Self-standing curved crystals for X and Gamma rays focusing

The efficiency of a Laue lens for X and Gamma ray focusing in the energy range 60 ÷ 600 keV is closely linked to the diffraction efficiency of the single crystals composing the lens. A powerful focusing system is crucial for applications like medical imaging and X ray astronomy where wide beams must be focused. Mosaic crystals with a high density, such as Cu or Au, and bent crystals with curved diffracting planes (CDP) are considered for the realization of a focusing system for X rays, owing to their high diffraction efficiency. In this work, a comparison of the efficiency of CDP crystals and mosaic crystals was performed on the basis of the theory of X-ray diffraction. Si, GaAs and Ge CDP crystals with optimized thicknesses and moderate radii of curvature of several tens of metres demonstrate comparable or superior performance with respect to the higher atomic number mosaic crystals generally used. A simplified approach for calculating the integrated reflectivity of the crystals is applied. A bending technique used during this work to realize CDP crystals consists in a controlled surface damaging induced by a mechanical lapping process. A compressive strained layer of few micrometres in thickness is generated and causes the convex curvature of the damaged side of the crystal. Another new bending technique is developed and the main results are shown. The process consists on a film deposition of a selected bi-component epoxy resin on one side of crystal, made uniform in thickness by mean of a spin-coater. Choosing the speed of spin-coating, so changing the thickness of the film, a control of radius of curvature can be obtained. Moreover the possibility to combine the two bending technique to obtain CDP crystal with a stronger curvature in rather thick crystals was demonstrated. Detailed characterization of Si, and GaAs CDP crystals at low and high x-ray energies are performed on flat and bent crystals obtained with the damaging and the resin deposition technique. As expected an increase of diffraction efficiency in asymmetrical diffraction geometry in CDP crystals with respect to the flat ones is observed. On the other hand an unexpected increase of the integrated intensity in symmetrical geometry, not predicted by the theory, is observed in all the measurements performed with different set up. The experimental trend of the integrated reflectivity as a function of the radius of curvature is in a good agreement with that predicted by the theory of bent perfect crystals, so it is possible to conclude that the surface damage has a limited effect on the crystal reflectivity. A study of the integrated reflectivity in the energy range of interest (100÷350 keV) in CDP crystals realized with damaging and resin deposition technique at symmetrical and asymmetrical geometries was performed at ILL Institute. Also at these energies the diffraction efficiency of bent crystals was much larger (a 12 time increase is observed for bent crystals in asymmetrical 111 geometry) than that measured in flat crystals. The diffraction efficiency of CDP crystals realized with both techniques tends to coincide with that of flat crystals at very high energies (> 200 keV). This suggesting that also real flat perfect crystals can be considered as strongly bent or mosaic crystals at very high X ray energies.

Phosphonate and quinoxaline cavitands for molecular recognition and sensing

In the last decade, phosphonate and quinoxaline cavitand have been extensively studied, highlighting their outstanding recognition properties. Their successful applications in material science and sensing open the way to new potential applications, such as border security, environmental monitoring and chiral recognition. The present thesis explores the recognition properties of phosphonate and quinoxaline cavitands towards new targets, for molecular recognition and sensing applications. Chapter 2 highlights the enantioselective behavior of phosphonate cavitands towards chiral guests in the solid state and in solution. Phosphonate cavitands were exploited for the molecular recognition of L-lactic acid (chapter 3), a widespread natural molecule which offer multiple potential applications, and a human sweat marker used for the detection of human presence (chapter 4). The second part is devoted to sensing applications of quinoxaline cavitands. Chapter 5 describes the use of QxCav for the preconcentration of drugs precursors, while chapter 6 reports the design, synthesis and grafting of a rigidified EtQxBox on a silicon wafer.

Interazione di nanoparticelle metalliche con menbrane biologiche: risultati di studi in vitro su cute, mucosa del cavo orale e meningi ed implicazioni per la salute

L’utilizzo di nanomateriali, ovvero una nuova classe di sostanze composte da particelle ultrafini con dimensioni comprese fra 1 e 100 nm (American Society for Testing Materials - ASTM), è in costante aumento a livello globale. La particolarità di tali sostanze è rappresentata da un alto rapporto tra la superficie e il volume delle particelle, che determina caratteristiche chimico-fisiche completamente differenti rispetto alle omologhe macrosostanze di riferimento. Tali caratteristiche sono tali da imporre una loro classificazione come nuovi agenti chimici (Royal Society & Royal Academy of Engineering report 2004). Gli impieghi attuali dei nanomateriali risultano in continua evoluzione, spaziando in diversi ambiti, dall’industria farmaceutica e cosmetica, all’industria tessile, elettronica, aerospaziale ed informatica. Diversi sono anche gli impieghi in campo biomedico; tra questi la diagnostica e la farmacoterapia. È quindi prevedibile che in futuro una quota sempre maggiore di lavoratori e consumatori risulteranno esposti a tali sostanze. Allo stato attuale non vi è una completa conoscenza degli effetti tossicologici ed ambientali di queste sostanze, pertanto, al fine di un loro utilizzo in totale sicurezza, risulta necessario capirne meglio l’impatto sulla salute, le vie di penetrazione nel corpo umano e il rischio per i lavoratori conseguente al loro utilizzo o lavorazione. La cute rappresenta la prima barriera nei confronti delle sostanze tossiche che possono entrare in contatto con l’organismo umano. Successivamente agli anni ‘60, quando si riteneva che la cute rappresentasse una barriera totalmente impermeabile, è stato dimostrato come essa presenti differenti gradi di permeabilità nei confronti di alcuni xenobiotici, dipendente dalle caratteristiche delle sostanze in esame, dal sito anatomico di penetrazione, dal grado di integrità della barriera stessa e dall’eventuale presenza di patologie della cute. La mucosa del cavo orale funge da primo filtro nei confronti delle sostanze che entrano in contatto con il tratto digestivo e può venir coinvolta in contaminazioni di superficie determinate da esposizioni occupazionali e/o ambientali. È noto che, rispetto alla cute, presenti una permeabilità all’acqua quattro volte maggiore, e, per tale motivo, è stata studiata come via di somministrazione di farmaci, ma, ad oggi, pochi sono gli studi che ne hanno valutato le caratteristiche di permeazione nei confronti delle nanoparticelle (NPs). Una terza importante barriera biologica è quella che ricopre il sistema nervoso centrale, essa è rappresentata da tre foglietti di tessuto connettivo, che assieme costituiscono le meningi. Questi tre foglietti rivestono completamente l’encefalo permettendone un isolamento, tradizionalmente ritenuto completo, nei confronti degli xenobiotici. L’unica via di assorbimento diretto, in questo contesto, è rappresentata dalla via intranasale. Essa permette un passaggio diretto di sostanze dall’epitelio olfattivo all’encefalo, eludendo la selettiva barriera emato-encefalica. Negli ultimi anni la letteratura scientifica si è arricchita di studi che hanno indagato le caratteristiche di assorbimento di farmaci attraverso questa via, ma pochissimi sono gli studi che hanno indagato la possibile penetrazione di nanoparticelle attraverso questa via, e nessuno, in particolar modo, ha indagato le caratteristiche di permeazione delle meningi. L’attività di ricerca svolta nell’ambito del presente dottorato ha avuto per finalità l’indagine delle caratteristiche di permeabilità e di assorbimento della cute, della mucosa del cavo orale e delle meningi nei confronti di alcune nanoparticelle, scelte fra quelle più rappresentative in relazione alla diffusione d’utilizzo a livello globale. I risultati degli esperimenti condotti hanno dimostrato, in vitro, che l’esposizione cutanea a Pt, Rh, Co3O4 e Ni NPs determinano permeazione in tracce dei medesimi metalli attraverso la cute, mentre per le TiO2 NPs tale permeazione non è stata dimostrata. È stato riscontrato, inoltre, che la mucosa del cavo orale e le meningi sono permeabili nei confronti dell’Ag in forma nanoparticellare.

Study of interaction between Si(O,C) nanowires and the biological system

Nanomedicine is a new branch of medicine, based on the potentiality and intrinsic properties of nanomaterials. Indeed, the nanomaterials ( i.e. the materials with nano and under micron size) can be suitable to different applications in biomedicine. The nanostructures can be used by taking advantage of their properties (for example superparamagnetic nanoparticles) or functionalized to deliver the drug in a specific target, thanks the ability to cross biological barriers. The size and the shape of 1D-nanostructures (nanotubes and nanowires) have an important role on the cell fate: their morphology plays a key role on the interaction between nanostructure and the biological system. For this reason the 1D nanostructure are interesting for their ability to mime the biological system. An implantable material or device must therefore integrate with the surrounding extracellular matrix (ECM), a complex network of proteins with structural and signaling properties. Innovative techniques allow the generation of complex surface patterns that can resemble the structure of the ECM, such as 1D nanostructures. NWs based on cubic silicon carbide (3C-SiC), either bare (3C-SiC NWs) or surrounded by an amorphous shell (3C-SiC/SiO2 core/shell NWs), and silicon oxycarbide nanowires (SiOxCy NWs) can meet the chemical, mechanical and electrical requirements for tissue engineering and have a strong potential to pave the way for the development of a novel generation of implantable nano-devices. Silicon oxycarbide shows promising physical and chemical properties as elastic modulus, bending strength and hardness, chemical durability superior to conventional silicate glasses in aggressive environments and high temperature stability up to 1300 °C. Moreover, it can easily be engineered through functionalization and decoration with macro-molecules and nanoparticles. Silicon carbide has been extensively studied for applications in harsh conditions, as chemical environment, high electric field and high and low temperature, owing to its high hardness, high thermal conductivity, chemical inertness and high electron mobility. Also, its cubic polytype (3C) is highly biocompatible and hemocompatible, and some prototypes of biomedical applications and biomedical devices have been already realized starting from 3C-SiC thin films. Cubic SiC-based NWs can be used as a biomimetic biomaterial, providing a robust and novel biocompatible biological interface . We cultured in vitro A549 human lung adenocarcinoma epithelial cells and L929 murine fibroblast cells over core/shell SiC/SiO2, SiOxCy and bare 3C-SiC nanowire platforms, and analysed the cytotoxicity, by indirect and direct contact tests, the cell adhesion, and the cell proliferation. These studies showed that all the nanowires are biocompatible according to ISO 10993 standards. We evaluated the blood compatibility through the interaction of the nanowires with platelet rich plasma. The adhesion and activation of platelets on the nanowire bundles, assessed via SEM imaging and soluble P-selectin quantification, indicated that a higher platelet activation is induced by the core/shell structures compared to the bare ones. Further, platelet activation is higher with 3C-SiC/SiO2 NWs and SiOxCyNWs, which therefore appear suitable in view of possible tissue regeneration. On the contrary, bare 3C-SiC NWs show a lower platelet activation and are therefore promising in view of implantable bioelectronics devices, as cardiovascular implantable devices. The NWs properties are suitable to allow the design of a novel subretinal Micro Device (MD). This devices is based on Si NWs and PEDOT:PSS, though the well know principle of the hybrid ordered bulk heterojunction (OBHJ). The aim is to develop a device based on a well-established photovoltaic technology and to adapt this know-how to the prosthetic field. The hybrid OBHJ allows to form a radial p–n junction on a nanowire/organic structure. In addition, the nanowires increase the light absorption by means of light scattering effects: a nanowires based p-n junction increases the light absorption up to the 80%, as previously demonstrated, overcoming the Shockley-Queisser limit of 30 % of a bulk p-n junction. Another interesting employment of these NWs is to design of a SiC based epicardial-interacting patch based on teflon that include SiC nanowires. . Such contact patch can bridge the electric conduction across the cardiac infarct as nanowires can ‘sense’ the direction of the wavefront propagation on the survival cardiac tissue and transmit it to the downstream surivived regions without discontinuity. The SiC NWs are tested in terms of toxicology, biocompatibility and conductance among cardiomyocytes and myofibroblasts.

Electrical investigation of p-type 4H-SiC heavily doped by ion implantation

In the last decades, an increasing interest in the research field of wide bandgap semiconductors was observed, mostly due to the progressive approaching of silicon-based devices to their theoretical limits. 4H-SiC is an example among these, and is a mature compound for applications. The main advantages offered 4H-SiC in comparison with silicon are an higher breakdown field, an higher thermal conductivity, a higher operating temperature, very high hardness and melting point, biocompatibility, but also low switching losses in high frequencies applications and lower on-resistances in unipolar devices. Then, 4H-SiC power devices offer great performance improvement; moreover, they can work in hostile environments where silicon power devices cannot function. Ion implantation technology is a key process in the fabrication of almost all kinds of SiC devices, owing to the advantage of a spatially selective doping. This work is dedicated to the electrical investigation of several differently-processed 4H-SiC ion- implanted samples, mainly through Hall effect and space charge spectroscopy experiments. It was also developed the automatic control (Labview) of several experiments. In the work, the effectiveness of high temperature post-implant thermal treatments (up to 2000°C) were studied and compared considering: (i) different methods, (ii) different temperatures and (iii) different duration of the annealing process. Preliminary p + /n and Schottky junctions were also investigated as simple test devices. 1) Heavy doping by ion implantation of single off-axis 4H-SiC layers The electrical investigation is one of the most important characterization of ion-implanted samples, which must be submitted to mandatory post-implant thermal treatment in order to both (i) recover the lattice after ion bombardment, and (ii) address the implanted impurities into lattice sites so that they can effectively act as dopants. Electrical investigation can give fundamental information on the efficiency of the electrical impurity activation. To understand the results of the research it should be noted that: (a) To realize good ohmic contacts it is necessary to obtain spatially defined highly doped regions, which must have conductivity as low as possible. (b) It has been shown that the electrical activation efficiency and the electrical conductivity increase with the annealing temperature increasing. (c) To maximize the layer conductivity, temperatures around 1700°C are generally used and implantation density high till to 10 21 cm -3 . In this work, an original approach, different from (c), is explored by the using very high annealing temperature, around 2000°C, on samples of Al + -implant concentration of the order of 10 20 cm -3 . Several Al + -implanted 4H-SiC samples, resulting of p-type conductivity, were investigated, with a nominal density varying in the range of about 1-5∙10 20 cm -3 and subjected to two different high temperature thermal treatments. One annealing method uses a radiofrequency heated furnace till to 1950°C (Conventional Annealing, CA), the other exploits a microwave field, providing a fast heating rate up to 2000°C (Micro-Wave Annealing, MWA). In this contest, mainly ion implanted p-type samples were investigated, both off-axis and on-axis <0001> semi-insulating 4H-SiC. Concerning p-type off-axis samples, a high electrical activation of implanted Al (50-70%) and a compensation ratio below 10% were estimated. In the work, the main sample processing parameters have been varied, as the implant temperature, CA annealing duration, and heating/cooling rates, and the best values assessed. MWA method leads to higher hole density and lower mobility than CA in equivalent ion implanted layers, resulting in lower resistivity, probably related to the 50°C higher annealing temperature. An optimal duration of the CA treatment was estimated in about 12-13 minutes. A RT resistivity on the lowest reported in literature for this kind of samples, has been obtained. 2) Low resistivity data: variable range hopping Notwithstanding the heavy p-type doping levels, the carrier density remained less than the critical one required for a semiconductor to metal transition. However, the high carrier densities obtained was enough to trigger a low temperature impurity band (IB) conduction. In the heaviest doped samples, such a conduction mechanism persists till to RT, without significantly prejudice the mobility values. This feature can have an interesting technological fall, because it guarantee a nearly temperature- independent carrier density, it being not affected by freeze-out effects. The usual transport mechanism occurring in the IB conduction is the nearest neighbor hopping: such a regime is effectively consistent with the resistivity temperature behavior of the lowest doped samples. In the heavier doped samples, however, a trend of the resistivity data compatible with a variable range hopping (VRH) conduction has been pointed out, here highlighted for the first time in p-type 4H-SiC. Even more: in the heaviest doped samples, and in particular, in those annealed by MWA, the temperature dependence of the resistivity data is consistent with a reduced dimensionality (2D) of the VRH conduction. In these samples, TEM investigation pointed out faulted dislocation loops in the basal plane, whose average spacing along the c-axis is comparable with the optimal length of the hops in the VRH transport. This result suggested the assignment of such a peculiar behavior to a kind of spatial confinement into a plane of the carrier hops. 3) Test device the p + -n junction In the last part of the work, the electrical properties of 4H-SiC diodes were also studied. In this case, a heavy Al + ion implantation was realized on n-type epilayers, according to the technological process applied for final devices. Good rectification properties was shown from these preliminary devices in their current-voltage characteristics. Admittance spectroscopy and deep level transient spectroscopy measurements showed the presence of electrically active defects other than the dopants ones, induced in the active region of the diodes by ion implantation. A critical comparison with the literature of these defects was performed. Preliminary to such an investigation, it was assessed the experimental set up for the admittance spectroscopy and current-voltage investigation and the automatic control of these measurements.

Photoconductivity and Electro-Optical Properties of Wide Band Gap Metal Oxides

The PhD activity described in this Thesis was focused on the study of metal-oxide wide-bandgap materials, aiming at fabricating new optoelectronic devices such as solar-blind UV photodetectors, high power electronics, and gas sensors. Photocurrent spectroscopy and DC photocurrent time evolution were used to investigate the performance of prototypes under different atmospheres, temperatures and excitation wavelengths (or dark conditions). Cathodoluminescence, absorption spectroscopy, XRD and SEM were used to assess structural, morphologic, electrical and optical properties of materials. This thesis is divided into two main sections, each describing the work done on a different metal-oxide semiconductor. 1) MOVPE-grown Ga2O3 thin films for UV solar-blind photodetectors and high power devices The semiconducting oxides, among them Ga2O3, have been employed for several decades as transparent conducting oxide (TCO) electrodes for fabrication of solar cells, displays, electronic, and opto-electronic devices. The interest was mainly confined to such applications, as these materials tend to grow intrinsically n-type, and attempts to get an effective p-type doping has consistently failed. The key requirements of TCO electrodes are indeed high electrical conductivity and good transparency, while crystallographic perfection is a minor issue. Furthermore, for a long period no high-quality substrates and epi-layers were available, which in turn impeded the development of a truly full-oxide electronics. Recently, Ga2O3 has attracted renewed interest, as large single crystals and high-quality homo- and hetero-epitaxial layers became available, which paved the way to novel application areas. Our research group spent the last two years in developing a low temperature (500-700°C) MOVPE growth procedure to obtain thin films of Ga2O3 on different substrates (Dept. of Physics and IMEM-CNR at UNIPR). We obtained a significant result growing on oriented sapphire epitaxial films of high crystalline, undoped, pure phase -Ga2O3 (hexagonal). The crystallographic properties of this phase were investigated by XRD, in order to clarify the lattice parameters of the hexagonal cell. First design and development of solar blind UV photodetectors based on -phase was carried out and the optoelectronic performance is evaluated by means of photocurrent spectroscopy. The UV-response is adequately fast and reliable to render this unusual phase a subject of great interest for future applications. The availability of a hexagonal phase of Ga2O3 stable up to 700°C, belonging to the same space group of gallium nitride, with high crystallinity and tunable electrical properties, is intriguing in view of the development of nitride-based devices, by taking advantage of the more favorable symmetry and epitaxial relationships with respect to the monoclinic β-phase. In addition, annealing at temperatures higher than 700°C demonstrate that the hexagonal phase converts totally in the monoclinic one. 2) ZnO nano-tetrapods: charge transport mechanisms and time-response in optoelectronic devices and sensors Size and morphology of ZnO at the nanometer scale play a key role in tailoring its physical and chemical properties. Thanks to the possibility of growing zinc oxide in a variety of different nanostructures, there is a great variety of applications, among which gas sensors, light emitting diodes, transparent conducting oxides, solar cells. Even if the operation of ZnO nanostructure-based devices has been recently demonstrated, the mechanisms of charge transport in these assembly is still under debate. The candidate performed an accurate investigation by photocurrent spectroscopy and DC-photocurrent time evolution of electrical response of both single-tetrapod and tetrapod-assembly devices. During the research done for this thesis, a thermal activation energy enables the performance of samples at high temperatures (above about 300°C). The energy barrier is related to the leg-to-leg interconnection in the assembly of nanotetrapods. Percolation mechanisms are responsible for both the very slow photo-response (minutes to hours or days) and the significant persistent photocurrent. Below the bandgap energy, electronic states were investigated but their contribution to the photocurrent are two-three order of magnitude lower than the band edge. Such devices are suitable for employ in photodetectors as well as in gas sensors, provided that the mechanism by which the photo-current is generated and gas adsorption on the surface modify the conductivity of the material are known.

Design and synthesis of new multitarget inhibitors of dengue virus replication

Attraverso una combinazione di virtual screening/virtual library generation abbiamo identificato una nuova serie di inibitori della replicazione del virus Dengue, attivi sia su un target virale (NS5) sia su uno cellulare (Src chinasi)

Nova técnica de julgamento de casos repetitivos à luz do novo Código de Processo Civil: o incidente de resolução de demandas repetitivas

A presente Tese analisa o incidente de resolução de demandas repetitivas. Trata-se de uma nova técnica de julgamento dos denominados processos de massa, instituída pelo Novo Código de Processo Civil. Inicialmente, procurou-se demonstrar o caminho trilhado pelo legislador brasileiro, por meio de sucessivas reformas ao Código de Processo Civil, no sentido de valorizar e tornar estável os precedentes dos Tribunais, em especial das Cortes de Superposição, chegando-se ao ápice de modificar, inclusive, a Constituição do Brasil, para esse fim. Também foi destacada a importância da uniformização de jurisprudência, que de certa maneira precedeu o novel instituto. Na sequência, apontou-se alguns aspectos relevantes, de ordem processual, do incidente, bem como os seus pressupostos de cabimento. Avaliou-se, ainda, um dos mais importantes efeitos que decorrem da admissibilidade do incidente de resolução de demandas repetitivas, no sentido de suspender os demais processos que veiculem idêntica tese jurídica e, também, como se defendeu ao longo do estudo, que guardem similitude de ordem fática. Ademais, especificou-se o procedimento de julgamento, fulcrado, principalmente, em uma notável ampliação do contraditório, que dá margem, inclusive, a que o acórdão prolatado nessa sede possa ser impugnado, via recurso especial e/ou extraordinário. Por fim, encerra-se com a análise do precedente resultante do incidente de resolução de demandas repetitivas. Explicita-se os seus efeitos, inclusive com a possibilidade de aplicação para o futuro, tendo em vista a objetivação do julgamento, voltado à definição de uma tese jurídica. No entanto, e aqui está a Tese defendida, a questão jurídica, ainda que julgada de modo abstrato, justamente para produzir efeitos mais amplos (aqui denominados expansivos), deve estar necessariamente atrelada às questões de fato que a envolvem.

Ação popular e ação de improbidade administrativa na justiça do trabalho

O presente estudo é resultado da observação de que, em que pese o incremento do ajuizamento de ações coletivas na Justiça do Trabalho, por meio de ações civis públicas, ainda há outras ações coletivas, destinadas à defesa de direitos metaindividuais, que não vêm recebendo o mesmo tratamento. Em especial, as ações cuja pretensão é a tutela dos atos da Administração Pública, que, no contexto do Estado Democrático de Direito, deve conduzir-se em prol do bem comum e, ainda, da garantia dos direitos sociais reconhecidos constitucionalmente. Analisa-se o cabimento dessa tutela pela via do Judiciário Trabalhista, nas situações em que os fatos constantes nas causas de pedir das respectivas ações sejam atinentes a direitos relacionados ao trabalho. Isso porque, na ocorrência de pontos de interseção entre o ato administrativo e as relações de trabalho, o ramo do Judiciário constitucionalmente vocacionado a analisá-los é o Trabalhista, já que o interesse em questão não configura mero ato administrativo, mas, além disso, revela o modo como o agente estatal compreende e orienta a sua conduta, gerando a valorização ou a desvalorização de direitos trabalhistas consagrados pela Constituição Federal. Com base nesse panorama acerca do papel do Estado brasileiro contemporâneo no que diz respeito à garantia de direitos sociais e do papel do Poder Judiciário no que tange à efetivação desses direitos, bem como procedendo ao exame da natureza desses direitos, que requerem novas posturas dos operadores do direito, este trabalho se propõe a afastar concepções antigas relacionadas a argumentos de suposta violação à separação de poderes e de indevida interferência em políticas públicas. Com isso, considerando que o Poder Judiciário tem no processo seu locus de manifestação, abordam-se as principais características do processo coletivo, visando à sua diferenciação em relação ao processo individual, em face da natureza dos direitos que compõem o seu objeto. Com o foco no fortalecimento do Judiciário Trabalhista e aperfeiçoamento do Estado Democrático de Direito, ingressa-se na seara das ações populares e de improbidade administrativa, refinando-se a aplicabilidade delas a atos praticados pela Administração Pública que repercutem na esfera trabalhista. Adota-se como premissa a nova conformação dos limites da competência da Justiça do Trabalho que não mais se restringe a lides de natureza individual ou coletiva entre trabalhadores e seus tomadores de serviço, conformação essa introduzida pela Emenda Constitucional no 45/2004 para defender-se que a consecução do bem comum, levada a efeito com a observância aos princípios regentes da Administração, desafia uma nova visão, especializada no valor social do trabalho, inclusive no que se refere à qualidade dos serviços públicos. As questões apontadas possibilitam concluir sobre a necessidade de se instituir concretamente os conteúdos axiológicos e não meramente patrimoniais que compõem o patrimônio público social, em especial o valor social do trabalho, preservando-o ou restituindo-o à coletividade, por meio de ações populares e de improbidade administrativa ajuizadas perante a Justiça do Trabalho. A pesquisa mostra que se alarga a garantia ao cidadão no que tange ao uso dos valores e recursos públicos para a promoção do bem comum e a evolução da coletividade.

Palermo, Italy, 1891 (Raster Image)

This layer is a georeferenced raster image of the historic paper map entitled: Nuova pianta della città di Palermo. It was published by Carlo Clausen, editore in 1891. Scale 1:10,000. Covers a portion of Palermo, Italy. Map in Italian.The image inside the map neatline is georeferenced to the surface of the earth and fit to the European Datum 1950, Universal Transverse Mercator (UTM) Zone 33N projected coordinate system. All map collar and inset information is also available as part of the raster image, including any inset maps, profiles, statistical tables, directories, text, illustrations, index maps, legends, or other information associated with the principal map. This map shows features such as roads, railroads and stations, drainage, built-up areas, selected buildings, parks, ground cover, shoreline features, and more. Includes index. Relief shown by shading.This layer is part of a selection of digitally scanned and georeferenced historic maps from the Harvard Map Collection. These maps typically portray both natural and manmade features. The selection represents a range of originators, ground condition dates, scales, and map purposes.

Genoa, Italy, 1910 (Raster Image)

This layer is a georeferenced raster image of the historic paper map entitled: Nuova pianta topografica della città e del porto di Genova : secondo gli ultimi lavori stradali con il percorso dei trams. It was published by A. P. Editore in 1910. Scale [ca. 1:7,000]. Covers Genoa, Italy. Map in Italian.The image inside the map neatline is georeferenced to the surface of the earth and fit to the European Datum 1950, Universal Transverse Mercator (UTM) Zone 32N projected coordinate system. All map collar and inset information is also available as part of the raster image, including any inset maps, profiles, statistical tables, directories, text, illustrations, index maps, legends, or other information associated with the principal map. This map shows features such as roads, railroads and stations, street railways, drainage, built-up areas and selected buildings, fortification, wharves, docks, gardens, and more. Relief shown by hachures.This layer is part of a selection of digitally scanned and georeferenced historic maps from the Harvard Map Collection. These maps typically portray both natural and manmade features. The selection represents a range of originators, ground condition dates, scales, and map purposes.

Rome, Italy, 1823 (Raster Image)

This layer is a georeferenced raster image of the historic paper map entitled: Nuova pianta di Roma Moderna, estratta dalla grande del Nolli corretta ed accresciuta de nomi delle contrade indicati al loro rispettivo sito in Roma; Pietro Ruga incise. It was published by Venanzio Monaldini Libraio e Cartolaro in 1823. Scale [ca. 1:9,120]. Covers Rome, Italy and Vatican City. The image inside the map neatline is georeferenced to the surface of the earth and fit to the "European Datum 1950 UTM Zone 33N" coordinate system. All map collar and inset information is also available as part of the raster image, including any inset maps, profiles, statistical tables, directories, text, illustrations, index maps, legends, or other information associated with the principal map. This map shows features such as roads, drainage, city districts, walls, gates, and fortifications, selected buildings, and more. Relief is shown by hachures. Includes index and inset plans: Pianta della Chiesa di S. Lorenzo fuori le mura -- Mausoleo di S. Costanza -- Pianta della Basilica di S. Paolo -- Pianta del Pantheon, degli avanzi delle Terme di Agrippa, e dé ruderi scoperti recentemente. This layer is part of a selection of digitally scanned and georeferenced historic maps from The Harvard Map Collection as part of the Imaging the Urban Environment project. Maps selected for this project represent major urban areas and cities of the world, at various time periods. These maps typically portray both natural and manmade features at a large scale. The selection represents a range of regions, originators, ground condition dates, scales, and purposes.

Design and Implementation of a Cloud-based Middleware for Persuasive Android Applications

Negli ultimi decenni, le tecnologie e i prodotti informatici sono diventati pervasivi e sono ora una parte essenziale delle nostre vite. Ogni giorno ci influenzano in maniera più o meno esplicita, cambiando il nostro modo di vivere e i nostri comportamenti più o meno intenzionalmente. Tuttavia, i computer non nacquero inizialmente per persuadere: essi furono costruiti per gestire, calcolare, immagazzinare e recuperare dati. Non appena i computer si sono spostati dai laboratori di ricerca alla vita di tutti i giorni, sono però diventati sempre più persuasivi. Questa area di ricerca è chiamata pesuasive technology o captology, anche definita come lo studio dei sistemi informatici interattivi progettati per cambiare le attitudini e le abitudini delle persone. Nonostante il successo crescente delle tecnologie persuasive, sembra esserci una mancanza di framework sia teorici che pratici, che possano aiutare gli sviluppatori di applicazioni mobili a costruire applicazioni in grado di persuadere effettivamente gli utenti finali. Tuttavia, il lavoro condotto dal Professor Helal e dal Professor Lee al Persuasive Laboratory all’interno dell’University of Florida tenta di colmare questa lacuna. Infatti, hanno proposto un modello di persuasione semplice ma efficace, il quale può essere usato in maniera intuitiva da ingegneri o specialisti informatici. Inoltre, il Professor Helal e il Professor Lee hanno anche sviluppato Cicero, un middleware per dispositivi Android basato sul loro precedente modello, il quale può essere usato in modo molto semplice e veloce dagli sviluppatori per creare applicazioni persuasive. Il mio lavoro al centro di questa tesi progettuale si concentra sull’analisi del middleware appena descritto e, successivamente, sui miglioramenti e ampliamenti portati ad esso. I più importanti sono una nuova architettura di sensing, una nuova struttura basata sul cloud e un nuovo protocollo che permette di creare applicazioni specifiche per smartwatch.

Individuazione del danno su ponti in muratura mediante misure dinamiche

La diagnostica strutturale è un campo in continuo sviluppo e attualmente sono numerosi gli studi tendenti alla definizione di tecniche e metodi in grado di fornire parametri che possano identificare, in modo sempre più accurato, lo stato di sicurezza di una struttura. Stato di sicurezza è un termine globale che si riferisce alla capacità portante di una struttura e alla sua resistenza alle sollecitazioni esterne, siano esse statiche o dinamiche. Per tanto, un qualsiasi danneggiamento strutturale potrebbe in varia misura influenzare tale stato. Per quanto riguarda i ponti stradali, negli ultimi anni l’attenzione è stata focalizzata allo studio di metodi di individuazione del danno a partire dai risultati ottenuti dal monitoraggio delle vibrazioni mediante accelerometri. Questo è stato possibile grazie agli avanzamenti raggiunti nell’identificazione modale e nei sensori per il monitoraggio strutturale. Questo lavoro si pone come obiettivo quello di proporre una nuova metodologia di analisi dei dati ottenuti da indagini sperimentali che possono essere svolte in sito. La definizione di tale metodologia è affidata a simulazioni numeriche volte a rappresentare stati di danneggiamento avanzati su elementi strutturali. In una prima fase verranno analizzati elementi semplificati rappresentativi di strutture esistenti, come ad esempio travi da ponte in calcestruzzo armato. In una seconda fase, il metodo verrà testato su modelli più complessi che tengano conto della tridimensionalità del problema, oltre alle variazioni sezionali e di materiali degli elementi che lo compongono.

HTML5, Javascript and modern browser technologies: toward a web based framework for device fingerprinting

Mentre navighiamo siamo veramente certi che i nostri dati e la nostra privacy siano al sicuro? I browser e le tecnologie di cui fanno uso possono rivelare una miriade di informazioni. Al crescere delle informazioni reperibili, si inizia a superare una massa critica che può permettere l'identificazione. Il device fingerprinting è proprio il rilevamento di questa tipologia di dati. HTML5 e le nuove API che esso mette a disposizione aumentano a dismisura le modalità per fare fingerprinting. Durante lo sviluppo della presente tesi è stato realizzato un framework molto potente che verrà mostrato nel dettaglio. Come a seguito di un disastro aereo, l'ingegneria aeronautica si mette all'opera per scovare i punti deboli allo scopo di rendere più robusti gli aerei di nuova generazione, noi con la presente tesi vogliamo dare il nostro contributo al miglioramento del web del futuro. Affinchè la nostra privacy sia veramente nelle nostre mani e possiamo essere artefici del nostro domani.