Feasibility of ASH DEC‐ process in treating sewage sludge and manure ash in Finland

In Finland the thermal treatment of sewage sludge has been moderate in 21th century. The reason has been the high moisture content of sludge. During 2005-2008, 97-99% of sewage sludge was utilized in landscaping and agriculture. However agricultural use has been during 2005-2007 less than 3 %. The aim of national waste management plan is that by 2016 100% of sludge is used either as soil amendment or energy. The most popular utilization method for manure is spreading it on arable land. The dry manures such as poultry manure and horse manure could also be used in incineration. The ashes could be used as fertilizers and while it is not suitable as a starter fertilizer, it is suitable in maintaining P levels in the soil. One of the main drivers for more efficient nutrient management is the eutrophication in lakes and the Baltic See. ASH DEC process can be used in concentrating phosphorus rich ashes while separating the heavy metals that could be included. ASH DEC process uses thermochemical treatment to produce renewable phosphate for fertilizer production. The process includes mixing of ashes and chlorine donors and subsequent treatment in rotary kiln for 20 min in temperature of 900 – 1 050 oC. The heavy metals evaporate and P-rich product is obtained. The toxic substances are retained in air pollution control system in form of mixed metal hydroxides. The aim of conducting this study is to estimate the potential of ASH DEC process in treating phosphorus rich ashes in Finland. The masses considered in are sewage sludge, dry manure from horses, and poultry and liquid pig manure. To date the usual treatment method for sewage sludge in Finland is composting or anaerobic digestion. Part of the amount of produced sewage sludge (800 kt/a fresh mass and 160 kt/a TS) could also be incinerated and the residual ashes used in ASH DEC process. Incinerating only manure can be economically difficult to manage because the incineration of manure is in Finland considered as waste incineration. Getting a permit for waste incineration is difficult and also small scale waste incineration is too expensive. The manure could act as an additional feedstock in counties with high density of animal husbandry where the land area might not be enough for spreading of manure. Now when the manure acts as a supplementary feedstock beside sludge, the ash can’t be used directly as fertilizer. Then it could be used in ASH DEC process. The perquisite is that the manure producers could pay for the incineration, which might prove problematic.

Descrição morfológica e morfométrica da glândula vesicular de cobaias durante o desenvolvimento pós-natal

Glândulas vesiculares são essenciais para a reprodução, pois suas secreções afetam a função espermática. Cobaias (Cavia porcellus) são um excelente modelo experimental para estudo destas glândulas, contudo não existem dados morfológicos e morfométricos durante seu desenvolvimento. Neste estudo a morfologia (projeções das pregas (PP) e altura das células epiteliais (AE) da túnica mucosa) e a morfometria (massa (MG), volume (VG), comprimento (CG), largura das porções cranial (LCR), média (LM) e caudal (LCA)) das glândulas vesiculares foram determinadas em cobaios (N= 25) com uma (S1), três (S3), cinco (S5), oito (S8) e onze (S11) semanas de idade (N=5/grupo de idade). Em adição massa (MC), comprimento (CC) e altura (AC) corporais e o índice organo-somático (IOS) foram também determinados e o coeficiente de correlação (r) estabelecido entre as variáveis. As glândulas restringiam-se a cavidade pélvica e tinham seu interior repleto de uma massa semi-sólida e, após a S8, ocuparam também a cavidade abdominal e tiveram o conteúdo aumentado significativamente. A túnica mucosa era pregueada e forrada de um epitélio simples colunar. MC, CC e AC aumentaram continuamente com a idade. MG, VG, CG e LCA não se alteraram da S1 a S5 e aumentaram na S8; enquanto que MF, VG e LCA também aumentaram na S11. IOS e PP aumentaram na S8 e S11 e AE na S5, S8 e S11. Houve (r) significativo entre a idade, Bc e MFg,; IOS e MG na S8 e S11; idade e PP; idade e AE e entre PP e AE. Em conclusão, as glândulas vesiculares de cobaios seguiram o padrão morfológico observado em ratos e hamsters, mas diferiram em alguns aspectos de outros histricomorfos, podendo ser utilizadas como modelo experimental e seu desenvolvimento morfológico e morfométrico podem ser divididos em três fases: da S1 a S5, quando são discretos; da S6 a S8 de idade, quando são acentuados de maneira geral e após a S8, quando há incremento intenso da capacidade secretória.

Avaliação lectino-histoquímica de fígado e rim de ovinos com fotossensibilização causada por Brachiaria decumbens

Embora sejam as forrageiras mais importantes para a pecuária de corte (bovinocultura de corte) no Brasil, em certas épocas ou condições, Brachiaria spp. podem ser tóxicas e causar surtos de fotossensibilização hepatógena que determinam significativas perdas econômicas. Animais que se alimentam em pastos de Brachiaria spp. comumente apresentam macrófagos espumosos isolados ou agrupados, além de cristais no interior de ductos biliares. Saponinas esteroidais têm sido identificadas nestes cristais e são responsabilizadas por lesar o fígado levando ao acúmulo de filoeritrina. Por vezes, imagens negativas desses cristais podem estar presentes no citoplasma de macrófagos espumosos. A patogênese de formação e o tipo de material armazenado nas células espumosas ainda são desconhecidos. A técnica de lectino-histoquímica visa auxiliar na detecção desses macrófagos e, consequentemente, no diagnóstico, além de identificar quais os resíduos de açúcares específicos que estão presentes no citoplasma das células espumosas. Assim, este trabalho teve por objetivo identificar quais lectinas são mais indicadas na detecção de saponinas esteroidais no fígado e rim de ovinos com fotossensibilização causada por Brachiaria decumbens. Fragmentos de fígado e rim de quinze ovinos, de ambos os sexos e idade variável, oriundos de Conceição do Mato Dentro, Minas Gerais, e um ovino mantido em pastagem livre de Brachiaria spp. foram avaliados pela técnica de lectino-histoquímica. Quatorze lectinas foram utilizadas (Con-A, DBA, SBA, PNA, SJA, RCA-I, UEA-I, WGA, SWGA, GSL, PSA, PHA-L, PHA-E e LCA). Verificou-se que, no fígado de ovinos com fotossensibilização provocada pela ingestão de Brachiaria decumbens, a lectina PNA apresentou especificidade e acentuada reatividade aos macrófagos espumosos, bem como especificidade e leve reatividade aos hepatócitos; a lectina WGA teve especificidade e moderada reatividade aos macrófagos espumosos do fígado e especificidade e leve reatividade aos hepatócitos; e as lectinas SBA, GSL e LCA apresentaram especificidade e moderada reatividade aos macrófagos espumosos, entretanto, não foram específicas para hepatócitos. No rim dos ovinos, a lectina PNA foi a que apresentou maior reatividade. Avaliações lectino-histoquímicas ainda não haviam sido realizadas em fígado e rim de ovinos com fotossensibilização provocada por Brachiaria spp.

The effects of location, feedstock availability, and supply-chain logistics on the greenhouse gas emissions of forest-biomass energy utilization in Finland

Forest biomass represents a geographically distributed feedstock, and geographical location affects the greenhouse gas (GHG) performance of a given forest-bioenergy system in several ways. For example, biomass availability, forest operations, transportation possibilities and the distances involved, biomass end-use possibilities, fossil reference systems, and forest carbon balances all depend to some extent on location. The overall objective of this thesis was to assess the GHG emissions derived from supply and energy-utilization chains of forest biomass in Finland, with a specific focus on the effect of location in relation to forest biomass’s availability and the transportation possibilities. Biomass availability and transportation-network assessments were conducted through utilization of geographical information system methods, and the GHG emissions were assessed by means of lifecycle assessment. The thesis is based on four papers in which forest biomass supply on industrial scale was assessed. The feedstocks assessed in this thesis include harvesting residues, smalldiameter energy wood and stumps. The principal implication of the findings in this thesis is that in Finland, the location and availability of biomass in the proximity of a given energyutilization or energy-conversion plant is not a decisive factor in supply-chain GHG emissions or the possible GHG savings to be achieved with forest-biomass energy use. Therefore, for the greatest GHG reductions with limited forest-biomass resources, energy utilization of forest biomass in Finland should be directed to the locations where most GHG savings are achieved through replacement of fossil fuels. Furthermore, one should prioritize the types of forest biomass with the lowest direct supply-chain GHG emissions (e.g., from transport and comminution) and the lowest indirect ones (in particular, soil carbon-stock losses), regardless of location. In this respect, the best combination is to use harvesting residues in combined heat and power production, replacing peat or coal.

Importance of considering food waste in the development of sustainable food packaging systems

Meeting the needs of both present and future generations forms the foundation of sustainable development. Concern about food demand is increasing alongside the continuously growing population. In the pursuit of food security preventing food waste is one solution avoiding the negative environmental impacts that result from producing food unnecessarily. Packages offer one answer to preventing food waste, as they 1) preserve and protect food, 2) introduce the user to the correct way to handle and use the food and package and 3) allow the user to consume the food in its entirety. This thesis aims to enhance the sustainability of food packages by giving special emphasis to preventing food waste. The focus of this thesis is to assist the packaging designer in being able to take into account the requirements for the sustainability of food packages and to be able to integrate these requirements into the product development process. In addition, life cycle methods that can be used as a tool in the packaging design process or in assessing the sustainability of finished food-packaging combinations are evaluated. The methods of life cycle costing (LCC) and life cycle working environment (LCWE) are briefly discussed. The method of life cycle assessment (LCA) is examined more thoroughly through the lens of the literature review of food-package LCA case studies published in the 21st century in three relevant journals. Based on this review and on experiences learned from conducting LCAs, recommendations are given as to how the LCA practitioner should conduct a food packaging study to make most of the results. Two case studies are presented in this thesis. The first case study relates the results of a life cycle assessment conducted for three food items (cold cut (ham), sliced dark bread (rye) and Soygurt drink) and the alternative packaging options of each. Results of this study show that the packaging constitutes only 1–12 % of the total environmental impacts of the food-packaging combination. The greatest effect is derived from the food itself and the wasted food. Even just a small percentage of wasted food causes more environmental impacts than does the packaging. The second case study presents the results of LCC and LCWE analysis done for fruit and vegetable transport packages. In this thesis, the specific results of the study itself are not the focus, but rather the study methods and scope are analysed based on how these complement the sustainability assessment of food packages. This thesis presents reasons why prevention of food waste should be more thoroughly taken into account in food packaging design. In addition, the task of the packaging designer is facilitated by the requirements of sustainable food packaging, by the methods and step-by-step guidance on how to integrate sustainability issues into the design process, and by the recommendations on how to assess the sustainability of food packages. The intention of this thesis is to express the issues that are important in the field of the food packaging industry. Having recognised and implemented these issues, businesses can better manage the risks that could follow from neglecting these sustainability aspects.

The consequences of e-HRM on line managers

The purpose of this research was to provide a deeper insight into the consequences of electronic human resource management (e-HRM) for line managers. The consequences are viewed as used information system (IS) potentials pertaining to the moderate voluntaristic category of consequences. Due to the need to contextualize the research and draw on line managers’ personal experiences, a qualitative approach in a case study setting was selected. The empirical part of the research is loosely based on literature on HRM and e-HRM and it was conducted in an industrial private sector company. In this thesis, method triangulation was utilized, as nine semi-structured interviews, conducted in a European setting, created the main method for data collection and analysis. Other complementary data such as HRM documentation and statistics of e-HRM system usage were utilized as background information to help to put the results into context. E-HRM has partly been taken into use in the case study company. Line managers tend to use e-HRM when a particular task requires it, but they are not familiar with all the features and possibilities which e-HRM has to offer. The advantages of e-HRM are in line with the company’s goals. The advantages are e.g. an transparency of data, process consistency, and having an efficient and easy-to-use tool at one’s disposal. However, several unintended, even contradictory, and mainly negative outcomes can also be identified, such as over-complicated processes, in-security in use of the tool, and the lack of co-operation with HR professionals. The use of e-HRM and managers’ perceptions regarding e-HRM affect the way in which managers perceive the consequences of e-HRM on their work. Overall, the consequences of e-HRM are divergent, even contradictory. The managers who considered e-HRM mostly beneficial to their work found that e-HRM affects their work by providing information and increasing efficiency. Those managers who mostly perceived challenges in e-HRM did not think that e-HRM had affected their role or their work. Even though the perceptions regarding e-HRM and its consequences might reflect the strategies, the distribution of work, and the ways of working in all HRM in general and can’t be generalized as such, this research contributed to the field of e-HRM and it provides new perspectives to e-HRM in the case study organization and in the academic field in general.

Collection Development Policy 2009–2015 Of The National Library Of Finland

The collections policy of the National Library of Finland guides the formation and development of collections. The policy also outlines the National Library’s collection, its national and international significance, and the guidelines for acquisition, selection, donation and disposal.

Mineraalisen rakennusjätteen hyötykäyttö maarakentamisessa

Työn tavoitteena on osoittaa betonimurskeen ympäristökelpoisuus maarakennuskäytössä sekä vertailla betonimurskeen ja luonnonmateriaalien elinkaaren aikaisia ympäristövaikutuksia maarakentamisessa. Teoriaosassa käsitellään betonimurskeen maarakennuskäyttöön vaikuttavaa lainsäädäntöä ja sen mahdollisia ympäristövaikutuksia. Lisäksi käydään läpi neitseellisten maarakennusmate-riaalien otosta aiheutuvia ympäristövaikutuksia. Työn kokeellinen osa koostuu kahdesta osasta: materiaalien haitallisten aineiden liukoisuuden mää-rityksistä ja elinkaariarvioinnista. Liukoisuuden määritykset tehtiin kenttäkokeina luonnonolosuhteissa Lahden tiede- ja yrityspuisto Oy:n Jokimaan pilot-luokan maaperätutkimuskeskuksessa. Lisäksi liukoisuudet määritettiin laboratoriossa valtioneuvoston asetuksen eräiden jätteiden hyödyntämisestä maarakentamisessa vaatimusten mukaisesti. Elinkaariarvioinnissa vertailtiin betonimursketta neitseellisiin maarakennusmateriaaleihin skenaarioissa, jotka sisälsivät materiaalin valmistuksen ja kuljetuksen käyttökohteeseen. Neitseellisiä materiaaleja käytettäessä oletettiin, että betoni loppusijoitetaan kaatopaikalle. Elinkaariarvioinnissa käytettiin Gabi-elinkaarimallinnusohjelmaa ja skenaarioita vertailtiin hiilidioksidiekvivalenttipäästöihin. Lisäksi elinkaariarviointiin otettiin mukaan vielä kehitysvaiheessa oleva menetelmä maankäytön indikaattoreiden määrittämiseen. Menetelmällä tutkittiin soranoton vaikutusta soraharjun maaperän laadulle ennen ja jälkeen soranoton. Tulokseksi liukoisuuden määrityksistä saatiin, että betonimurskekerroksen läpi suotautuneen sade-veden pH nousee hyvin emäksiseksi. pH:n nousu vaikuttaisi korreloivan positiivisesti tiettyjen metallien liukoisuuteen. Huomattavaa on, että kenttäkokeiden liukoisuudet ja laboratoriossa määritetyt liukoisuudet poikkesivat joltain osin toisistaan. Elinkaaritarkastelussa hiilidioksidiekvivalentti päästöjen suhteen suurin päästö aiheutuu, jos betoni loppusijoitetaan kaatopaikalle hyötykäytön sijaan. Maaperän laadun muutoksien määrittämisen menetelmä ei vielä ole käyttökelpoinen lähtötietojen yksinkertaistuksien ja puutteiden takia. Betonimurskeen hyötykäyttö maarakentamisessa ei aiheuta merkittäviä ympäristövaikutuksia, kun altistus vedelle minimoidaan. Lisäksi hyötykäyttö on suositeltava vaihtoehto loppusijoitukselle kaatopaikan rakentamisen ja käytön aiheuttamien ympäristövaikutusten takia.

Fotossíntese de biótipos de azevém sob condição de competição

As características associadas à atividade fotossintética de biótipos de azevém, resistente e suscetível ao herbicida glyphosate, foram avaliadas sob diferentes níveis de competição entre biótipos. O experimento foi realizado em esquema fatorial 2 x 5, com dois biótipos de azevém, resistente e suscetível ao glyphosate, cultivados em planta única no centro da parcela, competindo com zero, um, dois, três ou quatro plantas do biótipo oposto. Cinqüenta dias após a emergência, foram determinadas a taxa de fluxo de gases pelos estômatos (U - µmol s-1), a concentração de CO2 subestomática (Ci - µmol mol-1) e a taxa fotossintética (A - µmol m-2 s-1), sendo calculado ainda o CO2 consumido (ΔC - µmol mol-1) a partir dos valores de CO2 de referência e CO2 na câmara de avaliação. Os dados foram coletados utilizando-se analisador de gases no infravermelho (IRGA), marca ADC, modelo LCA 4. Foi elaborada matriz de correlação entre as variáveis. Os biótipos de azevém resistente e suscetível ao glyphosate não diferiram quanto à atividade fotossintética na ausência de competição. No entanto, a taxa fotossintética foi reduzida com o aumento na intensidade de competição com plantas do biótipo oposto, tanto para o biótipo resistente como para o suscetível, e também para o biótipo resistente quando em competição com plantas do mesmo biótipo. Atribuiu-se tal comportamento ao aumento no sombreamento mútuo e à competição por luz.

Comparison of sustainability of technologies for water desalination

The aim of this work is to perform an in-depth overview on the sustainability of several major commercialized technologies for water desalination and to identify the challenges and propose suggestions for the development of water desalination technologies. The overview of those technologies mainly focuses on the sustainability from the viewpoint of total capital investment, total product cost, energy consumption and global warming index. Additionally, a systematic sustainability assessment methodology has been introduced to validate the assessment process. Conclusions are:1) Reverse osmosis desalination (RO) plants are better than multi-stage flash distillation (MSF) desalination plants and multiple-effect distillation (MED) desalination plants from the viewpoint of energy consumption, global warming index and total production cost; 2)Though energy intensive, MSF plants and MED plants secure their advantages over RO plants by lower total capital investment, wider applicability and purer water desalted and they are still likely to flourish in energy-rich area;3) Water production stage and wastewater disposal stage are the two stages during which most pollutant gases are emitted. The water production stage alone contributes approximately 80~90% of the total pollutant gases emission during its life cycle; 4)The total capital cost per m3 desalted water decreases remarkably with the increasing of plant capacity. The differences between the capital cost per m3 desalted water of RO and other desalination plants will decrease as the capacity increases; 5) It is found that utilities costs serve as the major part of the total product cost, and they account for 91.16%, 85.55% and 71.26% of the total product cost for MSF, MED and RO plants, respectively; 6) The absolute superiority of given technology depends on the actual social-economic situation (energy prices, social policies, technology advancements).

Kuivajätehuollon hiilijalanjälki ja kustannukset sekä kuljetusten kilpailutus – Etelä-Karjalan aluekeräyspisteverkoston päivitys

Tutkimuksen tavoitteena oli yhtenäistää Etelä-Karjalan alueen erilaisia tapoja toimia alueke-räyksen suhteen. Aluekeräyksellä tarkoitetaan jätteiden keräystä pisteiltä, joihin kotitaloudet, jotka eivät kuulu kiinteistökohtaiseen keräykseen, voivat tuoda syntypaikkalajitellun kuiva- eli sekajätteensä. Tavoitteena oli myös saada tietoa siitä, minkälaiset ovat eri kuivajätehuoltovaihtoehtojen ilmastonmuutos- ja kustannusvaikutukset. Lisäksi tavoitteena oli selvittää, miten ympäristönäkökohdat voidaan ottaa huomioon kuljetuskilpailutuksissa. Tutkimuksessa kerättiin tietoa internetistä, opinnäytetöistä ja tieteellisistä artikkeleista sekä yritysten edustajilta. Kasvihuonekaasupäästöjen laskennassa hyödynnettiin GaBi 6.0 -elinkaariarviointiohjelmaa. Tutkimuksen perusteella aluekeräyspisteet kannattaa sijoittaa reiteille, joita asukkaat käyttävät vähintään kerran viikossa ja mitkä ovat optimaalisesti myös kuljetusurakoitsijan kannalta. Taajama-alueelle ei nähty suositeltavaksi sijoittaa aluekeräyspisteitä. Suositeltavina astioina aluekeräyspisteille nähtiin syväkeräyssäiliöt, joiden tyhjennys onnistuu samalla keräyskalustolla kuin kiinteistöjen jäteastioiden, kun ajoneuvo on varustettu puominosturilla. Suositeltavaksi nähtiin myös harventaa jäteastioiden talvityhjennystiheyksiä, jos tyhjennystiheys on vakio ympäri vuoden, sillä pääosa aluekeräyspisteiden käyttäjistä on loma-asukkaita. Tyhjennystiheyksien harvennuksella olisi mahdollista saavuttaa kustannussäästöjä. Tutkimuksessa laskettiin kuivajätteen elinkaarenaikaisia kasvihuonekaasupäästöjä kuivajätteen keräyksestä loppusijoitukseen ja energiahyötykäyttöön. Energiahyötykäyttökohteiksi valittiin Riihimäen, Kotkan sekä Leppävirran (suunnitteilla) jätteenpolttolaitokset. Tulosten pohjalta kuivajätteen energiahyötykäyttö oli loppusijoitusta selkeästi parempi vaihtoehto. Kuivajätteen keräys- ja kuljetuspäästöjen vaikutus oli pieni. Kuivajätteen kuljetusmatkan pituus jätteenpolttolaitokselle ei ole siis ratkaisevassa roolissa kokonaiskasvihuonekaasupäästöjä tarkasteltaessa. Etäisyyttä suurempi vaikutus onkin kuivajätteen koostumuksella, polttolaitosten vuosihyötysuhteilla ja korvattavilla polttoaineilla. Jatkossa suositellaan selvittämään vielä vaihtoehtoisia käsittelytapoja kuivajätteen sisältämälle sekamuovijakeelle, jonka poltosta aiheutuu merkittävä osuus (noin 74 %) kuivajätteen polton kasvihuonekaasupäästöistä. Ajankohtaisia kuljetuskilpailutuksia varten tarkasteltiin vielä tarkemmin keräys- ja kuljetuspäästöjä. Tulosten pohjalta havaittiin, että keräys- ja kuljetuspäästöjä on mahdollista vähentää reilusti (46–74 %) siirtymällä dieselistä biopolttoaineiden käyttöön. Tuloksiin vaikuttaa kuitenkin merkittävästi, minkälaisista raaka-aineista biopolttoaineet on valmistettu. Kuivajätteen keräyspäästöjä on mahdollista pienentää myös päivittämällä aluekeräyspisteverkostoa. Tutkimuksessa tarkasteltiin kustannuksia aluekeräyspisteiden astioiden uusinnasta tai korjauksesta kuivajätteen loppusijoitukseen tai energiahyötykäyttöön asti. Merkittävimmät kustannukset aiheutuivat kuivajätteen loppusijoituksesta, energiahyötykäytöstä sekä keräyksestä. Kustannusten näkökulmasta keräyksen rooli oli siis suurempi. Työn lopussa annettiin vielä vinkkejä, joiden avulla jätehuoltoyritykset voivat tehdä jätekuljetushankintoja ympäristönäkökohdat huomioiden. Usein selkein tapa huomioida ympäristönäkökohdat kuljetuskilpailutuksissa on asettaa riittävän tiukkoja pakollisia vaatimuksia, jolloin voi valita hinnaltaan halvimman vaihtoehdon. Kuljetuspalvelun hankinnassa tulee huomioida ainakin energiankulutus, hiilidioksidi-, typenoksidi-, hiilivety- ja hiukkaspäästöt. Lainsäädäntö ei määrää vähimmäistasoja, vaan hankintaa tehdessä kannattaa kartoittaa markkinatilanne, jotta vaatimukset osaa asettaa oikealle tasolle. Markkinoille kannattaa myös tiedottaa tulevaisuuden tarpeista ja suunnitelmista. Suuria hankintakokonaisuuksia suositellaan pilkottavan pienempiin osiin, jotta pienet ja keskisuuret yritykset pystyvät myös osallistumaan tarjouskilpailuihin. Kannustus innovaatioiden huomioimiseen hankinnoissa on lisääntynyt myös jätehuollon alalla. Selvitettyjen kasvihuonekaasupäästöjen perusteella oli merkille pantavaa, miten suuri vaikutus polttolaitoksen valinnalla oli kasvihuonekaasupäästöihin. Oleellista onkin huomioida ympäristönäkökohdat myös energiahyötykäyttökohdetta valittaessa.

Comparative lifecycle assessment on organic and conventional carrots – case: Carrots from South-Savo and imported carrots from Italy

Organic farming is perceived to be an environmental friendly method of food production, thus assumed to be an alternative means of minimizing food-based environmental footprints. However, lower yield and unproductive years in organic crop rotation raise questions of whether it is really an environmentally friendly farming practice. Thus, the aim of this thesis was to examine the carbon footprint and energy demands of organic carrots cultivated and sold in South-Savo, Finland and compare them with those of local and imported conventional carrots using lifecycle assessment (LCA) as a method. From the investigation, it was found that organic carrots produced in South-Savo have the lowest GHG emissions and energy demand. The GHG emissions of local organic, local conventional and imported conventional carrots were found to be 4g CO2 eq. kgcarrots-1, 142g CO2 eq. kgcarrots-1 and 280 g CO2 eq. kgcarrots-1, respectively. On the other hand, energy demand for those carrots was found to be 1,33 MJ, 1,88 MJ and 3,68 MJ kgcarrots-1. Furthermore, it was also found that local organic carrots would have approximately similar GHG emissions as conventional counterpart if soil carbon stock change was excluded from the study.

Utilization of steelmaking waste materials for production of calcium carbonate (CaCO3)

The steel industry produces, besides steel, also solid mineral by-products or slags, while it emits large quantities of carbon dioxide (CO2). Slags consist of various silicates and oxides which are formed in chemical reactions between the iron ore and the fluxing agents during the high temperature processing at the steel plant. Currently, these materials are recycled in the ironmaking processes, used as aggregates in construction, or landfilled as waste. The utilization rate of the steel slags can be increased by selectively extracting components from the mineral matrix. As an example, aqueous solutions of ammonium salts such as ammonium acetate, chloride and nitrate extract calcium quite selectively already at ambient temperature and pressure conditions. After the residual solids have been separated from the solution, calcium carbonate can be precipitated by feeding a CO2 flow through the solution. Precipitated calcium carbonate (PCC) is used in different applications as a filler material. Its largest consumer is the papermaking industry, which utilizes PCC because it enhances the optical properties of paper at a relatively low cost. Traditionally, PCC is manufactured from limestone, which is first calcined to calcium oxide, then slaked with water to calcium hydroxide and finally carbonated to PCC. This process emits large amounts of CO2, mainly because of the energy-intensive calcination step. This thesis presents research work on the scale-up of the above-mentioned ammonium salt based calcium extraction and carbonation method, named Slag2PCC. Extending the scope of the earlier studies, it is now shown that the parameters which mainly affect the calcium utilization efficiency are the solid-to-liquid ratio of steel slag and the ammonium salt solvent solution during extraction, the mean diameter of the slag particles, and the slag composition, especially the fractions of total calcium, silicon, vanadium and iron as well as the fraction of free calcium oxide. Regarding extraction kinetics, slag particle size, solid-to-liquid ratio and molar concentration of the solvent solution have the largest effect on the reaction rate. Solvent solution concentrations above 1 mol/L NH4Cl cause leaching of other elements besides calcium. Some of these such as iron and manganese result in solution coloring, which can be disadvantageous for the quality of the PCC product. Based on chemical composition analysis of the produced PCC samples, however, the product quality is mainly similar as in commercial products. Increasing the novelty of the work, other important parameters related to assessment of the PCC quality, such as particle size distribution and crystal morphology are studied as well. As in traditional PCC precipitation process, the ratio of calcium and carbonate ions controls the particle shape; a higher value for [Ca2+]/[CO32-] prefers precipitation of calcite polymorph, while vaterite forms when carbon species are present in excess. The third main polymorph, aragonite, is only formed at elevated temperatures, above 40-50 °C. In general, longer precipitation times cause transformation of vaterite to calcite or aragonite, but also result in particle agglomeration. The chemical equilibrium of ammonium and calcium ions and dissolved ammonia controlling the solution pH affects the particle sizes, too. Initial pH of 12-13 during the carbonation favors nonagglomerated particles with a diameter of 1 μm and smaller, while pH values of 9-10 generate more agglomerates of 10-20 μm. As a part of the research work, these findings are implemented in demonstrationscale experimental process setups. For the first time, the Slag2PCC technology is tested in scale of ~70 liters instead of laboratory scale only. Additionally, design of a setup of several hundreds of liters is discussed. For these purposes various process units such as inclined settlers and filters for solids separation, pumps and stirrers for material transfer and mixing as well as gas feeding equipment are dimensioned and developed. Overall emissions reduction of the current industrial processes and good product quality as the main targets, based on the performed partial life cycle assessment (LCA), it is most beneficial to utilize low concentration ammonium salt solutions for the Slag2PCC process. In this manner the post-treatment of the products does not require extensive use of washing and drying equipment, otherwise increasing the CO2 emissions of the process. The low solvent concentration Slag2PCC process causes negative CO2 emissions; thus, it can be seen as a carbon capture and utilization (CCU) method, which actually reduces the anthropogenic CO2 emissions compared to the alternative of not using the technology. Even if the amount of steel slag is too small for any substantial mitigation of global warming, the process can have both financial and environmental significance for individual steel manufacturers as a means to reduce the amounts of emitted CO2 and landfilled steel slag. Alternatively, it is possible to introduce the carbon dioxide directly into the mixture of steel slag and ammonium salt solution. The process would generate a 60-75% pure calcium carbonate mixture, the remaining 25-40% consisting of the residual steel slag. This calcium-rich material could be re-used in ironmaking as a fluxing agent instead of natural limestone. Even though this process option would require less process equipment compared to the Slag2PCC process, it still needs further studies regarding the practical usefulness of the products. Nevertheless, compared to several other CO2 emission reduction methods studied around the world, the within this thesis developed and studied processes have the advantage of existing markets for the produced materials, thus giving also a financial incentive for applying the technology in practice.

Säteilysuojelu käytetyn ydinpolttoaineen kapselointi- ja loppusijoituslaitoksella

Suomen ydinenergialaki vaatii ydinenergian käytössä syntyvän ydinjätteen käsittelyn ja varastoinnin sekä loppusijoittamisen Suomeen. Fortumin ja TVO:n ydinvoimalaitoksissa syntyvä käytetty ydinpolttoaine tullaan kapseloimaan ja loppusijoittamaan Olkiluotoon rakennettavassa kapselointi- ja loppusijoituslaitoksessa. Tämän työn tavoitteena on muodostaa kokonaiskuva kapselointi- ja loppusijoituslaitoksen säteilysuojelusta aikaisemmin tehtyjen selvitysten ja suunnitelmien perusteella. Kapselointilaitoksella käytetty ydinpolttoaine suljetaan kuparikapseleihin, jotka loppusijoitetaan maan alle loppusijoituslaitoksella. Työn aluksi kuvataan loppusijoitusmenetelmä ja kapselointi- ja loppusijoituslaitoksen käyttötoiminta. Tämän jälkeen käsitellään lainsäädäntöä ja viranomaisohjeita, jotka ohjaavat ydinlaitosten säteilysuojelua. Seuraavaksi käsitellään kapselointi- ja loppusijoituslaitoksella olevia säteilylähteitä. Lisäksi työssä käsitellään kapselointi- ja loppusijoituslaitokselle suunniteltua valvonta-aluetta ja sen säteilyolosuhteiden mukaista vyöhykejakoa. Työssä saatiin tulokseksi kokonaiskuva kapselointi- ja loppusijoituslaitoksen säteilysuojelusta. Kokonaiskuvan muodostamisen lisäksi laadittiin alustavia suunnitelmia käyttötoiminnan säteilysuojelun järjestämisestä. Lisäksi laadittiin ehdotuksia valvonta-alueen tarkemmista rajoista loppusijoituslaitoksella sekä havaittiin laitosten säteilysuojeluun liittyviä ongelmia ja esitettiin ratkaisuja niihin. Ongelmaksi osoittautui muun muassa, että kapselointi- ja loppusijoituslaitoksen valvonta-alueiden luonteiden eroa ei ollut huomioitu suunnitelmissa. Lisäksi todettiin, että nykyisin ydinlaitoksilla käytössä oleva valvonta-alueen vyöhykejako ei vastaa kapselointi- ja loppusijoituslaitosten tarpeita. Näihin esitettiin ratkaisuiksi laitosten välille perustettavaa kenkärajaa ja uuden korkeamman säteilyvyöhykkeen käyttöönottoa.

Partial recovery of erythrocyte glycogen in diabetic rats treated with phenobarbital

Erythrocytes may play a role in glucose homeostasis during the postprandial period. Erythrocytes from diabetic patients are defective in glucose transport and metabolism, functions that may affect glycogen storage. Phenobarbital, a hepatic enzyme inducer, has been used in the treatment of patients with non-insulin-dependent diabetes mellitus (NIDDM), increasing the insulin-mediated glucose disposal. We studied the effects of phenobarbital treatment in vivo on glycemia and erythrocyte glycogen content in control and alloxan-diabetic rats during the postprandial period. In control rats (blood glucose, 73 to 111 mg/dl in femoral and suprahepatic veins) the erythrocyte glycogen content was 45.4 ± 1.1 and 39.1 ± 0.8 µg/g Hb (mean ± SEM, N = 4-6) in the femoral artery and vein, respectively, and 37.9 ± 1.1 in the portal vein and 47.5 ± 0.9 in the suprahepatic vein. Diabetic rats (blood glucose, 300-350 mg/dl) presented low (P<0.05) erythrocyte glycogen content, i.e., 9.6 ± 0.1 and 7.1 ± 0.7 µg/g Hb in the femoral artery and vein, respectively, and 10.0 ± 0.7 and 10.7 ± 0.5 in the portal and suprahepatic veins, respectively. After 10 days of treatment, phenobarbital (0.5 mg/ml in the drinking water) did not change blood glucose or erythrocyte glycogen content in control rats. In diabetic rats, however, it lowered (P<0.05) blood glucose in the femoral artery (from 305 ± 18 to 204 ± 45 mg/dl) and femoral vein (from 300 ± 11 to 174 ± 48 mg/dl) and suprahepatic vein (from 350 ± 10 to 174 ± 42 mg/dl), but the reduction was not sufficient for complete recovery. Phenobarbital also stimulated the glycogen synthesis, leading to a partial recovery of glycogen stores in erythrocytes. In treated rats, erythrocyte glycogen content increased to 20.7 ± 3.8 µg/g Hb in the femoral artery and 30.9 ± 0.9 µg/g Hb in the suprahepatic vein (P<0.05). These data indicate that phenobarbital activated some of the insulin-stimulated glucose metabolism steps which were depressed in diabetic erythrocytes, supporting the view that erythrocytes participate in glucose homeostasis