基底对光学薄膜弱吸收测量的影响

对表面热透镜技术测量光学薄膜弱吸收低频调制时不同基底对测量的影响进行了理论分析。用Lambda-900分光光度计测量了K9和石英基底的Ti3O5单层膜的吸收值，将该组样品作为定标片；用表面热透镜装置分别测量了BK7和石英空白基底及HfO2，ZnO两组不同基底不同厚度单层膜样品的吸收。通过分析比较同一工艺条件下镀制的不同基底薄膜样品用与其同种和不同种基底定标片定标测量的结果，表明在低频测量时需要用与测量样品同种基底的定标片定标；不同厚度样品的测量结果表明，在不能严格满足热薄条件时，测量结果需引入修正值。

离子束辅助反应制备的氧化铪薄膜特性

采用电子束直接蒸发氧化铪、无辅助电子束反应蒸发和离子束辅助反应蒸发金属铪3种沉积方式制备了单层HfO2薄膜,对样品的光学性能、结构特性以及激光损伤特性进行了研究。实验结果表明:通过反应沉积的方法可以有效减少缺陷产生并改善均匀性,施加离子辅助可以提高薄膜的折射率,在一定条件下还可以有效地降低吸收,但激光损伤阈值仍未达到直接采用氧化铪制备的水平;晶体结构方面,离子辅助条件下可以获得单斜相氧化铪薄膜,并且随着轰击能量的提高由(002)面的择优取向向(-111)面转变。

真空室内金属杂质污染对光学薄膜性能的影响

真空室内金属粒子污染是降低激光薄膜性能的一个重要因素。采用高真空残余气体分析仪,对薄膜沉积过程中的气氛进行分析。发现由黄铜制作的加热灯架在工作时会分解出Zn,在这种条件下沉积薄膜,会使薄膜中掺入金属杂质,导致薄膜激光破坏阈值降低。采用表面分析技术对薄膜的组分进行分析,证实薄膜中锌杂质的存在。激光破坏实验证明,含有锌杂质的薄膜的破坏阈值明显降低。

Influence of oxygen plasma treatment on properties of ZrO2 films prepared by e-beam evaporation techniques

Zirconia films were prepared by e-beam evaporation, and oxygen plasma treatment was used to modify film properties. Spectrophotometry, x-ray diffractometry (XRD), and atomic force microscopy were used to characterize refractive index, extinction coefficient, rnicrostructure, and surface roughness, respectively. The experimental results indicate that both refractive index and extinction coefficient of the films were reduced slightly after oxygen plasma treatment, with the decrease of intrinsic stress and surface roughness. From XRD spectra, the intensity decrease of the T(110) diffraction peak was clearly observed after the treatment, which was caused by the restructuring of the film atoms. (C) 2008 Elsevier Ltd. All rights reserved.

倾斜沉积制备雕塑薄膜的研究进展

倾斜沉积是一种新型的薄膜沉积技术。通过制备过程中基片的旋转和倾斜,可以制备出斜柱状、之字形、螺旋状、S形以及C形等各种形状的雕塑薄膜。雕塑薄膜可以实现许多传统薄膜无法实现的光学性质,为光学薄膜的设计与制备开辟了新的途径。本文综述了雕塑薄膜的制备方法,分析了雕塑薄膜的结构特征及影响因素,并阐述了其在光学领域的广泛应用前景。

SiO_2薄膜折射率的准确拟合分析

精确的光学常数对于设计和制备高品质的光学薄膜非常重要,尤其是那些光学性能对折射率变化敏感的薄膜。SiO_2是一种常用的低折射率材料,因与常用基底折射率相近使其准确拟合有一定难度。实验通过离子束溅射制备了SiO_2单层膜。考虑测量时的误差和基底折射率的影响,采用透射率包络和反射率包络得到了SiO_2的折射率,并用所得折射率进行反演来对这两种途径在实际测量拟合过程中的准确性进行比对。分析表明,剩余反射率在实际的测量过程中误差更小,直接用测量镀膜前后基片的剩余反射率值可以更简便更准确地得到SiO_2的折射率,能达到10~(-2)的精度。

Mechanism initiated by nanoabsorber for UV nanosecond-pulse-driven damage of dielectric coatings

A model of plasma formation induced by UV nanosecond pulselaser interaction with SiO2 thin film based on nanoabsorber is proposed. The model considers the temperature dependence of band gap. The numerical results show that during the process of nanosecond pulsed-laser interaction with SiO2 thin film, foreign inclusion which absorbs a fraction of incident radiation heats the surrounding host material through heat conduction causing the decrease of the band gap and consequently, the transformation of the initial transparent matrix into an absorptive medium around the inclusion, thus facilitates optical damage. Qualitative comparison with experiments is also provided. (C) 2008 Optical Society of America.

吸收杂质热辐射诱导光学薄膜破坏的热力机制

光学元件的破坏是限制高功率激光系统发展的主要问题,理解光学元件的破坏机制对于高功率激光系统的设计、运行参量选择以及器件技术发展有重要影响。以热辐射模型为基础研究了杂质吸收诱导光学薄膜破坏的热力过程。研究发现薄膜发生初始破坏所需时间很短,脉冲的大部分时间是引起薄膜发生更大的破坏。在考虑吸收杂质发生相变的情况下,计算了吸收杂质汽化对薄膜产生的蒸汽压力,论证了薄膜发生宏观破坏的可能性。此模型能很好地解释光学薄膜的平底坑破坏形貌。

Nanostructuring of materials for device and sensor applications

The recent developments in nanotechnology are reviewed, with particular emphasis on its application in microsystem technology where increased reliability is achieved by integrating the sensor and the readout electronics on the same substrate. New applications may be possible using integrated micromechanical clips to connect optic fibers and components in integrated silicon systems. Some of the key developments in enabling technologies are also described, including the control of thin film deposition, nanostructuring to tailor the properties of thin film, silicon micromachining to make sensors, and microclips for the low-cost assembly of integrated optical microsystems.

Red-Green-Blue 2D tuneable liquid crystal laser devices

In this paper, we review our recent experimental work on coherent and blue phase liquid crystal lasers.We will present results on thin-film photonic band edge lasing devices using dye-doped low molar mass liquid crystals in self-organised chiral nematic and blue phases. We show that high Q-factor lasers can be achieved in these materials and demonstrate that a single mode output with a very narrow line width can be readily achievable in well-aligned mono-domain samples. Further, we have found that the performance of the laser, i.e. the slope efficiency and the excitation threshold, are dependent upon the physical parameters of the low molar mass chiral nematic liquid crystals. Specifically, slope efficiencies greater than 60% could be achieved depending upon the materials used and the device geometry employed. We will discuss the important parameters of the liquid crystal host/dye guest materials and device configuration that are needed to achieve such high slope efficiencies. Further we demonstrate how the wavelength of the laser can be tuned using an in-plane electric field in a direction perpendicular to the helix axis via a flexoelectric mechanism as well as thermally using thermochromic effects. We will then briefly outline data on room temperature blue phase lasers and further show how liquid crystal/lenslet arrays have been used to demonstrate 2D laser emission of any desired wavelength. Finally, we present preliminary data on LED/incoherent pumping of RG liquid crystal lasers leading to a continuous wave output. © 2009 SPIE.

Deposition and characterisation of ultralow-stress ZnO thin films for application in FBAR-based gravimetric biosensors

Zinc oxide (ZnO) thin films were deposited at high rates ( > 50 nm min-1) using a unique technique known as high target utilisation sputtering (HiTUS). The films obtained possess good crystallographic orientation, low surface roughness, very low stress and excellent piezoelectric properties. We have utilised the films to develop highly sensitive biosensors based on thickness longitudinal mode (TLM) thin film bulk acoustic resonators (FBARs). The FBARs have the fundamental TLM at a frequency near 1.5 GHz and quality factor Q higher than 1,000, which is one of the largest values ever reported for ZnO-based FBARs. Bovine Serum Albumin (BSA) solutions with different concentrations were placed on the top of different sets of identical FBARs and their responses to mass-loading from physically adsorbed protein coatings were investigated. These resonators demonstrated a high sensitivity and thus have a great potential as gravimetric sensors for biomedical applications. © 2011 Inderscience Enterprises Ltd.

Gated three-terminal device architecture to eliminate persistent photoconductivity in oxide semiconductor photosensor arrays

The composition of amorphous oxide semiconductors, which are well known for their optical transparency, can be tailored to enhance their absorption and induce photoconductivity for irradiation with green, and shorter wavelength light. In principle, amorphous oxide semiconductor-based thin-film photoconductors could hence be applied as photosensors. However, their photoconductivity persists for hours after illumination has been removed, which severely degrades the response time and the frame rate of oxide-based sensor arrays. We have solved the problem of persistent photoconductivity (PPC) by developing a gated amorphous oxide semiconductor photo thin-film transistor (photo-TFT) that can provide direct control over the position of the Fermi level in the active layer. Applying a short-duration (10 ns) voltage pulse to these devices induces electron accumulation and accelerates their recombination with ionized oxygen vacancy sites, which are thought to cause PPC. We have integrated these photo-TFTs in a transparent active-matrix photosensor array that can be operated at high frame rates and that has potential applications in contact-free interactive displays. © 2012 Macmillan Publishers Limited. All rights reserved.

Superconducting fault current limiter design using parallel-connected YBCO thin films

Superconducting Fault Current Limiters (SFCLs) are able to reduce fault currents to an acceptable value, reducing potential mechanical and thermal damage to power system apparatus and allowing more flexibility in power system design and operation. The device can also help avoid replacing circuit breakers whose capacity has been exceeded. Due to limitations in current YBCO thin film manufacturing processes, it is not easy to obtain one large thin film that satisfies the specifications for high voltage and large current applications. The combination of standardized thin films has merit to reduce costs and maintain device quality, and it is necessary to connect these thin films in different series and parallel configurations in order to meet these specifications. In this paper, the design of a resistive type SFCL using parallel-connected YBCO thin films is discussed, including the role of a parallel resistor and the influence of individual thin film characteristics, based on both theory and experimental results. © 2009 IEEE.

Experimental study on an SFCL using series-connected YBCO thin films

Superconducting Fault Current Limiters (SFCLs) are able to reduce fault currents to an acceptable value, reducing potential mechanical and thermal damage and allowing more flexibility in an electric power system's design. Due to limitations in current YBCO thin film manufacturing techniques, it is necessary to connect a number of thin films in different series and parallel configurations in order to realise a practical SFCL for electric power system applications. The amount of resistance generated (i.e. the degree of current limitation), the characteristics of the S-N transition, and the time at which they operate is different depending on their comparative characteristics. However, it is desirable for series-connected thin films to have an operating time difference as small as possible to avoid placing an excess burden on certain thin films. The role of a parallel resistance, along with the influence of thin film characteristics, such as critical current (Ic), are discussed in regards to the design of SFCLs using YBCO thin films. © 2008 IOP Publishing Ltd.

Nucleation, growth, and control of ferroelectric-ferroelastic domains in thin polycrystalline films

The unique response of ferroic materials to external excitations facilitates them for diverse technologies, such as nonvolatile memory devices. The primary driving force behind this response is encoded in domain switching. In bulk ferroics, domains switch in a two-step process: nucleation and growth. For ferroelectrics, this can be explained by the Kolmogorov-Avrami-Ishibashi (KAI) model. Nevertheless, it is unclear whether domains remain correlated in finite geometries, as required by the KAI model. Moreover, although ferroelastic domains exist in many ferroelectrics, experimental limitations have hindered the study of their switching mechanisms. This uncertainty limits our understanding of domain switching and controllability, preventing thin-film and polycrystalline ferroelectrics from reaching their full technological potential. Here we used piezoresponse force microscopy to study the switching mechanisms of ferroelectric-ferroelastic domains in thin polycrystalline Pb 0.7Zr0.3TiO3 films at the nanometer scale. We have found that switched biferroic domains can nucleate at multiple sites with a coherence length that may span several grains, and that nucleators merge to form mesoscale domains, in a manner consistent with that expected from the KAI model. © 2012 American Physical Society.