A simulation study of the mixing, atomic flow and velocity profiles of crystalline materials during sliding

Self-contained Non-Equilibrium Molecular Dynamics (NEMD) simulations using Lennard-Jones potentials were performed to identify the origin and mechanisms of atomic scale interfacial behavior between sliding metals. The mixing sequence and velocity profiles were compared via MD simulations for three cases, viz.: sell-mated, similar and hard-softvcrystal pairs. The results showed shear instability, atomic scale mixing, and generation of eddies at the sliding interface. Vorticity at the interface suggests that atomic flow during sliding is similar to fluid flow under Kelvin-Helmholtz instability and this is supported by velocity profiles from the simulations. The initial step-function velocity profile spreads during sliding. However the velocity profile does not change much at later stages of the simulation and it eventually stops spreading. The steady state friction coefficient during simulation was monitored as a function of sliding velocity. Frictional behavior can be explained on the basis of plastic deformation and adiabatic effects. The mixing layer growth kinetics was also investigated.

In vitro detection and primary cultivation of bacteria producing materials inhibitory to ruminal methanogens.

A novel method for screening bacterial isolates for their potential to inhibit the growth of ruminal methanogenic Archaea was developed using a modification of the soft agar overlay technique, formally used for the isolation of lytic bacteriophages. This method may be used in the specific, hydrogen-rich conditions required for the growth of ruminal methanogenic Archaea.

Internal nitride formation during gas-phase thermal nitridation of titanium

Titanium nitride surface layers were prepared by gas-phase thermal nitridation of pure titanium in an ammonia atmosphere at 1373 K for different times. In addition to the surface nitride layer, nitride/hydride formation was observed in the bulk of the specimen. The cross-section of the specimen was characterized by various techniques such as optical microscopy, scanning electron microscopy, energy dispersive X-ray spectroscopy, secondary ion mass spectrometry and nanomechanical testing, and the mechanism of formation of these phases is discussed.

Thermoelectric Properties of Co4Sb12 Skutterudite Materials with Partial In Filling and Excess In Additions

The properties of Co4Sb12 with various In additions were studied. X-ray diffraction revealed the presence of the pure δ-phase of In0.16Co4Sb12, whereas impurity phases (γ-CoSb2 and InSb) appeared for x = 0.25, 0.40, 0.80, and 1.20. The homogeneity and morphology of the samples were observed by Seebeck microprobe and scanning electron microscopy, respectively. All the quenched ingots from which the studied samples were cut were inhomogeneous in the axial direction. The temperature dependence of the Seebeck coefficient (S), electrical conductivity (σ), and thermal conductivity (κ) was measured from room temperature up to 673 K. The Seebeck coefficient of all In-added Co4Sb12 materials was negative. When the filler concentration increases, the Seebeck coefficient decreases. The samples with In additions above the filling limit (x = 0.22) show an even lower Seebeck coefficient due to the formation of secondary phases: InSb and CoSb2. The temperature variation of the electrical conductivity is semiconductor-like. The thermal conductivity of all the samples decreases with temperature. The central region of the In0.4Co4Sb12 ingot shows the lowest thermal conductivity, probably due to the combined effect of (a) rattling due to maximum filling and (b) the presence of a small amount of fine-dispersed secondary phases at the grain boundaries. Thus, regardless of the non-single-phase morphology, a promising ZT (S 2 σT/κ) value of 0.96 at 673 K has been obtained with an In addition above the filling limit.

Estimation of Cavitation Erosion with Incubation Periods and Material Properties

A detailed study of the normalized correlations between the incubation period tc and the properties of various materials tested in a rotating disk device indicates that, at very high intensities, the strength properties influence the duration of tc. The analysis of extensive data from other laboratories for cavitation and liquid impingement erosion also indicates that, while both energy and strength properties influence the duration of tc, the latter ones predominate for a majority of cases. A fatigue-type failure occurs during tc. For estimating the time required to pierce a metallic specimen in a rotating device a relationship tp = 160 tc0.44 is proposed. A detailed study of normalized correlations between erosion resistance (inverse of erosion rate) and tc values of different materials tested in the rotating disk shows that correlations are good. Analysis of data from eight other investigators clearly points out the validity and the usefulness of this type of prediction.

New approach to improved detection and tracking performance in track-while-scan radars. Part 3: Performance prediction, optimisation and testing

The paper presents, in three parts, a new approach to improve the detection and tracking performance of a track-while-scan radar. Part 1 presents a review of the current status of the subject. Part 2 details the new approach. It shows how a priori information provided by the tracker can be used to improve detection. It also presents a new multitarget tracking algorithm. In the present Part, analytical derivations are presented for assessing, a priori, the performance of the TWS radar system. True track initiation, false track initiation, true track continuation and false track deletion characteristics have been studied. It indicates how the various thresholds can be chosen by the designer to optimise performance. Simulation results are also presented.

Kasvilajien tunnistaminen, oppiminen ja opettaminen yleissivistävän koulutuksen näkökulmasta

The purpose of the research was to determine how well Finnish pupils and students of different ages recognize plant species, which variables explain recognition of plant species, what plants and nature mean to the subjects and how plant species identification should be taught in general education in Finland. The subjects were pupils from: every class level of the primary schools (grades 1 6); lower- secondary school (grades 7 9); high school (grades I II); university departments of teacher education and classroom teachers and teachers from university involved with environmental teaching and also experts from education and botany. A total of 883 people took part in the research. Both quantitative and qualitative research methods were used. The quantitative methods were: a) plant species recognition test, where 70 plant species photos were shown to subjects and b) an experiment in which three experimental groups had a plant recognition test on the nature trail and the three comparison groups were tested on recognition of the same species in classroom. The testing materials consisted of 31 real plants outdoors and 31 photos taken of these real plant species that were shown to pupils from fourth, fifth and sixth classes (grade levels) from primary school. The qualitative methods were a questionnaire administered to pupils from elementary school and high school and students from the department of teacher education, to teachers from university and interviews, where 3 5 pupils and students who recognized the plant species best or worst in the recognition test were selected to be interviewed. Furthermore, classroom teachers from primary school and experts were interviewed. The research results showed that on average plant species were recognized insufficiently on every level of education. There was also variation between answers from primary school to university teachers. However, species recognition skills improved from primary school to university teachers. Among other things, sex and place of residence explained species recognition skills, because girls and pupils from rural areas knew plant species statistically significantly better than boys or pupil from cities. Almost every pupil, student and all classroom teachers wanted to recognize plant species better. Many pupils mentioned that a motivating teaching method would be to go outdoors and investigate the plant species themselves. University teachers and experts also mentioned that the best and most efficient learning and teaching method for species recognition skills, is to practice in nature. We should teach plant species in nature, using many senses and teaching methods. Also new technology could be used in teaching species recognition skills. Keywords: plant species recognition, plant species education, general education

Kuva tikkeinä kankaalla : Kokemuksia PE-design 6.0 -kirjontakuvion suunnitteluohjelman kahden automaattisen tekniikan käytettävyydestä

The aim of the thesis was to compare the correspondence of the outcome a computer assisted program appearance compared to the original image. The aspect of the study was directed to embroidery with household machines. The study was made from the usability point of view with Brother's PE-design 6.0 embroidery design programs two automatic techniques; multicoloured fragment design and multicoloured stitch surface design. The study's subject is very current because of the fast development of machine embroidery. The theory is based on history of household sewing machines, embroidery sewing machines, stitch types in household sewing machines, embroidery design programs as well as PE-design 6.0 embroidery design program's six automatic techniques. Additionally designing of embroidery designs were included: original image, digitizing, punching, applicable sewing threads as well as the connection between embroidery designs and materials used on embroidery. Correspondences of sewn appearances were examined with sewing experimental methods. 18 research samples of five original image were sewn with both techniques. Experiments were divided into four testing stages in design program. Every testing stage was followed by experimental sewing with Brother Super Galaxie 3100D embroidery machine. Experiments were reported into process files and forms made for the techniques. Research samples were analysed on images syntactic bases with sensory perception assessment. Original images and correspondence of the embroidery appearances were analysed with a form made of it. The form was divided into colour and shape assessment in five stage-similarity-scale. Based on this correspondence analysis it can be said that with both automatic techniques the best correspondence of colour and shape was achieved by changing the standard settings and using the makers own thread chart and edited original image. According to the testing made it is impossible to inform where the image editing possibilities of the images are sufficient or does the optimum correspondence need a separate program. When aiming at correspondence between appearances of two images the computer is unable to trace by itself the appearance of the original image. Processing a computer program assisted embroidery image human perception and personal decision making are unavoidable.

Chemical phytotoxicity testing facility for warm-season turfgrasses

The registration of new agricultural chemicals (particularly herbicides) for turf use requires supporting data on their possible phytotoxic effects across a representative range of turfgrass species and cultivars. This process has been streamlined by the establishment of dedicated phytotoxicity testing site. This facility has enabled phytotoxicity screening of new chemicals to be conducted more quickly, thoroughly and economically than the previous piecemeal ad hoc approach. During the three years of this project, 39 products were screened on the site.

Random Breath Testing Operation and Effectiveness in 1987

• In December 1986 funds were approved to double the intensity of random breath testing (RBT) and provide publicity support for police efforts. These changes were considered necessary to make RBT effective. • RBT methods were changed in the metropolitan area to enable block testing (pulling over a block of traffic rather than one or two cars), deployment of police to cut off escape routes, and testing by traffic patrols in all police subdivisions. Additional operators were trained for country RBT. • A publicity campaign was developed, aimed mainly at male drivers aged 18-50. The campaign consisted of the “cardsharp” television commercials, radio commercials, newspaper articles, posters and pamphlets. • Increased testing and the publicity campaigns were launched on 10 April 1987. • Police tests increased by 92.5% in May – December 1987, compared with the same period in the previous four years. • The detection rate for drinking drivers picked up by police who were cutting off escape routes was comparatively high, indicating that drivers were attempting to avoid RBT, and that this police method was effective at detecting these drivers. • A telephone survey indicated that drivers were aware of the messages of the publicity campaign. • The telephone survey also indicated that the target group had been exposed to high levels of RBT, as planned, and that fear of apprehension was the major factor deterring them from drink driving. • A roadside survey of driver blood alcohol concentrations (BACs) by the University of Adelaide’s Road Accident Research Unit (RARU) showed that, between 10p.m. and 3a.m., the proportion of drivers in Adelaide with a BAC greater than or equal to 0/08 decreased by 42%. • Drivers under 21 were identified as a possible problem area. • Fatalities in the twelve month period commencing May 1987 decreased by 18% in comparison with the previous twelve month period, and by 13% in comparison with the average of the previous two twelve month periods (commencing May 1985 and May 1986). There are indications that this trend is continuing. • It is concluded that the increase in RBT, plus publicity, was successful in achieving its aims of reductions in drink driving and accidents.

Random Breath Testing Operation and Effectiveness in 1985

Random breath testing (RBT) was introduced in South Australia in 1981 with the intention of reducing the incidence of accidents involving alcohol. In April 1985, a Select Committee of the Upper House which had been established to “review the operation of random breath testing in this State and any other associated matters and report accordingly” presented its report. After consideration of this report, the Government introduced extensive amendments to those sections of the Motor Vehicles Act (MVA) and Road Traffic Act (RTA) which deal with RBT and drink driving penalties. The amended section 47da of the RTA requires that: “(5) The Minister shall cause a report to be prepared within three months after the end of each calendar year on the operation and effectiveness of this section and related sections during that calendar year. (6) The Minister shall, within 12 sitting days after receipt of a report under subsection (5), cause copies of the report to be laid before each House of Parliament.” This is the first such report. Whilst it deals with RBT over a full year, the changed procedures and improved flexibility allowed by the revision to the RTA were only introduced late in 1985 and then only to the extent that the existing resources would allow.

Heat pipes-concepts, materials and applications

The heat pipe is an innovative engineering structure characterized by its capacity to transfer large quantities of heat through relatively small cross-sectional areas with very small temperature differences; it also possesses high thermal conductance and low thermal impedance. In recent times, heat pipes in various forms and designs have found a wide variety of applications. This paper briefly presents the basic concepts of heat pipes, recent innovations in design and their applications.

Development and feasibility testing of an education program to improve knowledge and self-care among Aboriginal and Torres Strait Islander patients with heart failure

Background/Aim There is a 70% higher age-adjusted incidence of heart failure (HF) amongst Aboriginal and Torres Strait Islander people, three times more hospitalisations and twice as many deaths than non-Aboriginal people. There is a need to develop holistic yet individualised approaches in accord with the values of Aboriginal community healthcare to support patient education and self-care. The aim of this study was to re-design an existing HF educational resource (Fluid Watchers-Pacific Rim©) to be culturally safe for Aboriginal and Torres Strait Islander peoples, working in collaboration with the local community, and to conduct feasibility testing. Methods This study was conducted in two phases and utilised a mixed methods approach (qualitative and quantitative). Phase 1 of this study used action research methods to develop a culturally safe electronic resource to be provided to Aboriginal HF patients via a tablet computer. A HF expert panel adapted the existing resource to ensure it was evidence-based and contained appropriate language and images that reflects Aboriginal culture. A stakeholder group (which included Aboriginal workers and HF patients, as well as researchers and clinicians) then reviewed the resources and changes were made accordingly. In Phase 2, the new resource was tested on a sample of Aboriginal HF patients to assess feasibility and acceptability. Patient knowledge, satisfaction and self-care behaviours were measured using a before and after design with validated questionnaires. As this was a pilot test to determine feasibility, no statistical comparisons were made. Results - Phase 1: Throughout the process of resource development, two main themes emerged from the stakeholder consultation. These were the importance of identity, meaning that it was important to ensure that the resource accurately reflected the local community, with the appropriate clothing, skin tone and voice. The resource was adapted to reflect this and of the local community voiced the recordings for the resource. The other theme was comprehension; images were important and all text was converted to the first person and used plain language. - Phase 2: Five Aboriginal participants, mean age 61.6 ± 10.0 years, with NYHA Class III and IV heart failure were enrolled. Participants reported a high level of satisfaction with the resource (83.0%). HF knowledge (percentage of correct responses) increased from 48.0 ± 6.7% to 58.0 ± 9.7%, a 20.8% increase and results of the self-care index indicated that the biggest change was in patient confidence for self-care with a 95% increase in confidence score (46.7 ± 16.0 to 91.1 ± 11.5). Changes in management and maintenance scores varied between9275 patients. Conclusion By working in collaboration with HF experts, Aboriginal researchers and patients, a culturally safe HF resource has been developed for Aboriginal and Torres Strait Islander patients. Engaging Aboriginal researchers, capacity-building, and being responsive to local systems and structures enabled this pilot study to be successfully completed with the Aboriginal community and positive participant feedback demonstrated that the methodology used in this study was appropriate and acceptable; participants were able to engage with willingness and confidence.

Kinnasneulatekniikan verkko-oppimateriaalin kehittäminen ja neulalla neulomisen taidon kehittyminen

The purpose of the study was to develop a functional web-based learning material for the learning of the nålbinding technique. The study of the research topic was already begun in my pedagogical thesis in 2008 by considering the demands on pedagogic material for the teaching of the technique. This study falls into the field of qualitative design research which was carried out through three stages. In the study three methods of usability testing, i.e. expert analysis, the informants’ thinking aloud and interviews, were used as research methods. At the first stage of the study the first version of the learning material was created. This was done on the basis of theoretical knowledge, the demands set on learning materials as clarified in previous studies, on the basis of previously created learning materials for the learning of the nålbinding technique as well as with the help of two experts on the technique. At the second stage, the learning material was developed on the basis of expert analysis and another version of the material was created. At the third stage, usability testing was carried out on the material. At this stage two informants used the material, practiced stitching with the nålbinding needle and thought aloud while doing so. In the usability testing the Morae –programme was used to record the events on the screen, the actions of the informants and their spoken out thoughts. The Morae –programme was also used when analysing the recordings. After the testing, the informants practised stitching independently and in a few weeks time they were interviewed. The interviews were aimed at finding out the informants’ opinions on the future development of the material. On the basis of the informants’ independent attempts at using the nålbinding technique, the development of their skills after the testing was also discussed at the interviews. The development of the learning material will continue after this study on the basis of the usability testing and the interviews. The web-based learning material was created for the website Käspaikka in the address www.kaspaikka.fi/kinnasneula. By creating a multimodal learning material the dual-coding theory by Paivio was taken into consideration. According to the theory, several methods of presentation help a learner to restore information in his/her memory. The independent construction of the learner’s knowledge, i.e. learning according to the principles of the constructivist learning theory, was also supported by creating a logical navigation system, by linking interrelated topics to one another and by presenting the topics in several different forms. In the test situations the learning material was judged to work well when practising stitching with the nålbinding needle. Both informants learned the basics of the nålbinding technique even though their respective learning strategies were quite different. In the usability testing illogicalities and shortcomings were still noticed in the learning material which will still be further developed in the future.