Simulation of hydrogen peroxide direct synthesis in a microreactor

A set of models in Aspen plus was built to simulate the direct synthesis process of hydrogen peroxide in a micro-reactor system. This process model can be used to carry out material balance calculation under various experimental conditions. Three thermodynamic property methods were compared by calculating gas solubility and Uniquac-RK method was finally selected for process model. Two different operation modes with corresponding operation conditions were proposed as the starting point of future experiments. Simulations for these two modes were carried out to get the information of material streams. Moreover, some hydrodynamic parameters such as gas/liquid superficial velocity, gas holdup were also calculated with improved process model. These parameters proved the proposed experimental conditions reasonable to some extent. The influence of operation conditions including temperature, pressure and circulation ratio was analyzed for the first operation mode, where pure oxygen was fed into dissolving tank and hydrogen-carbon dioxide mixture was fed into microreactor directly. The preferred operation conditions for the system are low temperature (2°C) and high pressure (30 bar) in dissolving tank. High circulation ratio might be good in the sense that more oxygen could be dissolved and fed into reactor for reactions, but meanwhile hydrodynamics of microreactor should be considered. Furthermore, more operation conditions of reactor gas/liquid feeds in both of two operation modes were proposed to provide guidance for future experiment design and corresponding hydrodynamic parameters were also calculated. Finally, safety issue was considered from thermodynamic point of view and there is no explosion danger at given experimental plan since the released reaction heat will not cause solvent vaporization inside the microchannels. The improvement of process model still needs further study based on the future experimental results.

Adsorptive removal of harmful organic compound from aqueous solutions

Adsorption is one of the most commonly used methods in water treatment processes. It is attractive due to it easy operation and the availability of a wide variety of commercial adsorbents. This doctoral thesis focuses on investigating and explaining the influence of external phase conditions (temperature, pH, ionic strength, acidity, presence of cosolutes) on adsorption phenomena. In order to cover a wide range of factors and phenomena, case studies were chosen from various fields where adsorption is applied. These include the adsorptive removal of surface active agents (used in cleaning chemicals, for example) from aqueous effluents, the removal of hormones (estradiol) from drinking water, and the adsorption of antibiotics onto silica. The latter can beused to predict the diffusion of antibiotics in the aquatic system if they are released into the environment. Also the adsorption of living cells on functionalized polymers to purify infected water streams was studied. In addition to these examples, the adsorptive separation of harmful compounds from internal water streams within a chemical process was investigated. The model system was removal of fermentation inhibitors from lignocelluloses hydrolyzates. The detoxification of the fermentation broth is an important step in the manufacture of bioethanol from wood, but has not been studied previously in connection with concentrated acid hydrolyzates. New knowledge on adsorption phenomena was generated for all of the applications investigated. In most cases, the results could be explained by combining classical theories for individual phenomena. As an example, it was demonstrated how liquid phase aggregation could explain abnormal-looking adsorption equilibrium data. In addition to the fundamental phenomena, also process performance was of interest. This aspect is often neglected in adsorption studies. It was demonstrated that adsorbents should not be selected for a target application based on their adsorption properties only, but regeneration of the spent adsorbent must be considered. It was found that using a suitable amount of organic co-solvent in the regeneration can significantly improve the productivity of the process.

Recovery of carboxylic acids from aqueous solutions

Carboxylic acids are commonly used organic acids and have many applications in industries producing food and pharmaceutical products, surfactants and detergents. Especially formic, acetic, propionic and butyric acid are important organic chemicals. These compounds can be found in many side streams and plant effluents. Recovery costs of carboxylic acids are high when they are removed from dilute solution. Conventional processes for the recovery of carboxylic acids from aqueous solutions are classical distillation or extractive distillation, azeotropic distillation or liquid-liquid extraction. The literature part of this Master’s of Science Thesis comprises possible extractants in liquid-liquid extraction of carboxylic acids from aqueous solutions and methods for their regeneration form the extract. The experimental part of this Thesis investigates liquid-liquid extraction of carboxylic acids from aqueous solutions. The aim of this work was to find a suitable extractant for liquid-liquid extraction and suitable process conditions to recover carboxylic acids from aqueous solutions. Also, back extraction of carboxylic acids and their thermal decomposition in relation to distillation of were. Experiments showed that there is more than one possible extractant for liquid-liquid extraction of carboxylic acids. Results also showed that it is possible to separate carboxylic acids and regenerate all the used extractants by vacuum distillation at suitable temperature.

Future revenue models: Transformation from textbooks to digital solutions in the educational publishing industry, Case Sanoma Learning

This study was conducted in order to learn how companies’ revenue models will be transformed due to the digitalisation of its products and processes. Because there is still only a limited number of researches focusing solely on revenue models, and particularly on the revenue model change caused by the changes at the business environment, the topic was initially approached through the business model concept, which organises the different value creating operations and resources at a company in order to create profitable revenue streams. This was used as the base for constructing the theoretical framework for this study, used to collect and analyse the information. The empirical section is based on a qualitative study approach and multiple-case analysis of companies operating in learning materials publishing industry. Their operations are compared with companies operating in other industries, which have undergone comparable transformation, in order to recognise either similarities or contrasts between the cases. The sources of evidence are a literature review to find the essential dimensions researched earlier, and interviews 29 of managers and executives at 17 organisations representing six industries. Based onto the earlier literature and the empirical findings of this study, the change of the revenue model is linked with the change of the other dimen-sions of the business model. When one dimension will be altered, as well the other should be adjusted accordingly. At the case companies the transformation is observed as the utilisation of several revenue models simultaneously and the revenue creation processes becoming more complex.

Ammoniumkloridi Porvoon ja Naantalin jalostamoiden vetyverkoissa

Tässä työssä on käsitelty ammoniumkloridia Porvoon ja Naantalin jalostamoiden vetyverkoissa. Tietoa ammoniumkloridin aiheuttamista ongelmista ja niihin vaikuttavista tekijöistä on kerätty ja niiden pohjalta on pyritty löytämään keinoja, joilla ongelmaa voidaan vähentää tai poistaa. Kirjallisuusosassa on käsitelty ammoniumkloridia, sen aiheuttamaa korroosiota ja materiaalien ammoniumkloridikestävyyttä. Lisäksi kirjallisuusosassa on käsitelty ammoniumkloridin muodostumiseen tarvittavan vetykloridin määritysmenetelmiä sekä ammonium- ja kloridi-ionien määritysmenetelmiä. Työn soveltavassa osassa kerättiin tietoa ammoniumkloridin aiheuttamista ongelmista ja ammoniumkloridin muodostumiseen vaikuttavista tekijöistä. Lisäksi Porvoon jalostamolla suoritettiin mittauksia, joilla määritettiin ammoniakki- ja vetykloridipitoisuuksia vetyvirroista. Tulosten perusteella saatiin käsitys jalostamon ammoniumkloridiongelman nykytilanteesta ja tutkittiin ammoniumkloridia muodostavien ammoniakin ja vetykloridin lähteitä. Lisäksi keinoja vähentää ammoniumkloridin muodostumista tunnistettiin.

Waste Stream Investigation from Perspective of Changing Waste Legislation at Green Sand Foundries

The update of the Finnish legislation concerning waste was unavoidable, to comply with the European Union (EU) requirements defined in the EU-Directive on Waste. The new waste law updates were enacted into the Finnish legislation on the 11.03.2011 and targeted for applicability by the 11.03.2012. This thesis investigates the implications of the new amendments to the waste legislation from the perspective of green sand foundries. The investigations are conducted by comparing two of Componenta’s green sand foundries and evaluating their waste streams. Additionally, the impacts of legislation amendments are critiqued on their environmental and economic aspects. The study’s comparison of waste fractions at the two foundries reveals that sand is dominant in absolute tonnage and costs. The increments of waste taxes forces foundries to focus on waste management, recycling and disposing. The new legislation’s promotion of material efficiency, also guides foundries towards the prevention of waste. A potential preventive measure is to regenerate waste sand resulting to cost savings on both raw-materials and waste management. However, the lack of absolute targets for waste prevention or recycling rates discourages the interests towards creating or adopting new technologies and methods for the waste handling.

Harvinaisten metallien talteenotto epäorgaanisista jätevirroista

Taloudellisesti tärkeiden metallien varannot ja tuotanto eivät ole jakautuneet tasaisesti. Maantieteelliset alueet, joilla ei ole omia varantoja ovat riippuvaisia muualta tuoduista raaka-aineista. Euroopan komissio ja USA:n energiaministeriö ovat luokitelleet tietyt metallit kriittisiksi niiden taloudellisen merkittävyyden ja saatavuuteen liittyvien epävarmuustekijöiden johdosta. Tällaisten metallien saatavuutta voitaisiin mahdollisesti parantaa lisäämällä niiden talteenottoa jätteistä. Tutkimuksessa kartoitettiin Euroopan komission kriittiseksi luokittelemien metallien pitoisuuksia eräissä jätevirroissa. Kartoitetut jätteet olivat teollisissa poltto-prosesseissa syntyneitä polttojätteitä, prosessiteollisuuden jätesakkoja ja sähkö- ja elektroniikkajätteitä. Kartoituksen perusteella valittiin lupaavimmat jätteet ja suoritettiin niille talteenottokokeita. Talteenottokokeita suoritettiin kolmelle jätteelle. Yhdestä jätesakasta liuotettiin indiumia rikki- ja suolahapoilla. Kahden eri polttojätteen seoksesta liuotettiin galliumia rikkihapolla. Käytettyjen loisteputkien käsittelyprosessista peräisin olleesta sakasta liuotettiin maametalleja rikki- ja suolahapoilla sekä rikki- ja typpihapon seoksella. Indium liukeni heikosti (korkeintaan 25 %) huoneenlämmössä rikkihapolla. Suolahapolla se liukeni paremmin (68 %). Polttojätteen liuotuskokeissa galliumin talteenottoasteen todettiin riippuvan käytetyn liuottimen määrästä. Loisteputkijätesakasta liukeni yttriumia ja europiumia kaikilla käytetyillä happoliuoksilla noin 70–100 %. Käytetyillä happokonsentraatioilla ei havaittu suuria eroja yttriumin ja europiumin liukoisuuksissa. Näitä metalleja voitaisiin mahdollisesti ottaa talteen tämän tyyppisestä sakasta liuottamalla ne happoliuoksella ja saostamalla oksalaattina. Tarvittaessa liuokset voitaisiin puhdistaa tai metallit erottaa toisistaan neste–nesteuutolla, joka on tärkein maametallien tuotantoon käytetty hydrometallurginen menetelmä.

Identification of extractives and polysaccharides as foulants in membrane filtration of pulp and paper mill effluents

The search for new renewable materials has intensified in recent years. Pulp and paper mill process streams contain a number of potential compounds which could be used in biofuel production and as raw materials in the chemical, food and pharmaceutical industries. Prior to utilization, these compounds require separation from other compounds present in the process stream. One feasible separation technique is membrane filtration but to some extent, fouling still limits its implementation in pulp and paper mill applications. To mitigate fouling and its effects, foulants and their fouling mechanisms need to be well understood. This thesis evaluates fouling in filtration of pulp and paper mill process streams by means of polysaccharide model substance filtrations and by development of a procedure to analyze and identify potential foulants, i.e. wood extractives and carbohydrates, from fouled membranes. The model solution filtration results demonstrate that each polysaccharide has its own fouling mechanism, which also depends on the membrane characteristics. Polysaccharides may foul the membranes by adsorption and/or by gel/cake layer formation on the membrane surface. Moreover, the polysaccharides interact, which makes fouling evaluation of certain compound groups very challenging. Novel methods to identify wood extractive and polysaccharide foulants are developed in this thesis. The results show that it is possible to extract and identify wood extractives from membranes fouled in filtration of pulp and paper millstreams. The most effective solvent was found to be acetone:water (9:1 v/v) because it extracted both lipophilic extractives and lignans at high amounts from the fouled membranes and it was also non-destructive for the membrane materials. One hour of extraction was enough to extract wood extractives at high amounts for membrane samples with an area of 0.008 m2. If only qualitative knowledge of wood extractives is needed a simplified extraction procedure can be used. Adsorption was the main fouling mechanism in extractives-induced fouling and dissolved fatty and resin acids were mostly the reason for the fouling; colloidal fouling was negligible. Both process water and membrane characteristics affected extractives-induced fouling. In general, the more hydrophilic regenerated cellulose (RC) membrane fouled less that the more hydrophobic polyethersulfone (PES) and polyamide (PA) membranes independent of the process water used. Monosaccharide and uronic acid units could also be identified from the fouled synthetic polymeric membranes. It was impossible to analyze all monosaccharide units from the RC membrane because the analysis result obtained contained degraded membrane material. One of the fouling mechanisms of carbohydrates was adsorption. Carbohydrates were not potential adsorptive foulants to the sameextent as wood extractives because their amount in the fouled membranes was found to be significantly lower than the amount of wood extractives.

Using aster multispectral imagery for mapping woody invasive species in pico da vara natural reserve (Azores Islands, Portugal)

This paper aims to assess the effectiveness of ASTER imagery to support the mapping of Pittosporum undulatum, an invasive woody species, in Pico da Vara Natural Reserve (S. Miguel Island, Archipelago of the Azores, Portugal). This assessment was done by applying K-Nearest Neighbor (KNN), Support Vector Machine (SVM) and Maximum Likelihood (MLC) pixel-based supervised classifications to 4 different geographic and remote sensing datasets constituted by the Visible, Near-Infrared (VNIR) and Short Wave Infrared (SWIR) of the ASTER sensor and by digital cartography associated to orography (altitude and "distance to water streams") of which the spatial distribution of Pittosporum undulatum directly depends. Overall, most performed classifications showed a strong agreement and high accuracy. At targeted species level, the two higher classification accuracies were obtained when applying MLC and KNN to the VNIR bands coupled with auxiliary geographic information use. Results improved significantly by including ecology and occurrence information of species (altitude and distance to water streams) in the classification scheme. These results show that the use of ASTER sensor VNIR spectral bands, when coupled to relevant ancillary GIS data, can constitute an effective and low cost approach for the evaluation and continuous assessment of Pittosporum undulatum woodland propagation and distribution within Protected Areas of the Azores Islands.

DYNAMICS OF LEAF FALL FROM RIPARIAN VEGETATION AND THE ACCUMULATION IN BENTHIC STOCK IN NEOTROPICAL STREAMS1

ABSTRACT Considering the importance of the riparian vegetation leaves as an energetic source to first order streams, the aim of the present study was to evaluate the leaf biomass contribution to the system and its temporal dynamics. With this purpose, monthly samples from July 2008 to June 2009 were collected using four sampling devices installed in three streams, in order to collect the vertical, lateral and terrestrial loads, and the benthic stock. We tested the following hypothesis: (1) leaf biomass input is higher after hydric stress periods; and (2) benthic stock biomass increase with higher loads from vertical and lateral entrances. Leaves represented 71.9% (on average) of all sampled allochthonous matter, with seasonal significant variation along the studied year. Peaks of leaf input were registered in September-October, after an increase in rainfall, and also in January, after a decrease in rainfall. Leaf input was higher in the lateral load.

Warning system based on theoretical-experimental study of dispersion of soluble pollutants in rivers

Information about capacity of transport and dispersion of soluble pollutants in natural streams are important in the management of water resources, especially in planning preventive measures to minimize the problems caused by accidental or intentional waste, in public health and economic activities that depend on the use of water. Considering this importance, this study aimed to develop a warning system for rivers, based on experimental techniques using tracers and analytical equations of one-dimensional transport of soluble pollutants conservative, to subsidizing the decision-making in the management of water resources. The system was development in JAVA programming language and MySQL database can predict the travel time of pollutants clouds from a point of eviction and graphically displays the temporal distribution of concentrations of passage clouds, in a particular location, downstream from the point of its launch.

Käytetyn voiteluöljyn regenerointilaitoksen prosessivesien karakterisointi

Käytetyn voiteluöljyn regeneroinnissa muodostuu prosessivettä useista lähteistä. Tehokas päästöjenhallinta on yksi tärkeimmistä tavoitteista regenerointilaitoksen operoinnissa ja sen takia sitä tulee kehittää jatkuvasti entistä paremmaksi. Tavoitteisiin pääsemiseksi on oleellista tunnistaa vesienkäsittelyprosessin laadullinen massatase ja laadunvaihtelut ajotilanteiden mukaan. Työssä tutkitaan ja analysoidaan veden sisältämiä epäpuhtauksia sekä kirjallisuuslähteiden perusteella, että standardimenetelmillä ja modifioiduilla menetelmillä, joilla on akkreditointi. Analyysituloksista muodostetaan laadullinen massatase, josta nähdään epäpuhtauksien ja niitä kuvaavien parametrien kuormitukset kussakin prosessivesivirrassa. Tulosten perusteella arvioidaan nykyisen vesienkäsittelyn tehokkuutta, sen säätömahdollisuuksia ja kehitystarvetta. Tarkastelun ulkopuolelle kuitenkin jätetään vesienkäsittelystä ulosjohdettavan prosessiveden puhdistuslaitos. Tutkimusten perusteella regenerointilaitoksessa muodostuvien prosessivesien epäpuhtaudet koostuvat öljystä, BTEX-yhdisteistä, fenoliyhdisteistä, liuottimista, polttoaineiden ja voiteluöljyjen lisäaineista, typpi- ja rikkiyhdisteistä, metalliyhdisteistä sekä kiintoaineesta. Öljy jakautuu kevyisiin (C5-C10), keskiraskaisiin (C10-21) ja raskaisiin (C21-40) jakeisiin. Vesienkäsittelyssä suurin osa öljystä ja epäpuhtauksista saadaan erottumaan vedestä, jolloin puhdistuslaitokselle päätyy jäämäpitoisuudet öljyä, haihtuvia yhdisteitä sekä muita epäpuhtauksia. Puhdistuslaitosta kuormittavat eniten liuenneet orgaaniset yhdisteet sekä korkeaa kemiallista hapenkulutusta aiheuttavat epäorgaaniset yhdisteet (suolat), joiden erottamista prosessivesistä on syytä tulevaisuudessa kehittää.

The purpose of consumer co-operation: implications for the management and governance of co-operatives

Extant research on consumer co-operation has acknowledged that the corporate purpose of consumer co-operatives deviates significantly from the purpose of investor-owned firms (IOFs – the dominant form in market economies and in theory development in the field of business economics) and also suggested that the management of consumer co-operatives differs from the management of IOFs. Despite this, there is a scarcity of research focusing on the management of consumer co-operatives in general and the ways this different purpose manifests in their management in particular. In other words, research on consumer cooperatives has only started to discover the importance of identifying the premises of these organizations and generating management and organization theories that take them into account. The overall objective of this study is to map out some of the implications that the purpose of consumer co-operation has for the management and governance of consumer co-operatives. To put it more precisely, by combining interview data gathered from Finnish consumer cooperatives (S Group, OP Bank Group and POP Bank) and extant literature, this study aims to generate or elaborate on definitions and outlines of the features that co-operative purpose poses for the strategic management, governance and managerial competence needed for consumer co-operatives. The study consists of two parts. The first part introduces the research topic, methods and publications, as well as discusses the overall outcomes. The second part consists of four publications that address the research questions from different viewpoints. The analyses of this study indicate that due to the purpose of consumer co-operation, the roles of locality and regionality become emphasized in their management. While locality and regionality are potential sources of competitive advantage for consumer co-operatives, geographic boundness sets significant boundary conditions for the strategic management of these organizations. Further, the purpose of consumer co-operation may pose several challenges to governance and set specific competence demands for the managers of these organizations. Associating the observations from various streams of research on management and governance with the purpose of consumer co-operation and examining these issues further, the thesis contributes to elaboration of theory in the field. While the thesis is by no means comprehensive (but instead reflects a co-operative research project in its early stages), it does shed light on some key ideas of management and governance and offers leads to theory and, thereby, will prove useful to elaborators, disseminators and appliers of knowledge on co-operation.

Sellutehtaan vedenkäytön vähentäminen

Työn tarkoituksena oli etsiä mahdollisia kohteita sellutehtaan veden käytön vähen-tämiseksi. Analyysien avulla selvitettiin voidaanko havaittujen kohteiden tällä hetkellä menetettyjä vesivirtoja käyttää uudelleen. Lopuksi arvioitiin miten kierrä-tettävät vedet vaikuttaisivat raakaveden laatuun, mikäli ne yhdistettäisiin tämän joukkoon. Veden käytön vähentämiskohteita etsittiin tutkimalla tehtaan prosessi-kaavioita osastokohtaisesti sekä selvittämällä näin havaittuja kohteita osastoilla. Työn kokeellinen osa koostui vesianalyyseistä. Vesianalyyseissä määritettiin seu-raavat arvot sellutehtaalle tulevasta vedestä: sameus (FTU), kiintoaine, sähkönjoh-tavuus, pH, CODCr, BOD7ATU, kokonaisfosfori P, Mn, Cl, K, Ca, Mg ja AOX. Nämä tehtiin valituista kohteista havaituista tällä hetkellä tehtaalta pois johdetuista mutta mahdollisesti kierrätettävistä vesistä. Työn tuloksien perusteella havaittiin, että seuraavissa tarkasteluun valituissa koh-teissa vedet olivat hyvin puhtaita ja talteen otettavia kierrätykseen. Näitä olivat savukaasupesurin vedet, sekundäärilauhdesäiliön vedet sekä tiivistevedet. Haih-duttamon lämminvesisäiliön sekä kuivauskone 4 kiertovesitornin vedet olivat hieman likaantuneet mutta hyvin kierrätettävissä. Koivulinjan D0-vaiheen, havu-linjan D1-vaiheen sekä kuivauskone 4 lajittamon vesivirtoja ei likaantumisen vuoksi kannattanut kerätä hyötykäyttöön.

Pasvik Water Quality Report Environmental Monitoring Programme in the Norwegian, Finnish and Russian Border Area

The Pasvik monitoring programme was created in 2006 as a result of the trilateral cooperation, and with the intention of following changes in the environment under variable pollution levels. Water quality is one of the basic elements of the Programme when assessing the effects of the emissions from the Pechenganikel mining and metallurgical industry (Kola GMK). The Metallurgic Production Renovation Programme was implemented by OJSC Kola GMK to reduce emissions of sulphur and heavy metal concentrated dust. However, the expectations for the reduction in emissions from the smelter in the settlement Nikel were not realized. Nevertheless, Kola GMK has found that the modernization programme’s measures do not provide the planned reductions of sulfur dioxide emissions. In this report, temporal trends in water chemistry during 2000–2009 are examined on the basis of the data gathered from Lake Inari, River Pasvik and directly connected lakes, as well as from 26 small lakes in three areas: Pechenganikel (Russia), Jarfjord (Norway) and Vätsäri (Finland). The lower parts of the Pasvik watercourse are impacted by both atmospheric pollution and direct wastewater discharge from the Pechenganikel smelter and the settlement of Nikel. The upper section of the watercourse, and the small lakes and streams which are not directly linked to the Pasvik watercourse, only receive atmospheric pollution. The data obtained confirms the ongoing pollution of the river and water system. Copper (Cu), nickel (Ni) and sulphates are the main pollution components. The highest levels were observed close to the smelters. The most polluted water source of the basin is the River Kolosjoki, as it directly receives the sewage discharge from the smelters and the stream connecting the Lakes Salmijarvi and Kuetsjarvi. The concentrations of metals and sulphates in the River Pasvik are higher downstream from the Kuetsjarvi Lake. There has been no fall in the concentrations of pollutants in Pasvik watercourse over the last 10 years. Ongoing recovery from acidification has been evident in the small lakes of the Jarfjord and Vätsäri areas during the 2000s. The buffering capacity of these lakes has improved and the pH has increased. The reason for this recovery is that sulphate deposition has decreased, which is also evident in the water quality. However, concentrations of some metals, especially Ni and Cu, have risen during the 2000s. Ni concentrations have increased in all three areas, and Cu concentrations in the Pechenganickel and Jarfjord areas, which are located closer to the smelters. Emission levels of Ni and Cu did not fall during 2000s. In fact, the emission levels of Ni compounds even increased compared to the 1990s.