COMPARAÇÃO DE PROCESSAMENTOS MATEMÁTICOS DE DADOS VOLTAMÉTRICOS: APLICAÇÃO NA DETERMINAÇÃO SIMULTÂNEA DE FLUOROQUINOLONAS

This paper describes a comparative study between the procedures of deconvolution and the second-order derivative of square wave voltammograms to achieve separation of the voltammetric peaks of levofloxacin (LEVO) and norfloxacin (NOR), for their simultaneous quantification in urine samples. The obtained results indicate that the use of second-derivative voltammograms coupled with carbon screen-printed electrodes is the most efficient approach for completely separating the voltammetric peaks of LEVO and NOR. In addition, this approach has produced detection limits lower than 1.0 µmol L-1 and a wide linear range for both drugs. The proposed method was successfully used to simultaneously determine LEVO and NOR in spiked human and bovine urine samples with recovery percentages close to 100% for all analyzed samples.

Separation of Gas Bubbles from Circulation Waters and Pulp Suspensions in Open Channel Flow

The objective of this thesis was to study the removal of gases from paper mill circulation waters experimentally and to provide data for CFD modeling. Flow and bubble size measurements were carried out in a laboratory scale open gas separation channel. Particle Image Velocimetry (PIV) technique was used to measure the gas and liquid flow fields, while bubble size measurements were conducted using digital imaging technique with back light illumination. Samples of paper machine waters as well as a model solution were used for the experiments. The PIV results show that the gas bubbles near the feed position have the tendency to escape from the circulation channel at a faster rate than those bubbles which are further away from the feed position. This was due to an increased rate of bubble coalescence as a result of the relatively larger bubbles near the feed position. Moreover, a close similarity between the measured slip velocities of the paper mill waters and that of literature values was obtained. It was found that due to dilution of paper mill waters, the observed average bubble size was considerably large as compared to the average bubble sizes in real industrial pulp suspension and circulation waters. Among the studied solutions, the model solution has the highest average drag coefficient value due to its relatively high viscosity. The results were compared to a 2D steady sate CFD simulation model. A standard Euler-Euler k-ε turbulence model was used in the simulations. The channel free surface was modeled as a degassing boundary. From the drag models used in the simulations, the Grace drag model gave velocity fields closest to the experimental values. In general, the results obtained from experiments and CFD simulations are in good qualitative agreement.

Molecular characterization of Brazilian Dicyma pulvinata isolates

Forty-nine Brazilian Dicyma pulvinata isolates were examined by morphological traits and RFLP, RAPD and AFLP analyses. This fungus is a mycoparasite of Microcyclus ulei, the causal agent of the most devastating rubber (Hevea brasiliensis) disease, known as "South American Leaf Blight" (SALB). These isolates were compared with an Indian isolate from Cercosporidium sp., and a French isolate from Cladosporium fulvum. They were also compared with Dicyma ampullifera from Papua New Guinea. The morphological parameters analyzed confirmed the identification of the Brazilian isolates. The graphic representations of the distance matrices of each molecular marker showed similar results. Dicyma pulvinata isolates from M. ulei were closely related, whereas the reference isolates examined were dispersed. Among the D. pulvinata isolates obtained from M. ulei, a significant pairwise distance was obtained, for all the molecular markers, between the isolates from the areas favorable to the occurrence of SALB (North and Northeast of Brazil) and the region of escape for the disease (Mato Grosso State).

Biological and molecular characterization of an isolate of Tobacco streak virus obtained from soybeans in Brazil

A virus was isolated from soybean (Glycine max) plants with symptoms of dwarfing and bud blight in Wenceslau Braz County, Paraná, Brazil. The host range and properties resembled those of Tobacco streak virus (TSV). The purified virus showed three peaks in a frozen sucrose gradient. Antiserum was produced and the virus was serologically related to TSV. Electron microscopy detected 28 nm spherical particles. Coat protein (CP) had a Mr of 29.880 Da. A fragment of 1028 nt was amplified, cloned and sequenced. One open reading frame with 717 nt was identified and associated to the CP. The CP gene shared 83% identity with the sequence of TSV CP from white clover (Trifolium repens) (GenBank CAA25133). This is the first report of the biological and molecular characterization of TSV isolated from soybeans. It is proposed that this isolate be considered a strain of TSV named TSV-BR.

Avaliação da tolerância de cultivares de soja à ferrugem asiática no oeste da Bahia

A utilização de tolerância como forma de controle da ferrugem da soja (Glycine max), causada pelo fungo Phakopsora pachyrhizi, pode ser uma alternativa viável, visto que a resistência qualitativa tem-se mostrado instável, em função da variabilidade do fungo. Este trabalho foi realizado na região oeste da Bahia, na safra 2003/04, com objetivo de avaliar a tolerância das principais cultivares de soja utilizadas na região. Foram avaliadas quatro cultivares de ciclo precoce [MG/BR 46 (Conquista), Emgopa 315, BRS Corisco e M-SOY 8411] e quatro cultivares de ciclo tardio (BRS Barreiras, M-SOY 9350, FT 106 e BRS Sambaíba). A tolerância foi quantificada pela diferença de produtividade entre subparcelas tratadas e não tratadas com fungicida. As cultivares MG/BR 46 (Conquista) e M-SOY 8411 apresentaram diferenças de rendimento não significativas, no entanto, essa característica não pôde ser atribuída à tolerância, em função da baixa severidade observada no ensaio. Essa diferença pôde ser atribuída a escape, uma vez que, no momento em que a ferrugem obteve valores mais elevados de severidade, as duas cultivares já estavam na fase final de desenvolvimento. Embora a severidade máxima observada no ensaio tenha sido baixa (30,5% para a cultivar BRS Barreiras), com exceção das cultivares MG/BR 46 (Conquista) e M-SOY 8411, as demais cultivares avaliadas apresentaram diferença significativa entre as subparcelas tratadas e não tratadas com fungicida, mostrando ausência de tolerância das principais cultivares comerciais cultivadas no oeste da Bahia. Neste trabalho, foi observado que as cultivares de ciclo precoce apresentaram reduções de produtividade inferiores às de ciclo tardio.

Liferay -portaalin kapasiteetin skaalaaminen

Liferay on avoimen lähdekoodin verkkoportaali, jonka avulla pienet ja keskisuuret yritykset voivat tarjota pilvityyppisiä verkkopalveluita asiakkailleen. Portaalin kapasiteetin eli portaalin ohjelmistoa ajavien tietokoneiden määrän kasvattaminen ja laskeminen ei ole käytännössä helppoa. Tämän diplomityön tarkoituksena on ollut kehittää ratkaisu, jonka avulla portaalin kapasiteettia voidaan monitoroida sekä nostaa ja laskea käytännöllisesti. Työssä on toteutettu verkko-ohjelmisto, joka toimii työkaluna tätä tarkoitusta varten. Tuloksena on ohjelmisto, jonka avulla verkkoportaalin ylläpitäjä kykenee tekemään tarkkoja johtopäätöksiä verkkoportaalia ajavien tietokoneiden kuormituksesta sekä käynnistämään ja sammuttamaan portaalin ohjelmiston etäältä. Tästä hyötynä on tarkempi verkkoportaalin kuormituksen mittaus, jonka pohjalta ylläpitäjä voi tehdä järkeviä johtopäätöksiä portaalin kapasiteetin nostamisesta ja laskemisesta. Mistä tuloksena verkkoportaalin tarjoama palvelu on varautunut käyttäjiensä kulutuksen huippuihin ja laskuihin.

Thermal behavior of alginic acid and its sodium salt

An evaluation of hydration and thermal decomposition of HAlg and its sodium salt is described using thermogravimetry (TG) and differential scanning calorimetry (DSC). TG curves in N2 and air, were obtained for alginic acid showed two decomposition steps attributed to loss of water and polymer decomposition respectively. The sodium alginate decomposed in three steps. The first attributed to water loss, followed by the formation of a carbonaceous residue and finally the Na2CO3. DSC curves presented peaks in agreement with the TG data. In the IR alginic acid presented bands at 1730 and 1631 cm-1, while sodium alginate presented a doublet at 1614 e 1431 cm-1, evidencing the presence of salified carboxyl groups.

The Influence of Certain Processing Factors on the Durability of Yttrium Stabilized Zirconia Used As Dental Biomaterial

In dentistry, yttrium partially stabilized zirconia (ZrO2) has become one of the most attractive ceramic materials for prosthetic applications. The aim of this series of studies was to evaluate whether certain treatments used in the manufacturing process, such as sintering time, color shading or heat treatment of zirconia affect the material properties. Another aim was to evaluate the load-bearing capacity and marginal fit of manually copy-milled custom-made versus prefabricated commercially available zirconia implant abutments. Mechanical properties such as flexural strength and surface microhardness were determined for green-stage milled and sintered yttrium partially stabilized zirconia after different sintering time, coloring process and heat treatments. Scanning electron microscope (SEM) was used for analyzing the possible changes in surface structure of zirconia material after reduced sintering time, coloring and heat treatments. Possible phase change from the tetragonal to the monoclinic phase was evaluated by X-ray diffraction analysis (XRD). The load-bearing capacity of different implant abutments was measured and the fit between abutment and implant replica was examined with SEM. The results of these studies showed that the shorter sintering time or the thermocycling did not affect the strength or surface microhardness of zirconia. Coloring of zirconia decreased strength compared to un-colored control zirconia, and some of the colored zirconia specimens also showed a decrease in surface microhardness. Coloring also affected the dimensions of zirconia. Significantly decreased shrinkage was found for colored zirconia specimens during sintering. Heat treatment of zirconia did not seem to affect materials’ mechanical properties but when a thin coating of wash and glaze porcelain was fired on the tensile side of the disc the flexural strength decreased significantly. Furthermore, it was found that thermocycling increased the monoclinic phase on the surface of the zirconia. Color shading or heat treatment did not seem to affect phase transformation but small monoclinic peaks were detected on the surface of the heat treated specimens with a thin coating of wash and glaze porcelain on the opposite side. Custom-made zirconia abutments showed comparable load-bearing capacity to the prefabricated commercially available zirconia abutments. However, the fit of the custom-made abutments was less satisfactory than that of the commercially available abutments. These studies suggest that zirconia is a durable material and other treatments than color shading used in the manufacturing process of zirconia bulk material does not affect the material’s strength. The decrease in strength and dimensional changes after color shading needs to be taken into account when fabricating zirconia substructures for fixed dental prostheses. Manually copy-milled custom-made abutments have acceptable load-bearing capacity but the marginal accuracy has to be evaluated carefully.

Kaupunkialueella toimivan sähkönjakeluverkkoyhtiön siirtohinnoittelun kehittäminen

Sähkönjakeluverkkoyhtiöllä on sähkön siirtopalveluun alueellinen monopoli. Siirtohinnoittelun reunaehdot tulevat sähkömarkkinalaista ja hintojen kohtuullisuutta valvoo ja sääntelee Energiamarkkinavirasto. Tässä työssä selvitetään Turku Energia Sähköverkot Oy:lle kustannusvastaavat aiheuttamisperiaatteen mukaiset siirtohinnat. Samalla muodostetaan yleis-, yö- ja kausituotteiden perusmaksuihin asiakkaan liittymispisteen pääsulakkeen kokoon perustuva porrastus. Sulakeporrastuksen käyttöönotolla pystytään kehittämään siirtohinnoittelun kustannusvastaavuutta ja noudattamaan aiheuttamisperiaatteen mukaista hinnoittelupolitiikkaa entistä paremmin. Työssä tutkitaan siirtohinnoittelun kehitysnäkymiä myös pidemmällä tähtäimellä. Älykkäiden sähköverkkojen kehittyminen ja erityisesti etäluettavien mittareiden käyttöönotto tulevat luomaan kehitysmahdollisuuksia siirtohinnoitteluun tulevaisuudessa. Laitteista saatavia tarkkoja sähkönkulutus- ja tehotietoja voidaan käyttää kustannusvastaavuuslaskennan taustalla. Jotta verkon käyttö olisi sen mitoitukseen nähden mahdollisimman tehokasta, tulisi kuorman jakautua mahdollisimman tasaisesti ajan suhteen. Verkossa esiintyviä kulutushuippuja pystytään tulevaisuudessa mahdollisesti tasoittamaan esimerkiksi kuorman ohjauksen avulla, jonka tehokeinona voidaan käyttää siirtohinnoittelua. Siirtohinnoilla voidaan mahdollisesti vaikuttaa myös esimerkiksi kulutuksen ja tuotannon ajoittamiseen sekä kannusta asiakkaita loistehon kompensointiin. Siirtotuotteiden täytyy myös kehittyä asiakkaiden tarpeiden kehittymisen rinnalla ja esimerkiksi sähkön laadun tuotteistaminen voi olla eräs keino vastaamaan tiukentuneisiin vaatimuksiin.

The Cellular Oxygen Sensor PHD2 in Cancer Growth

Adequate supply of oxygen is essential for the survival of multicellular organisms. However, in several conditions the supply of oxygen can be disturbed and the tissue oxygenation is compromised. This condition is termed hypoxia. Oxygen homeostasis is maintained by the regulation of both the use and delivery of oxygen through complex, sensitive and cell-type specific transcriptional responses to hypoxia. This is mainly achieved by one master regulator, a transcription factor called hypoxiainducible factor 1 (HIF-1). The amount of HIF-1 is under tight oxygen-dependent control by a family of oxygen-dependent prolyl hydroxylase domain proteins (PHDs) that function as the cellular oxygen sensors. Three family members (PHD1-3) are known to regulate HIF of which the PHD2 isoform is thought to be the main regulator of HIF-1. The supply of oxygen can be disturbed in pathophysiological conditions, such as ischemic disorders and cancer. Cancer cells in the hypoxic parts of the tumors exploit the ability of HIF-1 to turn on the mechanisms for their survival, resistance to treatment, and escape from the oxygen- and nutrient-deprived environment. In this study, the expression and regulation of PHD2 were studied in normal and cancerous tissues, and its significance in tumor growth. The results show that the expression of PHD2 is induced in hypoxic cells. It is overexpressed in head and neck squamous cell carcinomas and colon adenocarcinomas. Although PHD2 normally resides in the cytoplasm, nuclear translocation of PHD2 was also seen in a subset of tumor cells. Together with the overexpression, the nuclear localization correlated with the aggressiveness of the tumors. The nuclear localization of PHD2 caused an increase in the anchorage-independent growth of cancer cells. This study provides information on the role of PHD2, the main regulator of HIF expression, in cancer progression. This knowledge may prove to be valuable in targeting the HIF pathway in cancer treatment.

Clones de Hevea brasiliensis de alta productividad caracterizados por resistencia a Microcyclus ulei en jardin clonal en el magdalena medio colombiano

Con el objetivo de introducir en la región del magdalena medio de Colombia nuevos clones de caucho (Hevea brasiliensis (Willd. ex A. Juss.) Müll. Arg.) de alta productividad y con resistencia al Mal de las Hojas, se evaluaron materiales un jardín clonal establecido en Cimitarra, Colombia en la región del magdalena medio. Se evaluó la incidencia y la severidad del ataque de Microcyclus ulei (P. Henn.) von Arx. según Garcia et al. (1). Se encontró resistencia completa al mal de las hojas para los clones CDC 312, FDR 4575, FDR 5597, FDR 5788 y MDF 180 y resistencia parcial para los clones FX 3864 y CDC 32. Los clones RRIM 901, PB 235 y PB 260 se mostraron como susceptibles. De acuerdo con los resultados, los clones con resistencia total y parcial se podrán recomendar para zonas preferenciales con restricción para el cultivo, una vez este comportamiento se corroboré en campo clonal. En cuanto a los clones susceptibles se pueden recomendar para zonas de escape al mal de las hojas en el Magdalena Medio Colombiano.

Projeto terapêutico singular no âmbito da saúde mental: uma experiência no curso de graduação em medicina

O Jardim Campo Belo, localizado no município de Campinas (SP), é um bairro de alta vulnerabilidade social e grande demanda por serviços de saúde, sendo a única oferta em saúde mental o matriciamento com outra unidade de saúde. Neste contexto, durante as disciplinas do segundo ano de Medicina, foi realizado um projeto de intervenção no Centro de Saúde, mediante acompanhamento em domicilio de pacientes usuários de psicotrópicos. Realizaram-se visitas quinzenais às casas de dez pacientes. Nestas visitas, trabalhou-se um roteiro semidirigido, em que se buscou conhecer as demandas de cada paciente. Alguns destes aumentaram os cuidados com a própria saúde, e num caso houve até suspensão do uso dos medicamentos psicotrópicos, em parceria com a equipe; em outros casos, as visitas serviram como válvula de escape social, tornando-se um espaço onde se ofertava atenção aos que estavam acostumados ao abandono social. Os alunos envolvidos relatam grande aprendizado graças às vivências e ao envolvimento com o tema, que se tornou um grande suplemento pedagógico.

DYNAMICS OF LEAF FALL FROM RIPARIAN VEGETATION AND THE ACCUMULATION IN BENTHIC STOCK IN NEOTROPICAL STREAMS1

ABSTRACT Considering the importance of the riparian vegetation leaves as an energetic source to first order streams, the aim of the present study was to evaluate the leaf biomass contribution to the system and its temporal dynamics. With this purpose, monthly samples from July 2008 to June 2009 were collected using four sampling devices installed in three streams, in order to collect the vertical, lateral and terrestrial loads, and the benthic stock. We tested the following hypothesis: (1) leaf biomass input is higher after hydric stress periods; and (2) benthic stock biomass increase with higher loads from vertical and lateral entrances. Leaves represented 71.9% (on average) of all sampled allochthonous matter, with seasonal significant variation along the studied year. Peaks of leaf input were registered in September-October, after an increase in rainfall, and also in January, after a decrease in rainfall. Leaf input was higher in the lateral load.

Suorakulmaisten palonrajoittimien valmistettavuuden kehittäminen

Palonrajoittimet ovat tuotteita, jotka estävät tulen ja savun leviämisen palo-osastosta toiseen ja mahdollistavat ihmisten turvallisen ulospääsyn palotilanteessa. Tämän diplomityön tavoitteena oli vähentää suorakulmaisten palonrajoittimien valmistuskustannuksia niiden valmistettavuutta kehittämällä. Työn teoriaosassa käsitellään valmistettavuutta ja kokoonpantavuutta kehittäviä menetelmiä DFM:ää (Design for Manufacturability) ja DFA:ta (Design for Assembly) sekä palonrajoittimien ja ohutlevytuotteiden erityispiirteitä. Käytännön osuudessa esitellään tutkimusta varten valmistetut kolme kehitettävää palonrajoitinta, joita vertaillaan myös kilpaileviin tuotteisiin. Tuotteista analysoidaan osamääriä, materiaalikustannuksia ja työaikoja. Palonrajoittimien ongelmakohtia olivat muun muassa liittäminen ja kokoonpantavuus. Työssä esitetään keinoja palonrajoitinten valmistusystävälliseen suunnitteluun ja uusi moduloitu tuoteperhemalli, jolla vähennetään varsinkin valmistuksesta aiheutuvia kiinteitä kustannuksia. Lisäksi työssä esitetään alustava runkoratkaisumalli uudelle tuoteperheelle.

Dry months in the agricultural region of Ribeirão Preto, state of São Paulo-Brazil: an study based on the extreme value theory

The application of the Extreme Value Theory (EVT) to model the probability of occurrence of extreme low Standardized Precipitation Index (SPI) values leads to an increase of the knowledge related to the occurrence of extreme dry months. This sort of analysis can be carried out by means of two approaches: the block maxima (BM; associated with the General Extreme Value distribution) and the peaks-over-threshold (POT; associated with the Generalized Pareto distribution). Each of these procedures has its own advantages and drawbacks. Thus, the main goal of this study is to compare the performance of BM and POT in characterizing the probability of occurrence of extreme dry SPI values obtained from the weather station of Ribeirão Preto-SP (1937-2012). According to the goodness-of-fit tests, both BM and POT can be used to assess the probability of occurrence of the aforementioned extreme dry SPI monthly values. However, the scalar measures of accuracy and the return level plots indicate that POT provides the best fit distribution. The study also indicated that the uncertainties in the parameters estimates of a probabilistic model should be taken into account when the probability associated with a severe/extreme dry event is under analysis.