature of 1100°C which agreed with the result of Rietveld refinement. In the compositions doped with Mn were higher values of magnetization (45.90 and 53.20 Am2/kg), which did not cause high microwave absorption. The theoretical calculation of magnetization (MT) was consistent with the results, considering that there was agreement between the increase of magnetization experimental and theoretical. It was observed that there was the interrelation of the final effect of absorption with the thickness of MARE, the composition of ferrimagnetic materials and in particular the specific values of frequency. The analysis shows that the reflectivity increases in the concentration of cobalt increased the frequency range and also for absorption 10.17 GHz and 84%, respectively. The best result of chemical homogeneity and the value of 2.96 x 10-2 tesla coercive field were crucial for high performance ferrite absorber with 0.1 cobalt. The Cobalt has high magnetocrystalline anisotropy, it is associated with an increased coercive field, Hc. Therefore, this property improves the results of reflectivity of spinel ferrites

Síntese e caracterização de redes metalorgânicas baseadas em zinco e ácidos benzenodicarboxílicos

Metal Organic Frameworks (MOFs) are supramolecular structures consisted of ions or metal clusters coordinated to organic ligands which are repeated in two or three dimensions. These structures have atracted much attention due to their properties such as low density, high specific surface area and large volume of pores. In this work, MOFs consisted of zinc clusters connected by ditopic ligands, terephthalic acid (1,4- H2BDC) or isophthalic acid (1,3-H2BDC) were synthesized. To obtain the proposed materials, different routes and synthetic parameters were tested, such as the molar ratio of the precursors, the addition of template molecules, the type of solvente, the addition of organic base or the type of a counter-ion of Zn salt. It was found that the variation of these parameters led to the formation of different metalorganic structures. The solids obtained were characterized by XRD, SEM and IR. For the samples identified as MOF- 5, it was verified that the structure was composed of both interpenetrated and non interpenetrated structures. These samples showed a low stability, becoming totally transformed into another structure within less than 72 hours. The addition of the nickel and/or cobalt was found to be a promissing method for increasing the stability of MOF- 5, which in this case, still remained unconverted to another structure even after 15 days of exposure to air. The samples prepared from 1,3-H2BDC were probably new, still unknown Metal Organic Frameworks

Preparo e caracterização de membranas de quitosana modificadas com poli (ácido acrílico)

The aim of this study was to generate an asymmetric biocompactible and biodegradable chitosan membrane modified by the contact with a poly(acrylic acid) solution at one of its sides at room temperature and 60◦C. The pure chitosan membrane, as well as the ones treated with poly(acrylic acid) were characterized by infrared spectroscopy (FTIRATR) at angles of 39◦, 45◦ and 60◦ , swelling capacity in water, thermal analysis (TG/DTG), scanning electronic microscopy (SEM) and permeation experiments using metronidazole at 0,1% and 0,2% as a model drug. The results confirmed the presence of ionic interaction between chitosan and poly(acrylic acid) by means of a polyelectrolyte complex (PEC) formation. They also showed that such interactions were more effective at 60◦C since this temperature is above the chitosan glass transition temperature wich makes the diffusion of poly(acrylic acid) easier, and that the two treated membranes were asymmetrics, more thermically stable and less permeable in relation to metronidazole than the pure chitosan membrane

Síntese e caracterização da ferrita de MnZn obtida pelo método dos citratos precursores

It was synthesized MnZn ferrite with general formulae Mn1-xZnxFe2O4 (mol%), 0,3 ≤ x ≤ 0,7 by using the citrate precursor method. The precursors decomposition was studied by thermogravimetric analysis (TGA), differential thermogravimetric analysis (DTG), differential thermal analysis (DTA) and Fourier transform infrared (FTIR) of powder calcined at 350ºC/3,5h. X-ray diffraction pattern (XRD) of samples was done from 350 to 1200ºC/2h using various atmospheres. The power calcined at 350ºC/3,5h formed spinel phase. It is necessary atmosphere control to avoid secondary phase such as hematite. From 900 to 1200ºC was obtained 90,66 and 100% of MnZn spinel ferrite phase, respectively. Analysis by dispersive energy scanning (EDS) at 350ºC shows high Mn and Zn dispersion, indicating that the diffusion process was homogeneous. Semi-quantitative analysis by EDS verified that despite the atmosphere control during calcinations at high temperatures (< 800ºC) occurred ZnO evaporation causing stoichiometric deviation. Vibrating sample magnetometer (VSM) measures show soft ferrite material characteristics with Hc from 6,5 x 10-3 to 11,1 x 10-2 T. Saturation magnetization (Ms) and initial permeability (µi) of MnZn spinel phase obtained, respectively, from 14,3 to 83,8 Am2/kg and 14,1 to 62,7 (Am2/kg)T

Caracterização estrutural de Perovskitas Lax-1AxCoO3 (x=0 e 0,2) ,dopadas com cálcio e bario, por espectroscopia de absorção de raios X (XAS).

In this work, the structures of LaCoO3, La0,8Ba0,2CoO3 and La0,8Ca0,2CoO3 perovskites were characterized as a function of temperature (LaCoO3 structure being analyzed only at room temperature). The characterization of these materials were made by X-Ray Absorption Spectroscopy (XAS), in the cobalt K-edge, taking into account the correlated Einstein model X-ray absorption fine structure (EXAFS). The first part of the absorption spectrum corresponded the X-ray absorption near edge structure (XANES) and extended X-ray absorption fine structure (EXAFS). These materials were prepared by the combustion method. The combustion products were calcinated at 900 0C, for 6 hours in air. Noted that the sample LaCoO3 at room temperature and samples doped with Calcium and Barium in the temperature range of 50 K to 298 K showed greater distortion to monoclinic symmetry with space group I2/a. However, the sample doped with barium at the temperatures 50 K, 220 K, and 260 K showed a slight distortion to rhombohedral symmetry with space group R-3c. The La0,8Ca0, 2CoO3 structure was few sensitive to temperature variation, showing a higher local distortion in the octahedron and a higher local thermal disorder. These interpretations were in agreement with the information electronic structural on the XANES region and geometric in the EXAFS region

Síntese e caracterização de zeólita beta hierarquizada e materiais híbridos micro-mesoporosos aplicados no craqueamento de PEAD

A catalyst of great interest to the scientific community tries to unite the structure of ordered pore diameter from mesoporous materials with the properties of stability and acid activity to microporous zeolites. Thus a large number of materials was developed in the past decades, which although being reported as zeolites intrinsically they fail to comply with some relevant characteristics to zeolites, and recently were named zeolitic materials of high accessibility. Among the various synthesis strategies employed, the present research approaches the synthesis methods of crystallization of silanized protozeolitic units and the method of protozeolitic units molded around surfactant micelles, in order for get materials defined as hierarchical zeolites and micro-mesoporous hybrid materials, respectively. As goal BEA/MCM-41 hybrid catalysts with bimodal pore structure formed by nuclei of zeolite Beta and cationic surfactant cetyltrimethylammonium were developed. As also was successfully synthesized the hierarchical Beta zeolite having a secondary porosity, in addition to the typical and uniform zeolite micropores. Both catalysts were applied in reactions of catalytic cracking of high density polyethylene (HDPE), to evaluate its properties in catalytic activity, aiming at the recycling of waste plastics to obtain high value-added raw materials and fuels. The BEA/MCM-41 hybrid materials with 0 days of pre-crystallization did not show enough properties for use in catalytic cracking reactions, but they showed superior catalytic properties compared to those ordered mesoporous materials of Al-MCM-41 type. The structure of Beta zeolite with hierarchical porosity leads the accessibility of HDPE bulky molecules to active centers, due to high external area. And provides higher conversion to hydrocarbons in the gasoline range, especially olefins which have great interest in the petrochemical industry

Síntese, caracterização e estudo fotofísico de complexos de 4,4- diaminoestilbeno-2,2-dissulfonato com íons lantanídeos

This is a work involving fundamental studies of chemistry where the synthesis and structural characterization, as well as a possible future application of these new compounds as luminescent sensors or sunscreen agents, complexes with 4,4 diaminostilbene-2,2-disulfonic (DSD) and trivalent lanthanide ions La3+, Nd3+, Eu3+, Gd3+ and Yb3+, were synthesized in the ratio of 3 mmol: 1 mmol (DSD: lanthanides). The complexes obtained with these ions were present in powder form and were characterized by complexometric titration with EDTA CHN Elemental analysis, molecular absorption spectroscopy in the ultraviolet region, the absorption spectroscopy in the infrared, thermal analysis (TG / DTG), Nuclear Magnetic Resonance - NMR 1H and Luminescence Spectroscopy. The complexometric titration and CHN analysis, confirmed the TG / DTG which suggest that these complexes have the following general chemical formulas: [La2(C14H12S2O6N2)2(H2O)2Cl2].7H2O,[Nd2(C14H12S2O6N2)2(H2O)2Cl2].6H2O,[Eu2(C14 H12S2O6N2)2(H2O)2Cl2].7H2O,[Gd2(C14H12S2O6N2)2(H2O)2Cl2].4H2O e [Yb2(C14H12S2O6N2)2(H2O)2].6H2O. The disappearance of the bands in the infrared spectrum at 2921 cm-1 and 2623 cm-1 and the displacement of the bands in the spectra of the amine complex indicate that the lanthanide ion is coordinated to the oxygen atoms and the sulfonate groups of the nitrogens amines, suggesting the formation of the dimer. The disappearance of the signal and the displacement signal SO3H amines in the 1H NMR spectrum of this complex are also indicative coordination and dimer formation. The Thermogravimetry indicates that the DSD is thermally stable in the range of 40º to 385°C and their complexes with lanthanide ions exhibit weight loss between 4 and 5 stages. The Uv-visible spectra indicated that the DSD and complexes exhibit cis isomers. The analysis of luminescence indicates that the complexes do not exhibit emission in the region of the lanthanides but an intense emission part of the binder. This is related to the triplet states of the ligand, which are in the lowest energy state emitting lanthanide ions, and also the formation of the dimer that suppress the luminescence of ion Eu3+. The formation of dimer was also confirmed by calculating the europium complex structure using the model Hamiltonian PM6 and Sparkle

Caracterização química e toxicológica da água produzida descartada em plataformas de óleo e gás na costa brasileira e seu comportamento dispersivo no mar

The production of oil and gas is usually accompanied by the production of water, also known as produced water. Studies were conducted in platforms that discharge produced water in the Atlantic Ocean due to oil and gas production by Petrobras from 1996 to 2006 in the following basins: Santos (Brazilian south region), Campos (Brazilian southeast region) and Ceara (Brazilian northeast region). This study encompasses chemical composition, toxicological effects, discharge volumes, and produced water behavior after releasing in the ocean, including dispersion plumes modeling and monitoring data of the marine environment. The concentration medians for a sampling of 50 samples were: ammonia (70 mg L-1), boron (1.3 mg L1), iron (7.4 mg L-1), BTEX (4.6 mg L-1), PAH (0.53 mg L-1), TPH (28 mg L-1); phenols (1.3 mg L-1) and radioisotopes (0.15 Bq L-1 for 226Ra and 0.09 Bq L-1 for 228Ra). The concentrations of the organic and inorganic parameters observed for the Brazilian platforms were similar to the international reference data for the produced water in the North Sea and in other regions of the world. It was found significant differences in concentrations of the following parameters: BTEX (p<0.0001), phenols (p=0.0212), boron (p<0.0001), iron (p<0.0001) and toxicological response in sea urchin Lytechinus variegatus (p<0.0001) when considering two distinguished groups, platforms from southeast and northeast Region (PCR-1). Significant differences were not observed among the other parameters. In platforms with large gas production, the monoaromatic concentrations (BTEX from 15.8 to 21.6 mg L-1) and phenols (from 2 to 83 mg L-1) were higher than in oil plataforms (median concentrations of BTEX were 4.6 mg L-1 for n=53, and of phenols were 1.3 mg L-1 for n=46). It was also conducted a study about the influence of dispersion plumes of produced water in the vicinity of six platforms of oil and gas production (P-26, PPG-1, PCR-1, P-32, SS-06), and in a hypothetical critical scenario using the chemical characteristics of each effluent. Through this study, using CORMIX and CHEMMAP models for dispersion plumes simulation of the produced water discharges, it was possible to obtain the dilution dimension in the ocean after those discharges. The dispersion plumes of the produced water modelling in field vicinity showed dilutions of 700 to 900 times for the first 30-40 meters from the platform PCR-1 discharge point; 100 times for the platform P-32, with 30 meters of distance; 150 times for the platform P-26, with 40 meters of distance; 100 times for the platform PPG-1, with 130 meters of distance; 280 to 350 times for the platform SS-06, with 130 meters of distance, 100 times for the hypothetical critical scenario, with the 130 meters of distance. The dilutions continue in the far field, and with the results of the simulations, it was possible to verify that all the parameters presented concentrations bellow the maximum values established by Brazilian legislation for seawater (CONAMA 357/05 - Class 1), before the 500 meters distance of the discharge point. These results were in agreement with the field measurements. Although, in general results for the Brazilian produced water presented toxicological effects for marine organisms, it was verified that dilutions of 100 times were sufficient for not causing toxicological responses. Field monitoring data of the seawater around the Pargo, Pampo and PCR-1 platforms did not demonstrate toxicity in the seawater close to these platforms. The results of environmental monitoring in seawater and sediments proved that alterations were not detected for environmental quality in areas under direct influence of the oil production activities in the Campos and Ceara Basin, as according to results obtained in the dispersion plume modelling for the produced water discharge

Caracterização química e toxicológica da água produzida descartada em plataformas de óleo e gás na costa brasileira e seu comportamento dispersivo no mar

The production of oil and gas is usually accompanied by the production of water, also known as produced water. Studies were conducted in platforms that discharge produced water in the Atlantic Ocean due to oil and gas production by Petrobras from 1996 to 2006 in the following basins: Santos (Brazilian south region), Campos (Brazilian southeast region) and Ceara (Brazilian northeast region). This study encompasses chemical composition, toxicological effects, discharge volumes, and produced water behavior after releasing in the ocean, including dispersion plumes modeling and monitoring data of the marine environment. The concentration medians for a sampling of 50 samples were: ammonia (70 mg L-1), boron (1.3 mg L1), iron (7.4 mg L-1), BTEX (4.6 mg L-1), PAH (0.53 mg L-1), TPH (28 mg L-1); phenols (1.3 mg L-1) and radioisotopes (0.15 Bq L-1 for 226Ra and 0.09 Bq L-1 for 228Ra). The concentrations of the organic and inorganic parameters observed for the Brazilian platforms were similar to the international reference data for the produced water in the North Sea and in other regions of the world. It was found significant differences in concentrations of the following parameters: BTEX (p<0.0001), phenols (p=0.0212), boron (p<0.0001), iron (p<0.0001) and toxicological response in sea urchin Lytechinus variegatus (p<0.0001) when considering two distinguished groups, platforms from southeast and northeast Region (PCR-1). Significant differences were not observed among the other parameters. In platforms with large gas production, the monoaromatic concentrations (BTEX from 15.8 to 21.6 mg L-1) and phenols (from 2 to 83 mg L-1) were higher than in oil plataforms (median concentrations of BTEX were 4.6 mg L-1 for n=53, and of phenols were 1.3 mg L-1 for n=46). It was also conducted a study about the influence of dispersion plumes of produced water in the vicinity of six platforms of oil and gas production (P-26, PPG-1, PCR-1, P-32, SS-06), and in a hypothetical critical scenario using the chemical characteristics of each effluent. Through this study, using CORMIX and CHEMMAP models for dispersion plumes simulation of the produced water discharges, it was possible to obtain the dilution dimension in the ocean after those discharges. The dispersion plumes of the produced water modelling in field vicinity showed dilutions of 700 to 900 times for the first 30-40 meters from the platform PCR-1 discharge point; 100 times for the platform P-32, with 30 meters of distance; 150 times for the platform P-26, with 40 meters of distance; 100 times for the platform PPG-1, with 130 meters of distance; 280 to 350 times for the platform SS-06, with 130 meters of distance, 100 times for the hypothetical critical scenario, with the 130 meters of distance. The dilutions continue in the far field, and with the results of the simulations, it was possible to verify that all the parameters presented concentrations bellow the maximum values established by Brazilian legislation for seawater (CONAMA 357/05 - Class 1), before the 500 meters distance of the discharge point. These results were in agreement with the field measurements. Although, in general results for the Brazilian produced water presented toxicological effects for marine organisms, it was verified that dilutions of 100 times were sufficient for not causing toxicological responses. Field monitoring data of the seawater around the Pargo, Pampo and PCR-1 platforms did not demonstrate toxicity in the seawater close to these platforms. The results of environmental monitoring in seawater and sediments proved that alterations were not detected for environmental quality in areas under direct influence of the oil production activities in the Campos and Ceara Basin, as according to results obtained in the dispersion plume modelling for the produced water discharge

Caracterização física e sensorial do café produzido nas condições topoclimáticas de Jesuitas, Paraná

Climatic variations influence formation and maturation of coffee grains by altering their intrinsic characteristics, which call allow for several types of coffee qualities, including the potential for production of special coffee. This study was carried out to verify the effect of environmental conditions and crop cultivation on chemical composition and their consequences in cup quality of coffees from region of Jesuitas, Parana State. During the same crop season this study was accomplished (2002-2003), cup quality was evaluated among the producers in several coffee-growing municipalities in Parana State. It was observed that 86% of samples were classified simply as "soft" (smooth flavor) or "hard" (bolder flavor), and 14% were classified as rioysh/rio (strong unpleasant taste). The results concluded that the practices adopted by producers, who have collaborated with the study, reflected positively oil the final cup quality, when compared to the overall quality results in the State. The climatic conditions and practices of crop management and harvest ill the Jesuitas region made for bolder coffee with low acidity, comparable to high quality coffees produced in Brazil and abroad.

Caracterização social e tecnológica da produção de uvas para mesa em pequenas propriedades rurais da região de Jales-SP

A viticultura é uma atividade relevante para os produtores rurais do Estado de São Paulo, sobretudo aqueles detentores de pequenas áreas. O presente trabalho teve como objetivo caracterizar os principais aspectos sociais e tecnológicos utilizados na produção de uvas para mesa na região de Jales (SP). Os dados foram levantados nos anos de 2009 e 2010, a partir da aplicação de questionários a 19 produtores de uva e do acompanhamento do ciclo de produção de 10 propriedades. Os produtores cultivam pelo menos três cultivares diferentes de uva, sendo as principais: 'Niagara Rosada', 'Itália' e 'Benitaka'. A área média das propriedades é de, aproximadamente, 21 ha, e a área média com parreiras de uva é de 2,4 ha. A maioria dos produtores não conta com assistência técnica regular, não segue recomendações de adubação e não emprega critérios técnicos para o manejo da irrigação. O controle de doenças é realizado de forma preventiva e intensa, chegando a superar 100 aplicações por ciclo, no caso das uvas finas para mesa. Os resultados devem subsidiar a realização de outras pesquisas, assim como programas de planejamento e transferência de tecnologia, proporcionando ao produtor um manejo mais adequado da cultura, bem como o desenvolvimento sustentável rural regional.

Caracterização dos enunciados de um aluno não-falante usuário de recurso suplementar de comunicação durante a construção de histórias

A narrativa pode conectar elementos diversos e, assim, promover a construção de sentenças verticais e horizontais, frente à mediação de interlocutor. Esta pesquisa visou analisar a extensão e a organização sintática dos enunciados de narrativas construídas por um aluno não-falante usuário de recurso suplementar de comunicação. Previamente à construção das narrativas, selecionadas de acordo com os centros de interesse, idade, grau de escolaridade e temáticas trabalhadas na escola do aluno, símbolos gráficos do Picture Communication Symbols eram confeccionados e adaptados para que, por meio destes e dos recursos verbais e não-verbais inerentes à atividade discursiva, a história pudesse ser contada, por acesso visual e auditivo, pelo interlocutor e recontada pelo aluno, após a estruturação e organização dos múltiplos signos em sentenças. Todas as interações foram filmadas e complementadas com anotações de um diário de registro contínuo. Após a análise das transcrições das fitas e das anotações do diário, foi possível determinar três estágios de unidades significativas: 1) Caracterização ou natureza dos elementos constituintes dos enunciados das narrativas em: a) objeto; b) símbolo gráfico; c) escrita; d) vocalização; e) gesto representativo; 2) Extensão dos enunciados das narrativas de 1 a 6 elementos, linearmente, e 7 ou mais elementos; 3) Organização sintática dos elementos constituintes das narrativas em sujeito, verbo e objeto isolados, em sentenças verticais, e associados, em sentenças horizontais. Ressaltou-se, assim, a ampliação e aprimoramento da organização e da estrutura sintática dos enunciados das narrativas construídas pelo aluno mediado pelo interlocutor.

Caracterização genética e evolução dos vírus dengue no Estado do Rio Grande do Norte

Dengue is considered as the most important arthropod-borne viral disease throughout the world due to the high number of people at risk to be infected, mainly in tropical and subtropical regions of the planet. The etiologic agent is Dengue Virus (DENV), it is a single positive-stranded RNA virus of the family Flavivirus, genus Flaviviridae. Four serotypes are known, DENV-1, DENV-2, DENV-3 and DENV-4. One of the most important characteristic of these viruses is the genetic variability, which demands phylogenetic and evolutionary studies to understand key aspects like: epidemiology, virulence, migration patterns and antigenic characteristics. The objective of this study is the genetic characterization of dengue viruses circulating in the state of Rio Grande does Norte from January 2010 to December 2012. The complete E gene (1485 pb) of DENV1, 2 e 4 from Brazilian (Rio Grande do Norte) patients was sequenced. Phylogenetic analysis was performed using MEGA 5.2 software, Tamura-Nei model and Neighbor-Joining trees were inferred for the datasets. In Brazil, there is just one DENV-1 genotype (genotype V), one DENV-2 genotype (Asian/American) and two DENV-4 genotypes (genotypes I and II). Brazilian strains of DENV-1 are subdivided in two different lineages (BR-I and BR-II), the Brazilian strains of DENV-2 are subdivided in four lineages (BRI-IV) and genotype II of DENV-4 is subdivided in three Brazilian lineages (BRI-III). The viruses isolated in RN belong to lineage BR-II (DENV-1), BR-IV (DENV-2) and BR-III (DENV-4).The Caribbean and near Latin American countries are the main source of these viruses to Brazil. Amino acids substitutions were detected in three domains of E protein, this makes clear the necessity of studies that associate epidemiological and molecular data to better understand the effects of these mutations. This is the first study about genetic characterization and evolution of Dengue viruses in Rio Grande do Norte, Brazil

Caracterização de um modelo experimental de Diabetes Mellitus, induzido pela aloxana em ratos: estudo clínico e laboratorial

OBJETIVO: O presente estudo teve por objetivo caracterizar as alterações clínicas e laboratoriais do rato portador de Diabetes Mellitus induzido pela administração endovenosa de aloxana. MÉTODOS: Os animais foram distribuídos, por sorteio, em dois grupos experimentais: Grupo Controle Normal (G1), constituído de 25 animais sadios, e Grupo Diabético (G2), formado por 25 animais diabéticos graves, que foram avaliados em cinco momentos (1, 3, 6, 9 e 12 meses) de seguimento, tendo sido estudados os seguintes parâmetros: evolução clínica (peso, ingestão hídrica, ingestão alimentar e diurese) e exames bioquímicos (glicemia de jejum, glicose urinária, glicosúria, cetonúria, colesterol total, colesterol HDL, triglicérides e lipídios). RESULTADOS: A injeção de aloxana 2% na via endovenosa do rato acompanhou-se de um índice de mortalidade de 39%, tendo produzido diabetes grave também em 39% dos animais. O diabetes foi caracterizado por queda progressiva do peso corporal, elevação substancial da ingestão hídrica, ingestão alimentar e da diurese, com valores glicêmicos acima de 300 mg/dl, glicosúria 3+ e, eventualmente, cetonúria. O diabetes não altera o perfil de colesterol e lípides de ratos a longo prazo. CONCLUSÃO: Nossos estudos revelam que a aloxana produz, no rato, alterações clínicas e laboratoriais características de diabetes grave, as quais possibilitam estudos a longo prazo do diabetes.

Vegetação dunar: caracterização estrutural de dunas do município de Natal-RN como subsídio para implantação de técnicas de reflorestamernto, recuperação e conservação do ecossistema

The Brazilian coast has a wide variety of complex environments and ecosystems along the coast, about 80% are represented by sandbanks and dunes. The coastal ecosystems were the first to suffer the impacts man and places, as the very fragile ecosystems, are somehow altered. Are few areas of restinga well as natural features, very few protected in conservation units. Only in the last two decades the Brazilian restinga have been studies that are showing their importance for biodiversity of the country, though its economic importance remains largely unknown. In Rio Grande do Norte in the restinga vegetation and dune environments extend for almost the entire coast. The dunes are distinguished in the coastal landscape of the state due to the exuberance of its forms, heights and coating plants. The dune system is of fundamental importance for the maintenance of coastal urban settlements, especially for the city of Natal, acting on the hydrological dynamics of water table and reducing the effect of wind and movement of grains of sand to the interior and thus avoiding the burial City. However, the ecosystem of restinga and dune environments have been weakened and destroyed according to the intense urbanization and the knowledge of the vegetation of restinga installed on the dunes are still scarce. Thus, the objective of this study was to characterize the structure and floristic composition of vegetation established on a dune in the Dunes State Park Christmas and gather information to develop a model of recovery of the dune ecosystem. This dissertation is composed of 2 chapters, the first being: Structure of the vegetation of the dunes Dunes State Park in Natal, RN with the objective of describing the structure and composition of species of tree-shrub vegetation of restinga dunes of the Parque das Dunas and second: Recovery of degraded areas in a sand dune, which aimed to review the terms and concepts used in the theme of recovery and the techniques for recovery of degraded areas with emphasis on sandy environments and poor in nutrients, reporting some experiences within and external to Brazil the country, mainly in the Northeast and dunes positive and negative aspects that should be followed in building a model to be adopted for the recovery of local dunes