Soodakattilalaitosten energiantuotannon lisääminen

The aim of this thesis is to study different methods to increase the energy production of recovery boilers. This improvement is encouraged by the current energy policy and the rapid rise in energy prices, especially in electricity. In addition, the energy efficiency of the power plants is intended to be improved. There are several methods to increase the energy production. The methods taken into more accurate study are lower pressure steam for soot blowing and flue gas coolers. Energy balances are made for these two cases to check a plausible addition of power generation of turbo-generator of the steam turbine. Also, the viability issues are studied. Solvo Power Plant Simulation program is used for the energy balance research. Two case power plants are simulated to solve the balances. To solve the addition of power generation with the flue gas coolers, basic balance calculation is performed. The viabilities are also taken into account, especially the payback times of these alternatives. On the basis of the results, installing the system to the process is viable in both cases. By installing the lowest possible pressure steam system for the soot blowing, the advantages are the most significant. The investment costs are the highest but the payback time is less than 1,5 years and the profit in the next 20 years is the greatest. In the case of flue gas coolers, the results did not entirely agree with past studies. Nevertheless, installing the flue gas coolers into the process also seems to be significant and profitable.

Säilöntämenetelmien parantaminen höyryvoimaprosessissa

Lahti Energia Oy:n kivihiiltä polttavan Kymijärvi I voimalaitoksen vuotuiset käyttötunnit ovat vähentyneet. Syy vähennykseen on ollut uuden kaasutusvoimalaitoksen käyttöönotto vuonna 2012, jolloin vanhan voimalaitoksen käytölle ei ole ollut tarvetta kesäkuukausina. Seisonta-aikana voimalaitoksen höyryvoimaprosessi tulee säilöä. Säilönnällä tarkoitetaan toimenpiteitä, joilla estetään korroosio-olosuhteiden syntyminen voimalaitoksen laitteisiin. Säilöntätavasta riippuen estetään joko hapen tai kosteuden esiintyminen. Tässä diplomityössä tutkitaan eri säilöntämenetelmien ominaisuuksia tavoitteena löytää sopivin vaihtoehto vanhalle kivihiilivoimalaitokselle. Työssä perehdytään teorian kautta kolmeen menetelmään voimalaitoksen kattilan säilönnässä. Typpi- ja märkäsäilönnässä estetään hapen ja kuivailmasäilönnässä kosteuden esiintyminen. Työssä on myös tutkittu kattilan säilöntämenetelmien vaikutuksia muihin laitteistoihin ja järjestelmiin. Tuloksien perusteella voidaan todeta, että kuivailmasäilöntä on toimivin ratkaisu voimalaitoksen viimeisille käyttövuosille. Voimalaitoksen jäädessä varavoimalaitokseksi on typpisäilöntä kustannustehokkain vaihtoehto.

Modeling of high pressure pretreatment process for gold leaching

Investigation of high pressure pretreatment process for gold leaching is the objective of the present master's thesis. The gold ores and concentrates which cannot be easily treated by leaching process are called "refractory". These types of ores or concentrates often have high content of sulfur and arsenic that renders the precious metal inaccessible to the leaching agents. Since the refractory ores in gold manufacturing industry take a considerable share, the pressure oxidation method (autoclave method) is considered as one of the possible ways to overcome the related problems. Mathematical modeling is the main approach in this thesis which was used for investigation of high pressure oxidation process. For this task, available information from literature concerning this phenomenon, including chemistry, mass transfer and kinetics, reaction conditions, applied apparatus and application, was collected and studied. The modeling part includes investigation of pyrite oxidation kinetics in order to create a descriptive mathematical model. The following major steps are completed: creation of process model by using the available knowledge; estimation of unknown parameters and determination of goodness of the fit; study of the reliability of the model and its parameters.

Comparison of Biomass Gasification Technologies for Natural Gas Substitution in Iron Ore Pelletizing Plants

The iron ore pelletizing process consumes high amounts of energy, including nonrenewable sources, such as natural gas. Due to fossil fuels scarcity and increasing concerns regarding sustainability and global warming, at least partial substitution by renewable energy seems inevitable. Gasification projects are being successfully developed in Northern Europe, and large-scale circulating fluidized bed biomass gasifiers have been commissioned in e.g. Finland. As Brazil has abundant biomass resources, biomass gasification is a promising technology in the near future. Biomasses can be converted into product gas through gasification. This work compares different technologies, e.g. air, oxygen and steam gasification, focusing on the use of the product gas in the indurating machine. The use of biosynthetic natural gas is also evaluated. Main parameters utilized to assess the suitability of product gas were adiabatic flame temperature and volumetric flow rate. It was found that low energy content product gas could be utilized in the traveling grate, but it would require burner’s to be changed. On the other hand, bio-SGN could be utilized without any adaptions. Economical assessment showed that all gasification plants are feasible for sizes greater than 60 MW. Bio-SNG production is still more expensive than natural gas in any case.

Development of a process for the direct synthesis of hydrogen peroxide in a novel microstructured reactor

Microreactors have proven to be versatile tools for process intensification. Over recent decades, they have increasingly been used for product and process development in chemical industries. Enhanced heat and mass transfer in the reactors due to the extremely high surfacearea- to-volume ratio and interfacial area allow chemical processes to be operated at extreme conditions. Safety is improved by the small holdup volume of the reactors and effective control of pressure and temperature. Hydrogen peroxide is a powerful green oxidant that is used in a wide range of industries. Reduction and auto-oxidation of anthraquinones is currently the main process for hydrogen peroxide production. Direct synthesis is a green alternative and has potential for on-site production. However, there are two limitations: safety concerns because of the explosive gas mixture produced and low selectivity of the process. The aim of this thesis was to develop a process for direct synthesis of hydrogen peroxide utilizing microreactor technology. Experimental and numerical approaches were applied for development of the microreactor. Development of a novel microreactor was commenced by studying the hydrodynamics and mass transfer in prototype microreactor plates. The prototypes were designed and fabricated with the assistance of CFD modeling to optimize the shape and size of the microstructure. Empirical correlations for the mass transfer coefficient were derived. The pressure drop in micro T-mixers was investigated experimentally and numerically. Correlations describing the friction factor for different flow regimes were developed and predicted values were in good agreement with experimental results. Experimental studies were conducted to develop a highly active and selective catalyst with a proper form for the microreactor. Pd catalysts supported on activated carbon cloths were prepared by different treatments during the catalyst preparation. A variety of characterization methods were used for catalyst investigation. The surface chemistry of the support and the oxidation state of the metallic phase in the catalyst play important roles in catalyst activity and selectivity for the direct synthesis. The direct synthesis of hydrogen peroxide was investigated in a bench-scale continuous process using the novel microreactor developed. The microreactor was fabricated based on the hydrodynamic and mass transfer studies and provided a high interfacial area and high mass transfer coefficient. The catalysts were prepared under optimum treatment conditions. The direct synthesis was conducted at various conditions. The thesis represents a step towards a commercially viable direct synthesis. The focus is on the two main challenges: mitigating the safety problem by utilization of microprocess technology and improving the selectivity by catalyst development.

Häiriöanalyysejä tehonkorotetun kiehutusvesivoimalaitoksen käytettävyyden varmistamiseksi

TVO suunnittelee reaktoritehon 10 %:n korotusta Olkiluoto 1 ja 2 -voimalaitoksille. Reaktoriteho nostetaan 2500 MW:sta 2750 MW:iin polttoaineen rikastusastetta nostamalla ja pääkiertovirtausta kasvattamalla. Samalla syöttövesivirtaus reaktoriin ja tuorehöyryvirtaus turpiineille kasvaa. Lauhteenpuhdistusjärjestelmän kapasiteettia ei voida kuitenkaan kasvattaa, joten massavirran lisäys toteutetaan ottamalla käyttöön korkeapainesivulauhteen eteenpäinpumppaus. Lauhteen esilämmityslinjojen, lauhteenpuhdistuksen ja syöttövesipumppujen massavirta säilyy siten nykyisellään. Muita merkittäviä tehonkorotukseen liittyviä laitosmuutoksia ovat pääkiertopumppujen uusinta ja korkeapaineturpiinin muutokset. Tehonkorotetun prosessin käytettävyyden varmistamiseksi tehdään häiriöanalyysejä Apros-prosessisimulointiohjelmistoa käyttäen. OL1 ja OL2 -laitoksista on olemassa validoitu 2500 MW:n laitosmalli, josta muokatulla 2750 MW:n laitosmallilla simuloinnit tehdään. Häiriöanalyysien avulla selvitetään säätöjärjestelmien kyky pitää prosessin tila hallinnassa ilman suojausautomaation laukeamista. Simuloituihin tapauksiin kuuluu pumppujen ja venttiilien vikaantumistapauksia sekä turpiini- ja reaktoripuolen pikasulku- ja osittaispikasulkutapauksia. Myös meriveden lämpötilan vaikutusta häiriötilanteisiin tarkastellaan. Analyysien perusteella voimalaitosten ohjaus- ja suojausautomaatio toimivat hyvin myös korotetulla teholla. Tehonkorotuksen jälkeiset suuremmat massavirrat aiheuttavat kuitenkin voimakkaampia reaktoripaineen ja -tehon vaihteluita varsinkin venttiilien sulkeutumistapauksissa. Simuloinnit osoittivat, että tehonkorotus 2500 MW:sta 2750 MW:iin on mahdollinen, mutta aiheuttaa pieniä muutoksia laitoksen suojausjärjestelmien laukaisurajoihin.

Preparation for ramp-up production process in metal manufacturin

Collaboration is essential for successful new product development. In the preparation for ramp-up production collaboration between R&D and supply chain functions is crucial. This thesis examines the meaning of collaboration and the effects of collaboration between R&D and supply chain. The aim of this thesis is to analyse and advice on how to improve the collaboration between the research and development department and supply chain within the preparation for rampup process. This thesis begins by introducing the reader to the product development methodologies and collaboration literature. The following part of the thesis describes the current situation and the results of the qualitative research. The last part of the thesis will explain the improvement suggestions. The main improvement suggestions are clarification of the processes and responsibilities and the introduction of a kick-off meeting.

Model based analysis of the post-combustion calcium looping process for carbon dioxide capture

This thesis presents a one-dimensional, semi-empirical dynamic model for the simulation and analysis of a calcium looping process for post-combustion CO2 capture. Reduction of greenhouse emissions from fossil fuel power production requires rapid actions including the development of efficient carbon capture and sequestration technologies. The development of new carbon capture technologies can be expedited by using modelling tools. Techno-economical evaluation of new capture processes can be done quickly and cost-effectively with computational models before building expensive pilot plants. Post-combustion calcium looping is a developing carbon capture process which utilizes fluidized bed technology with lime as a sorbent. The main objective of this work was to analyse the technological feasibility of the calcium looping process at different scales with a computational model. A one-dimensional dynamic model was applied to the calcium looping process, simulating the behaviour of the interconnected circulating fluidized bed reactors. The model incorporates fundamental mass and energy balance solvers to semi-empirical models describing solid behaviour in a circulating fluidized bed and chemical reactions occurring in the calcium loop. In addition, fluidized bed combustion, heat transfer and core-wall layer effects were modelled. The calcium looping model framework was successfully applied to a 30 kWth laboratory scale and a pilot scale unit 1.7 MWth and used to design a conceptual 250 MWth industrial scale unit. Valuable information was gathered from the behaviour of a small scale laboratory device. In addition, the interconnected behaviour of pilot plant reactors and the effect of solid fluidization on the thermal and carbon dioxide balances of the system were analysed. The scale-up study provided practical information on the thermal design of an industrial sized unit, selection of particle size and operability in different load scenarios.

The effects of the service process on satisfaction, trust and value as creators of customer loyalty in a daily deals concept

This study aims at applying the customer behaviour studies of satisfaction, trust, perceived value and loyalty to a daily deals concept. The goal is to find out whether the relationships are the same in this specific context when compared to previous e-commerce studies. The study examines how the daily deals service process affects customer satisfaction, trust and value, and how these in turn impact customer loyalty and each other. The data was collected via e-mail survey from case company customers, and research was conducted on a quantitative basis by using multivariate methods as tools. The results suggest that daily deals service process and service quality do have a direct and positive effect on customer satisfac-tion, trust and value. Additionally, positive correlations between the latter variables and customer loyalty were found. The results imply that the daily deals concept does not differ from other e-services when considering the studied factors. The results also emphasize the importance of recognizing what determinants have the greatest impact on customer loyalty in this specific context.

Effect of additives, precursors and process conditions on particle morphology

The objective of the thesis was to develop methods to manufacture and control calcium carbonate crystal nucleation and growth in precipitation process. The work consists of experimental part and literature part that addresses theory of nucleation, crystallization and precipitation. In the experimental part calcium carbonate was precipitated using carbonization reaction. Precipitation was carried out in presence of known morphology controlling agents (anionic polymers and sodium silicate) and by using different operation conditions. Formed material was characterized using SEM images, and its thermal stability was assessed. This work demonstrates that carbon dioxide feeding rate and concentrations of calcium hydroxide and additives can be used to control size, shape and amount of precipitating calcium carbonate.

Determination of collector chemicals from flotation process waters using capillary electrophoresis

Vaahdotusprosessia käytetään yleisesti erottamaan arvokkaita mineraaleja malmeista. Toimiakseen tehokkaasti prosessi tarvitsee kokoojakemikaaleja, joiden tehtävänä on sitoa halutut mineraalit ilmakupliin. Jotta näiden kemikaalien käyttäytymistä prosessissa voitaisiin ymmärtää paremmin ja prosessin ohjausta tehostaa, pitää kokoojia pystyä analysoimaan prosessivesistä. Työn kirjallisuusosassa on koottu ja vertailtu erilaisia kirjallisuudesta löytyneitä analyysimenetelmiä kokoojakemikaaleille. Kokeellisessaosassa on kehitetty kaksi kapillaarielektroforeesimenetelmää näiden kemikaalien tutkimiseen. Menetelmien toteamisrajat tutkituille kemikaaleille olivat seuraavanlaiset: natrium diiosobutylditiofosfaattille (DTP) 2,7 mg/L puhtaassa vedessä ja 6,7 mg/L prosessivedessä; natrium diisobutyldithiofosfinaatille (DTPI) vastaavasti 4,5 mg/L ja 6,7 mg/L; etyyli ksantaatille 0,025 mg/L ja 0,16 mg/L; ja isobutyyli ksantaatille 0,41 mg/L ja 0,62 mg/L. Näitä menetelmiä voidaan tulevaisuudessa kehittää kokoojien hajoamistuotteiden analysointia varten sekä prosessien on-line mittauksiin.

Improving the competitiveness of electrolytic Zinc process by chemical reaction engineering approach

This doctoral thesis describes the development work performed on the leachand purification sections in the electrolytic zinc plant in Kokkola to increase the efficiency in these two stages, and thus the competitiveness of the plant. Since metallic zinc is a typical bulk product, the improvement of the competitiveness of a plant was mostly an issue of decreasing unit costs. The problems in the leaching were low recovery of valuable metals from raw materials, and that the available technology offered complicated and expensive processes to overcome this problem. In the purification, the main problem was consumption of zinc powder - up to four to six times the stoichiometric demand. This reduced the capacity of the plant as this zinc is re-circulated through the electrolysis, which is the absolute bottleneck in a zinc plant. Low selectivity gave low-grade and low-value precipitates for further processing to metallic copper, cadmium, cobalt and nickel. Knowledge of the underlying chemistry was poor and process interruptions causing losses of zinc production were frequent. Studies on leaching comprised the kinetics of ferrite leaching and jarosite precipitation, as well as the stability of jarosite in acidic plant solutions. A breakthrough came with the finding that jarosite could precipitate under conditions where ferrite would leach satisfactorily. Based on this discovery, a one-step process for the treatment of ferrite was developed. In the plant, the new process almost doubled the recovery of zinc from ferrite in the same equipment as the two-step jarosite process was operated in at that time. In a later expansion of the plant, investment savings were substantial compared to other technologies available. In the solution purification, the key finding was that Co, Ni, and Cu formed specific arsenides in the “hot arsenic zinc dust” step. This was utilized for the development of a three-step purification stage based on fluidized bed technology in all three steps, i.e. removal of Cu, Co and Cd. Both precipitation rates and selectivity increased, which strongly decreased the zinc powder consumption through a substantially suppressed hydrogen gas evolution. Better selectivity improved the value of the precipitates: cadmium, which caused environmental problems in the copper smelter, was reduced from 1-3% reported normally down to 0.05 %, and a cobalt cake with 15 % Co was easily produced in laboratory experiments in the cobalt removal. The zinc powder consumption in the plant for a solution containing Cu, Co, Ni and Cd (1000, 25, 30 and 350 mg/l, respectively), was around 1.8 g/l; i.e. only 1.4 times the stoichiometric demand – or, about 60% saving in powder consumption. Two processes for direct leaching of the concentrate under atmospheric conditions were developed, one of which was implemented in the Kokkola zinc plant. Compared to the existing pressure leach technology, savings were obtained mostly in investment. The scientific basis for the most important processes and process improvements is given in the doctoral thesis. This includes mathematical modeling and thermodynamic evaluation of experimental results and hypotheses developed. Five of the processes developed in this research and development program were implemented in the plant and are still operated. Even though these processes were developed with the focus on the plant in Kokkola, they can also be implemented at low cost in most of the zinc plants globally, and have thus a great significance in the development of the electrolytic zinc process in general.

Biovoimalaitoksen energiatehokkuuden parantaminen ja osakuorma-ajon optimointi

Energiatehokkuus on nykyaikana yksi tärkeimmistä energiataloudellisista tekijöistä voimalaitosten sähköntuotannossa. Varsinkin yhteistuotantolaitoksissa joissa sähkö on lämpöenergian lisänä saatava sivutuote, sähkön tuotannon optimointi voi merkitä laitostalouden ja yrityksen kannalta huomattavia lisätuloja tai -säästöjä. Kaukaan Voima Oy:n biovoimalaitos on vuonna 2009 kaupalliseen käyttöön valmistunut moderni yhteistuotantolaitos, joka sijaitsee Lappeenrannassa UPM Kaukas sellutehtaan tehdasalueella. Voimalaitos tuottaa kaukolämpöä ja sähköä Lappeenrannan kaupungille sekä prosessihöyryä ja sähköä UPM Kaukaan tehtaille. Tämän työn tavoitteena on tarkastella biovoimalaitoksen omakäyttösähkön kulutusta kuukausitasolla verrattuna laitoksella tuotettavan höyryn määrään sekä etsiä voimalaitokselta kohteita, joiden omakäyttösähkön kulutusta voidaan vähentää vaikuttamatta höyryntuotantoon ja näin parantaa laitoksen energiatehokkuutta ja hyötysuhdetta. Työ rajataan käsittelemään voimalaitoksen apulaitteiden ja -järjestelmien omakäyttösähkön kulutusta. Työssä tarkastellaan vuodenaikojen vaihtelun ja kaukolämmön sekä prosessihöyryn tarpeen muutoksen vaikutusta voimalaitoksen ajomalliin sekä höyryntuotannon ja omakäyttösähkön kulutuksen suhteisiin. Työssä esiin nousseiden kohteiden potentiaaliset sähköenergian säästöt ovat noin 2500 MWh vuodessa joka tarkoittaa keskimäärin 3,7 % vähennystä voimalaitoksen kuukausittaiseen omakäyttösähkön kulutukseen. Kohteet eivät käytännössä vaadi minkaanlaista investointirahaa, vaan uusia ajojärjestelyitä. Keskeisimmiksi säästökohteiksi valikoitui laitoksen pumppausjärjestelmien paineenalennukset.

Computational studies for the design of process equipment with complex geometries

This study combines several projects related to the flows in vessels with complex shapes representing different chemical apparata. Three major cases were studied. The first one is a two-phase plate reactor with a complex structure of intersecting micro channels engraved on one plate which is covered by another plain plate. The second case is a tubular microreactor, consisting of two subcases. The first subcase is a multi-channel two-component commercial micromixer (slit interdigital) used to mix two liquid reagents before they enter the reactor. The second subcase is a micro-tube, where the distribution of the heat generated by the reaction was studied. The third case is a conventionally packed column. However, flow, reactions or mass transfer were not modeled. Instead, the research focused on how to describe mathematically the realistic geometry of the column packing, which is rather random and can not be created using conventional computeraided design or engineering (CAD/CAE) methods. Several modeling approaches were used to describe the performance of the processes in the considered vessels. Computational fluid dynamics (CFD) was used to describe the details of the flow in the plate microreactor and micromixer. A space-averaged mass transfer model based on Fick’s law was used to describe the exchange of the species through the gas-liquid interface in the microreactor. This model utilized data, namely the values of the interfacial area, obtained by the corresponding CFD model. A common heat transfer model was used to find the heat distribution in the micro-tube. To generate the column packing, an additional multibody dynamic model was implemented. Auxiliary simulation was carried out to determine the position and orientation of every packing element in the column. This data was then exported into a CAD system to generate desirable geometry, which could further be used for CFD simulations. The results demonstrated that the CFD model of the microreactor could predict the flow pattern well enough and agreed with experiments. The mass transfer model allowed to estimate the mass transfer coefficient. Modeling for the second case showed that the flow in the micromixer and the heat transfer in the tube could be excluded from the larger model which describes the chemical kinetics in the reactor. Results of the third case demonstrated that the auxiliary simulation could successfully generate complex random packing not only for the column but also for other similar cases.