Efficient extreme UV harmonics generated from picosecond laser pulse interactions with solid targets

The generation of high harmonics created during the interaction of a 2.5 ps, 1053 nm laser pulse with a solid target has been recorded for intensities up to 10(19) W cm(-2). Harmonic orders up to the 68th at 15.5 nm in first order have been observed with indications up to the 75th at 14.0 nm in second-order diffraction. No differences in harmonic emission between s and p polarization of the laser beam were observed. The power of the 38th high harmonic at 27.7 nm is estimated to be 24 MW.

Role of charge in the radioprotection of E. coli by thiols.

The role of net charge (Z) of thiols in their ability to radioprotect cells has been investigated in a glutathione (GSH)-deficient strain of E. coli. This strain, 7, is deficient in the enzyme gamma-glutamylcysteine synthetase and allows the effects of added low molecular weight thiols to be studied. Using the gas explosion system it is possible to measure the chemical repair of the free-radical precursors of lethal lesions by thiols in intact cells. The first-order chemical repair rate in strain 7 is 280s(-1) in comparison with 1100s(-1) in the wild-type strain 1157. From the measured difference in the intracellular concentration of GSH between the wild-type and the mutant, this gives a second-order repair rate, k(r)'s of 1.23 +/- 0.3 X 10(5) dm(3)mol(-1)s(-1). Measurement of intracellular thiol levels after addition of various low molecular weight thiols showed that uptake was rapid, leading to stable thiol levels within 1 min. The ratios of the intracellular to extracellular concentrations (C-in/C-out) were 0.74 for 3-mercaptopropionic acid (Z=-1), 0.56 for 2-mercaptoethanol (Z=0), 1.47 for cysteamine (Z=+1) and 1.04 for WR1065 (Z=+2). The k(r)'s for these thiols were 1.3 +/- 0.5 X 10(5) dm(3)mol(-1)s(-1) for 30-mercaptopropionic acid, 3.3 +/- 1.6 x 10(5) dm(3)mol(-1)s(-1) for 2-mercaptoethanol, 3.9 +/- 1.1 X 10(5) dm(3)mol(-1)s(-1) for cysteamine and 2.7 +/- 1.1 X 10(6) dm(3)mol(-1)s(-1) for WR1065. These are lower and increase less with charge than previously published values for chemical repair in isolated pBR322 DNA, probably because of the association of nucleoproteins and polyamines with the cellular DNA of E. coli. However, the approximate three-fold increase in k(r) per unit increase in Z shows that the counter-ion condensation and co-ion depletion are important in determining the effectiveness of charged thiols in the radioprotection of E. coli.

Further evidence for double-strand breaks originating from a paired radical precursor from studies of oxygen fixation processes

By using a fast reaction technique which employs H2S gas as a fast-reacting chemical repair agent, it is possible to measure the competition kinetics between chemical repair reactions and oxygen fixation reactions in model DNA and cellular systems. In plasmid pBR322 DNA irradiated with electrons, we have compared the oxygen fixation reactions of the free radical precursors that lead to the production of single-strand (SSBs) and double-strand breaks (DSBs). For the oxygen-dependent fixation of radical damage leading to SSBs, a second-order rate constant of 2.3 x 10(8) dm(3) mol(-1) s(-1) was obtained compared to 8.9 x 10(7) dm(3) mol(-1) s(-1) for DSBs. The difference is in general agreement with predictions from a multiple-radical model where the precursor of a DSB originates from two radicals. The fixation of this precursor by oxygen will require both radicals to be fixed for the DSB to be formed, which will have slower kinetics than that of single free-radical precursors of SSBs. (C) 1999 by Radiation Research Society.

Improved conjugate gradient implementation for least squares support vector machines

As a promising method for pattern recognition and function estimation, least squares support vector machines (LS-SVM) express the training in terms of solving a linear system instead of a quadratic programming problem as for conventional support vector machines (SVM). In this paper, by using the information provided by the equality constraint, we transform the minimization problem with a single equality constraint in LS-SVM into an unconstrained minimization problem, then propose reduced formulations for LS-SVM. By introducing this transformation, the times of using conjugate gradient (CG) method, which is a greatly time-consuming step in obtaining the numerical solution, are reduced to one instead of two as proposed by Suykens et al. (1999). The comparison on computational speed of our method with the CG method proposed by Suykens et al. and the first order and second order SMO methods on several benchmark data sets shows a reduction of training time by up to 44%. (C) 2011 Elsevier B.V. All rights reserved.

A New Gradient Descent Approach for Local Learning of Fuzzy Neural Models

The majority of reported learning methods for Takagi-Sugeno-Kang fuzzy neural models to date mainly focus on the improvement of their accuracy. However, one of the key design requirements in building an interpretable fuzzy model is that each obtained rule consequent must match well with the system local behaviour when all the rules are aggregated to produce the overall system output. This is one of the distinctive characteristics from black-box models such as neural networks. Therefore, how to find a desirable set of fuzzy partitions and, hence, to identify the corresponding consequent models which can be directly explained in terms of system behaviour presents a critical step in fuzzy neural modelling. In this paper, a new learning approach considering both nonlinear parameters in the rule premises and linear parameters in the rule consequents is proposed. Unlike the conventional two-stage optimization procedure widely practised in the field where the two sets of parameters are optimized separately, the consequent parameters are transformed into a dependent set on the premise parameters, thereby enabling the introduction of a new integrated gradient descent learning approach. A new Jacobian matrix is thus proposed and efficiently computed to achieve a more accurate approximation of the cost function by using the second-order Levenberg-Marquardt optimization method. Several other interpretability issues about the fuzzy neural model are also discussed and integrated into this new learning approach. Numerical examples are presented to illustrate the resultant structure of the fuzzy neural models and the effectiveness of the proposed new algorithm, and compared with the results from some well-known methods.

THE SYNTHESIS, KINETIC CHARACTERIZATION AND APPLICATION OF A NOVEL BIOTINYLATED AFFINITY LABEL FOR CATHEPSIN-B

In this study we report on the synthesis, kinetic characterization and application of a novel biotinylated and active-site-directed inactivator of cathepsin B. Thus the peptidyliazomethane biotinyl-Phe-Ala-diazomethane has been synthesized by a combination of solid-phase and solution methodologies and has been shown to be a very efficient inactivator of bovine and human cathepsin B. The respective apparent second-order rate constants (k0bs./[I]) for the inactivation of the human and bovine enzymes by this reagent, namely approximately 5.4 x 10(4) M-1 and approximately 7.8 x 10(4) M-1, compare very favourably with those values determined for the urethane-protected analogue benzloxycarbonyl-Phe-Ala-chloromethane first described by Green & Shaw [(1981) J.Biol. Chem. 256, 1923-1928], thus demonstrating that the presence of the biotin moiety at the P3 position is compatible with inhibitor effectiveness. The utilization of this reagent for the detection of cathepsin B in electrophoretic gels, using Western blotting and in combination with a streptavidin/alkaline phosphatase detection system, is also demonstrated. Given that the peptidydiazomethanes exhibit a pronounced reactivity towards cysteine proteinases, we feel that the present label may well constitute the archetypal example of a wide range of reagents for the selective labelling of this class of proteinase, even in a complex biological milieu containing additional classes of proteinases.

Direct Democracy and Regional Integration::Citizens' Perceptions of Treaty Implications and the Irish Reversal on Lisbon

Analyses of voting in European Union referendums typically distinguish between ‘second-order’ effects and the impact of substantive ‘issues’. In order to explain change in referendum outcome, two types of substantive issues are distinguished in this article. Focusing on Irish voting in the Lisbon Treaty referendums and using data from post-referendum surveys, it is found that perceptions of treaty implications outperform underlying attitudes to EU integration in predicting vote choice at both referendums, and perceptions of treaty implications are strong predictors of vote change between the referendums. The findings have broadly positive implications for normative assessments of the usefulness of direct democracy as a tool for legitimising regional integration advance.

Systolic building block for high performance recursive filtering

A novel bit level systolic array is presented that can be used as a building block in the construction of recursive digital filters. The circuit accepts bit-parallel input data, is pipelined at the bit level, and exhibits a very high throughput rate. The most important feature of the circuit is that it allows recursive operations to be implemented directly without incurring the large m cycle latency (where m is approximately the word length) normally associated with such systems. The use of this circuit in the construction of both first- and second-order IIR (infinite-impulse-response) filters is described.

Imprecise probabilistic query answering using measures of ignorance and degree of satisfaction

In conditional probabilistic logic programming, given a query, the two most common forms for answering the query are either a probability interval or a precise probability obtained by using the maximum entropy principle. The former can be noninformative (e.g.,interval [0; 1]) and the reliability of the latter is questionable when the priori knowledge isimprecise. To address this problem, in this paper, we propose some methods to quantitativelymeasure if a probability interval or a single probability is sufficient for answering a query. We first propose an approach to measuring the ignorance of a probabilistic logic program with respect to a query. The measure of ignorance (w.r.t. a query) reflects howreliable a precise probability for the query can be and a high value of ignorance suggests that a single probability is not suitable for the query. We then propose a method to measure the probability that the exact probability of a query falls in a given interval, e.g., a second order probability. We call it the degree of satisfaction. If the degree of satisfaction is highenough w.r.t. the query, then the given interval can be accepted as the answer to the query. We also prove our measures satisfy many properties and we use a case study to demonstrate the significance of the measures. © Springer Science+Business Media B.V. 2012

Stochastic particle acceleration in the lobes of giant radio galaxies

We investigate the acceleration of particles by Alfven waves via the second-order Fermi process in the lobes of giant radio galaxies. Such sites are candidates for the accelerators of ultra-high-energy cosmic rays (UHECR). We focus on the nearby Fanaroff-Riley type I radio galaxy Centaurus A. This is motivated by the coincidence of its position with the arrival direction of several of the highest energy Auger events. The conditions necessary for consistency with the acceleration time-scales predicted by quasi-linear theory are reviewed. Test particle calculations are performed in fields which guarantee electric fields with no component parallel to the local magnetic field. The results of quasi-linear theory are, to an order of magnitude, found to be accurate at low turbulence levels for non-relativistic Alfven waves and at both low and high turbulence levels in the mildly relativistic case. We conclude that for pure stochastic acceleration via Alfven waves to be plausible as the generator of UHECR in Cen A, the baryon number density would need to be several orders of magnitude below currently held upper limits.

Non-Markovian qubit dynamics induced by Coulomb crystals

We investigate the backflow of information in a system with a second-order structural phase transition, namely, a quasi-one-dimensional Coulomb crystal. Using standard Ramsey interferometry which couples a target ion (the system) to the rest of the chain (a phononic environment), we study the non-Markovian character of the resulting open system dynamics. We study two different time scales and show that the backflow of information pinpoints both the phase transition and different dynamical features of the chain as it approaches criticality. We also establish an exact link between the backflow of information and the Ramsey fringe visibility.

Anisotropy parameters in two-color two-photon above-threshold ionization

We employ the time-dependent R-matrix (TDRM) method to calculate anisotropy parameters for positive and negative sidebands of selected harmonics generated by two-color two-photon above-threshold ionization of argon. We consider odd harmonics of an 800-nm field ranging from the 13th to 19th harmonic, overlapped by a fundamental 800-nm IR field. The anisotropy parameters obtained using the TDRM method are compared with those obtained using a second-order perturbation theory with a model potential approach and a soft photon approximation approach. Where available, a comparison is also made to published experimental results. All three theoretical approaches provide similar values for anisotropy parameters. The TDRM approach obtains values that are closest to published experimental values. At high photon energies, the differences between each of the theoretical methods become less significant.

Hexavalent Chromium Adsorption by a Novel Activated Carbon Prepared by Microwave Activation

Microwave heating reduces the preparation time and improves the adsorption quality of activated carbon. In this study, activated carbon was prepared by impregnation of palm kernel fiber with phosphoric acid followed by microwave activation. Three different types of activated carbon were prepared, having high surface areas of 872 m2 g-1, 1256 m2 g-1, and 952 m2 g-1 and pore volumes of 0.598 cc g-1, 1.010 cc g-1, and 0.778 cc g-1, respectively. The combined effects of the different process parameters, such as the initial adsorbate concentration, pH, and temperature, on adsorption efficiency were explored with the help of Box-Behnken design for response surface methodology (RSM). The adsorption rate could be expressed by a polynomial equation as the function of the independent variables. The hexavalent chromium adsorption rate was found to be 19.1 mg g-1 at the optimized conditions of the process parameters, i.e., initial concentration of 60 mg L-1, pH of 3, and operating temperature of 50 oC. Adsorption of Cr(VI) by the prepared activated carbon was spontaneous and followed second-order kinetics. The adsorption mechanism can be described by the Freundlich Isotherm model. The prepared activated carbon has demonstrated comparable performance to other available activated carbons for the adsorption of Cr(VI).

Multimode entanglement and telecloning in a noisy environment

We address the generation, propagation, and application of multipartite continuous variable entanglement in a noisy environment. In particular, we focus our attention on the multimode entangled states achievable by second-order nonlinear crystals-i.e., coherent states of the SU(m,1) group-which provide a generalization of the twin-beam state of a bipartite system. The full inseparability in the ideal case is shown, whereas thresholds for separability are given for the tripartite case in the presence of noise. We find that entanglement of tripartite states is robust against thermal noise, both in the generation process and during propagation. We then consider coherent states of SU(m,1) as a resource for multipartite distribution of quantum information and analyze a specific protocol for telecloning, proving its optimality in the case of symmetric cloning of pure Gaussian states. We show that the proposed protocol also provides the first example of a completely asymmetric 1 -> m telecloning and derive explicitly the optimal relation among the different fidelities of the m clones. The effect of noise in the various stages of the protocol is taken into account, and the fidelities of the clones are analytically obtained as a function of the noise parameters. In turn, this permits the optimization of the telecloning protocol, including its adaptive modifications to the noisy environment. In the optimized scheme the clones' fidelity remains maximal even in the presence of losses (in the absence of thermal noise), for propagation times that diverge as the number of modes increases. In the optimization procedure the prominent role played by the location of the entanglement source is analyzed in details. Our results indicate that, when only losses are present, telecloning is a more effective way to distribute quantum information than direct transmission followed by local cloning.

Taguchi optimisation approach for production of activated carbon from phosphoric acid impregnated palm kernel shell by microwave heating

Taguchi method was applied to investigate the optimal operating conditions in the preparation of activated carbon using palm kernel shell with quadruple control factors: irradiation time, microwave power, concentration of phosphoric acid as impregnation substance and impregnation ratio between acid and palm kernel shell. The best combination of the control factors as obtained by applying Taguchi method was microwave power of 800 W, irradiation time of 17 min, impregnation ratio of 2, and acid concentration of 85%. The noise factor (particle size of raw material) was considered in a separate outer array, which had no effect on the quality of the activated carbon as confirmed by t-test. Activated carbon prepared at optimum combination of control factors had high BET surface area of 1,473.55 m² g-1 and high porosity. The adsorption equilibrium and kinetic data can satisfactorily be described by the Langmuir isotherm and a pseudo-second-order kinetic model, respectively. The maximum adsorbing capacity suggested by the Langmuir model was 1000 mg g-1.