Dry sliding wear behaviour of magnesium alloy based hybrid composites in the longitudinal direction

In the present investigation, the wear behaviour of a creep-resistant AE42 magnesium alloy and its composites reinforced with Saffil short fibres and SiC particles in various combinations is examined in the longitudinal direction i.e., the plane containing random fibre orientation is perpendicular to the steel counter-face. Wear tests are conducted on a pin-on-disc set-up under dry sliding condition having a constant sliding velocity of 0.837 m/s for a constant sliding distance of 2.5 km in the load range of 10-40 N. It is observed that the wear rate increases with increase in load for the alloy and the composites, as expected. Wear rate of the composites is lower than the alloy and the hybrid composites exhibit a lower wear rate than the Saffil short fibres reinforced composite at all the loads. Therefore, the partial replacement of Saffil short fibres by an equal volume fraction of SiC particles not only reduces the cost but also improves the wear resistance of the composite. Microstructural investigation of the surface and subsurface of the worn pin and wear debris is carried out to explain the observed results and to understand the wear mechanisms. It is concluded that the presence of SiC particles in the hybrid composites improves the wear resistance because these particles remain intact and retain their load bearing capacity even at the highest load employed, they promote the formation of iron-rich transfer layer and they also delay the fracture of Saffil short fibres to higher loads. Under the experimental conditions used in the present investigation, the dominant wear mechanism is found to be abrasion for the AE42 alloy and its composites. It is accompanied by severe plastic deformation of surface layers in case of alloy and by the fracture of Saffil short fibres as well as the formation of iron-rich transfer layer in case of composites.

Studies on friction and formation of transfer layer when Al-4Mg alloy pins slid at various numbers of cycles on steel plates of different surface texture

In the present investigation, various kinds of textures, namely, unidirectional, 8-ground, and random were attained on the die surfaces. Roughness of the textures was varied using different grits of emery papers or polishing powders. Then pins made of Al-4Mg alloys were slid against steel plates at various numbers of cycles, namely 1, 2, 6, 10 and 20 under both dry and lubricated conditions using an inclined pin-on-plate sliding tester. The morphologies of the worn surfaces of the pins and the formation of transfer layer on the counter surfaces were observed using a scanning electron microscope. Surface roughness parameters of the plate were measured using an optical profilometer. It was observed that the coefficient of friction and formation of transfer layer during the first few cycles depend on the die surface textures under both dry and lubricated conditions. It was also observed that under lubricated condition, the coefficient of friction decreases with number of cycles for all kinds of textures. However, under dry condition, it ecreases for unidirectional and 8-ground surfaces while for random surfaces it increases with number of cycles

Adoption of environmental assurance in pastoral industry supply chains - Market failure and beyond

This paper describes adoption rates of environmental assurance within meat and wool supply chains, and discusses this in terms of market interest and demand for certified 'environmentally friendly' products, based on phone surveys and personal interviews with pastoral producers, meat and wool processors, wholesalers and retailers, and domestic consumers. Members of meat and wool supply chains, particularly pastoral producers, are both aware of and interested in implementing various forms of environmental assurance, but significant costs combined with few private benefits have resulted in low adoption rates. The main reason for the lack of benefits is that the end user (the consumer) does not value environmental assurance and is not willing to pay for it. For this reason, global food and fibre supply chains, which compete to supply consumers with safe and quality food at the lowest price, resist public pressure to implement environmental assurance. This market failure is further exacerbated by highly variable environmental and social production standards required of primary producers in different countries, and the disparate levels of government support provided to them. Given that it is the Australian general public and not markets that demand environmental benefits from agriculture, the Australian government has a mandate to use public funds to counter this market failure. A national farm environmental policy should utilise a range of financial incentives to reward farmers for delivering general public good environmental outcomes, with these specified and verified through a national environmental assurance scheme.

Structure of a peptide oxazolone: 2-(1'-benzyloxycarbonylamino-1'-methylethyl)-4,4-dimethyl-5-oxazolone

C16H20N204, monoclinic, P21, a = 6.270 (1),b= 11.119(3),c= ll.640(4)A, fl= 100.7 (2)°,Dm = 1-27 (flotation), Dc = 1-26 Mg m -3, Z = 2. The structure has been refined to a final R value of 0.041 for 1584 independent counter-measured reflections. The oxazolone ring in the molecule is nearly planar. The exocyclic O atom is 0.065 A out of the plane defined by the other four atoms in the ring belonging to the lactone group. The difference in length between the two adjacent C-O bonds in the ring is small, but significant. The crystal structure is stabilized by van der Waals interactions and a N--H... N hydrogen bond.

Koulukasvatusta teknologisoituvaan yhteiskuntaan : Kansakoulun opetussuunnitelman rakentuminen, 1945-1952

Education for a Technological Society. Public School Curriculum Construction, 1945-1952. The subject of my research is the significance of technology in the construction process of the public school curriculum during the years 1945-1952. During the period the war reparation and rebuilding placed demands and actions to rationalise and dramatise industry and agriculture. Thereby the ambitions of building a technological country and the reformation of curriculum took place simultaneously. Fordistian terms of reference, of which the principles were mass production, rationalisation and standardisation, a hierarchical division of labour and partition of assignments, provided a model for the developing curriculum. In the research the curriculum is examined as an artefact, which shapes socio-technically under the influence of social and technical factors. In the perspective of socio-technical construction the artefact is represented by the viewpoints of members of relevant social groups. The groups give meaning to the curriculum artefact, which determines the components of the curriculum. The weakness of the curriculum was its ineffectiveness, which was due to three critical problems. Firstly, the curriculum was to be based on scientific work, which meant the development of schools through experiments and scientific research. Secondly, the civilised conseption in the curriculum was to be composed of theoretical knowledge, as well as practical skills. Practical education was useful for both the individual and society. Thirdly, the curriculum was to be reformed in a way that the individuality of the pupil would be taken into account. It was useful for the society that talents and natural abilities of every pupil were observed and used to direct the pupil to the proper place in the social division of labour, according to the "right man in a right place" principle. The solutions to critical problems formed the instructions of the public school curriculum, which described the nature and content of education. Technology and its development were on essential part of the whole school curriculum process. The quality words connected to the development of technology - progress, rationality and effectiveness - were also suitable qualifiers and reasons for the reform of the curriculum. On the other hand, technology set a point of comparison and demand for the development of all phases of education. The view of technology was not clearly deterministic - it was also possible to shape technological society with the help of education. The public school curriculum process indicates how originally the principles of technological systems were shaped to the language of education and accepted in educational content.

Lapsi, lapsuus ja perhe varhaiskasvatusasiakirjoissa 1967-1999

The aim of this study is to describe and interpret discourses in Finnish national early childhood education and care (ECEC) documents concerning the child, childhood and family, including preschool education of six-year-old children. The study begins with preparation phase of the Act on Children s Day Care (1967) and concludes with the definition of ECEC policy (1999). The research data consists of committee memoranda and national ECEC curriculum guidelines. The total number of documents studied was 20, comprising some 1700 pages. The research data was examined with qualitative text analysis and employed a discursive approach. A semiotic square (Greimas rectangle) served as a tool for clarifying the discourses and constructions reflected in the research data. The theoretical framework of the study consists of the theories of childhood and family studies. The main concepts from childhood studies used in this study were childhood as a cultural construct and child-centred pedagogy in ECEC. The theoretical approaches from family studies used were the formation of modern and late-modern parenthood and family, as well as the concept of familism. Two main discursive lines were constructed from the ECEC documents. The notion of universalistic childhood suggests that early education and care aim to create the same good childhood for all children, regardless of their family background or living area. The second discursive line followed in the documents is the familistic discourse. This discourse contains emphasis on the priority of parental care. The construct of the competent child was found in the research data as early as in the mid-1970s. On the other hand, the construct of the weak family is distinguishable throughout almost the entire research period. This raises the question of whether Finnish ECEC system has been developed for the competent and self-sufficient child of a weak family which needs constant support and guidance of welfare experts. According to the study, it appears that within the Finnish ECEC system the relatively heavy emphasis on social work rather than on early education has been legitimised by the construct of the weak family. This study also shows that a more thorough analysis should be given to what we mean when we say that the main task of ECEC system is to support families in the upbringing of their children. The study was completed during the period when historical decisions concerning the administration in Finland were in the making (i.e. the potential transfer of ECEC services from the Ministry of Social Affairs and Health to the Ministry of Education). Also, over the past decade, a major reformation of the Act on Children s Daycare has been on the agenda, but no concrete measures have been implemented. Based on the findings of this study, we can ask for what kind of child and family we are preparing the ECEc reforms of the new millennium. Key words: ECEC policy Finland, childhood, family, familism, discourse analysis, semiotic square

A simple, wide-range, linear thermistor-based temperature indicator

A novel thermistor-based temperature indicator using an RC oscillator and an up/down counter has been developed and described. The indicator provides linear performance over a wide dynamic temperature range of 0-100°C. This indicator is free from the error due to lead resistances of the thermistor and gives a maximum error of ±0 · 1°C in the range 0-100°C. Test results are given to support the theory.

L-Arginine L-aspartate

C6HxsN40 +.C4H6NO~-, monoclinic, P2,,a = 5.511 (3), b = 8.438 (4), c = 15.265 (9) A, fl = 97.9 (I) °, D,, -- 1.467 (8) (flotation), D c = 1.452 Mg m -a, Z = 2. The structure has been refined to a final R value of 0.044 for 1226 independent counter-measured reflections. The conformation of the arginine molecule is different from those previously observed, whereas the conformation of the aspartate ion is similar to that found in L-aspartic acid, DL-aspartic acid and L-lysine L-aspartate. The unlike molecules aggregate into separate alternating layers and the a-amino and acarboxylate groups in the arginine layer are periodically brought into close proximity in a 'headto-tail' arrangement. There exist a specific ion-pair interaction involving electrostatic attraction and two nearly parallel N-H...O hydrogen bonds between the guanidyl group and the a-carboxylate group of the aspartate ion.

Structure Of A Thionucleoside - 5'-Deoxy-5',6-Epithio-5,6-Dihydro-2',3'-Ortho-Isopropylidene-3-Methyluridine

C13HlsN205 S, M r = 314.35, orthorhombic, P212121 with a = 39.526 (4), b = 6.607 (2), c = 5.661 (2) A, Z = 4, V = 1478.36 A 3, D c = 1.412 Mg m -3, Cu Ka radiation. Final R = 0.073 for 1154 observed counter reflections. The sulphur atom is in a pseudo-equatorial position with respect to the dihydrouracil ring. The sugar pucker is predominantly O(l')-exo unlike the C(3')-exo,C(4')-endo observed for 2',3' O-isopropylideneuridine (ISPU). The fivemembered dioxolane ring has C(7) displaced by 0.497 (7)A from the best plane through atoms 0(2'), C(2'), C(3'), 0(3'), in contrast to ISPU where 0(3') shows the maximum deviation.

On the functional ordering of biomembranes : Implications for drug binding

Cells are packed with membrane structures, defining the inside and outside, and the different subcellular compartments. These membranes consisting mainly of phospholipids have a variety of functions in addition to providing a permeability barrier for various compounds. These functions involve cellular signaling, where lipids can act as second messengers, or direct regulation of membrane associating proteins. The first part of this study focuses on relating some of the physicochemical properties of membrane lipids to the association of drug compounds to membranes. A fluorescence based method is described allowing for determination of the membrane association of drugs. This method was subsequently applied to a novel drug, siramesine, previously shown to have anti-cancer activity. Siramesine was found to associate with anionic lipids. Especially interesting is its strong affinity for a second messenger lipid phosphatidic acid. This is the first example of a small molecule drug compound specifically interacting with a cellular lipid. Phosphatidic acid in cells is required for the activation of many signaling pathways mediating growth and proliferation. This provides an intriguing possibility for a simple molecular mechanism of the observed anti-cancer activity of siramesine. In the second part the thermal behavior and self assembly of charged and uncharged membrane assemblies was studied. Strong inter-lamellar co-operativity was observed for multilamellar DPPC vesicles using fluorescence techniques together with calorimetry. The commonly used membrane models, large unilamellar vesicles (LUV) and multilamellar vesicles (MLV) were found to possess different biophysical properties as interlamellar interactions of MLVs drive segregation of a pyrene labeled lipid analogue into clusters. The effect of a counter-ion lattice on the self assembly of a cationic gemini surfactant was studied. The presence of NaCl strongly influenced the thermal phase behavior of M-1 vesicles, causing formation of giant vesicles upon exceeding a phase transition temperature, followed by a subsequent transition into a more homogenous dispersion. Understanding the underlying biophysical aspects of cellular membranes is of fundamental importance as the complex picture of the structure and function of cells is evolving. Many of the cellular reactions take place on membranes and membranes are known to regulate the activity of many peripheral and intergral membrane associating proteins. From the point of view of drug design and gene technology, membranes can provide an interesting target for future development of drugs, but also a vehicle sensitive for environmental changes allowing for encapsulating drugs and targeting them to the desired site of action.

Gel growth and dielectric studies of K. Rb and Cs perchlorates

Single crystals of K, Rb and Cs perchlorates have been grown by the counter diffusion of the respective ions and CIO4 through the gel medium. Studies on nucleation, growth kinetics, morphological aspects and purity are discussed in this paper. The dielectric constant, ~b, as well as loss measured along the longest axis, exhibits an anomaly at the transition temperature, Tt, in all the three crystals. It is found that the peak values of Tt are approximately 800, 100 and 53 in K, Rb and Cs perchlorates, respectively. The dielectric anomaly and the large value of c b in the cubic phase are discussed in terms of the degree of disorder of the CIO~ group and the possible contribution from defects.

The decline of northern malaria and population dynamics of Plamodium vivax

Europe was declared malaria free in 1975. The disappearance of malaria has traditionally been attributed to numerous deliberate actions like vector control, the screening of houses, more efficient medication etc. Malaria, however, disappeared from many countries like Finland before any counter measures had even started. The aim of this thesis is to study the population ecology of P. vivax and its interaction with the human host and the vector. By finding the factors that attributed to the extinction of vivax malaria it might be possible to improve the modern strategy against P. vivax. The parasite was studied with data from Finland, which provides the longest time series (1749-2008) of malaria statistics in the world. The malaria vectors, Anopheles messeae and A. beklemishevi are still common species in the country. The eradication of vivax malaria is difficult because the parasite has a dormant stage that can cause a relapse long after a primary infection. It was now shown that P. vivax is able to detect the presence of a potential vector. A dormant stage is triggered even from a bite of an uninfected Anopheles mosquito. This optimizes the chances for the Plasmodium to reach a mosquito vector for sexual reproduction. The longevity of the dormant stage could be shown to be at least nine years. The parasite spends several years in its human host and the behaviour of the human carrier had a profound impact on the decline of the disease in Finland. Malaria spring epidemics could be explained by a previous warm summer. Neither annual nor summer mean temperature had any impact on the long term malaria trend. Malaria disappeared slowly from Finland without mosquito control. The sociological change from extended families to nuclear families led to decreased household size. The decreased household size correlated strongly with the decline of malaria. That led to an increased isolation of the subpopulations of P. vivax. Their habitat consisted of the bedrooms in which human carriers slept together with the overwintering vectors. The isolation of the parasite ultimately led to the extinction of vivax malaria. Metapopulation models adapted to local conditions should therefore be implemented as a tool for settlement planning and socio-economic development and become an integrated part of the fight against malaria.

Gravity-induced coronal plane joint moments in adolescent idiopathic scoliosis

Background Adolescent Idiopathic Scoliosis is the most common type of spinal deformity, and whilst the risk of progression appears to be biomechanically mediated (larger deformities are more likely to progress), the detailed biomechanical mechanisms driving progression are not well understood. Gravitational forces in the upright position are the primary sustained loads experienced by the spine. In scoliosis they are asymmetrical, generating moments about the spinal joints which may promote asymmetrical growth and deformity progression. Using 3D imaging modalities to estimate segmental torso masses allows the gravitational loading on the scoliotic spine to be determined. The resulting distribution of joint moments aids understanding of the mechanics of scoliosis progression. Methods Existing low-dose CT scans were used to estimate torso segment masses and joint moments for 20 female scoliosis patients. Intervertebral joint moments at each vertebral level were found by summing the moments of each of the torso segment masses above the required joint. Results The patients’ mean age was 15.3 years (SD 2.3; range 11.9 – 22.3 years); mean thoracic major Cobb angle 52° (SD 5.9°; range 42°-63°) and mean weight 57.5 kg (SD 11.5 kg; range 41 – 84.7 kg). Joint moments of up to 7 Nm were estimated at the apical level. No significant correlation was found between the patients’ major Cobb angles and apical joint moments. Conclusions Patients with larger Cobb angles do not necessarily have higher joint moments, and curve shape is an important determinant of joint moment distribution. These findings may help to explain the variations in progression between individual patients. This study suggests that substantial corrective forces are required of either internal instrumentation or orthoses to effectively counter the gravity-induced moments acting to deform the spinal joints of idiopathic scoliosis patients.

Wild dog control impacts on calf wastage in extensive beef cattle enterprises

Wild dogs (Canis lupus dingo and hybrids) are routinely controlled to protect beef cattle from predation yet beef producers are sometimes ambivalent as to whether wild dogs are a significant problem or not. This paper reports the loss of calves between birth and weaning in pregnancy-tested herds located on two beef cattle properties in south-central and far north Queensland for up to 4 consecutive years. Comparisons of lactation failures (identified when dams that previously tested pregnant were found non-lactating at weaning) were made between adjoining test herds grazed in places with or without annual (or twice annual) wild dog poison baiting programs. No correlation between wild dog relative abundance and lactation failures was apparent. Calf loss was frequently higher (three in 7 site-years, 11–32%) in baited areas than in non-baited areas (9% in 1 of 7 site-years). Predation loss of calves (in either area) only occurred in seasons of below-average rainfall, but was not related to herd nutrition. These data suggest that controlling wild dogs to protect calves on extensive beef cattle enterprises is unnecessary in most years because wild dogs do not routinely prey on calves. In those seasons when wild dog predation might occur, baiting can be counter-productive. Baiting appears to produce perturbations that change the way surviving or re-colonising wild dog populations select and handle prey and/or how they interact with livestock.

AC conductivity of a quantum Hall line junction

We present a microscopic model for calculating the AC conductivity of a finite length line junction made up of two counter-or co-propagating single mode quantum Hall edges with possibly different filling fractions. The effect of density-density interactions and a local tunneling conductance (sigma) between the two edges is considered. Assuming that sigma is independent of the frequency omega, we derive expressions for the AC conductivity as a function of omega, the length of the line junction and other parameters of the system. We reproduce the results of Sen and Agarwal (2008 Phys. Rev. B 78 085430) in the DC limit (omega -> 0), and generalize those results for an interacting system. As a function of omega, the AC conductivity shows significant oscillations if sigma is small; the oscillations become less prominent as sigma increases. A renormalization group analysis shows that the system may be in a metallic or an insulating phase depending on the strength of the interactions. We discuss the experimental implications of this for the behavior of the AC conductivity at low temperatures.