Laser pulse induced bumps in chalcogenide phase change films

Formation of bumps in chalcogenide phase change thin films during the laser writing process is theoretically and experimentally investigated. The process involves basically fast heating and quenching stages. Circular bumps are formed after cooling, and the shape and size of the bumps depend on various parameters such as temperatures, laser power, beam size, laser pulse duration, etc. In extreme cases, holes are formed at the apex of the bumps. To understand the bumps and their formation is of great interest for data storage. In the present work, a theoretical model is established for the formation process, and the geometric characters of the formed bumps can be analytically and quantitatively evaluated from various parameters involved in the formation. Simulations based on the analytic solution are carried out taking Ag8In14Sb55Te23 as an example. The results are verified with experimental observations of the bumps. (C) 2008 American Institute of Physics.

输出高重复频率脉冲列的全固态激光器

报道了利用声光振幅调制锁模的方法，在激光二极管端面抽运Nd：YVO4激光器上获得320MHz高重复频率脉冲列的实验结果。实验采用平一平腔结构，腔长452mm，耦合输出镜透过率为3．6％。所用声光介质为熔融石英晶体，以铌酸锂作换能器，在驱动功率4．5W时，对1064nm波长衍射效率为50，相应的调制深度为0．31。在最佳锁模状态下，激光二极管抽运功率为3．5W，此时激光平均输出功率为15mw。示波器记录脉冲宽度680ps，实测光束质量因子M^2小于1．5。并在实验基础上对激光器工作的稳定性进行了分析，结果表

星载激光对水下目标通信可行性研究

The characteristics of media in communication channel are analyzed briefly and the reasonable optical parameters of media are adopted. With certain communication system parameters the temporal and spatial distributions of the received signal from submerged platform are simulated using Monte Carlo method. The upper limit of the ratio of Monte Carlo estimated error to averaged value is about 0.3%. From the simulated results, the optimized sampling timing of receiver and field of view of telescope are obtained. Also the signal-to-noise ratio of the receiver is calculated. Based on this, the error probability of the communication system is deduced from laser pulse position modulation and maximum likelihood detection. The results show that under severe environment robust laser communication from a satellite to a submerged platform can be achieved.

Excimer laser plasma to control laser pulse duration

An injection-locking excimer laser beam with a pulse duration of 25 ns is focused on the surface of a polymide film. The laser beam that passes through the etching film is shorter than the original one. By optimizing the thickness of the film and the beam power density, a pulse with a 3-ns pulse duration can be obtained using this switch technology.

A Q-swicthed all-solid-state single-longitudinal-mode laser with adjustable pulse-width and high repetition rate

A single-longitudinal-mode (SLM) laser-diode pumped Nd: YAG laser with adjustable pulse width is developed by using the techniques of pre-lasing and changing polarization of birefingent crystal. The Q-switching voltage is triggered by the peak of the pre-lasing pulse to achieve the higher stability of output pulse energy. The output energy of more than 1 mJ is obtained with output energy stability of 3% (rms) at 100 Hz. The pulse-width can be adjusted from 30 ns to 300 ns by changing the Q-switching voltage. The probability of putting out single-longitudinal-mode pulses is almost 100%. The laser can be run over four hours continually without mode hopping.

Stable pulse-compressed acousto-optic Q-switched fiber laser

A novel acousto-optic switch operation by a simple laser-diode pumped acousto-optic, Q-switched, ytterbium-doped, double-clad fiber laser is reported. Stable compressed Q-switched sub-40 ns pulses with a beam quality factor (M-2 = 2) are achieved at the repetition rate of 1-50 kHz. Q-switched pulses of similar to 20 mu J pulse energy and 35 as pulse width are obtained at the repetition rate of 50 kHz. Finally, a reasonable explanation of the novel Q-switched operation is presented. (c) 2007 Optical Society of America.

20-W average power, high repetition rate, nanosecond pulse with diffraction limit from an all-fiber MOPA system

In this article, we report an all-fiber master oscillator power amplifier (MOPA) system, which can provide high repetition rate and nanosecond pulse with diffraction-limit. The system was constructed using a (2 + 1) X 1 multimode combiner. The Q-Switched, LD pumped Nd:YVO4 solid-state laser wets used (is master oscillator. The 976-nm fiber-coupled module is used as pump source. A 10-m long China-made Yb3+-doped D-shape double-clad large-mode-area fiber was used as amplifier fiber. The MOPA produced as much as 20-W average power with nanosecond pulse and near diffraction limited. The pulse duration is maintained at about 15 its during 50-175 kHz. The system employs a simple and compact architecture and is therefore suitable for the use in practical applications such as scientific and military airborne LIDAR and imaging. Based oil this system. the amplification performances of. the all fiber amplifier is investigated. (C) 2008 Wiley Periodicals, Inc.