Surface morphology and optical property of 1.3 mu m In0.5Ga0.5As/GaAs self-organized quantum dots grown by MBE

Surface morphology and optical properties of 1.3 mum self-organized InGaAs/GaAs quantum dots structure grown by molecular beam epitaxy have been investigated by atomic force microscopy and photoluminescence measurements. It has been shown that the surface morphology evolution and emission wavelengths of InGaAs/GaAs QDs can be controlled effectively via cycled monolayer deposition methods due to the reduction of the surface strain. Our results provide important information for optimizing the epitaxial parameters for obtaining 1.3 mum long wavelength emission quantum dots structures. (C) 2002 Elsevier Science B.V. All rights reserved.

A method to obtain ground state electroluminescence from 1.3 mu m emitting InAs/GaAs quantum dots grown by molecular beam epitaxy

1.3 mum emitting InAs/GaAs quantum dots (QDs) have been grown by molecular beam epitaxy and QD light emitting diodes (LEDs) have been fabricated. In the electroluminescence spectra of QD LEDs, two clear peaks corresponding to the ground state emission and the excited state emission are observed. It was found that the ground state emission could be achieved by increasing the number of QDs contained in the active region because of the state filling effect. This work demonstrates a way to control and tune the emitting wavelength of QD LEDs and lasers.

Atomic hydrogen induced step bunching and fabrication of quantum wire arrays on GaAs (311)A substrate by molecular beam epitaxy

Atomic hydrogen assisted molecular beam epitaxy (MBE) is a novel type of epitaxial growth of nanostructures. The GaAs (311)A surface naturally forms one-dimensional step arrays by step bunching along the direction of (-233) and the space period is around 40nm. The step arrays extend over several mum without displacement. The InGaAs quantum wire arrays are grown on the step arrays as the basis. Our results may prompt further development of more uniform quantum wire and quantum dot arrays.

A direct-conversion mixer with a DC-offset cancellation for WLAN

This paper presents a 5GHz double-balanced mixer with DC-offset cancellation circuit for direct-conversion receiver compliant with IEEE 802.11a wireless LAN standard. The analog feedback loop is used, to eliminate the DC-offset at the output of the double-balanced mixer. The test results show that the mixer with DC-offset cancellation circuit has voltage conversion gain of 9.5dB at 5.15GHz, noise figure of 13.5dB, IIP3 of 7.6 dBm, 1.73mV DC-offset voltage and 67mW power with 3.3-V power supply. The DC-offset cancellation circuit has less than 0.1mm(2) additional area and 0.3mW added power dissipation. The direct conversion WLAN receiver has been implemented in a 0.35 mu m SiGe BiCMOS technology.

Correlation Between Lattice Strain and Energy Gap Bowing of AlxGa1-xN Epitaxial Thin Films

The correlation between the energy band-gap of AlxGa1-xN epitaxial thin films and lattice strain was investigated using both High Resolution X-ray Diffraction (HRXRD) and Spectroscopic Ellipsometry (SE). The Al fraction, lattice relaxation, and elastic lattice strain were determined for all AlxGa1-xN epilayers, and the energy gap as well. Given the type of intermediate layer, a correlation trend was found between energy band-gap bowing parameter and lattice mismatch, the higher the lattice mismatch is, the smaller the bowing parameter (b) will be.

A New Technique for Side Pumping of Double-Clad Fiber Lasers

We report a new technique, called SAP, for side pumping of double-clad, rare-earth-doped fiber lasers using fiber-coupled pump sources. The highest coupling efficiency can even exceed 92% in theory with this structure.

A direct-conversion mixer with DC-offset cancellation for IEEE 802.11a WLAN receiver

A DC-offset cancellation scheme in the 5GHz direct-conversion receiver compliant with IEEE 802.11a wireless LAN standard is described in this paper. It uses the analog feedback loop to eliminate the DC-offset at the output of the double-balanced mixer. The mixer has a simulation voltage conversion gain of IMB at 5.2GHz, noise figure of 9.67dB, IIP3 of 7.6dBm. The solution provides 39.1dB reduction according to the leakage value at LO and mixer load resistors, the additional noise figure added to mixer is less than 0.9dB, the added power dissipation is 0.1mW and was fabricated in 60GHz 0.35 mu m SiGe BiCMOS technology.

An analysis and simulation about conditioned launch for very short reach (VSR-4)

VSR4 links use graded index multimode fibers (GIMMFs) as the transmission medium with operation wavelength 850nm. For cost reasons, VCSEL has been selected as the optical source to VSR4. The minimum bandwidth specification for 62.5um GIMMF in VSR4 is only 400 MHz(.)km for over-filled-launch (OFL) condition. The distance of 300 meters is limited over transmission rates of 1.25Gbit/s on the basis of this specification. In order to overcome the OFL bandwidth limit by selective excitation of a limited number of modes, conditioned launch technique is investigated. In this paper, based on a comprehensive dispersion theory of GIMMF, a model is built to simulate the transmission of optical signal in GIMMFs and a comparison between OFL and conditioned launch is analyzed. The result can be the guidelines for the best choice of techniques for various LAN and interconnect systems also.

Photovoltaic effect of tin disulfide with nanocrystalline/amorphous blended phases

Tin disulfide (SnS2) nanocrystalline/amorphous blended phases were synthesized by mild chemical reaction. Both X-ray diffraction and transmission electron microscopy measurements demonstrate that the as-synthesized particles presented very small size, with a diameter of only a few nanometers. The photoluminescence (PL) spectrum suggests efficient splitting of photo-generated excitons in poly[2-methoxy-5-(3',7'-dimethyloctyloxy)-1,4-phenylenevinylene] (MDMO-PPV) and SnS2 hybrid films. Organic/inorganic hybrid solar cells comprising MDMO-PPV and SnS2 were prepared, giving photovoltage, photocurrent, fill factor and efficiency values of 0.702 V, 0.549 mA/cm(2), 0.385 and 0.148%, respectively, which suggests that this phase-blended inorganic semiconductor can also serve as a promising solar energy material. (C) 2009 Elsevier Ltd. All rights reserved.

Influence of interface modification on the performance of polymer/Bi2S3 nanorods bulk heterojunction solar cells

In this paper, bulk heterojunction photovoltaic devices based on the poly[2-methoxy-5-(3',7'-dimethyloctyloxy)- 1,4-phenylenevinylene] (MDMO-PPV):Bi2S3 nanorods hybrid material were present. To optimize the performance of the devices, the interface modification of the hybrid material that has a significant impact on the exciton dissociation efficiency was studied. An improvement in the device performance was achieved by modifying the Bi2S3 surface with a thin dye layer. Moreover, modifying the Bi2S3 surface with anthracene-9-carboxylic acid can enhance the performance further. Compared with the solar cells with Bi2S3 nanorods hybrid with the MDMO-PPV as the active layer, the anthracene-9carboxylic acid modified devices are better in performance, with the power conversion efficiency higher by about one order in magnitude.

无线局域网的Web缓存系统研究

由于无线环境中的网络和手持设备的限制,缓存机制在提高移动系统性能方面发挥着重要作用。本文描述了适用于无线LAN的Web缓存系统EasyCache系统的实现,给出了基于数据挖掘理论的移动主机端缓存数据预取算法SEDP。模拟实验数据表明SEDP算法取得了良好的效果。

应用软件发布与恢复机制研究

在传统的软件开发过程中，开发者更关注软件开发生命周期的管理，而对软 件开发后生命周期的管理并不热心。随着信息技术和互联网技术的快速发展，软 件产业发生了重大变革。新的软件运营模式要求对软件开发后生命周期管理提供 完善的支持。 本文首先回顾了传统的软件发布技术。PXE技术提供了网络远程引导功能， 该技术结合网络远程唤醒技术Wake-on-LAN使得通过网络远程控制客户机安装 操作系统成为可能。网络安装软件有基于网络克隆的Symantec Ghost和Windows Server 2003 RIS；有基于脚本的Kickstart；有基于镜像的SystemImager suite。在 开源系统中，APT是最为著名的包管理工具，它较为完善地解决了软件包之间的 依赖关系。网络更新技术则提供了更多的功能，目前的更新软件有：通用产品更 新器Install Shield, Power Update, Software Dock, Marimba等；以及供应商产品更 新器Microsoft Update, Windows Update, Microsoft SUS, Microsoft SMS, Norton AntiVirus LiveUpate等。 美国Colorado大学为软件开发后生命周期建立了一个体系结构Software Dock，并实现了一个粗略的原型系统。本研究侧重分析了应用软件的发布和恢 复机制，提出以用户的角度看待软件开发后生命周期管理的思想，建立了一个软 件发布机制体系结构，试图解决如下问题：系统重装后的运行态恢复，即系统崩 溃后如何快速而灵活地恢复到指定状态点并且重建该状态点的运行状态(即运行 态恢复)；应用软件恢复透明化和即点即用。

Characteristic of the ultrawideband electromagnetic radiation generated by PCSS

A novel ultra-wideband electromagnetic pulse generating method based on the photoconductive semiconductor switches (PCSS) is presented. Gallium arsenide is used to develop the PCSS for an ultrashort electromagnetic pulse source. The pulse generated by such PCSS is within picosecond (ps) time scale, and can yield power pulse with an voltage over 10 kV. The experimental results show that the pulses are stable, with the peak-peak amplitude change of 6% and the time jitter within several picoseconds. The radiations of the PCSS triggered by the picosecond laser and fenitosecond laser pulse series illustrate that the electromagnetic pulses would have high repetition of more than 80 MHz and frequency bandwidth of DC-6 GHz. The radiations of "lock-on " mode of the PCSS are also analyzed here. (c) 2007 Wiley Periodicals, Inc.

Picosecond ultra-wideband short pulse radiated by antenna arrays

This report presents the experiments to study the characteristics of the picosecond ultra-wideband pulses coherent radiation. The testing involves bow-tie horn antennas for both the transninting and receiving antenna. Sixteen channels of electrical pulses with 290 ps duration and jitter < 30 ps have been used. The antenna arrays with various frames of 4 x 1, 4 x 2, 4 x 3, 4 x 4 are employed to radiate the pulses. The receiving antenna measures the electrical field in different distance front the transmitting antennas arrant The results show that if the pulses are in coherent condition, the peak power pulse of output by antennas array with N elements are N-2 of that of the single element antenna. (c) 2007 Wiley Periodicals, Inc.