Evaluation of thermal stress indexes for dairy cows in tropical regions

Seis índices de estresse ambiental foram aplicados a 1.359 dados de 359 vacas Holandesas e 54 vacas Jersey em rebanhos comerciais do Ceará e Rio Grande do Norte. O critério de seleção aplicado aos índices foi sua correlação com a temperatura retal e a freqüência respiratória dos animais. O Índice de Temperatura e Umidade (THI) e o Índice de Globo e Umidade (BGHI) apresentaram os piores resultados, com correlações muito baixas com as respostas dos animais. Os índices escolhidos foram o Índice de Temperatura Equivalente (ESI), correlacionado significativamente com a temperatura retal (r = 0,293) e a freqüência respiratória (r = 0,520), e o Índice de Carga Térmica (HLI), com correlações r = 0,286 e r = 0,542 respectivamente.

Variação anual de características morfológicas e da temperatura de superfície do pelame de vacas da raça Holandesa em ambiente semiárido

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Variação anual de hormônios tireoideanos e características termorreguladoras de vacas leiteiras em ambiente quente

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Mecanismos de desgaste de poliuretano em ensaios de microabrasão

Wear mechanisms and thermal history of two non-conforming sliding surfaces was investigated in laboratory. A micro-abrasion testing setup was used but the traditional rotative sphere method was substituted by a cylindrical surface of revolution which included seven sharp angles varying between 15o to 180o. The micro-abrasion tests lead to the investigation on the polyurethane response at different contact pressures. For these turned counterfaces with and without heat treatment. Normal load and sliding speeds were changed. The sliding distance was fixed at 5 km in each test. The room and contact temperatures were measured during the tests. The polyurethane was characterized using tensile testing, hardness Shore A measurement, Thermogravimetric Analysis (TGA), Differential Scanning Calorimetry (DSC) and Thermomechanical Analyze (TMA). The Vickers micro-hardness of the steel was measured before and after the heat treatment and the metallographic characterization was also carried out. Worn surface of polyurethane was analysed using Scanning Electron Microscope (SEM) and EDS (Electron Diffraction Scanning) microanalyses. Single pass scratch testing in polyurethane using indenters with different contact angles was also carried out. The scar morphology of the wear, the wear mechanism and the thermal response were analyzed in order to correlate the conditions imposed by the pressure-velocity pair to the materials in contact. Eight different wear mechanisms were identified on the polyurethane surface. It was found correlation between the temperature variation and the wear scar morphology.

Compósito Polimérico Híbrido: Comportamento Mecãnico, Descotinuidade Geométrica e Resistência Residual

The growing demand in the use of hybrid composite materials makes it essential a better understanding of their behavior face of various design conditions, such as the presence of geometric discontinuities in the cross section of structural elements. This way, the purpose of this dissertation is a study of the mechanical response (strength and stiffness), modes (characteristics) of fracture and Residual Strength of an hybrid polymeric composite with and without a geometric discontinuity in its longitudinal section (with a reduction in the cross section) loaded by uniaxial tension. This geometric discontinuity is characterized by central holes of different diameters. The hybrid composite was fabricated as laminate (plate) and consisting of ortho-tereftalic polyester matrix reinforced by 04 outer layers of Jute fibers bidirectional fabrics and 01 central layer of E-glass bidirectional fabric. The laminate was industrially manufactured (Tecniplas Nordeste Indústria e Comércio Ltda.), obtained by the hand lay-up technique. Initially, a study of the volumetric density of the laminate was made in order to verify its use in lightweight structures. Also were performed comparative studies on the mechanical properties and fracture modes under the conditions of the specimens without the central hole and with the different holes. For evaluating the possible influence of the holes in the structural stability of the laminate, the Residual Strength of the composite was determined for each case of variation in hole diameter. As a complementary study, analyses of the macroscopic final fracture characteristic of the laminates were developed. The presence of the central hole of any sizes, negatively changed the ultimate tensile strength. Regarding the elastic modulus, moreover, the difference found between the specimens was within the range of tests displacement, showing the laminate stability related to the stiffness

Obtenção e caracterização de um compósito de poliuretano de mamona e pó de vidro para aplicações em insolantes térmicos

Thermal insulation is used to protect the heated or cooled surfaces by the low thermal conductivity materials. The rigid ricin polyurethane foams (PURM) are used for thermal insulation and depend on the type and concentration of blowing agent. Obtaining PURM occurs by the use of polyol, silicone, catalyst and blowing agent are pre -mixed, reacting with the isocyanate. The glass is reusable, returnable and recyclable heat insulating material, whose time of heat dissipation determines the degree of relaxation of its structure; and viscosity determines the conditions for fusion, operating temperatures, annealing, etc. The production of PURM composites with waste glass powder (PV) represents economical and renewable actions of manufacturing of thermal insulating materials. Based on these aspects, the study aimed to produce and characterize the PURM composites with PV, whose the mass percentages were 5, 10, 20, 30, 40 and 50 wt%. PURM was obtained commercially, while the PV was recycled from the tailings of the stoning process of a glassmaking; when the refining process was applied to obtain micrometer particles. The PURM + PV composites were studied taking into account the standard sample of pure PURM and the influence of the percentage of PV in this PURM matrix. The results of the chemical, physical and morphological characterization were discussed taking into account the difference in the microstructural morphology of the PURM+PV composites and the pure PURM, as well the results of the physicochemical, mechanical e thermophysical tests by values obtained of density, hardness, compressive strength, specific heat, thermal conductivity and diffusivity. In general, the structure of pure PURM showed large, elongated and regular pores, while PURM+PV composites showed irregular, small and rounded pores with shapeless cells. This may have contributed to reducing their mechanical strength, especially for PURM - PV50. The hardness and density were found to have a proportional relationship with the PV content on PURM matrix. The specific heat, thermal diffusivity and thermal conductivity showed proportional relationship to each other. So, this has been realized that the increasing the PV content on PURM matrix resulted in the rise of diffusivity and thermal conductivity and the decrease of the specific heat. However, the values obtained by the PURM composites were similar the values of pure PURM, mainly the PURM-PV5 and PURM-PV10. Therefore, these composites can be applied like thermal insulator; furthermore, their use could reduce the production costs and to preserve the environment

Aspectos metodológicos para análise de depósitos de pulverizações pela determinação dos depósitos pontuais

Objetivou-se com este trabalho avaliar a variabilidade dos depósitos de traçadores, simulando herbicidas aplicados em pós-emergência, em populações de Brachiaria plantaginea e Commelina benghalensis infestantes da cultura da soja. Os depósitos dos traçadores foram também avaliados em plantas da cultura, utilizando-se o pulverizador de barra tratorizado, com pontas de jato plano da série 110-SF-03, aplicando o volume de 250 L ha-1 de calda preparada com 0,18% de corante Azul Brilhante e 0,18% de Amarelo Saturn Yellow. Os alvos naturais utilizados foram: plantas de soja com 150 repetições; B. plantaginea no estádio de duas a oito folhas, coletadas na linha da cultura com 141 repetições; e B. plantaginea e C. benghalensis nas entrelinhas, com 150 e 50 repetições, respectivamente. Os alvos artificiais foram constituídos por lâminas distribuídas a 0, 12,2 e 22,5 cm da linha da cultura. Após a aplicação, os alvos foram coletados individualmente e lavados com 30, 20 e 15 mL de água deionizada, para soja, lâminas e plantas daninhas, respectivamente. Estas originaram as amostras analisadas em espectrofotômetro, estimando-se o depósito de calda em µL por planta e µL cm² de área foliar. Foram ajustadas curvas de regressão entre os depósitos unitários e as freqüências acumuladas, utilizando-se o modelo de Gompertz. As relações entre os depósitos máximos e mínimos foram de 7, 4, 10 e 6 para soja, C. benghalensis e B. plantaginea na linha e na entrelinha, respectivamente. As plantas de B. plantaginea da entrelinha receberam, em média, 34% a mais de depósito do que as plantas da linha.

Microemulsões aplicadas ao tratamento de Óleos isolantes

Naphthenic lubricating oils are used in transformers with the purpose of promoting electrical insulation and dissipating heat. The working temperature range of these oils typically lies between 60°C and 90°C and their useful life is 40 years in average. In that temperature range, the oils are decomposed during operation, whereby a small fraction of polar compounds are formed. The presence of these compounds may induce failure and loss of physical, chemical and electrical properties of the oil, thus impairing the transformer operation. By removing these contaminants, one allows the oxidized insulating oil to be reused without damaging the equipment. In view of this, an investigation on the use of surfactants and microemulsions as extracting agents, and modified diatomite as adsorbent, has been proprosed in this work aiming to remove polar substances detected in oxidized transformer oils. The extraction was carried out by a simple-contact technique at room temperature. The system under examination was stirred for about 10 minutes, after which it was allowed to settle at 25°C until complete phase separation. In another experimental approach, adsorption equilibrium data were obtained by using a batch system operating at temperatures of 60, 80 and 100°C. Analytical techniques involving determination of the Total Acidity Number (TAN) and infrared spectrophotometry have been employed when monitoring the decomposition and recovery processes of the oils. The acquired results indicated that the microemulsion extraction system comprising Triton® X114 as surfactant proved to be more effective in removing polar compounds, with a decrease in TAN index from 0.19 to 0.01 mg KOH/g, which is consistent with the limits established for new transformer oils (maximal TAN = 0.03 mg KOH/g). In the adsorption studies, the best adsorption capacity values were as high as 0.1606 meq.g/g during conventional adsoprtion procedures using natural bauxite, and as high as 0.016 meq.g/g for the system diatomite/Tensiofix® 8426. Comparatively in this case, a negative effect could be observed on the adsorption phenomenon due to microemulsion impregnation on the surface of the diatomite

Análise farmacognóstica e atividade antibacteriana de extratos vegetais empregados em formulação para a higiene bucal

A utilização de extratos vegetais vem se tornando uma alternativa importante para a prevenção de doenças periodontais. Este trabalho objetivou desenvolver uma formulação de enxagüatório bucal, contendo, em associação, extratos hidroalcoólicos de Rosmarinus officinalis, Plantago major, Tabebuia impetiginosa, Achillea millefollium e Nasturtium officinale; avaliar sua composição farmacognóstica e sua atividade antibacteriana, como também da fórmula proposta. Foram realizados estudos de pré-formulação e análises farmacognósticas para as espécies vegetais. A atividade antibacteriana in vitro foi observada por meio dos métodos de difusão em disco de papel, por hole- plate e por template, frente a Staphylococcus aureus, Bacillus subtilis, Escherichia colik, Enterococcus faecalis e Pseudomonas aeruginosa. A concentração inibitória mínima (CIM) foi determinada por meio do método de macrodiluições sucessivas em caldo. Os resultados obtidos apresentaram-se de acordo com o histórico farmacognóstico das drogas estudadas. Todas as bactérias foram inibidas pelos extratos, observando-se que as espécies S. aureus e B. subtilis mostraram, aparentemente, maior sensibilidade. A CIM variou, em relação a sensibilidade de cada espécie bacteriana estudada, de 312,5 µL/mL a 1250 µL/mL para os extratos vegetais e de 625 µL/mL a 2500 µL/mL para o enxaguatório bucal. São necessários estudos complementares para a confirmação da eficácia deste produto e sua utilização na prevenção de doenças periodontais.

Cytotoxicity study of some Ti alloys used as biomaterial

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Avaliação clínica da relação entre o índice de placa, índice gengival, alinhamento dental, mucosa ceratinizada, tipo de periodonto e distúrbios oclusais com a ocorrência de recessão gengival

This study clinically evaluated the relationship of gingival recessions with the periodontal index of gingival and plaque, dental alignment, keratinized mocous, type of periodontal, and occlusal disorders. Study participants were individuals aged between 19 and 33 years. The evaluations were performed by using questionnaires and clinical examinations. In subjects examined, the teeth were assessed and divided into groups (Molars, premolars, canines and incisors). The gingival recession were measured in the central region of the teeth and individuals were subject to disclosure to the plate and observing the poll of plaque and gingival index, respectively. 558 teeth were examined, with 24.1%, 135 had gingival recession greater than or equal to 1mm. Through the combination of tests used to evaluate the average of the recession and its relationship with the variables studied, we observed that the degree of recession of the elements assessed dental showed, almost for the most part, when higher values associated with the index plaque (p = 0.101), Gingival Index (p = 0.053), dental alignment (p = 0.962), width of keratinized mocous (p = 0.004) and type of periodontium (p = 0.033), however statistically significant difference could only be considered when related the recessions in the keratinized mocous and the type of the periodontium. Although we identify, when we evaluate the whole set of teeth that occlusal disturbances (p = 0.002) were more strongly associated with cases of gum recession that the gingival index (p = 0.006), however, these two conditions were correlated with the cases of recession, contributing to its occurrence

A metallurgical study of aluminium alloys used as aircraft components

The effects of heat treatment on morphologies and microstructures of Al 2024 and Al 7050 alloys, used as aircraft components, were studied by metallographic techniques. Light microscopy (LM) and quantitative image analysis were used to characterize the precipitate dispersion and morphology for these alloys. The application of the scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) combined techniques for studying these multiphase systems makes it possible to distinguish and quantify the different phases in the surface structure. Xray diffraction also permitted a qualitative comparison of the structures before and after heat treatments.

Efeitos do ultra-som terapêutico sobre o crescimento longitudinal do fêmur e da tíbia em ratos

Objectives: To determine the effects of ultrasound therapy on the femur and tibia growth in young rats. Method: Four-week-old male Ratus Norvegicus totaling 115 animals, divided into four groups, were submitted to ultrasound therapy (0.8 MHz, fixed tube head, continuous pulse, for 10 minutes, once a day, ten times) on the medial face of the right knee, with powers of 0.0 W/cm2 (group 31), 0.5 W/cm2 (group G2), 1.0 W/cm2 (group G3), and 1.5 W/cm2 (group G4). Histological slides of the epiphysis, growth plate and metaphysis and the femoral and tibial length measurements were studied in the sixth, thirteenth and twenty-sixth weeks of life. The data were submitted to factorial analysis of variance according to a one-way layout. Results: No statistically significant bone growth alteration was established between any of the three treated groups and the control group. However, alterations in femoral and tibial growth suggesting a decrease in G4 in relation to 02 and G3 were noted. In G4, histopathological alterations, such as cellular necrosis and post-necrosis bone neoformation were found. Conclusion: According to this study, no statistical evidence of bone growth stimulus or inhibition resulting from the application of ultrasound therapy was found when comparing the treated groups with the control group. Histological alterations regarded as pathological were only observed in G4. Also, smaller significant bone growth was found in G4 compared to G2 and G3. Level of Evidence: Level II, cross-sectional study.

Desempenho e características de carcaça de bezerros confinados recebendo dietas com diferentes degradabilidades da fração protéica

O objetivo deste trabalho foi avaliar as respostas do fornecimento de dietas com diferentes níveis de proteína degradável no rúmen (PDR), durante a fase inicial de confinamento, no desempenho, nas características de crescimento monitoradas in vivo por ultra-sonografia e nos parâmetros de carcaça e qualidade de carne de bovinos jovens. Foram utilizados 60 bezerros Brangus não castrados, com 8 meses e peso vivo médio de 243,2 kg, submetidos a três tratamentos nas fases de crescimento (Fase 1) e terminação (Fase 2): T1 - 69% PDR nas Fases 1 e 2; T2 - 77% PDR na Fase 1 e 69% PDR na Fase 2; T3 - 61% PDR na Fase 1 e 69% PDR na Fase 2. Na Fase 1, os animais do tratamento T2 apresentaram menor ganho de peso médio diário que os animais do tratamento T1 e pior conversão alimentar que T1 e T3. O peso de carcaça quente, seu rendimento e os pesos de dianteiro, ponta de agulha e traseiro, bem como a área de olho de lombo, gordura subcutânea, força de cisalhamento e composição química da carne, não apresentaram diferença estatística entre tratamentos. A utilização de dietas com menor teor de PDR melhorou a conversão alimentar e o ganho de peso médio diário em até 11,5 e 16,9%, respectivamente, na fase de crescimento, indicando a utilização de menores níveis de PDR neste período.

Implantes de resina de poliuretana vegetal (Ricinus communis) na tração linear, fixação e fusão vertebral no cão: estudo experimental

Placa e espaçador de polímero derivado do óleo de mamona (PDOM) (Ricinus communis) foram avaliados clínica, radiográfica e histologicamente na tração linear, fixação e fusão vertebral cervical em 20 cães adultos, sem raça definida, pesando entre 17 e 22kg. Foram sacrificados quatro animais aos 10, 30, 60, 90 e 120 dias de pós-operatório. Após exposição da coluna cervical, por acesso ventral, o disco intervertebral de C4-C5 foi fenestrado e a abordagem ao canal medular foi feita por meio de fenda óssea. Um espaçador de PDOM foi colocado preenchendo o defeito ósseo. Os corpos vertebrais C4-C5 foram fixados com placa do mesmo material, utilizando-se dois parafusos corticais em cada corpo vertebral. Apenas um animal apresentou déficit neurológico no pós-operatório imediato. Radiograficamente as vértebras mostravam-se normais e alinhadas, sem colapso do espaço intervertebral, porém não houve neoformação óssea entre as vértebras. Ao exame mielográfico, não houve compressão da medula espinhal. Os implantes foram efetivos em manter a tração linear e fixação das vértebras cervicais e não ocorreu a fusão vertebral.