Liquid-phase alcohol promoted methanol synthesis from CO2 and H2

Methanol is an important and versatile compound with various uses as a fuel and a feedstock chemical. Methanol is also a potential chemical energy carrier. Due to the fluctuating nature of renewable energy sources such as wind or solar, storage of energy is required to balance the varying supply and demand. Excess electrical energy generated at peak periods can be stored by using the energy in the production of chemical compounds. The conventional industrial production of methanol is based on the gas-phase synthesis from synthesis gas generated from fossil sources, primarily natural gas. Methanol can also be produced by hydrogenation of CO2. The production of methanol from CO2 captured from emission sources or even directly from the atmosphere would allow sustainable production based on a nearly limitless carbon source, while helping to reduce the increasing CO2 concentration in the atmosphere. Hydrogen for synthesis can be produced by electrolysis of water utilizing renewable electricity. A new liquid-phase methanol synthesis process has been proposed. In this process, a conventional methanol synthesis catalyst is mixed in suspension with a liquid alcohol solvent. The alcohol acts as a catalytic solvent by enabling a new reaction route, potentially allowing the synthesis of methanol at lower temperatures and pressures compared to conventional processes. For this thesis, the alcohol promoted liquid phase methanol synthesis process was tested at laboratory scale. Batch and semibatch reaction experiments were performed in an autoclave reactor, using a conventional Cu/ZnO catalyst and ethanol and 2-butanol as the alcoholic solvents. Experiments were performed at the pressure range of 30-60 bar and at temperatures of 160-200 °C. The productivity of methanol was found to increase with increasing pressure and temperature. In the studied process conditions a maximum volumetric productivity of 1.9 g of methanol per liter of solvent per hour was obtained, while the maximum catalyst specific productivity was found to be 40.2 g of methanol per kg of catalyst per hour. The productivity values are low compared to both industrial synthesis and to gas-phase synthesis from CO2. However, the reaction temperatures and pressures employed were lower compared to gas-phase processes. While the productivity is not high enough for large-scale industrial operation, the milder reaction conditions and simple operation could prove useful for small-scale operations. Finally, a preliminary design for an alcohol promoted, liquid-phase methanol synthesis process was created using the data obtained from the experiments. The demonstration scale process was scaled to an electrolyzer unit producing 1 Nm3 of hydrogen per hour. This Master’s thesis is closely connected to LUT REFLEX-platform.

Fukushima-derived radionuclides in sediments of the Japanese Pacific Ocean coast and various Japanese water samples (seawater, tap water, and coolant water of Fukushima Daiichi reactor unit 5)

We investigated Ocean sediments and seawater from inside the Fukushima exclusion zone and found radiocesium (134Cs and 137Cs) up to 800 Bq kg-1 as well as 90Sr up to 5.6 Bq kg-1. This is one of the first reports on radiostrontium in sea sediments from the Fukushima exclusion zone. Seawater exhibited contamination levels up to 5.3 Bq kg-1 radiocesium. Tap water from Tokyo from weeks after the accident exhibited detectable but harmless activities of radiocesium (well below the regulatory limit). Analysis of the Unit 5 reactor coolant (finding only 3H and even low 129I) leads to the conclusion that the purification techniques for reactor coolant employed at Fukushima Daiichi are very effective.

Photocatalytic Degradation of Anthracene in Closed System Reactor

Polycyclic aromatic hydrocarbons (PAHs) represent a large class of persistent organic pollutants in an environment of special concern because they have carcinogenic and mutagenic activity. In this paper, we focus on and discuss the effect of different parameters, for instance, initial concentration of Anthracene, temperature, and light intensity, on the degradation rate. These parameters were adjusted at pH 6.8 in the presence of the semiconductor materials (TiO2) as photocatalysts overUVlight. The main product of Anthracene photodegradation is 9,10-Anthraquinone which isidentified and compared with the standard compound by GC-MS. Our results indicate that the optimum conditions for the best rate of degradation are 25 ppm concentration of Anthracene, regulating the reaction vessel at 308.15 K and 2.5 mW/cm(2) of light intensity at 17 5mg/100 mL of titanium dioxide (P25).

Modular continuous crystallizer: operation, experimental arrangement and identification of process parameters

Crystallization is employed in different industrial processes. The method and operation can differ depending on the nature of the substances involved. The aim of this study is to examine the effect of various operating conditions on the crystal properties in a chemical engineering design window with a focus on ultrasound assisted cooling crystallization. Batch to batch variations, minimal manufacturing steps and faster production times are factors which continuous crystallization seeks to resolve. Continuous processes scale-up is considered straightforward compared to batch processes owing to increase of processing time in the specific reactor. In cooling crystallization process, ultrasound can be used to control the crystal properties. Different model compounds were used to define the suitable process parameters for the modular crystallizer using equal operating conditions in each module. A final temperature of 20oC was employed in all experiments while the operating conditions differed. The studied process parameters and configuration of the crystallizer were manipulated to achieve a continuous operation without crystal clogging along the crystallization path. The results from the continuous experiment were compared with the batch crystallization results and analysed using the Malvern Morphologi G3 instrument to determine the crystal morphology and CSD. The modular crystallizer was operated successfully with three different residence times. At optimal process conditions, a longer residence time gives smaller crystals and narrower CSD. Based on the findings, at a constant initial solution concentration, the residence time had clear influence on crystal properties. The equal supersaturation criterion in each module offered better results compared to other cooling profiles. The combination of continuous crystallization and ultrasound has large potential to overcome clogging, obtain reproducible and narrow CSD, specific crystal morphologies and uniform particle sizes, and exclusion of milling stages in comparison to batch processes.

In situ differentiation of labile/inert metal species in Brazilian tropical rivers by means of a time-controlled batch-procedure based on TEPHA resin

The present study deals with a new analytical procedure based on a cellulose diffusion membrane and immobilised tetraethylene-pentamine-hexaacetate chelator (DM-TEPHA) for an in situ differentiation of labile and inert metal species in aquatic systems. The DM-TEPHA system was prepared by placing TEPHA chelator in pre-purified cellulose bags and in situ applied immersing the system in two Brazilian rivers to study the relative lability of metal species (Cu, Pb, Fe, Mn and Ni) as a function of the time and the quantity of exchanger, respectively. The procedure is simple and enables a new perspective for understanding the complexation, transport, stability and lability of metal species in aquatic systems rich in organic matter.

Caracterización de bacterias filamentosas en el funcionamiento de un reactor aerobio de la planta de tratamiento de aguas residuales de origen cervecero

La actividad industrial y el desarrollo material y económico, han traído como consecuencia la contaminación del aire, agua y el suelo; lo que ocasiona modificaciones físicas químicas y biológicas que han producido un deterioro en la calidad del agua, dando como resultado problemas de contaminación que afectan tanto la productividad de los sistemas como la salud humana. A las aguas de composición variada provenientes de uso municipal, industrial, comercial, agrícola, pecuario, o de cualquier otra índole, ya sea privada o pública que han sufrido una degradación o alteración en su calidad original se le conoce como agua residual. Este trabajo tiene como objetivo “Caracterizar las bacterias filamentosas en el funcionamiento de un reactor aerobio de la planta de tratamiento de aguas residuales de origen cervecero” para ello se estudió durante varios meses los parámetros físico-químicos y biológicos para poder así controlar de las bacterias filamentosas y así evitar en un futuro problemas de operación o poder controlar su crecimiento y por ende, ecológicos dentro del sistema de lodos activados. La identificación se realizó tomando muestras en el reactor aerobio y realizándole la tinción de Gram para posteriormente ser vistos en un microscopio de una resolución de 100x; luego se caracterizaron las bacterias juntas con los parámetros de operación del tanque de lodos por muestra y los resultados encontrados fueron la presencia de filamentos Microtrix Parvicella, Tipo 021N, y Sp1 (llamada así por no ser identificada, ni encontrada en la literatura), esta es una nueva especie encontrada, ya que es propia de este reactor aerobio y crecen principalmente en aguas cerveceras y por deficiencia de nutrientes en el sistema. Este trabajo nos permitió conocer la dinámica que existe entre los parámetros fisicoquímicos y los microorganismos que se encuentran en un biorreactor Aerobio. Esto nos llevó a comprender mejor el funcionamiento de estos sistemas dentro de plantas de aguas residuales de tipo industrial. ABSTRACT Industrial activity and the physical and economic development have resulted in contamination of air, water and soil, causing physical chemical and biological changes that have produced deterioration in water quality, resulting in pollution problems affects the productivity of the systems and human health. A varied composition waters from municipal, industrial, commercial, agricultural, livestock, or any other use, whether private or public who have suffered a degradation or alteration in their original quality is known as residual water. This work aims to "characterize filamentous bacteria in the operation of an aerobic reactor plant wastewater treatment brewer origin" for this physicochemical and biological parameters were studied for several months to thereby control bacteria stringy and avoid future problems in operation or to control their growth and thus ecological This work aims to "characterize filamentous bacteria in the operation of an aerobic reactor plant wastewater treatment brewer origin" for this physicochemical and biological parameters were studied for several months to thereby control bacteria stringy and avoid future problems in operation or to control their growth and thus ecological within the activated sludge system. This work allowed us to understand the dynamics between physicochemical parameters and microorganisms found in an aerobic bioreactor. This led us to better understand the operation of these systems within plants industrial wastewater.

Síntesis de BaBiO₃ y Sr₂Bi₂O₅ para su evaluación en procesos fotoinducidos en la degradación de rodamina b y conversión del agua.

Propósito y Método del estudio: En este trabajo se estudió la influencia del método de síntesis en las propiedades fisicoquímicas, fotocatalíticas y fotoelectroquímicas del BaBiO3 y el Sr2Bi2O5. En primera instancia, se realizó la síntesis de los materiales por la técnica de estado sólido (pos-tratamiento con molienda mecánica) e hidrotermal. Para la síntesis en hidrotermal se exploraron 3 diferentes temperaturas: 130, 150, 170 °C. Los materiales obtenidos fueron caracterizados mediante Difracción de Rayos-X (DRX), Espectroscopía de Reflectancia Difusa (ERD), Microscopía Electrónica de Barrido (MEB) y Fisisorción de Nitrógeno. Posteriormente se realizó la evaluación de las propiedades fotocatalíticas de los materiales obtenidos en la degradación de rodamina B. Las pruebas fotocatalíticas se realizaron en un reactor tipo Batch, utilizando una lámpara de Xenón de 6000 K. El estudio fotocatalítico finalizó con el cálculo de parámetros cinéticos tales como la constante de velocidad aparente (k) y tiempo de vida media (t1/2). Los resultados mostraron que el BaBiO3 sintetizado por reacción de estado sólido presentó la mayor eficiencia fotocatalitica. Para incrementar la eficiencia fotocatalitica de los materiales sintetizados se adicionaron superficialmente partículas de NiO en porcentajes de 3, 5 y 10 % al bismutato de estroncio y bario, utilizando para ello el método de impregnación. Los materiales fueron caracterizados y probados en la degradación de rodamina B. Por otro lado, para conocer el grado de eficiencia de los materiales se realizó el estudio fotoelectroquímico para determinar la posición de las bandas de conducción y valencia de cada uno de ellos. El grado de mineralización de la rodamina B se analizó mediante análisis de Carbón Orgánico Total (COT) y adicionalmente se realizaron pruebas de reproducibilidad para determinar la estabilidad de los materiales ante la exposición de ciclos sucesivos de irradiación. Contribuciones y conclusiones: Se lograron obtener los Bismutatos de Estroncio y Bario mediante la reacción en estado sólido a 800 y 900 °C. Mientras que por el método de hidrotermal se obtuvieron los materiales a 130, 150 y 170°C, seguido de un tratamiento térmico a 700°C. Los resultados de electroquímica mostraron que el material de Sr2Bi2O5 es apto para generar procesos de oxidación y reducción. La adición de NiO no proporcionó mejora en la eficiencia fotocatalítica, lo que se atribuyó a las aglomeraciones de partículas sobre la superficie de los materiales. Los materiales obtenidos por estado sólido presentaron la mayor actividad fotocatalítica en degradación de rodamina B, comparados con los obtenidos por el método de hidrotermal, por lo que el factor que domina la actividad fotocatalítica de estos materiales fue principalmente la cristalinidad. Además los materiales presentaron buena estabilidad ante ciclos sucesivos de irradiación y mostraron un buen grado de mineralización de la rodamina B.

MULTI-UNIT ACCIDENT CONTRIBUTIONS TO U.S. NUCLEAR REGULATORY COMMISSION QUANTITATIVE HEALTH OBJECTIVES: A SAFETY GOAL POLICY ANALYSIS USING MODELS FROM STATE-OF-THE-ART REACTOR CONSEQUENCE ANALYSES

The U.S. Nuclear Regulatory Commission implemented a safety goal policy in response to the 1979 Three Mile Island accident. This policy addresses the question “How safe is safe enough?” by specifying quantitative health objectives (QHOs) for comparison with results from nuclear power plant (NPP) probabilistic risk analyses (PRAs) to determine whether proposed regulatory actions are justified based on potential safety benefit. Lessons learned from recent operating experience—including the 2011 Fukushima accident—indicate that accidents involving multiple units at a shared site can occur with non-negligible frequency. Yet risk contributions from such scenarios are excluded by policy from safety goal evaluations—even for the nearly 60% of U.S. NPP sites that include multiple units. This research develops and applies methods for estimating risk metrics for comparison with safety goal QHOs using models from state-of-the-art consequence analyses to evaluate the effect of including multi-unit accident risk contributions in safety goal evaluations.

Assessment of naproxen adsorption on bone char in aqueous solutions using batch and fixed-bed processes

An integrated analysis of naproxen adsorption on bone char in batch and packed-bed column conditions has been performed. Kinetic, thermodynamic and breakthrough parameters have been calculated using adsorption models and artificial neural networks. Results show that naproxen removal using bone char in batch conditions is a feasible and effective process, which could involve electrostatic and non-electrostatic interactions depending mainly on pH conditions. However, the application of packed-bed column for naproxen adsorption on bone char is not effective for the treatment of diluted solutions due to the low degree of adsorbent utilization (below 4%) at tested operating conditions. The proposed mechanism for naproxen removal using bone char could include a complexation process via phosphate and naproxen, hydrogen bonding and the possibility of hydrophobic interactions via π–π electron. This study highlights the relevance of performing an integrated analysis of adsorbent effectiveness in batch and dynamic conditions to establish the best process configuration for the removal of emerging water pollutants such as pharmaceuticals.

Removal of paracetamol on biomass-derived activated carbon: Modeling the fixed bed breakthrough curves using batch adsorption experiments

The remediation of paracetamol (PA), an emerging contaminant frequently found in wastewater treatment plants, has been studied in the low concentration range (0.3–10 mg L−1) using as adsorbent a biomass-derived activated carbon. PA uptake of up to 100 mg g−1 over the activated carbon has been obtained, with the adsorption isotherms being fairly explained by the Langmuir model. The application of Reichemberg and the Vermeulen equations to the batch kinetics experiments allowed estimating homogeneous and heterogeneous diffusion coefficients, reflecting the dependence of diffusion with the surface coverage of PA. A series of rapid small-scale column tests were carried out to determine the breakthrough curves under different operational conditions (temperature, PA concentration, flow rate, bed length). The suitability of the proposed adsorbent for the remediation of PA in fixed-bed adsorption was proven by the high PA adsorption capacity along with the fast adsorption and the reduced height of the mass transfer zone of the columns. We have demonstrated that, thanks to the use of the heterogeneous diffusion coefficient, the proposed mathematical approach for the numerical solution to the mass balance of the column provides a reliable description of the breakthrough profiles and the design parameters, being much more accurate than models based in the classical linear driving force.

A SCR Model based on Reactor and Engine Experimental Studies for a Cu-zeolite Catalyst

A NOx reduction efficiency higher than 95% with NH3 slip less than 30 ppm is desirable for heavy-duty diesel (HDD) engines using selective catalytic reduction (SCR) systems to meet the US EPA 2010 NOx standard and the 2014-2018 fuel consumption regulation. The SCR performance needs to be improved through experimental and modeling studies. In this research, a high fidelity global kinetic 1-dimensional 2-site SCR model with mass transfer, heat transfer and global reaction mechanisms was developed for a Cu-zeolite catalyst. The model simulates the SCR performance for the engine exhaust conditions with NH3 maldistribution and aging effects, and the details are presented. SCR experimental data were collected for the model development, calibration and validation from a reactor at Oak Ridge National Laboratory (ORNL) and an engine experimental setup at Michigan Technological University (MTU) with a Cummins 2010 ISB engine. The model was calibrated separately to the reactor and engine data. The experimental setup, test procedures including a surrogate HD-FTP cycle developed for transient studies and the model calibration process are described. Differences in the model parameters were determined between the calibrations developed from the reactor and the engine data. It was determined that the SCR inlet NH3 maldistribution is one of the reasons causing the differences. The model calibrated to the engine data served as a basis for developing a reduced order SCR estimator model. The effect of the SCR inlet NO2/NOx ratio on the SCR performance was studied through simulations using the surrogate HD-FTP cycle. The cumulative outlet NOx and the overall NOx conversion efficiency of the cycle are highest with a NO2/NOx ratio of 0.5. The outlet NH3 is lowest for the NO2/NOx ratio greater than 0.6. A combined engine experimental and simulation study was performed to quantify the NH3 maldistribution at the SCR inlet and its effects on the SCR performance and kinetics. The uniformity index (UI) of the SCR inlet NH3 and NH3/NOx ratio (ANR) was determined to be below 0.8 for the production system. The UI was improved to 0.9 after installation of a swirl mixer into the SCR inlet cone. A multi-channel model was developed to simulate the maldistribution effects. The results showed that reducing the UI of the inlet ANR from 1.0 to 0.7 caused a 5-10% decrease in NOx reduction efficiency and 10-20 ppm increase in the NH3 slip. The simulations of the steady-state engine data with the multi-channel model showed that the NH3 maldistribution is a factor causing the differences in the calibrations developed from the engine and the reactor data. The Reactor experiments were performed at ORNL using a Spaci-IR technique to study the thermal aging effects. The test results showed that the thermal aging (at 800°C for 16 hours) caused a 30% reduction in the NH3 stored on the catalyst under NH3 saturation conditions and different axial concentration profiles under SCR reaction conditions. The kinetics analysis showed that the thermal aging caused a reduction in total NH3 storage capacity (94.6 compared to 138 gmol/m3), different NH3 adsorption/desorption properties and a decrease in activation energy and the pre-exponential factor for NH3 oxidation, standard and fast SCR reactions. Both reduction in the storage capability and the change in kinetics of the major reactions contributed to the change in the axial storage and concentration profiles observed from the experiments.