984 resultados para W(100)
Resumo:
对爆源近区地下混凝土管道结构在爆炸冲击载荷作用下的动力学响应开展探索性实验研究。选用钢筋混凝土管道模拟地下结构,尺寸为:$\phi_{\hbox{内}}$800mm$\times$2000mm$\times$100mm。通过实验研究定量确定爆炸振动波载荷对地下结构产生的振动效应;定性确定爆炸冲击波载荷对地下管道结构和混凝土材料产生的动态破坏效应。爆炸当量分别为50 g和100 g TNT,爆炸距离取为0.1,0.3,1,7和10m。实验主要涉及地下管道结构在小药量爆炸点近区的破坏效应与爆炸药量和爆炸距离间关系的确定;混凝土材料破坏行为与药量和爆炸距离关系的确定;爆炸冲击波的影响范围以及爆炸振动波的有效影响范围与爆源特性的关系及爆炸响应函数的确定。从小当量地下结构爆炸实验观察到:地下结构的爆炸振动响应,即振动波波长和频率不同于土介质地表的波长和频率。与地表面上建筑物的波长和频率相比,振动波长持续作用时间明显缩短,且振动频率显著提高。这与地下结构的爆炸动力学响应,特别是爆源近距离的结构动力学响应存在着本质的区别。不同的爆炸距离和当量,地下爆炸对地下结构可以产生振动和冲击两种不同特征的动力学效应。在折算距离大于0.22$\sim$0.25 m/W$^{1/3}$时,100 g TNT当量的爆炸以产生振动效应为主。在折算距离小于0.22$\sim$0.25 m/W$^{1/3}$时,爆炸主要产生冲击效应;在爆炸距离小于1.5m/W$^{1/3}$时,地下爆炸振动波对结构产生的动力学响应的明显特征是管道结构发生径向变形。而且,管道上与爆源最近点是管道变形的对称点。管道的轴向和环向动力响应表现为相应方向上的刚体振动。在爆炸距离大于1.5 m/W$^{1/3}$,如等于2.15m/W1/3的情况下,爆炸振动波对管道结构产生的动力学响应主要表现为整体振动。结构的变形特征基本消失;地下爆炸冲击波载荷对爆源近区管道结构和混凝土材料可以产生三种破坏效应:在折算距离等于0.065 m/W$^{1/3}$时,低强度的冲击波载荷仅产生结构破坏效应。实验中观察到混凝土管道只沿其轴线方向上形成贯穿性裂纹,管道内外表面均无损伤和破碎现象;当折算距离等于0.027 m/W1/3时,较强冲击波载荷既引起管道的结构破坏,也产生混凝土材料的破坏。这时观察到沿混凝土管道轴线方向上,以及与轴线成30$^\circ$至50$^\circ$范围内形成贯穿性裂纹。同时在管道内表面出现直径约为210 mm的层裂区,最大层裂厚度约为8$\sim$12 mm;当折算距离等于0.022 m/W$^{1/3}$时,爆炸强冲击波载荷主要引起的混凝土材料破坏形式表现为破碎。即在管道上以爆源最近点为中心形成直径约为370 mm的贯穿性孔洞,还观察到该孔洞周边不同方向上有长度为230$\sim$410 mm不等的数条细裂纹形成。
Resumo:
本文对不同菌种(酵母菌和运动发酵单胞菌)快速生产燃料乙醇的条件进行了研究,实现了鲜甘薯快速转化为燃料乙醇。全文分为两部分: 第一部分:酵母菌快速生产燃料乙醇的条件研究。通过单因素试验,酵母菌快速生产燃料乙醇的条件为:发酵方式采用边糖化边发酵(SSF),蒸煮温度为85 ℃,料水比2:1(初始糖浓度 210 g/kg),糖化酶用量0.75 AGU/g 鲜甘薯,接种量10%(v/w)。在最优条件下,经过24 h发酵,乙醇浓度可达97.44 g/kg, 发酵效率为92%,发酵强度为4.06 g/kg/h。由于采用了低温蒸煮和SSF,可以大大节约能耗,从而降低乙醇生产的成本。同时,利用摇瓶优化的条件,进行了10 L,100 L,500 L发酵罐的放大试验,由于发酵罐初期可以人为通氧,使菌体能迅速积累,发酵时间缩短2 h,发酵效率在90%以上。 第二部分:运动发酵单胞菌快速生产燃料乙醇条件研究。通过单因素试验和正交试验获得了发酵的最佳参数:初始pH值6.0-7.0,硫酸铵5.0 g/kg,糖化酶量1.6 AUG/kg淀粉,初始糖浓度200 g/kg,接种量12.5%(v/w)。经过21 h发酵,乙醇浓度为95.15 g/kg,发酵效率可达94%。同时对不灭菌发酵也进行了研究,发酵效率可达92%。为鲜甘薯运动发酵单胞菌燃料乙醇的工业化生产打下基础。 对发酵结束后的残糖进行了研究。通过薄层层析和葡萄氧化酶测定证明:无论是酵母菌还是运动发酵单胞菌发酵结束后的发酵液中都不含葡萄糖。经过HPLC进一步分析残糖说明:发酵液中已没有葡萄糖成分;经糖化酶水解后仍没有葡萄糖出现;但经酸水解后又出现了葡萄糖,说明结束后的残糖是一些低聚糖结构。有关残糖的结构需要进一步研究。可以通过开发高效的低聚糖水解酶来降低发酵液的残糖,提高原料的利用率。 A new technology for rapid production fuel ethanol from fresh sweet potato by different microorganisms (Saccharomyces cerevisiae and Zymomonas mobilis) was gained in this research. The paper involved two parts: Part 1: The study on fuel ethanol rapid production from fresh sweet potato by Saccharomyces cerevisiae. The following parameters of Saccharomyces cerevisiae was investigated by a series of experiments: fermentation models, cooking temperature, initial sugar concentration and glucoamylase dosage. The results showed that SSF (simultaneous saccharification and fermentation) not only reduced the fermentation time (from 30 to 24h) but also enhanced the ethanol concentration (from 73.56 to 95.96 g/kg). With low-temperature-cooking (85 ℃) using SSF, the Saccharomyces cerevisiae was able to produce ethanol 97.44 g/kg which the fermentation yield could reach to 92% and ethanol productivity 4.06 g/kg/h from sweet potato enzymatic hydrolysis. Furthermore, the savings in energy by carrying out the cooking (85 ℃) and saccharification (30 ℃) step at low temperature had been realized. The results were also verified in 10 L, 100 L and 500 L fermentor. The fermentation yield was no less than 90%. The fermentation time of fermenter was shorter than Erlenmeyer flask. This may be that the aeration in the early fermentation period is available, which lead to the rapidly commutations of biomass. Part 2: The technology of ethanol rapid production with simultaneous saccharification and fermentation ( SSF ) by Zymomonas mobilis,using fresh sweet potato as raw material was studied. The effects of various factors on the yield of ethanol were investigated by the single factor and the orthogonal experiments. As a result, the optimal technical conditions were obtained from those experiments:initial pH value 6.0-7.0, nitride 5.0 g/kg,(NH4)2SO4, glucoamylase 1.6 AUG/kg starch, inoculums concentration 12.5% (v/w). The Zymomonas mobilis was able to produce ethanol 95.15 g/kg, with 94% of the theoretical yield, from fresh sweet potato after 24 h fermentation. The fermentation efficiency of non-sterilized was also reach to 92%. We also analyzed the final fermentation residual sugars of Saccharomyces cerevisiae and Zymomonas mobilis. When the residual sugars were analyzed by thin-layer chromatogram and glucose oxidase, there was no glucose. The analysis of reducing sugars by HPLC showed that there was no glucose existed in the fermentation liquor. However, the glucose appeared after being hydrolyzed by acid. It is indicated that the residual sugars in the final fermentation liquor were the configuration of oligosaccharide, which was linked by the special glycosidic bonds. It was feasible for reducing residual sugars to develope the enzyme that can degradation the oligosaccharide.
Resumo:
Abstract A state-of-the-art high energy heavy ion microbeam irradiation system is constructed at the Institute of Modern Physics of the Chinese Academy of Sciences. This microbeam system operates in both full current intensity mode and single ion mode. It delivers a predefined number of ions to preselected targets for research in biology and material science. The characteristic of this microbeam system is high energy and vertical irradiation. A quadrupole focusing system, in combination with a series of slits, has been designed to optimize the spatial resolution. A symmetrically achromatic system leads the beam downwards and serves simultaneously as an energy analyzer. A high gradient quadrupole triplet finally focuses a C6+ ion beam to 1 µm in the vacuum chamber within the energy range from 10 MeV/u to 100 MeV/u. In this paper, the IMP microbeam system is described in detail. A systematic investigation of the ion beam optics of this microbeam system is presented together with the associated aberrations. Comparison is made between the IMP microbeam system and the other existing systems to further discuss the performance of this microbeam. Then the optimized initial beam parameters are given for high resolution and high hitting efficiency. At last, the experiment platform is briefly introduced.
Resumo:
本文报道了He2+,O2+和Ne2+与W靶表面相互作用中的动能电子产额随离子入射速度变化的实验测量结果.结果表明:在本实验的入射速度范围内,对同一入射离子,动能电子产额随入射离子的速度增大而线性增加.基于动能电子发射的机理,我们分析了影响动能电子产额的因素,理论上得出动能电子产额与入射速度增长呈线性增加的关系,取得了实验上和理论上一致的结果.
Resumo:
用14.8 MeV中子同天然锇反应, 取道192O(n, α) 反应产生189W。通过放射化学分离流程, 从反应产物中分出W。用高纯Ge探测器完成放射性W样品γ射线单谱的测量。在189Re激发能级文献值的基础上并依据衰变和能级的关系以及189W衰变的γ射线能量和相对强度的实验数据, 给出了建议的189W衰变纲图。
Resumo:
给出了迄今为止实验中测得的新发现的189W的衰变数据——射线能量、半衰期和相对强度等,作为文献值;并将实验结果同文献值进行了比较。丰富了已测得的189W半衰期的文献值
Resumo:
Here we used cytokinesis-block micronucleus assay to measure the biological response along the penetrate depth of ions in water in human lymphocytes exposed to 100 MeV/u incident carbon ions in vitro. Polyethylene shielding was used to change the penetration depth of ions in water. A quantitative biological response curve was generated for micronuclei induction. The results showed a marked increase with the penetrate depth of ions in water in the micronuclei formation, which was consistent with a linearenergy- transfer dependent increase in biological effectiveness. The dose–response relationship for MN information was different at different penetrate depth of ions in water, at the 6 and 11.2 mm penetrate depth of ions in water, the dose–response relationships for the micronucleus frequencies induced by carbon ions irradiation were linear; while it was power function at 17.1 mm penetrate depth.
Resumo:
During the last years FOPI has developed a new ToF system as an upgrade of the existing detector based on Multi-strip Multi-gap Resistive Plate Chambers (MMRPCs). The intention is to increase the charged Kaon identification up to a laboratory momentum of 1 GeV/c and to enhance the azimuthal detector granularity. The new ToF barrel has an active area of 5 m(2) with 2400 individual strips (900 x 1.6 mm(2)) [A. Schuttauf, et al., Nucl. Phys. B 158 (2006) 52] which are read out on both sides by a custom designed electronics [M. Ciobanu, et al., IEEE Trans. Nucl. Sci. NS-54 (4) (2007) 1201; K. Koch, et al., IEEE Trans. Nucl. Sci. NS-52(3) (2005) 745]. To reach the envisaged goal a time resolution of 100 ps is needed, at a flight path of 1-1.3 m. Due to the rare production of the K- at SIS energies the efficiency of the MMRPCs has to be above 95%. We report on measurements with the detectors and electronics from the mass production line. For this purpose we used a proton beam at 2.0 and 1.25 GeV, at rates between 0.1 and 5 kHz/cm(2) to determine the timing, efficiency and rate capability of the MMRPCs
Resumo:
In collisions between slow F2+ ions (30 keV) and molecular targets, adenine, scattered particle production yields have been measured directly by simultaneous detection of neutrals, positive and negative ions. The relative cross-section for a negative ion formation channel was measured to be 1%. Despite a slight decrease compared to a larger target, the fullerene C-60, the measured negative ion formation cross section is still at least one order of magnitude larger than the yield in ion-atom interactions.
Resumo:
Here we prepare carbon nanotubes modified with ammonium persulfate, very short carbon nanotubes with 50-100 nanometer length was obtained, and the higher P potential of 52 mV was detected, these supporting the successful modification. HeLa cells were irradiated with P rays via adding or absent above functionalized carbon nanotubes (f- WCNTs) into cell culture medium with different concentration and radiation dosage. Confocal microscopy images and fluorescence-labeled DNA detection verified the successfully pure multi-walled carbon nanotubes (p-WCNTs) and f-WCNTs penetrated into cells. Compared with pure radiation, by MTT test, f-WCNTs induced cell death markedly with about 8.7 times higher than former one under little dose of radiation; meanwhile, no obvious toxicity was observed both in p-WCNTs and f-WCNTs without of radiation exposure. We hypothesized that large amount of hydroxyl and carbonyl organs on the surface of very short f-WCNTs changed into free radicals result from radiations led cell damage. These implied that f-WCNTs could be regarded as a new radiosensitizer.