Fractional dynamics in the trajectory control of redundant manipulators

Under the pseudoinverse control, robots with kinematical redundancy exhibit an undesirable chaotic joint motion which leads to an erratic behavior. This paper studies the complexity of fractional dynamics of the chaotic response. Fourier and wavelet analysis provides a deeper insight, helpful to know better the lack of repeatability problem of redundant manipulators. This perspective for the study of the chaotic phenomena will permit the development of superior trajectory control algorithms.

Control of a 6-DOF parallel manipulator through a mechatronic approach

This paper shows that a hierarchical architecture, distributing several control actions in growing levels of complexity and using resources of reconfigurable computing, enables one to take into account the ease of future modifications, updates and improvements in robotic applications. An experimental example of a Stewart—Gough platform control (a platform applied as the solution to countless practical problems) is presented using reconfigurable computing. The software and hardware developed are structured in independent blocks. This open architecture implementation allows easy expansion of the system and better adaptation of the platform to its related tasks.

Optimal fuzzy PID control tuned with genetic algorithms

Fuzzy logic controllers (FLC) are intelligent systems, based on heuristic knowledge, that have been largely applied in numerous areas of everyday life. They can be used to describe a linear or nonlinear system and are suitable when a real system is not known or too difficult to find their model. FLC provide a formal methodology for representing, manipulating and implementing a human heuristic knowledge on how to control a system. These controllers can be seen as artificial decision makers that operate in a closed-loop system, in real time. The main aim of this work was to develop a single optimal fuzzy controller, easily adaptable to a wide range of systems – simple to complex, linear to nonlinear – and able to control all these systems. Due to their efficiency in searching and finding optimal solution for high complexity problems, GAs were used to perform the FLC tuning by finding the best parameters to obtain the best responses. The work was performed using the MATLAB/SIMULINK software. This is a very useful tool that provides an easy way to test and analyse the FLC, the PID and the GAs in the same environment. Therefore, it was proposed a Fuzzy PID controller (FL-PID) type namely, the Fuzzy PD+I. For that, the controller was compared with the classical PID controller tuned with, the heuristic Ziegler-Nichols tuning method, the optimal Zhuang-Atherton tuning method and the GA method itself. The IAE, ISE, ITAE and ITSE criteria, used as the GA fitness functions, were applied to compare the controllers performance used in this work. Overall, and for most systems, the FL-PID results tuned with GAs were very satisfactory. Moreover, in some cases the results were substantially better than for the other PID controllers. The best system responses were obtained with the IAE and ITAE criteria used to tune the FL-PID and PID controllers.

A pré-fabricação em betão em edifícios

No presente trabalho apresenta-se um levantamento com base na literatura especializada, das diversas soluções estruturais em betão pré-fabricado existentes, aplicadas em edifícios correntes, mais especificamente as soluções ao nível dos elementos que as constituem, nomeadamente no que respeita a ligações estruturais dos elementos, com combinações in situ, das estruturas préfabricadas e as moldadas em obra, aproveitando o que de melhor se pode obter de ambas as técnicas, com vista a obter um melhor resultado final. Apesar do setor da construção civil estar em crise, tal como vários outros setores, as empresas de pré-fabricação apresentam soluções que poderão contrariar esta tendência, nomeadamente através da diversificação e flexibilização da sua produção, com inovação, criatividade e elevada qualidade. Num mercado em que a construção de edifícios de raiz sofreu um grande abrandamento, começa a surgir no mercado a necessidade de se reabilitar as construções existentes, nomeadamente nos grandes centros das cidades que foram perdendo população ao longo dos tempos. Esta requalificação do espaço urbano permite o desenvolvimento de soluções estruturais pré-fabricadas, no que respeita à reabilitação dos elementos existentes, quer por justaposição para reforço das estruturas, quer por inserção de elementos novos para efetuar correções. Os baixos custos de mão de obra, equipamentos e estaleiro, assim como a redução dos prazos de construção e entrega ao cliente final, dado que a produção não está dependente das condições existentes in situ para se desenvolver, destacam-se da construção civil tradicional. A produção integral dos elementos pré-fabricados de betão em fábrica tem outras vantagens, entre as quais, um melhor planeamento e controle da segurança, um controle rigoroso de qualidade, a redução dos custos de reparação e manutenção, melhor sustentabilidade com redução da quantidade de resíduos produzidos.

Optimising the energy consumption on pultrusion process

This study is based on a previous experimental work in which embedded cylindrical heaters were applied to a pultrusion machine die, and resultant energetic performance compared with that achieved with the former heating system based on planar resistances. The previous work allowed to conclude that the use of embedded resistances enhances significantly the energetic performance of pultrusion process, leading to 57% decrease of energy consumption. However, the aforementioned study was developed with basis on an existing pultrusion die, which only allowed a single relative position for the heaters. In the present work, new relative positions for the heaters were investigated in order to optimise heat distribution process and energy consumption. Finite Elements Analysis was applied as an efficient tool to identify the best relative position of the heaters into the die, taking into account the usual parameters involved in the process and the control system already tested in the previous study. The analysis was firstly developed based on eight cylindrical heaters located in four different location plans. In a second phase, in order to refine the results, a new approach was adopted using sixteen heaters with the same total power. Final results allow to conclude that the correct positioning of the heaters can contribute to about 10% of energy consumption reduction, decreasing the production costs and leading to a better eco-efficiency of pultrusion process.

Application of a control banding tool for risk level assessment and control of nanoparticles exposure in welding operations

Scope of study: welding operations result in harmful emissions of nanoparticles; the aim of emissions monitorisation is to evaluate exposure levels and to derive protection measures in order to protect exposed workers; however, the traditional approach of comparing measured concentrations with exposure limits cannot be used; but risk levels can be quantified by using Control Banding Strategies.

Direct torque control em máquinas assíncronas

Dissertação apresentada na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para obtenção do grau de Mestre em Engenharia Electrotécnica e de Computadores

Hidatidosis humana: ecografía de campo para la determinación de grupos de alto riesgo en la evaluación de un programa de control

El desarrollo de equipos ultrasonográficos portátiles ha permitido incorporar esta técnica a los métodos de detección precoz de la Hidatidosis Humana. En esta experiência fueron efectuadas 690 ecografias, hallándose un 5.51% de imágenes compatibles en población general y un 12.24% en grupos de riesgo (convivientes de casos operados). Se observo una disminución significativa de los porcentajes de infección en el hombre en población general en Ias áreas bajo programa de control, utilizándose Ias encuestas ecográficas para esta determinación. Se concluyó sobre la posibilidad de incorporar la ecografía a los sistemas de vigilância epidemiológica de la hidatidosis humana.

Lean na gestão de fluxos logísticos da Dorel Portugal, Lda.

O presente trabalho debruça-se sobre a análise de fluxos de informação e materiais na empresa Dorel Portugal, Lda.. Mais concretamente, são analisados os fluxos de transmissão de informação e os fluxos de movimentação de materiais nos duais fornecedores/armazém e armazém/setor de montagem. O estudo referido terá como propósito a identificação de elementos, associados ao estado atual, passíveis e/ou carentes de melhoria. Identificados e nomeados os pontos de intervenção, desenvolvem-se propostas de solução, as quais assentam predominantemente nos princípios e ferramentas que se associam à filosofia Lean. A escolha desta filosofia, para fundamentação de propostas, prende-se com o facto de a mesma assentar numa lógica de criação de valor pela melhoria de processo, o que espelha bem a intensão subjacente a este exercício. Foram implementadas as sugestões apresentadas e validadas junto da entidade alvo de estudo. No seguimento das implementações realizadas foi executada uma análise que permite enaltecer o ganho, seja de forma quantitativa ou qualitativa, a fim de criar impacto e sensibilizar para a importância das ações executadas. Para finalizar, importa demarcar a criação de um plano de controlo, contemplado nas ações levadas a cabo, o qual é direcionado para a manutenção do processo e concretização de medidas de melhoria contínua.

Characterization of the abn2(yxiA) encoding a Bacillus subtilis GH43 arabinanase, Abn2, and its role in arabino-polysaccharides degradation.

Journal of Bacteriology (Junho 2008) 4272-4280

trans-Acting factors and cis elements involved in glucose repression of arabinan degradation in Bacillus subtilis.

Journal of Bacteriology (Nov 2007) 8371-8376

Optimizing the embedded heaters position in the pultrusion process using finite element analysis

This study is based on a previous experimental work in which embedded cylindrical heaters were applied to a pultrusion machine die, and resultant energetic performance compared with that achieved with the former heating system based on planar resistances. The previous work allowed to conclude that the use of embedded resistances enhances significantly the energetic performance of pultrusion process, leading to 57% decrease of energy consumption. However, the aforementioned study was developed with basis on an existing pultrusion die, which only allowed a single relative position for the heaters. In the present work, new relative positions for the heaters were investigated in order to optimize heat distribution process and energy consumption. Finite Elements Analysis was applied as an efficient tool to identify the best relative position of the heaters into the die, taking into account the usual parameters involved in the process and the control system already tested in the previous study. The analysis was firstly developed with basis on eight cylindrical heaters located in four different location plans. In a second phase, in order to refine the results, a new approach was adopted using sixteen heaters with the same total power. Final results allow to conclude that the correct positioning of the heaters can contribute to about 10% of energy consumption reduction, decreasing the production costs and leading to a better eco-efficiency of pultrusion process.

Design of New Materials for Passive Vibration Control

The objective of this contribution is to extend the models of cellular/composite material design to nonlinear material behaviour and apply them for design of materials for passive vibration control. As a first step a computational tool allowing determination of optimised one-dimensional isolator behaviour was developed. This model can serve as a representation for idealised macroscopic behaviour. Optimal isolator behaviour to a given set of loads is obtained by generic probabilistic metaalgorithm, simulated annealing. Cost functional involves minimization of maximum response amplitude in a set of predefined time intervals and maximization of total energy absorbed in the first loop. Dependence of the global optimum on several combinations of leading parameters of the simulated annealing procedure, like neighbourhood definition and annealing schedule, is also studied and analyzed. Obtained results facilitate the design of elastomeric cellular materials with improved behaviour in terms of dynamic stiffness for passive vibration control.

Schistosomiasis mansoni in an area of low transmission: I. impact of control measures

This work was undertaken in the municipality of Pedro de Toledo (São Paulo State, Brazil) in 1987, to clarify aspects related to the transmission levels of Schistosoma mansoni in a human population where the snail host is Biomphalaria tenagophila. Since 1980 a control programme has been undertaken in this municipality. Urban and rural populations (4,719 subjects) were submitted to faecal examinations (Kato-Katz method). The overall prevalence rate was 4.8% being higher in males (6.2%) and also in the rural zone (5.8%). The geometric mean of S. mansoni eggs was 35.1 eggs per gramme of faeces (epg). Approximately 80.0% of the carriers presented less than 100 epg and only 20 individuals (9.0%) eliminated more than half of total eggs. The highest index of potencial contamination (IPC) was in the age group of 5 to 20 years (57.6%). Two thirds of the investigated patients (207) were autochthonous of Pedro de Toledo. The geographical distribution of the carriers showed a clear aggregation of the autochthonous cases and a close association between human contact sites and breeding places of B. tenagophila. This study shows that schistosomiasis subjects were not randomly aggregated, the youngsters should be the main target in the prophylaxis, and the efficacy of the control programme.