Preparation of Polymer Nanoparticles by Ring Opening Metathesis Polymerization in Aqueous Dispersed Systems with Water-Soluble Ruthenium-based Catalyst

Ring opening metathesis polymerization (ROMP) is a variant of olefin metathesis used to polymerize strained cyclic olefins. Ruthenium-based Grubbs’ catalysts are widely used in ROMP to produce industrially important products. While highly efficient in organic solvents such as dichloromethane and toluene, these hydrophobic catalysts are not typically applied in aqueous systems. With the advancements in emulsion and miniemulsion polymerization, it is promising to conduct ROMP in an aqueous dispersed phase to generate well-defined latex nanoparticles while improving heat transfer and reducing the use of volatile organic solvents (VOCs). Herein I report the efforts made using a PEGylated ruthenium alkylidene as the catalyst to initiate ROMP in an oil-in-water miniemulsion. 1H NMR revealed that the synthesized PEGylated catalyst was stable and reactive in water. Using 1,5-cyclooctadiene (COD) as monomer, we showed the highly efficient catalyst yielded colloidally stable polymer latexes with ~ 100% conversion at room temperature. Kinetic studies demonstrated first-order kinetics with good livingness as confirmed by the shift of gel permeation chromatography (GPC) traces. Depending on the surfactants used, the particle sizes ranged from 100 to 300 nm with monomodal distributions. The more strained cyclic olefin norbornene (NB) could also be efficiently polymerized with a PEGylated ruthenium alkylidene in miniemulsion to full conversion and with minimal coagulum formation.

Co-production of bio-oil and propylene through the hydrothermal liquefaction of polyhydroxybutyrate producing cyanobacteria

A polyhydroxybutyrate (PHB) producing cyanobacteria was converted through hydrothermal liquefaction (HTL) into propylene and a bio-oil suitable for advanced biofuel production. HTL of model compounds demonstrated that in contrast to proteins and carbohydrates, no synergistic effects were detected when converting PHB in the presence of algae. Subsequently, Synechocystis cf. salina, which had accumulated 7.5wt% PHB was converted via HTL (15% dry weight loading, 340°C). The reaction gave an overall propylene yield of 2.6%, higher than that obtained from the model compounds, in addition to a bio-oil with a low nitrogen content of 4.6%. No propylene was recovered from the alternative non-PHB producing cyanobacterial strains screened, suggesting that PHB is the source of propylene. PHB producing microorganisms could therefore be used as a feedstock for a biorefinery to produce polypropylene and advanced biofuels, with the level of propylene being proportional to the accumulated amount of PHB.

Co-production of bio-oil and propylene through the hydrothermal liquefaction of polyhydroxybutyrate producing cyanobacteria

A polyhydroxybutyrate (PHB) producing cyanobacteria was converted through hydrothermal liquefaction (HTL) into propylene and a bio-oil suitable for advanced biofuel production. HTL of model compounds demonstrated that in contrast to proteins and carbohydrates, no synergistic effects were detected when converting PHB in the presence of algae. Subsequently, Synechocystis cf. salina, which had accumulated 7.5wt% PHB was converted via HTL (15% dry weight loading, 340°C). The reaction gave an overall propylene yield of 2.6%, higher than that obtained from the model compounds, in addition to a bio-oil with a low nitrogen content of 4.6%. No propylene was recovered from the alternative non-PHB producing cyanobacterial strains screened, suggesting that PHB is the source of propylene. PHB producing microorganisms could therefore be used as a feedstock for a biorefinery to produce polypropylene and advanced biofuels, with the level of propylene being proportional to the accumulated amount of PHB.

Assessing hydrothermal liquefaction for the production of bio-oil and enhanced metal recovery from microalgae cultivated on acid mine drainage

The hydrothermal liquefaction(HTL) of algal biomass is a promising route to viable second generation biofuels. In this investigation HTL was assessed for the valorisation of algae used in the remediation of acid mine drainage (AMD). Initially the HTL process was evaluated using Arthrospira platensis (Spirulina) with additional metal sulphates to simulate metal remediation. Optimised conditions were then used to process a natural algal community (predominantly Chlamydomonas sp.) cultivated under two scenarios: high uptake and low uptake of metals from AMD. High metal concentrations appear to catalyse the conversion to bio-oil, and do not significantly affect the heteroatom content or higher heating value of the bio-oil produced. The associated metals were found to partition almost exclusively into the solid residue, favourable for potential metal recovery. High metal loadings also caused partitioning of phosphates from the aqueous phase to the solid phase, potentially compromising attempts to recycle process water as a growth supplement. HTL was therefore found to be a suitable method of processing algae used in AMD remediation, producing a crude oil suitable for upgrading into hydrocarbon fuels, an aqueous and gas stream suitable for supplementing the algal growth and the partitioning of most contaminant metals to the solid residue where they would be readily amenable for recovery and/or disposal.

Assessing hydrothermal liquefaction for the production of bio-oil and enhanced metal recovery from microalgae cultivated on acid mine drainage

The hydrothermal liquefaction(HTL) of algal biomass is a promising route to viable second generation biofuels. In this investigation HTL was assessed for the valorisation of algae used in the remediation of acid mine drainage (AMD). Initially the HTL process was evaluated using Arthrospira platensis (Spirulina) with additional metal sulphates to simulate metal remediation. Optimised conditions were then used to process a natural algal community (predominantly Chlamydomonas sp.) cultivated under two scenarios: high uptake and low uptake of metals from AMD. High metal concentrations appear to catalyse the conversion to bio-oil, and do not significantly affect the heteroatom content or higher heating value of the bio-oil produced. The associated metals were found to partition almost exclusively into the solid residue, favourable for potential metal recovery. High metal loadings also caused partitioning of phosphates from the aqueous phase to the solid phase, potentially compromising attempts to recycle process water as a growth supplement. HTL was therefore found to be a suitable method of processing algae used in AMD remediation, producing a crude oil suitable for upgrading into hydrocarbon fuels, an aqueous and gas stream suitable for supplementing the algal growth and the partitioning of most contaminant metals to the solid residue where they would be readily amenable for recovery and/or disposal.

Simulation of Oil Shale Semi-Coke Particle Cold Transportation in a Spouted Bed Using CPFD Method

The spouted bed was widely used due to its good mixing of particles and effective phase transferability between the gas and solid phase. In this paper, the transportation process of particles in a 3D spouted bed was studied using the Computational Particle Fluid Dynamics (CPFD) numerical method. Experiments were conducted to verify the validity of the simulation results. Distributions of the pressure, velocities and particle concentration of transportation devices were investigated. The motion state and characteristics of multiphase flows in the transportation device were demonstrated under various operating conditions. The results showed that a good consistency was obtained between the simulated results and the experimental results. The motion characteristics of the gas-solid two-phase flow in the device was effectively predicted, which could assist the optimal operating condition estimation for the spouted transportation process.

Simulations in 3D research : Can Unity3D be used to simulate a 3D display system?

Mid Sweden University is currently researching how to capture more of a scene with a camera and how to create 3D images that does not require extra equipment for the viewer. In the process of this research they have started looking into simulating some of the tests that they wish to conduct. The goal of this project is to research whether the 3D graphics engine Unity3D could be used to simulate these tests, and to what degree. To test this a simulation was designed and implemented. The simulation used a split display system where each camera is directly connected to a part of the screen and using the position of the viewer the correct part of the camera feed is shown. Some literary studies were also done into how current 3D technology works. The simulation was successfully implemented and shows that simple simulation can be done in Unity3D, however, some problems were encountered in the process. The conclusion of the project show that there is much work left before simulation is viable but that there is potential in the technology and that the research team should continue to investigate it.

Oil Flow Rate Measurements Using 198au And Total Count Technique

In industrial plants, oil and oil compounds are usually transported by closed pipelines with circular cross-section. The use of radiotracers in oil transport and processing industrial facilities allows calibrating flowmeters, measuring mean residence time in cracking columns, locate points of obstruction or leak in underground ducts, as well as investigating flow behavior or industrial processes such as in distillation towers. Inspection techniques using radiotracers are non-destructive, simple, economic and highly accurate. Among them, Total Count, which uses a small amount of radiotracer with known activity, is acknowledged as an absolute technique for flow rate measurement. A viscous fluid transport system, composed by four PVC pipelines with 13m length (12m horizontal and 1m vertical) and ½, ¾, 1 and 2-inch gauges, respectively, interconnected by maneuvering valves was designed and assembled in order to conduct the research. This system was used to simulate different flow conditions of petroleum compounds and for experimental studies of flow profile in the horizontal and upward directions. As 198Au presents a single photopeak (411,8 keV), it was the radioisotope chosen for oil labeling, in small amounts (6 ml) or around 200 kBq activity, and it was injected in the oil transport lines. A NaI scintillation detector 2”x 2”, with well-defined geometry, was used to measure total activity, determine the calibration factor F and, positioned after a homogenization distance and interconnected to a standardized electronic set of nuclear instrumentation modules (NIM), to detect the radioactive cloud.

Evaluation of Cross Correlation Technique to Measure Flow in Pipes of the Oil Industry

The present work is concerned with the use of the cross correlation technique to measure delay time between two simulated signals displaced with respect to time, in order to develop a cross correlator system that will be used to measure the water and oil pipes flowrate in which the detection system is composed by two external low intensity radiation sources located along the tube and two NaI(Tl) gamma-ray detectors. The final purpose of the correlator system is to use the natural disturbances, as the turbulence in the own flow rather than to inject radioactive tracers to the fluid flow as usually is carried out. In the design of this correlator is evaluated the point-by-point calculation method for the cross correlation function in order to produce a system accurate and fast. This method is divided at the same time in three modes of operation: direct, relay and polarity.

Optimization of wastepaper sludge ash (WSA) in robust cementitious systems

Abstract : Wastepaper sludge ash (WSA) is generated by a cogeneration station by burning wastepaper sludge. It mainly consists of amorphous aluminosilicate phase, anhydrite, gehlenite, calcite, lime, C2S, C3A, quartz, anorthite, traces of mayenite. Because of its free lime content (~10%), WSA suspension has a high pH (13). Previous researchers have found that the WSA composition has poor robustness and the variations lead to some unsoundness for Portland cement (PC) blended WSA concrete. This thesis focused on the use of WSA in different types of concrete mixes to avoid the deleterious effect of the expansion due to the WSA hydration. As a result, WSA were used in making alkali-activated materials (AAMs) as a precursor source and as a potential activator in consideration of its amorphous content and the high alkaline nature. Moreover, the autogenous shrinkage behavior of PC concrete at low w/b ratio was used in order to compensate the expansion effect due to WSA. The concrete properties as well as the volume change were investigated for the modified WSA blended concrete. The reaction mechanism and microstructure of newly formed binder were evaluated by X-ray diffraction (XRD), calorimetry, thermogravimetric analysis (TGA), scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX). When WSA was used as precursor, the results showed incompatible reaction between WSA and alkaline solution. The mixtures were not workable and provided very low compressive strength no matter what kinds of chemical activators were used. This was due to the metallic aluminum in WSA, which releases abundant hydrogen gas when WSA reacts with strong alkaline solution. Besides, the results of this thesis showed that WSA can activate the glassy phase contained in slag, glass powder (GP) and class F fly ash (FFA) with an optimum blended ratio of 50:50. The WSA/slag (mass ratio of 50:50) mortar (w/b of 0.47) attained 46 MPa at 28 days without heat curing assistance. A significant fast setting was noticed for the WSA-activated binder due to the C3A phase, free lime and metallic aluminum contained in the WSA. Adding 5% of gypsum can delay the fast setting, but this greatly increased the potential risk of intern sulfate attack. The XRD, TGA and calorimetry analyses demonstrated the formation of ettringite, C-S-H, portlandite, hydrogarnet and calcium carboaluminate in the hydrated binder. The mechanical performance of different binder was closely related to the microstructure of corresponding binder which was proved by the SEM observation. The hydrated WSA/slag and WSA/FFA binder formed a C-A-S-H type of gel with lower Ca/Si ratio (0.47~1.6). A hybrid gel (i.e. C-N-A-S-H) was observed for the WSA/GP binder with a very low Ca/Si ratio (0.26) and Na/Si ratio (0.03). The SEM/EDX analyses displayed the formation of expansive gel (ettringite and thaumasite) in the gypsum added WSA/slag concrete. The gradual emission of hydrogen gas due to the reaction of WSA with alkaline environment significantly increased the porosity and degraded the microstructure of hydrated matrix after the setting. In the last phase of this research WSA-PC blended binder was tailored to form a high autogenous shrinkage concrete in order to compensate the initial expansion. Different binders were proportioned with PC, WSA, silica fume or slag. The microstructure and mechanical properties of concrete can be improved by decreasing w/b ratios and by incorporating silica fume or slag. The 28-day compressive strength of WSA-blended concrete was above 22 MPa and reached 45 MPa when silica fume was added. The PC concrete incorporating silica fume or slag tended to develop higher autogenous shrinkage at low w/b ratios, and thus the ternary binder with the addition of WSA inhibited the long term shrinkage due to the initial expansion property to WSA. In the restrained shrinkage test, the concrete ring incorporating the ternary binder (PC/WSA/slag) revealed negligible potential to cracking up to 96 days as a result of the offset effect by WSA expansion. The WSA blended regular concrete could be produced for potential applications with reduced expansion, good mechanical property and lower permeability.

The Usability of a Commercial Game Physics Engine to Develop Physics Educational Materials: an Investigation

Commercial computer games contain “physics engine” components, responsible for providing realistic interactions among game objects. The question naturally arises of whether these engines can be used to develop educational materials for high school and university physics education. To answer this question, the author's group recently conducted a detailed scientific investigation of the physics engine of Unreal Tournament 2004 (UT2004). This article presents their motivation, methodology, and results. The author presents the findings of experiments that probed the accessibility and fidelity of UT2004's physics engine, examples of educational materials developed, and an evaluation of their use in high school classes. The associated pedagogical implications of this approach are discussed, and the author suggests guidelines for educators on how to deploy the approach. Key resources are presented on an associated Web site.

Learning Physics with the Unreal Tournament Engine

Computer games such as Unreal Tournament (UT2004 and UT3) contain a 'physics engine' responsible for producing believable dynamic interactions between players and objects in the three-dimensional (3D) virtual world of a game. Through a series of probing experiments we have evaluated the fidelity and internal consistency of the UT2004 physics engine. These experiments have then led to the production of resources which may be used by learners and teachers of secondary-school physics. We also suggest an approach to learning, where both teachers and pupils may produce learning materials using the Unreal Tournament editor 'UnrealEd'.

A Study of Environmental Disclosures in the European Oil and Gas Industry : With Reference to the Global Reporting Initiative

Background and Problem: Sustainability reporting is a growing trend in the society. One of the most exposed industries to environmental matters is the oil and gas industry, which commit to sustainability reporting in order to deal with the industry’s destructive operations. The Global Reporting Initiative (GRI) provides voluntary guidelines in sustainability reporting, which increase transparency for the company’s stakeholders. However, it is controversial that the oil and gas industry put a great effort into sustainability reporting even though the industry is environmentally destructive. This gap is interesting to investigate and will contribute to the academic discussion. Therefore, this thesis will focus on the sustainability reporting in the oil and gas industry and to what extent the industry actually discloses material environmental information about their operations. Purpose: The purpose of this thesis is to examine how the sustainability reporting has changed in the oil and gas industry in Europe. This is performed from a stakeholder perspective. Further, it aims to investigate how oil and gas companies have followed the GRI guidelines and how the reporting has changed over time. Method: A quantitative method is used in order to answer the research questions. The data sample is based on oil and gas companies reporting according to the GRI framework during year 2012 to year 2014. The empirical data is gathered from the studied companies’ environmental category in their sustainability reports. Further, a content analysis technique, with a coding scheme, was set up to interpret and analyse the information. To enable an easy overview of the findings, the relevant data is presented in tables and diagrams. Empirical Findings and Conclusion: The majority of the studied companies have increased their level of compliance in the environmental category. Although, the majority of the companies have increased their reporting, the compliance level differs between the companies. The most reported sectors are the; “Water”, “Biodiversity”, “Emissions”, “Effluents and Waste”, “Compliance”, and “Overall”. Further, the empirical findings show that there is an overall increase in the amount of disclosed information per indicator. The conclusion of this thesis is that the environmental disclosures have increased in the oil and gas industry from year 2012 to 2014.

Anise Myrtle (Syzygium anisatum) Oils

Syzygium anisatum (formerly Backhousia anisata and Anetholea anisata) is an Australian rainforest tree with leaves that produce an essential oil (EO) that has the characteristic aroma of aniseed. It is referred to as aniseed myrtle or anise myrtle in the trade and the fresh and dried leaves of this plant are used as a herb in culinary applications. The EO is extracted by steam distillation of the leaves and the major aromatic volatile compound is anethole. The EO has broad spectrum antimicrobial activity but is more effective against bacteria than fungi. Indigenous Australians have used anise myrtle for its medicinal values and in recent times it has been used as a flavoring agent by the food and beverage industry. This chapter covers the use of anise myrtle EO in food and agricultural applications, botanical aspects, and chemical composition.

A numerical model for prediction of oil, trajectory due to extraction activity in the north coasts of the Persian Gulf

This thesis considers a three- dimensional numerical model based on 3-D Navier— Stokes and continuity equations involving various wind speeds (North west), water surface levels, horizontal shier stresses, eddy viscosity, densities of oil and gas condensate- water mixture flows. The model is used to simulate the prediction of the surface movement of oil and gas condensate slicks from spill accident in the north coasts of Persian Gulf.