白腐菌选择性降解木质素的研究

对15株白腐真菌进行了以玉米秸秆为基质的初步筛选，从中获得一株选择性系数较高的菌株Y10，并对其降解玉米秸秆的情况进行了研究。结果表明，在30天的培养过程中菌株Y10对玉米秸秆降解的选择性系数都大于1，第15天选择性系数最高为3.88。对未经降解和降解过的玉米秸秆分别作了紫外光谱和红外光谱分析，结果表明，经该菌降解后玉米秸秆的化学成分发生了很大变化，且木质素的降解程度要大于纤维素的降解程度。对菌株Y10进行了ITS-5.8S rDNA序列鉴定，初步判定其为Cerrena sp.。 为了考查不同的外源添加物对菌株Y10降解玉米秸秆的影响，在以玉米秸秆为基质的固态发酵培养基中分别添加了7种金属离子、8种碳源、6种氮源。结果显示，这7种金属离子均能促进木质素的降解，并且一定浓度的某些离子明显抑制纤维素的降解；其中添加0.036%的MnSO4·H2O和0.36%的MgSO4·7H2O对纤维素降解的抑制作用比较强，降解率分别为0.96%和1.31%，木质素的选择性系数分别达到了34.40和20.17。8种碳源中除麦芽糖外都能促进木质素的降解，除微晶纤维素外都明显促进纤维素的降解。6种氮源中酒石酸铵、硫酸铵、草酸铵和氯化铵的添加都会使该菌生长变慢，而且氮源浓度越高菌丝生长越慢。外加碳源和金属离子对半纤维素降解和选择性系数的影响不大。 同时对菌株Y10在液态培养下产木质素降解酶的条件和培养基做了优化。结果表明，在初始产酶培养基中，菌株Y10的漆酶酶活在第10d达到最高，锰过氧化物酶酶活在第11d达到最高，基本上检测不到木质素过氧化物酶。菌株Y10产漆酶的最适温度为32℃，最适PH为6.0；产锰过氧化物酶的最适温度为32℃，最适PH为6.5。菌株Y10产漆酶的最佳碳源为甘露糖，最佳氮源为酒石酸铵，最适诱导剂VA浓度为3 mmol/L，最适表面活性剂TW-80浓度为1%。 利用响应面法对其产漆酶的培养基进行优化，优化后的培养基配方为葡萄糖10.00 g/L，酒石酸铵0.50 g/L，大量元素296.50 ml/L，微量元素100.00 ml/L，NTA 1.40 g/L，VA 5.00 mmol/L，吐温-80加入量为0.10%。进行了菌株Y10产漆酶的验证实验，实测酶活为5282.56 U/L，与预测酶活5162.73 U/L接近。在优化后培养基中，菌株Y10在第14 d达到生长的最高峰，第20 d时，漆酶酶活最高，为11325.00 U/L；第16 d时，锰过氧化物酶酶活最高，为30.77 U/L。 对菌株Y10的漆酶酶学性质做了初步的研究，结果显示，酶反应的最适温度为40℃-65℃，最适PH为3.0。在40℃，PH=3.0时，漆酶催化ABTS反应的米氏方程为 。 Fifteen white-rot fungi based on corn stalk were screened. One white-rot fungus Y10 with high selectivity value was obtained. The degradation of corn stalk was initially studied. The results indicated that the selectivity value was above 1 during the 30 day-cultivation and the highest was 3.88 after 15 days. The composition of untreated and treated stalk was analyzed through ultraviolet spectroscopy and infrared spectroscopy. It was found that the composition of treated stalk was greatly altered and the degree of the degradation of lignin is greater than the cellulose. Y10 was identified as Cerrena sp. by ITS -5.8S rDNA sequence analysis. The influence of metal ions, carbon sources and nitrogen sources on corn stalk degradation by white-rot fungus was studied. While all seven metal ions could promote lignin degradation, the cellulose degradation was best inhibited at certain ion concentrations. Notably, when 0.036% MnSO4·H2O and 0.36% MgSO4·7H2O were added into the medium, the cellulose degradation was restrained to the extents that the coefficients of lignin selectivity rose to 34.40 and 20.17 respectively. It was also found that all carbon sources except maltose can promote lignin degradation. The addition of carbon sources other than microcrystalline cellulose significantly promoted cellulose degradation. The addition of the nitrogen sources, ammonium tartrate, ammonium sulfate, oxalate, ammonium chloride, resulted in remarkable inhibition to mycelium growth; the larger the concentrations of nitrogen sources are, the slower the mycelium grew. The addition of carbon sources and metal ions had less impact on the degradation of hemicellulose and selectivity value. Meanwhile, we optimized the conditions and culture medium of the lignin-degrading enzyme production of strain Y10. The results showed that in the initial culture medium, the Lac activity was highest at the 10th day, the MnP activity was highest at the 11th day and the LiP could not be detected. The optimum condition of Lac was at temperature 32 and PH =6.0 and the optimum condition of MnP was at temperature 32 and PH =6.5. The optimum carbon source for Lac was seminose, the optimum nitrogen source was ammonium tartrate, the optimum content of VA was 3 mmol/L, the optimum content of TW-80 was 1%. PB and RSM were used to optimize the culture medium of laccase by white-rot fungus Y10. The optimum culture medium was consist of glucose 10.00 g/L, ammonium tartrate 0.50 g/L, macro elements 296.50 ml/L, trace elements 100.00 ml/L, NTA 1.40 g/L, VA 5.00 mmol/L, TW-80 0.10%. Under the optimal conditions, the activity of laccase was 5282.56 U/L and the experimental value agreed with the predicted value 5162.73 U/L. The biomass was highest at the 14th day, the Lac activity was highest at the 20th day, the MnP activity was highest at the 16th day. The results of the studies on the characteristics of Lac showed that the optimum temperature for Lac activity is 40℃-65℃ ; the optimum PH for Lac activity is 3.0 and under 40℃，PH=3.0, the Michaelis-menten equation of Lac catalized ABTS oxidation was .

溶藻菌群对铜绿微囊藻的溶藻效应及其作用机理研究

水华暴发是一个世界性的问题，近年来在发展中国家显得尤其严重。水华暴发给环境和公众健康带来巨大灾难，一些蓝藻产生的毒素可以造成鱼类、鸟禽和家畜的死亡，而臭名昭著的微囊藻产生的微囊藻毒素更是有强烈致癌效应。因此，寻找控制水华藻类的有效方法非常迫切。在利用物理和化学方法处理不甚理想的情况下，利用溶藻细菌控藻成为一个新的研究方向。溶藻细菌一般直接从富营养化水体中分离，杀藻活力对有害蓝藻具有较强的选择性而不危害其它生物，尤其适合在水华发生初期使用，可以在短时间内达到阻止藻类增殖的效果。本研究富集分离到一个高效溶解铜绿微囊藻的溶藻菌群，对其溶藻效应和溶藻机制进行了探索研究。 1溶藻菌群的富集筛选及其溶微囊藻效果 富集筛选得到一个有明显抑藻效果的菌群，它对铜绿微囊藻有显著溶藻效果。与对照组相比，加入富集的溶藻菌后，第4 d开始出现溶藻现象，6~8 d出现明显的溶藻效果，8 d后测得叶绿素去除率在85%以上。 2 溶藻菌群的作用范围及溶藻特性 富集分离到的溶藻菌群对铜绿微囊藻和念珠藻有显著溶藻作用，对水华微囊藻和其它几株受试微囊藻没有明显溶藻效应。该溶藻菌群不仅可以在液体中溶解铜绿微囊藻，生长在固体平板上的藻苔也有一定的溶藻效应，生成溶藻空斑。保证快速溶藻的最大稀释度可以达到1/100, 000。 3 环境因子对菌群溶藻效力的影响 试验发现，不同的pH、温度、和光照条件下，溶藻菌群溶藻效力明显不同，且不同种类的氮源对其溶藻作用也有一定影响。这些条件对该菌群溶藻作用的影响，在相当的程度上可能取决于它们对藻和细菌两者的生长状况的影响综合。 4 溶藻菌群的溶藻作用机理 溶藻菌液过滤除菌和煮沸灭菌处理后溶藻液，未见明显的溶藻效果，只有原液具有很好的溶藻效果。因此可初步确定，蓝藻细胞的溶解可能是由溶藻菌直接接触藻细胞产生的作用效果。显微镜观察发现，细菌在溶藻的过程中频繁地接触藻细胞并侵入藻细胞，破坏进而裂解杀死藻细胞。这也进一步说明了此溶藻菌是通过直接方式杀藻。 5 溶藻菌群的菌群结构解析 分离有溶藻效果的纯菌的多次尝试都没有成功。结合DGGE和16S rDNA文库综合分析发现：Rubritepida菌，假单胞菌和鞘氨醇单胞菌是存在于铜绿微囊藻中的三种伴生细菌。加入富集的溶藻菌群后，菌群结构发生明显的变化，Rubritepida菌、假单胞菌消失，混合菌群则包含未培养黄杆菌，鞘氨醇单胞菌和噬氢菌，其中黄杆菌是优势菌群，并且细菌种群结构的变化与藻细胞消亡之间有显著的相关性。通过菌种的分离鉴定与DGGE和16S rDNA文库的测序结果比较，一些未培养菌可能在溶藻过程中起重要调控作用。 6 溶藻细菌控藻应用基础 (1) 扩大规模的模拟水华实验进一步确定了细菌对微囊藻的强烈溶解作用。 (2) 铜绿微囊藻(Microcystis aeruginosa 905, zc)、微囊藻(Microcystis spp., zd)和溶藻菌群共培养试验表明，zc可以抑制zd生长，而溶藻菌群可以溶zc。 本研究是第一次报道混合菌群的溶藻效应。该溶藻菌群对带有藻际细菌的铜绿微囊藻具有高效的溶藻效力，表明它对自然界中存在的带菌铜绿微囊藻和其它一些蓝藻的生消具有一定的控制作用。对进一步研究菌藻关系与生态学作用，以及对富营养化湖泊和水库水体中蓝藻暴发的防控，该菌群具有一定的应用潜力。 Cyanobacterial blooms break out frequently all over the world, especially in developing countries. Blooms create enormous disasters to public health and to the environment. Some cyanobacterial blooms produce extremely toxic substances that have killed fish, domestic animals and birds. It has been well known that microcystins, a hepatoxin produced by Microcystis, can promote tumors in humans. So it is very important to find an effective method for controlling the growth of the bloom-forming algae. Measures for controlling such kind of algae include physical, chemic and biologic means, but the former two may damage the aquatic environment and require high-energy inputs. The alternative approach for the elimination of nuisance algae involves the application of algicidal bacteria. The algicidal bacteria, which are nontoxic to other organisms and most of which are isolated from the eutrophic lake in situ, may be potential microbial algaecides. In the initial stages of the water blooms, they are able to restrain the biomass or multiplication of the bloom-forming algae in a short time. In order to use algicidal bacteria to suppress blooms of M. aeruginosa, we isolated a bacterial culture capable of lysing the noxious cyanobacteria M. aeruginosa. In this paper we described some properties of the bacterial culture and its growth-inhibiting or algicidal effects on the growth of M. aeruginosa, and investigated its algicidal mechanisms. 1 Enrichment of a microbial culture that lyses Microcystis aeruginosa A mixed bacterial culture was isolated from a hypereutrophic pond and showed significant algicidal activity against the noxious Microcystis aeruginosa. Algae lysis would be seen obviously 4 days later when the algae culture was killed and became yellow contrast to no-addition controls, and chlorophyll a (chl-a) reduction went beyond 85% 8 days later. 2 The host range and some other algicidal feature of the mixed algicidal culture. Microcystis aeruginosa, Nostoc sp., were susceptible to the mixed algicidal culture, while the lytic effects of this mixed culture on Microcystis flos-aquae and some other tested Microcystis were feeble.The algicidal culture can not only lyse M. aeruginosa in liquid media, but aslo lyse M. aeruginosa lawns on soft agar plates and form plaques. The maximun dilution of the mixed culture required for rapid Microcystis lysis is 1/100, 000. 3 Influences of environmental factors such as pH, temperature, illumination, and the nitrogen source on the lytic activity of the mixed bacterial culture on Microcystis aeruginosa. In our investigations, it was shown that the lytic activity of the mixed bacterial culture on Microcystis aeruginosa was straightly correlated with pH, temperature, illumination, as well as the nitrogen source in the medium. The impacts of these environmental factors on the algicidal activity of the mixed bacterial culture, to a certain extent, may depend on both the algal and the bacterial growth rates under the tested environmental conditions. 4 The mechanisms of algal cell lysis by the algicidal bacteria Death was detected when the mixed bacterial culture was added to the algal culture, but not when only the culture filtrate or autoclaved bacterial culture was added. This indicates that the mixed bacterial culture did not release extracellular products inhibitory to Microcystis aeruginosa. In addition, under the microscope, we observed frequent contacts btween bacteria and algae cells, and some bacteria can even penetrate into target algal cells and destroyed them. These results may suggest that the bacterium kill the alga by direct contact. 5 Molecular Characterization of the algicidal bacterial culture Attempts for isolation of pure bacterium or bacteria from the enrichment culture responsible for Microcystis lysis have so far been failed. Based on PCR-DGGE (denaturing gradient gel electrophoresis) and 16S rDNA clone library analysis, Rubritepida sp., Pseudomonas sp. and Sphingomonas sp., as accompanying bacteria, were existed in M. aeruginosa. The bacterial community in M. aeruginosa showed significant change after adding the enrichment culture, where uncultured Flavorbacterium sp., Sphingomonas sp. and Hydrogenophaga sp. were observed, and the uncultured Flavorbacterium sp. became a dominant species. The obvious correlation can be seen between change of bacterial population and extinction of M. aeruginosa. Compared identification of pure bacterium with sequencing of DGGE bands and the clone distribution of the clone libraries, it was inferred that some uncultured bacteria were probably play an important role in controlling the growth and abundance of M. aeruginosa. This report is the first example of a mixed bacterial culture with the ability to lyse M. aeruginosa. 6 Further study for algae control by applications of algicidal bacteria (1) Algae lysis would be seen obviously 6 days later when the algae culture was killed and became yellow contrast to no-addition controls, and chlorophyll a (chl-a) was reducted to a low level 20 days later in the simulated water bloom experiments. (2) The growth of Microcystis sp. (zd) was restrained by Microcystis aeruginosa 905 (zc) when they were co-cultured together, and zc was lysed by the algicidal bacterial culture. This report is the first example of a mixed bacterial culture with the ability to lyse M. aeruginosa, and its algicidal activity remained high against non-axenic tested M. aeruginosa, suggesting that bacteria in the natural environment could play a role in controlling the growth and abundance of M. aeruginosa and other cyanobacteria. Such bacteria could also potentially be used as agents to prevent the mass development of cyanobacteria in eutrophic lakes and reservoirs.

亚硝化—厌氧氨氧化处理猪场废水研究

猪场废水COD浓度高、氨氮浓度高、悬浮物浓度高，已成为农村面源污染的主要来源，并严重威胁到农村饮用水安全。猪场废水氨氮浓度高、处理难度大，如何采用经济高效的方法，去除氨氮使其达到排放标准，一直是猪场废水处理中面临的重要难题。 厌氧氨氧化是近年受到国内外水处理研究者广泛关注的新型生物脱氮技术，具有不需要外加有机碳源、节省供氧量、降低能耗等优点。虽然国内外研究者对厌氧氨氧化过程的脱氮机理、厌氧氨氧化菌的生理生化特性等进行了多方面的研究，但已有的报道大多以模拟废水为研究对象，以猪场废水为研究对象的报道，在国内外文献中极少有报导。 本论文以猪场废水为主要研究对象，考察了猪场废水的亚硝化过程、厌氧氨氧化的启动过程，并对亚硝化和厌氧氨氧化联合用于猪场废水脱氮进行了探索。 1．论文首先研究了猪场废水的亚硝化过程，考察了废水水质和主要运行条件对亚硝化过程的影响。实验表明：（1）亚硝化阶段反应时间为8到10h时，出水中氨氮和亚硝酸盐浓度比可达到1：1～1：1.23，满足厌氧氨氧化反应对二者比例的要求；达到前述要求时，氨氮去除率达到58.3～65.6 %，亚硝化率在整个过程均保持在97 %以上，COD去除率在59.2～68.6 %；（2）曝气量（溶解氧）对亚硝化过程影响显著，随着曝气量增大，达到厌氧氨氧化要求的氨氮与亚硝酸盐氮浓度比例所需水力停留时间τ越短，pH出现明显下降的时间越短；（3）τ对应的pH在7.8～8.1之间，无需进行pH调节即可满足厌氧氨氧化反应对pH的要求；（4）氨氮和COD降解过程遵循一级反应动力学，氨氮和COD降解的速率常数分别为0.0656～0.0724 1/h和0.0491～0.0664 1/h。 2．在进行亚硝化过程研究的同时，以模拟废水为试验对象，进行厌氧氨氧化启动研究。以反硝化污泥和养殖厂储水池厌氧底泥的混合污泥作为接种污泥，历时大约100天，培育出具有厌氧氨氧化活性的污泥，氨氮和亚硝酸盐氮最高进水浓度分别为223.8 mg/L和171.4 mg/L，去除率最高分别达48%和41.5%，此时二者消耗比例为1.33：1。 3．在猪场废水的亚硝化研究完成和厌氧氨氧化过程初步启动成功后，在模拟废水中逐步加入猪场废水的亚硝化处理出水，逐步实现亚硝化和厌氧氨氧化的组合。亚硝化出水添加到厌氧反应器后，厌氧氨氧化反应仍可继续进行，且去除效率逐步提高。研究发现添加的亚硝化出水中携带的亚硝化细菌在厌氧氨氧化菌膜外层生长并累积，增加了厌氧氨氧化反应基质的传质阻力，妨碍了厌氧氨氧化效率的提高。 4．亚硝化－厌氧氨氧化实际工程应用探索中，生物接触氧化池可在有效去除废水中的有机物的同时实现亚硝化，出水中氨氮和亚硝酸盐比例平均为1.10，可满足后续厌氧氨氧化的要求；在适宜的进水浓度和温度下，ABR池出现了厌氧氨氧化启动的迹象；研究同时发现，水质的波动和气温的变化是工程中影响厌氧氨氧化菌活性的重要因素。 论文的主要创新点在于：（1）以猪场废水为研究对象，以实现厌氧氨氧化为目标，对亚硝化过程进行了比较详细的考察，获得了亚硝化出水满足厌氧氨氧化要求的工艺条件，通过对其COD和氨氮降解过程的考察，得出亚硝化阶段COD降解和氨氮去除的动力学模型；（2）对亚硝化－厌氧氨氧化处理猪场废水进行了探索，确立了影响其污染物去除率稳定的重要因素。 论文的上述研究成果，为厌氧氨氧化技术的实用性研究提供理论依据。 Piggery wastewater, which is characterized by high concentration of COD、ammonium and suspend substance, has become a most important source of non-point source pollution and also severely threats drinking water security in rural area. How to discharge piggery wastewater with the ammonium concentration meeting standard by economical and effective method? This is the most urgent problem in piggery wastewater treatment. As a new biological nitrogen removal technology, Anammox process has been paid more and more attention by researchers all over the world. Anammox has advantages of no need of organic carbon addition, low oxygen consumption and energy consumption. Plenty of investigations have been carried out to the mechanism, physiological and biochemical characteristic of bacteria about Anammox. Most of researches focused on synthetic wastewater, there is rare report about its application in piggery wastewater. In this paper，experimental studies were performed to investigate Sharon process in treatment of piggery wastewater，the start up process of Annammox using synthetic wastewater were studied, the feasibility of applying Sharon-Anammox process in the nitrogen removal of piggery wastewater was evaluated. 1. Sharon process of piggery wastewater was firstly investigated to analyze the effects of water quality and main running parameters, which meet the NH4+-N to NO2--N ratio requirement of successive Anammox. Results showed: (1)During Sharon Process，after 8～10 hours’ reaction the NH4+-N to NO2--N ratio in effluent reached 1:1.0～1:1.23, when the removal percentage of NH4+-N was 58.3～65.6 %, a semi-nitration rate of above 97 % was achieved during the process; meanwhile 59.2～68.6 % of the COD was also removed. (2)The aeration rate（oxygen） had obvious effect on the hydraulic retention time(τ) which met the NH4+-N to NO2--N ratio requirement of Anammox. As aeration rate increased, the hydraulic retention time(τ) was shortened. (3) The pH corresponding to τ was between 7.8 and 8.1, thus it needed no artificial adjustment. (4) The reduction of ammonia and COD followed the first-order reaction kinetics. The velocity constants of ammonia and COD were 0.0656～0.0724 1/h and 0.0491～0.0664 1/h, respectively. 2. The startup of Anammox process using the artificial wastewater was performed simultaneously with Sharon. The aim was to investigate the running parameters of Anammox and make foundation for the combination stage. By using the mixture of denitrifying sludge and anaerobic sludge in tank of the breeding factory, sludge of Anammox activity was cultivated in UASB after 100 days. The removal percentage of NH4+-N and NO2-N were up to 48% and 41.5%, respectively, when the NH4+-N and NO2-N influent concentration were 223.8 mg/L and 171.4 mg/L, respectively, the NH4+-N and NO2-N removal rate was 1.33:1. 3. After investigation of Sharon and startup of Anammox, effluent of Sharon process was added into the synthetic wastewater to combine Sharon and Anammox step by step. It took some time after the addition of Sharon effluent that Anammox reaction continued and the removal rate kept increasing. It indicated that nitrifying bacteria were carried by the Sharon effluent cumulated in the outer layer of Anammox. This enhanced transfer resistance of Anammox reaction and the increasing removal rate was restrained. 4. In the bio-contact oxidation pond of practical project, Sharon process were carried out successfully and organic compounds were removed effectively. An average NO2-N/ NH4+-N rate of 1:1.0 was achieved in the effluent, which met the requirement of successive Anammox. Under condition of suitable influent concentration and temperature, there was evidence that Anammox could start up in ABR. The variety of wastewater and temperature had great affects on Anammox activity in practical engineering. Innovation of this paper: (1) The Sharon process for treating piggery wastewater was discussed in details. Technological parameters that met requirement of Anammox were obtained. The dynamic models of COD and ammonium removal in the process were educed. (2) Sharon-Ananmmox for treatment of piggery wastewater was investigated, and the primary influencing factors was studied. This paper could be a theoretical consult for research of Anammox utility.

厌氧好氧一体化生物反应器处理发酵废水的中试研究

一体化反应器由于投资少、占地小、管理运行方便等优点而备受青睐。但现有的一体化反应器大都适用于处理中低浓度废水，耐受负荷普遍偏低。本课题研制出新型高效的厌氧好氧一体化生物反应器，旨在通过反应器结构优化、高效微生物载体研制、配合高效微生物菌剂技术处理中高浓度有机废水，实现高效和低耗，降低设备造价，提高反应器运行稳定性。 首先开展了菌剂对废水的适配试验。采用15种不同的微生物菌剂，以葡萄糖配水、中药提取废水、啤酒废水、氨氮配水为基质，分别测定了微生物菌剂的耗氧速率和厌氧比产甲烷速率，以其为指标比较了各菌剂对废水的适配性。根据结果选择活性高的14＃、8＃、10＃菌剂，在试验室进行了菌剂对废水的连续处理试验，取得良好的处理效果，为菌剂在厌氧好氧一体化生物反应器的小试、中试中的应用奠定了基础。 经小试研究后，又对厌氧好氧一体化生物反应器进行了处理发酵废水的中试研究。试验结果表明，反应器启动快，系统有机负荷2.72 kgCODm-3d-1时整个反应器去除率保持在84.5％～93.19％，在30多天内一次启动成功。冲击负荷试验中，系统总有机负荷最高可达到8.88 kgCODm-3d-1，系统去除率稳定在88.10％～96.88%，说明反应器处理效率高，抗冲击能力强。稳定运行期间，COD去除率可达90％以上，各项指标都能达到国家排放标准。 此外，对反应器配套系统高效菌剂、高分子复合颗粒载体进行了研究。结果显示，菌剂与反应器适配良好，各功能区形成了丰富、高活性的微生物，厌氧区颗粒污泥TS高达83.9 gL-1，VS/TS为56.9％～57.4％，比产甲烷活性为280～350 mLCH4 gvss-1d-1；好氧区固定化微生物TS高达1.921 gL-1，VS/TS为94.02～94.30％。对载体性能的研究表明，此高分子复合颗粒载体密度适中，易于流化，不易流失；粗糙多空，易于挂膜；且无生物毒害作用，稳定安全，是一种优良的生物载体。反应器各功能区对废水的降解过程分析，说明了反应器、菌剂、载体适配良好，在其协同作用下，实现了污染物的高效降解。 The integrated reactors were popular because of their characteristics such as little investment, small occupation of land, convenient of manage and running etc. But the present integrated reactors were mostly applied for treating wastewater of low concentration, the load tolerance was generally on the low side. A new type integrated anaerobic-aerobic bio-reactor was developed, which was conducted to treating organic wastewater of middle or high concentration by optimization of reactor structure, development of efficient microbe carrier and adaptation of high active microbial blends, to achieve high efficiency and low consume, reduce equipment cost, enhance running stabilization of reactor. The adaptability test of microbial blends on different wastewater was carried on firstly. Oxygen consumption rate and anaerobic specific activity of methane producing of 15 different microbial blends were measured separately taking glucose artificial wastewater, Chinese herb extracting wastewater, brewery wastewater and ammonia nitrogen artificial wastewater as substrate, by which the adaptabilities of different microbial blends to wastewater were compared. According to the results high active microbial blends 14#, 8# and 10# were selected and used in the continuous treatment of wastewater in the laboratory and had obtained good effect, which had laid a foundation for application microbial blends to small scale test and pilot test of integrated anaerobic-aerobic bio-reactor. After the small scale test, the pilot test of the integrated anaerobic-aerobic bio-reactor treating fermentation wastewater was carried on. The test results showed fast initiation of the reactor. When system organic load reached 2.72 kgCODm-3d-1the COD removal rate of the reactor was stable between 84.5%～93.19% and it initiated successfully in more than 30 days at a time. In the load shock test the maximum organic load of system could reach to 8.88 kgCODm-3d-1 and the COD removal rate could be stable between 88.10%~96.88% which indicated that the reactor was efficient for treating wastewater and had strong resistance to shock load. At stable running period the COD removal rate of the reactor was over 90% and each index of wastewater could reach to the national discharge standards. In addition, the high active microbial blends and the macromolecule compound granule carrier, the matching system of the reactor was studied. It showed that the microbial blends adapted well to the reactor and abundant and high active microbes were formed in each functional field. The TS of granule sludge in anaerobic field was as high as 83.9 gL-1, the VS/TS was 56.9%~57.4%, the specific activity of methane producing was 280~350 mLCH4 gvss-1d-1. And the TS of immobilized biological granule was as high as 1.921 gL-1, the VS/TS was 94.02%~94.30%. Study on the carrier showed that the self-made macromolecular compound granule carrier was moderate of density, easy of fluidization, unease of running off, rough and porous, easy of films fixation, no bio-toxic, stable and safe, was a kind of superior carrier. Analysis of degradation process in each functional field confirmed the reactor, microbial blends and carriers were in good adaptation and wastewater was decontaminated by their cooperation.

Computational study on the addition of HCN to methanimine catalyzed by formamidine and formamide

In this paper, we have carried out a theoretical study on the addition of HCN to methanimine with formamidine or formamide using second-order Moller-Plesset perturbation (MP2) method with 6-31 + G(d,p) basis sets. At MP2 level. a high-energy, intermediate has been located for each pathway. The addition of HCN to methanimine with formamidine has the lowest free energy barrier according to the calculations at MP2 level. (C) 2004 Elsevier B.V. All rights reserved.

不同N素形态对落叶松苗木根/土界面pH值及养分有效性的影响

The effect of different nitrogen and phosphorus sources on pH and the availability of mineral nutrients in the root/soil interface of Larix gmelinii seedlings were studied by means of root-mat method. The results showed that the addition of NH~+_4-N decreased the pH in the root/soil interface, while the addition of NO~-_3-N increased the pH in contrast with the control treatment. The sort of the P sources and the distance from the root plane remarkably influenced the changes of pH in the root/soil interface induced by the addition of the nitrogen sources. Compared with the addition of only NH~+_4-N, the extent to which the pH in the root/soil interface decreased was obviously smaller when treated by NH~+_4-N and rock P. When treated with different P sources, the contents of available P in the root/soil interface were affected by the sort of the N sources. When treated with soluble P, the contents of the available P in the root/soil interface obviously increased for the addition of both NH~+_4-N and NO~-_3-N. When treated with rock P, the contents of the available P increased only in the area 0～3 mm from the root plane for NH~+_4-N, whereas the contents of available P in the root/soil interface changed little for NO~-_3-N. The results above showed that the protons excreted by the roots were the main driving force for the solution of the rock P in the root/soil interface. The availability of Fe in the root/soil interface increased as a result of acidity induced by the NH~+_4-N, whereas the availability of Fe in the root/soil interface decreased because of the pH increase induced by the NO_3~-_N. The effect of different N sources on the availability of Fe in the root/soil interface was also affected by the sort of P sources. The concentrations of P、Fe in the leaves remarkably differed when treated by different N、P sources and concentrations of the P、Fe in the root/soil interface were correlated to those in the leaves of the seedlings.

The effects of CO2 addition on the partial oxidation of heptane for hydrogen generation

The effects of CO2 on the partial oxidation of heptane for hydrogen generation have been studied. Based on the experimental results and thermodynamic equilibrium calculations, the validity of CO2 addition to weaken the hot spots, and the feasibility of the autothermal operation are discussed.

Concise synthesis of novel practical sulfamide-amine alcohols for the enantioselective addition of diethylzinc to aldehydes

Novel sulfamide-amine alcohol ligands were designed using a grafting strategy and synthesized from readily available starting materials via a simple, efficient method. The key features of these ligands for the asymmetric addition of diethylzinc to aldehydes included stability, enhanced effectiveness without using Ti((OPr)-Pr-i)(4), suitability for a variety of aldehydes, the ability to operate at room temperature, and selectability to afford either absolute configuration products with enantiomeric excess up to >99%.