Avaliação da erosão hídrica, transporte de sedimentos e qualidade da água na bacia do córrego Monjolo Grande

Understanding the linkages between the natural elements is essential for being promoted the land use, occupation and sustainable management of environmental systems. Universal Soil Loss Equation (USLE), as a predictive model of erosion, is important to allowing the prevention of possible environmental impacts which may drastically interfere in natural or anthropic environments, as well as prevent potential financial wastes and even contribute to greater efficiency of agricultural production. This research will be working some USLE parameters, emphasizing topographic factor from Ribeirão Monjolo Grande watershed. Among the factors considered by the USLE, the Topographic Factor interferes directly in the erosive dynamic of a watershed because it involves variables related to hydrological processes that occur on it. In this research, were discussed different methods for obtaining the Topographic Factor (BERTONI e LOMBARDI NETO, 1985; MOORE e BURCH, 1986; DESMET E GOVERS, 1996) in GIS environment. After comparison between the methods, was indicated that best represents the conditions of geometry strand of the study area. Finally, other factors (R, K, C, P) considered by the USLE were obtained. The attainment of these parameters were guided by the use of geotechnologies, especially in Geographic Information Systems (GIS), with the assistance of secondary data and periodic field visits. The results obtained contributed to the understanding of hydrosedimentological dynamic in this area and serve as a viable strategy for studies of soil loss, aiming at developing consistent material for future researches about environmental planning and land management

O efeito da modalidade prévia sobre a subseqüente em provas de triatlo: aspectos fisiológicos e biomecânicos

O triatlo é uma modalidade combinada envolvendo outras três modalidades de endurance: natação, ciclismo e corrida, o que torna as necessidades biomecânicas e fisiológicas da modalidade combinada diferente das demandas e adaptações sofridas por treinamentos realizados nas modalidades de forma isolada. A fadiga imposta pela modalidade prévia poderá ser determinante no bom desempenho do atleta nas modalidades subseqüentes e neste sentido é importante analisarmos não apenas a influência do ciclismo sobre a corrida onde existe maior semelhança entre as fibras musculares recrutadas predominantemente, como a influência da natação sobre as demais modalidades. Algumas estratégias podem ser adotadas afim de minimizar a perda de performance que uma modalidade irá exercer sobre a subseqüente relacionadas a especificidade do treinamento e geração de adaptações específicas, estratégias de ritmo de prova, possibilidade de utilização do vácuo durante o percurso de ciclismo e da esteira na natação, utilização de roupas de neoprene na natação e adaptações na geometria do quadro da bicicleta.

O uso das TIC nas aulas de matemática na perspectiva do professor

The objective of this research is to understand whether the mathematics lessons teachers use ICT and how they see their use. For this, we prepared a questionnaire with four questions for the subjects of our research, which are ex - students of Bachelor in Mathematics FEG / UNESP, in exercise of the profession. The questionnaire data were analyzed following the procedures of phenomenological research. This approach enabled us to draw up three open categories. The first Recourse to boost student learning and school, leads us to interpret that for the interviewees, ICT resources are leading students to do research making them responsible for their learning and providing them with conditions respond the issues raised by the teacher, which generates greater interactivity. The second, Possibility to use software related to mathematical content shows that the subject sees ICT as resources that allow the study of mathematical content, especially geometry and functions, so that student learning is leverage. The third, Obstacles to the use of technology in the classroom shows that even if the subjects recognize the importance of ICT use, they do not use it as often as they would like because of the difficulties that are related to infrastructure and didactic and pedagogical conditions

Matemática e Arte: interdisciplinaridade

The objective of this study is to perform a theoretical study of the possible relationship between mathematics and art. For some people, the association between these fields of knowledge may simply seem absurd, possibly because they do not know what is in common between an area considered rigorous, rational, objective, and a more emotional, intuitive, subjective. In this context, interdisciplinarity has an important role, in proposing the contextual integration between the subject content, such as projective geometry and the renaissance. Are also presented as examples of this union, the technique of Moses and the geometric patterns of indigenous crafts, as well as the work of artist Maurits Cornelis Escher, a legitimate representative of the relationship between art and mathematics

Otimização do braço inferior da suspensão dianteira do veículo Baja utilizando o método dos elementos finitos

Mass reduction coupled with the mechanical performance in service has been the goal of many projects related to the transport area, considering the advantages that mass reduction can bring. However, make a simple material substitution without design a new geometry to corroborate for the best component performance, often makes the replacement unviable. In this study, it was investigated the advantages of replacing the prototype BAJA SAE front suspension lower arm of Equipe Piratas do Vale de BAJA SAE - Universidade Paulista, Campus Guaratinguetá, actually produced with steel, for a new component made of carbon fiber composite. The new geometry has been developed to provide the best possible performance for this component and your easy manufacturing. The study was done using the 3D modeling tools and computer simulations via finite element method. The first stage of this work consisted on calculation of the estimated maximum contact force tire / soil in a prototype landing after jump at one meter high, drop test in the laboratory with the current vehicle, current front suspension lower arm 3D modeling, finite element simulation and analysis of critical regions. After all current component analysis, a new geometry for the part in study was designed and simulated in order to reduce the component mass and provide a technological innovation using composite materials. With this work it was possible to obtain a theoretical component mass reduction of 25,15% maintaining the mechanical strength necessary for the appropriated component performance when incited

A utilização de sólidos geométricos com alunos do ensino fundamental

This research analyzed if the interactions between teacher and student, and among students, with the use of manipulative materials in the Mathematics teaching in a middle school class and provided the comprehension of the subjects worked. The analysis of the results was based in Vygotsky’s socio-historical theory, that prioritizes the interactions in learning-teaching process. The results of this research showed that these interactions mediated by the use of such materials provide the student with the motivation needed to take part in the math classes as an active actor in his development process, as well as understanding the concepts

Abordagem multivariada na análise de diversidade genética em cruzamentos para alto teor de óleo em soja

The soybean crop is considered a high expression around the world. In plant breeding programs, knowledge of genetic diversity is extremely important and in this context, are frequently used multivariate analyzes. Thus, the aim of the present study was to evaluate the genetic divergence between soybean crosses through multivariate techniques. In total, 16 crosses were evaluated, which were in the F2 generation of inbreeding. The evaluated characteristics were plant height at maturity, height of the first pod, number of branches per plant, number of pods per plant, number of nodes per plant, hundred seed weight, grain yield and oil content. For the analyzes was used Euclidean distance, methods of hierarchical clustering UPGMA and Ward and principal component analysis. Genetic distances estimated using Euclidean distance ranged from 1.24 to 8.13, with the smallest distance observed between crosses C1 and C4, and the greatest distance between the C2 crosses and C6. The methods UPGMA clustering and Ward met crossings in five different groups. The principal component analysis explained 86.2% of the variance contained in the original eight variables with three main components. The APM characters, NV, NR, NN, PG% and oil were the main contributors to genetic divergence among traits. Multivariate techniques were crucial to the analysis of genetic diversity, and the methods of Ward and UPGMA clustering and principal components have consistent results in this way, the simultaneous use of these tools in genetic analysis of crosses is indicated

Caracterização geológica da terminação norte do Domo de Ambrósio - Bahia

The Ambrósio dome is a granodioritic batholiths of elliptical geometry, 40km length in the N-S direction and variable width of up to 8 km, has a weakly deformed nucleus with intensely deformed margins, in its northern portion is intruded in orthogneiss that belong to the Archean basement, and its southern part comes in direct contact with the volcano-sedimentary sequence of Paleoproterozoic Rio Itapicuru Greenstone Belt (RIGB), Bahia. From geological mapping on 1:25:000 scale were recognized two structural domains, termed West Domain and East Domain. From investigation of these domains was identified a major shear zone, which puts in contact two distinct stratigraphic sequences, one west, consisting primarily of metavulcanic and metapyroclastic rocks with records of low-grade regional metamorphism, and east discontinuity a metassedimentary domain, with record of gradational contact metamorphism, deformation and compression generated from the rise of Ambrosio Pluton. Such records put into question the structural and stratigraphic models in the literature so far

Tratamento da superfície do alumínio via eletrólise a plasma

This paper presents the study on the application of the electrolytic plasma for surface treatment of aluminum. A bibliographical study on the material of interest was preliminarily performed and later designed and built an electrolytic cell, including the excitation source. Unlike conventional electrolysis process, the plasma assisted carry on in the non-linear region of characteristic current/voltage curve. Therefore it requires for the on set of the process that the power supply operates on harder conditions than those on high current process. The plasma produced during the present investigation has temperatures in the range o 6,0.10 3 -7,0 .10 3 K, well above those found in conventional chemical process. It also shows a particular dynamic to promote changes on surface and to produce new materials. The plasma is generated by microdischarge in vapor or gas bubbles involved in physic-chemical processes in electrode regions of the electrolytic cell. The electrode material was the aluminum (7075). The Process Electrolytic Plasma Processing (EPP) is sensitive to various parameters such as operating voltage, current density, electrolyte, concentration of electrolyte, geometry of reactor, temperature of electrolytic solution and dynamic of the fluid in the cell. The experiments were carried on in order to find parameters for a stable abd steady operation. The choice for the electrolytic was silicate/alkali solution in various concentrations to operate in various voltage as well. Plasma was produced on negative (cathode) and positive (anode) electrode, in specific conditions. A stable operation on the cathode process was obtained with low concentration of the electrolytic in aqueous solution, current density around 250V effective voltage. For the evolution of plasma in anodic process it was required higher concentrations and higher... (Complete abstract click electronic access below)

Obtenção e caracterização de compósitos via RTM com alta fração de fibras de carbono processados à temperatura ambiente

After confirming the high specific mechanical properties of composite materials by scientific studies conducted over the last decades, one of the challenges of this new class of materials is the ability to achieve mass production at a more affordable cost, which has become indispensable. The Resin Transfer Molding (RTM) is an excellent method for manufacturing composite materials. Despite being a process widely used by international companies in the production of high performance structural composites, only a short time the national aviation industry has shown interest in implementing this type of processing to more complex structures and greater structural responsibility. In aeronautical projects, the reproducibility and the relative low cost of this process, several studies have been performed in Brazil for learning and perfecting this technique. This process is suitable for producing polymer components both simple as complex geometry, and allows to achieve consistent thickness, with high quality finish and without limiting range. Polymeric composite components for the high mechanical stress applications such as aircraft structures, satellites, etc., require a strict control of volume fractions of the composite constituents, beyond the knowledge of their mechanical and thermal properties. Therefore, in this experimental work degree study on the mechanical, thermal and of porosity composites processed by RTM processed characterization was performed. This characterization was performed targeting a possible aerospace application of this composite material. For the production of composites, process equipment (RTM RTM injector Radius 2100cc) was used. The processed carbono/epoxy composites were characterized via flexure tests mechanically and thermally analysis via DMA, DSC and TGA. To determine the volume fraction of fibers, the composite samples were analyzed via matrix digestion (ASTM D3171) ... (Complete abstract click electronic access below)

Revisão teórico bibliográfica sobre o espraiamento da nasalidade no português do Brasil com especial destaque para o dialeto paulista

O espraiamento da nasalização é um fenômeno observado desde estudos antigos sobre a língua portuguesa. Tanto com as consoantes nasais em posição de coda, quanto com elas em posição de onset, nota-se a interferência gerada nas vogais que as acompanham. O atual estudo aborda como eram percebidas e estudadas as nasais e seu espraiamento, demonstrando como a nasalização pode ser descrita, por seus segmentos fonéticos – demonstrando quais elementos a compõem – e por suas marcas suprassegmentais. Detalha-se também a importância de estudos realizados sobre a nasalidade dentro da geometria de traços. Faz-se levantamento geral do fenômeno do espraiamento da nasalidade, através de estudos gerais da nasalidade e da teoria fonética e fonológica relativa ao fenômeno

Corpos intrusivos básicos na coluna sedimentar Permo-Carbonífera no vale do rio Corumbataí

As rochas intrusivas básicas associadas a Formação Serra Geral na porção sul do município de Rio Claro e norte de Piracicaba configuram geometrias na forma de diques e soleiras. Estes corpos estão associados à uma parte da Bacia Sedimentar do Paraná que foi deformada por eventos tectônico que resultaram em trends preferencias NW-SE, condicionando a estratigrafia, a intrusão e geometria dos corpos de diabásio e formação da estrutura domática do alto de Pitanga. Os corpos intrusivos tem em sua maioria a forma de soleiras e em menor quantidade a forma de diques. A compreensão destes corpos é importante para o entendimento da estratigrafia da área conhecida como domo de Pitanga na região de Rio e Piracicaba

Contagem automatizada de veículos utilizando segmentação estatística

In this work was developed a program capable of performing automatic counting of vehicles on roads. The problem of counting vehicles is using expensive techniques for its realization, techniques which often involve manual counting or degradation of the pavement. The main motivation for this work was the importance that the vehicle counting represents to the Traffic Engineer, being essential to analyze the performance of the roads, allowing to measure the need for installation of traffic lights, roundabouts, access ways, among other means capable of ensuring a continuous flow and safe for vehicles. The main objective of this work was to apply a statistical segmentation technique recently developed, based on a nonparametric linear regression model, to solve the segmentation problem of the program counter. The development program was based on the creation of three major modules, one for the segmentation, another for the tracking and another for the recognition. For the development of the segmentation module, it was applied a statistical technique combined with the segmentation by background difference, in order to optimize the process. The tracking module was developed based on the use of Kalman filters and application of simple concepts of analytical geometry. To develop the recognition module, it was used Fourier descriptors and a neural network multilayer perceptron, trained by backpropagation. Besides the development of the modules, it was also developed a control logic capable of performing the interconnection among the modules, mainly based on a data structure called state. The analysis of the results was applied to the program counter and its component modules, and the individual analysis served as a means to establish the par ameter values of techniques used. The find result was positive, since the statistical segmentation technique proved to be very useful and the developed program was able to count the vehicles belonging to the three goal..

Evolução tectônica do Trend Badejo-Linguado-Pampo, bacia de Campos (RJ)

The regional geological work for the oil industry, in order to find potential areas for hydrocarbon exploration and understand the geological parameters responsible for the formation of the deposit are known importance. This work fits into that scenario, with regional research with the aid of wells and 2D and 3D seismic sold by DBEP (Database Exploration and Production). Were also used as GeoGraphix software package Landmarks modules Prizm and SeisWork 2D and 3D, and the Surfer 8 and ArcGIS 9.2 with the infrastructure provided by the 05 PRH - ANP with LSGI (Laboratory of Seismic and Geological Interpretation) located at UNESP -- Campus de Rio Claro. The work focuses on study the trend of oil-Badejo-Linguado-Pampo, producing fields since the beginning of offshore holdings. The Campos Basin is now known as the offshore basin of the country more productive, and the high structural Badejo is a structure of great importance in the basin presents itself as largely responsible for the conditioning of hydrocarbon fields Pampo, Linguado and Badejo. Therefore this work also aims to increase knowledge of the region in terms of tectonic and stratigraphic characterize the geometry of the structures associated with this major regional structure. For this we used structural contour maps of the main chrono-horizons, and Isopach maps for the purpose of better understanding the tectono-sedimentary evolution of the Campos Basin locally.

Concentração de tensões em peças e componentes estruturais - uma abordagem através do método dos elementos finitos

Any failure process that may occur in a part probably is located where the stress exceeded the level of resistance. When a part or component has a sharp change in geometry, such as slots, holes, grooves, bumps or other irregularities, there is an increased concentration of stress at a specific location of the part. The objective of this study is to determine the maximum stresses in structural parts and components using the equations of elasticity theory in conjunction with the stress concentration factor experiment and compare them with results obtained by finite element method