Axial mixing in rotating drums using magnetic resonance imaging using bran as a model for solid state fermentations

Magnetic resonance imaging (MRI) is an easily automated, reliable technique to investigate axial mixing within rotating drums. Moist bran can be clearly differentiated from dry bran using MRI allowing a non-segregating tracer for axial mixing. For a 20-cm diameter drum, the axial dispersion coefficient in the particle bed was 0.51 cm s(-2). Axial dispersion is scale-dependent.

Zeolite/rock phosphate - a novel slow release phosphorus fertiliser for potted plant production

A glasshouse study was undertaken to determine if the zeolite mineral clinoptilolite from an Australian deposit in combination with rock phosphate (RP) could significantly enhance the uptake of P by sunflowers. The zeolite/RP combination was intended to act as an exchange-fertiliser, with Ca2+ exchanging onto the zeolite in response to plant uptake of nutrient cations (NH4+ or K) enhancing the dissolution of the RP. A reactive RP (Sechura) and a relatively non-reactive RP (Duchess) were examined. Zeolite was used in Ca2+-, K+- and NH4+-saturated forms at ratios of 3.5:1 and 7:1 with RP; Ca2+-zeolite was considered the control, with exchange-induced dissolution possible from K+-and NH4+-zeolite, The zeolite/RP mixture was applied as a vertical band adjacent to the sunflower seedling. In addition, N was supplied as urea in an effort to determine if RP dissolution resulted from H+ release by nitrification. Phosphorus supply from the zeolite/RP system was compared with an available P source (KH2PO4). The experiment clearly demonstrated greatly enhanced plant uptake of P from RP when applied in combination with NH4-zeolite, though the P uptake was lower than that from the soluble P source. The zeolite/RP interaction was much more effective with the reactive R-P than the non-reactive material, Within the NH4+-zeolite/RP band, root proliferation was greatly increased, as would be expected in an exchange-fertiliser system. The K+-zeolite system did not produce a significantly greater yield than the Ca2+-zeolite control, probably because adequate K+ supply from the basal application reduced uptake within the zeolite/RP band, thus reducing the extent of exchange-induced dissolution. Nevertheless, increased root proliferation within the band was observed, implying that exchange-induced dissolution may also be possible from this system. The zeolite/RP system offers the considerable advantage of P release in response to plant demand and is unique in this regard. (C) 2002 Elsevier Science B.V. All rights reserved.

Comparison of adsorption capacity of p-Cresol & p-Nitrophenol by activated carbon in single and double solute

Adsorption of p-Cresol and p-Nitrophenol by untreated activated carbon in single and multisolute solutions was carried out at 301 K and at controlled pH conditions. In acidic conditions, well below the pK(a) of both solutes, it was observed that the adsorbate solubility and the electron density of aromatic rings influenced the extent of adsorption by affecting the extent of London dispersion forces. The fitted parameters obtained from single-solute Langmuir equation show that Q(max) and the adsorption affinity of carbon for the compound with low pK(a) decrease more significantly. In higher solution pH conditions, on the other hand, it was found that electrostatic forces played a significant role on the extent of adsorption. The presence of another compound decreases Q(max) and the adsorption affinity of carbon for the principal compound. The effect of pH, on the carbon surface and on the solute molecules, must be considered. Adsorption of the solute at higher pH values was found to be dependent on the concentration of anionic form of the solute. The isotherm data were fitted to the Langmuir isotherm equation for both single and double solute solutions.

Tree yield and fruit minerals concentrations influence 'Hass' avocado fruit quality

To investigate the variation in quality of 'Hass' avocado fruit within an orchard, fruit were harvested at commercial maturity from 15 'Hass' trees of similar appearance, growing in three adjacent rows on the same soil type, and receiving similar management. Fruit were harvested at commercial maturity, and either ripened at 22 degreesC or stored at 2 or 7 degreesC for 3 or 5 weeks and then ripened. Significant positive correlations (based, on the mean for each datum tree) were noted between fruit flesh calcium (Ca) and magnesium (Mg) concentrations and the (Ca + Mg)/potassium ratio, and the number of days for the fruit to reach the eating ripe stage (DTR). Negative correlations were also observed between these minerals and anthracnose and mesocarp discolouration (MD) severity. Negative correlations were observed between fruit potassium (K) and phosphorus (P) concentrations and DTR. Fruit from trees with high fruit yield were generally smaller, with lower anthracnose and MD severity, ripened more slowly, and had higher flesh Ca concentrations. It is likely that cultural practices that maintain moderate to high fruit yield and reduce variation in yield will improve avocado fruit quality and reduce variability in quality. Since the main differences between adjacent trees in this trial were the seedling rootstocks of unknown origin, it is suggested that rootstocks can have a significant impact on avocado yield and fruit quality. (C) 2002 Elsevier Science B.V. All rights reserved.

Distribution kinetics of solutes in the isolated in-situ perfused rat head using the multiple indicator dilution technique and a physiological two-barrier model

The purpose of this study was to determine the pharmacokinetics of [C-14]diclofenac, [C-14]salicylate and [H-3]clonidine using a single pass rat head perfusion preparation. The head was perfused with 3-[N-morpholino] propane-sulfonic acid-buffered Ringer's solution. Tc-99m-red blood cells and a drug were injected in a bolus into the internal carotid artery and collected from the posterior facial vein over 28 min. A two-barrier stochastic organ model was used to estimate the statistical moments of the solutes. Plasma, interstitial and cellular distribution volumes for the solutes ranged from 1.0 mL (diclofenac) to 1.6 mL (salicylate), 2.0 mL (diclofenac) to 4.2 mL (water) and 3.9 mL (salicylate) to 20.9 mL (diclofenac), respectively. A comparison of these volumes to water indicated some exclusion of the drugs from the interstitial space and salicylate from the cellular space. Permeability-surface area (PS) products calculated from plasma to interstitial fluid permeation clearances (CLPI) (range 0.02-0.40 mL s(-1)) and fractions of solute unbound in the perfusate were in the order: diclofenac>salicylate >clonidine>sucrose (from 41.8 to 0.10 mL s(-1)). The slow efflux of diclofenac, compared with clonidine and salicylate, may be related to its low average unbound fraction in the cells. This work accounts for the tail of disposition curves in describing pharmacokinetics in the head.

Novel composites of TiO2 (anatase) and silicate nanoparticles

Thermally stable composite nanostructures of titanium dioxide (anatase) and silicate nanoparticles were prepared from Laponite clay and a sol of titanium hydrate in the presence of poly(ethylene oxide) (PEO) surfactants. Laponite is a synthetic clay that readily disperses in water and exists as exfoliated silicate layers of about 1-nm thick in transparent dispersions of high pH. The acidic sol solution reacts with the clay platelets and leaches out most of the magnesium in the clay, while the sol particles hydrolyze further due to the high pH of the clay dispersion. As a result, larger precursors of TiO2 nanoparticles form and condense on the fragmentized pieces of the leached silicate. Introducing PEO surfactants into the synthesis can significantly increase the porosity and surface area of the composite solids. The TiO2 exists as anatase nanoparticles that are separated by silicate fragments and voids such that they are accessible to organic molecules. The size of the anatase particle can be tailored by manipulating the experimental parameters at various synthesis stages. Therefore, we can design and engineer composite nanostructures to achieve better performance. The composite solids exhibit superior properties as photocatalysts for the degradation of Rhodamine 6G in aqueous solution.

Dry matter production and allocation in Eucalyptus cloeziana and Eucalyptus argophloia seedlings in response to soil water deficits

Effects of soil water availability on seedling growth, dry matter production and allocation were determined for Gympie ( humid coastal) and Hungry Hills ( dry inland) provenances of Eucalyptus cloeziana F. Muell. and for E. argophloia Blakely ( dry inland) species. Seven-month-old seedlings were subjected to well-watered (100% field capacity, FC), moderate (70% FC) and severe (50% FC) soil water regimes in a glasshouse environment for 14 wk. There were significant differences in seedling growth, biomass production and allocation patterns between species. E. argophloia produced twice as much biomass at 100% FC, and more than three times as much at 70% and 50% FC than did either E. cloeziana provenance. Although the humid provenance of E. cloeziana had a greater leaf area at 100% FC conditions than did the dry provenance, total biomass production did not differ significantly. Both E. cloeziana provenances were highly sensitive to water deficits. E. argophloia allocated 10% more biomass to roots than did E. cloeziana. Allometric analyses indicated that relative biomass allocation patterns were significantly affected by genotype but not by soil water availability. These results have implications for taxon selection for cultivation in humid and subhumid regions.

An investigation into the possible inhibitory effects of white cypress pine (Callitris glaucophylla) litter on the germination and growth of associated ground cover species

White cypress-pine stands typically support sparse densities of shrubs and grasses. The commonly held opinion is that leaching of allelopathic chemical compounds from cypress-pine litter partly facilitates this exclusion. Germination and growth of cypress pine seedlings do not appear to be similarly affected. This study set out to determine whether cypress litter had a differential effect on germination and growth of cypress-pine seedlings and on associated ground-cover species. Glasshouse trials comparing seedling emergence under cypress- and artificial-litter layers were undertaken. Cypress-pine litter did not have an inhibitory effect on the germination or growth of ground-cover species. In most cases, seedling emergence was facilitated by the application of cypress-pine litter due to its ability to increase the water holding capacity of the underlying soil. Cypress litter did not promote growth of its own seedlings over its competitors except on coarse-textured soils where it provided an ameliorative function to water stress due to the soil's reduced water holding capacity. The inhibition of ground-cover species' germination and growth in pure cypress stands was suggested to be the result of high below-ground resource competition due to the pine's expansive root morphology.

Rootstocks influence 'Hass' avocado fruit quality and fruit minerals

To determine the potential for rootstocks to improve avocado quality, 'Hass' fruit from trees on seedling 'Velvick' (SV), clonal 'Velvick' (CV) or clonal 'Duke 7' (CD) rootstocks were harvested in 1999 and 2000, ripened at 20 C immediately after harvest (non-stored) or stored at 5 C for four weeks (stored), and then fruit quality and mineral concentrations determined. In 2000, non-stored CV fruit had lower severity of body rots (5% of flesh volume affected, caused mainly by Colletotrichum gloeosporioides) than CD fruit (20%), while body rots severity in stored CV fruit was 20% compared with 38% in stored CD fruit. Stored CV fruit had less severe diffuse discoloration (3% and 9% in 1999 and 2000, respectively) than CD fruit (7% and 20%, respectively). Stored CV fruit also had less severe vascular browning (19%) than CD fruit (33%) in 2000. In both seasons, CV fruit had 15-19% higher flesh calcium concentrations, 17-22% higher flesh boron concentrations, and 14-15% lower flesh nitrogen concentrations than CD fruit. In 2000, CV fruit also had 27% more skin calcium and 14% less skin nitrogen than CD fruit. There were no effects of rootstock on yield, canopy volume, measured length of non-suberized roots, average fruit weight, fruit length: width ratio, skin thickness, dry matter, proportion of the fruit skin purple-black when ripe, or seed mass: fruit weight ratio. These results suggest that there is potential to improve 'Hass' avocado quality through rootstock selection, and that tree and fruit mineral concentrations have a role in this relationship.

Ultrasonic absorption in polymer gel dosimeters

Ultrasonic absorption in polymer gel dosimeters was investigated. An ultrasonic interferometer was used to study the frequency (f) dependence of the absorption coefficient (alpha) in a polyacrylamide gel dosimeter (PAG) in the frequency range 5-20 MHz. The frequency dependence of ultrasonic absorption deviated from that of an ideal viscous fluid. The presence of relaxation mechanisms was evidenced by the frequency dependence of alpha/f(2) and the dispersion in ultrasonic velocity. It was concluded that absorption in polymer gel dosimeters is due to a number of relaxation processes which may include polymer-solvent interactions as well as relaxation due to motion of polymer side groups. The dependence of ultrasonic absorption on absorbed dose and formulation was also investigated in polymer gel dosimeters as a function of pH and chemical composition. Changes in dosimeter pH and chemical composition resulted in a variation in ultrasonic dose response curves. The observed dependence on pH was considered to be due to pH induced modifications in the radiation yield while changes in chemical composition resulted in differences in polymerisation kinetics. (C) 2003 Elsevier B.V. All rights reserved.

Fatty acid binding protein is a major determinant of hepatic pharmacokinetics of palmitate and its metabolites

Disposition kinetics of [H-3] palmitate and its low-molecular-weight metabolites in perfused rat livers were studied using the multiple-indicator dilution technique, a selective assay for [H-3] palmitate and its low-molecular-weight metabolites, and several physiologically based pharmacokinetic models. The level of liver fatty acid binding protein (L-FABP), other intrahepatic binding proteins (microsomal protein, albumin, and glutathione S-transferase) and the outflow profiles of [H-3] palmitate and metabolites were measured in four experimentalgroups of rats: 1) males; 2) clofibrate-treated males; 3) females; and 4) pregnant females. A slow-diffusion/bound model was found to better describe the hepatic disposition of unchanged [H-3] palmitate than other pharmacokinetic models. The L-FABP levels followed the order: pregnant female > clofibrate-treated male > female > male. Levels of other intrahepatic proteins did not differ significantly. The hepatic extraction ratio and mean transit time for unchanged palmitate, as well as the production of low-molecular-weight metabolites of palmitate and their retention in the liver, increased with increasing L-FABP levels. Palmitate metabolic clearance, permeability-surface area product, retention of palmitate by the liver, and cytoplasmic diffusion constant for unchanged [H-3] palmitate also increased with increasing L-FABP levels. It is concluded that the variability in hepatic pharmacokinetics of unchanged [H-3] palmitate and its low-molecular-weight metabolites in perfused rat livers is related to levels of L-FABP and not those of other intrahepatic proteins.

On measuring quality of a probabilistic commodity forecast for a system that incorporates seasonal climate forecasts

Regional commodity forecasts are being used increasingly in agricultural industries to enhance their risk management and decision-making processes. These commodity forecasts are probabilistic in nature and are often integrated with a seasonal climate forecast system. The climate forecast system is based on a subset of analogue years drawn from the full climatological distribution. In this study we sought to measure forecast quality for such an integrated system. We investigated the quality of a commodity (i.e. wheat and sugar) forecast based on a subset of analogue years in relation to a standard reference forecast based on the full climatological set. We derived three key dimensions of forecast quality for such probabilistic forecasts: reliability, distribution shift, and change in dispersion. A measure of reliability was required to ensure no bias in the forecast distribution. This was assessed via the slope of the reliability plot, which was derived from examination of probability levels of forecasts and associated frequencies of realizations. The other two dimensions related to changes in features of the forecast distribution relative to the reference distribution. The relationship of 13 published accuracy/skill measures to these dimensions of forecast quality was assessed using principal component analysis in case studies of commodity forecasting using seasonal climate forecasting for the wheat and sugar industries in Australia. There were two orthogonal dimensions of forecast quality: one associated with distribution shift relative to the reference distribution and the other associated with relative distribution dispersion. Although the conventional quality measures aligned with these dimensions, none measured both adequately. We conclude that a multi-dimensional approach to assessment of forecast quality is required and that simple measures of reliability, distribution shift, and change in dispersion provide a means for such assessment. The analysis presented was also relevant to measuring quality of probabilistic seasonal climate forecasting systems. The importance of retaining a focus on the probabilistic nature of the forecast and avoiding simplifying, but erroneous, distortions was discussed in relation to applying this new forecast quality assessment paradigm to seasonal climate forecasts. Copyright (K) 2003 Royal Meteorological Society.

A review of drainage and spontaneous rupture in free standing thin films with tangentially immobile interfaces

A review of spontaneous rupture in thin films with tangentially immobile interfaces is presented that emphasizes the theoretical developments of film drainage and corrugation growth through the linearization of lubrication theory in a cylindrical geometry. Spontaneous rupture occurs when corrugations from adjacent interfaces become unstable and grow to a critical thickness. A corrugated interface is composed of a number of waveforms and each waveform becomes unstable at a unique transition thickness. The onset of instability occurs at the maximum transition thickness, and it is shown that only upper and lower bounds of this thickness can be predicted from linear stability analysis. The upper bound is equivalent to the Freakel criterion and is obtained from the zeroth order approximation of the H-3 term in the evolution equation. This criterion is determined solely by the film radius, interfacial tension and Hamaker constant. The lower bound is obtained from the first order approximation of the H-3 term in the evolution equation and is dependent on the film thinning velocity A semi-empirical equation, referred to as the MTR equation, is obtained by combining the drainage theory of Manev et al. [J. Dispersion Sci. Technol., 18 (1997) 769] and the experimental measurements of Radoev et al. [J. Colloid Interface Sci. 95 (1983) 254] and is shown to provide accurate predictions of film thinning velocity near the critical thickness of rupture. The MTR equation permits the prediction of the lower bound of the maximum transition thickness based entirely on film radius, Plateau border radius, interfacial tension, temperature and Hamaker constant. The MTR equation extrapolates to Reynolds equation under conditions when the Plateau border pressure is small, which provides a lower bound for the maximum transition thickness that is equivalent to the criterion of Gumerman and Homsy [Chem. Eng. Commun. 2 (1975) 27]. The relative accuracy of either bound is thought to be dependent on the amplitude of the hydrodynamic corrugations, and a semiempirical correlation is also obtained that permits the amplitude to be calculated as a function of the upper and lower bound of the maximum transition thickness. The relationship between the evolving theoretical developments is demonstrated by three film thickness master curves, which reduce to simple analytical expressions under limiting conditions when the drainage pressure drop is controlled by either the Plateau border capillary pressure or the van der Waals disjoining pressure. The master curves simplify solution of the various theoretical predictions enormously over the entire range of the linear approximation. Finally, it is shown that when the Frenkel criterion is used to assess film stability, recent studies reach conclusions that are contrary to the relevance of spontaneous rupture as a cell-opening mechanism in foams. (C) 2003 Elsevier Science B.V. All rights reserved.

Modelagem da dispersão de odores em ambientes urbanos

O presente trabalho investigou o problema da modelagem da dispersão de compostos odorantes em presença de obstáculos (cúbicos e com forma complexa) sob condição de estabilidade atmosférica neutra. Foi empregada modelagem numérica baseada nas equações de transporte (CFD1) bem como em modelos algébricos baseados na pluma Gausseana (AERMOD2, CALPUFF3 e FPM4). Para a validação dos resultados dos modelos e a avaliação do seu desempenho foram empregados dados de experimentos em túnel de vento e em campo. A fim de incluir os efeitos da turbulência atmosférica na dispersão, dois diferentes modelos de sub-malha associados à Simulação das Grandes Escalas (LES5) foram investigados (Smagorinsky dinâmico e WALE6) e, para a inclusão dos efeitos de obstáculos na dispersão nos modelos Gausseanos, foi empregado o modelo PRIME7. O uso do PRIME também foi proposto para o FPM como uma inovação. De forma geral, os resultados indicam que o uso de CFD/LES é uma ferramenta útil para a investigação da dispersão e o impacto de compostos odorantes em presença de obstáculos e também para desenvolvimento dos modelos Gausseanos. Os resultados também indicam que o modelo FPM proposto, com a inclusão dos efeitos do obstáculo baseado no PRIME também é uma ferramenta muito útil em modelagem da dispersão de odores devido à sua simplicidade e fácil configuração quando comparado a modelos mais complexos como CFD e mesmo os modelos regulatórios AERMOD e CALPUFF. A grande vantagem do FPM é a possibilidade de estimar-se o fator de intermitência e a relação pico-média (P/M), parâmetros úteis para a avaliação do impacto de odores. Os resultados obtidos no presente trabalho indicam que a determinação dos parâmetros de dispersão para os segmentos de pluma, bem como os parâmetros de tempo longo nas proximidades da fonte e do obstáculo no modelo FPM pode ser melhorada e simulações CFD podem ser usadas como uma ferramenta de desenvolvimento para este propósito. Palavras chave: controle de odor, dispersão, fluidodinâmica computacional, modelagem matemática, modelagem gaussiana de pluma flutuante, simulação de grandes vórtices (LES).

Estudo da camada limite atmosférica em regiões metropolitanas costeiras com simulações de brisa marítima

O principal objetivo deste trabalho foi identificar e caracterizar a evolução diária da Camada Limite Atmosférica (CLA) na Região da Grande Vitória (RGV), Estado do Espírito Santo, Brasil e na Região de Dunkerque (RD), Departamento Nord Pas-de-Calais, França, avaliando a acurácia de parametrizações usadas no modelo meteorológico Weather Research and Forecasting (WRF) em detectar a formação e atributos da Camada Limite Interna (CLI) que é formada pelas brisas marítimas. A RGV tem relevo complexo, em uma região costeira de topografia acidentada e uma cadeia de montanhas paralela à costa. A RD tem relevo simples, em uma região costeira com pequenas ondulações que não chegam a ultrapassar 150 metros, ao longo do domínio de estudos. Para avaliar os resultados dos prognósticos feitos pelo modelo, foram utilizados os resultados de duas campanhas: uma realizada na cidade de Dunkerque, no norte da França, em Julho de 2009, utilizando um sistema light detection and ranging (LIDAR), um sonic detection and ranging (SODAR) e dados de uma estação meteorológica de superfície (EMS); outra realizada na cidade de Vitória – Espírito Santo, no mês de julho de 2012, também usando um LIDAR, um SODAR e dados de uma EMS. Foram realizadas simulações usando três esquemas de parametrizações para a CLA, dois de fechamento não local, Yonsei University (YSU) e Asymmetric Convective Model 2 (ACM2) e um de fechamento local, Mellor Yamada Janjic (MYJ) e dois esquemas de camada superficial do solo (CLS), Rapid Update Cycle (RUC) e Noah. Tanto para a RGV quanto para a RD, foram feitas simulações com as seis possíveis combinações das três parametrizações de CLA e as duas de CLS, para os períodos em que foram feitas as campanhas, usando quatro domínios aninhados, sendo os três maiores quadrados com dimensões laterais de 1863 km, 891 km e 297 km, grades de 27 km, 9 km e 3 km, respectivamente, e o domínio de estudo, com dimensões de 81 km na direção Norte-Sul e 63 km na Leste-Oeste, grade de 1 km, com 55 níveis verticais, até um máximo de, aproximadamente, 13.400 m, mais concentrados próximos ao solo. Os resultados deste trabalho mostraram que: a) dependendo da configuração adotada, o esforço computacional pode aumentar demasiadamente, sem que ocorra um grande aumento na acurácia dos resultados; b) para a RD, a simulação usando o conjunto de parametrizações MYJ para a CLA com a parametrização Noah produziu a melhor estimativa captando os fenômenos da CLI. As simulações usando as parametrizações ACM2 e YSU inferiram a entrada da brisa com atraso de até três horas; c) para a RGV, a simulação que usou as parametrizações YSU para a CLA em conjunto com a parametrização Noah para CLS foi a que conseguiu fazer melhores inferências sobre a CLI. Esses resultados sugerem a necessidade de avaliações prévias do esforço computacional necessário para determinadas configurações, e sobre a acurácia de conjuntos de parametrizações específicos para cada região pesquisada. As diferenças estão associadas com a capacidade das diferentes parametrizações em captar as informações superficiais provenientes das informações globais, essenciais para determinar a intensidade de mistura turbulenta vertical e temperatura superficial do solo, sugerindo que uma melhor representação do uso de solo é fundamental para melhorar as estimativas sobre a CLI e demais parâmetros usados por modelos de dispersão de poluentes atmosféricos.