Mineral partitioning in milk and milk permeates at high temperature

The soluble phase of milk was separated at 20 and 80°C using ultrafiltration. The resulting permeates were then subjected to further ultrafiltration and dialysis at close to these two temperatures. It was found that pH, Ca2+ and soluble Ca decreased as the separation temperature increased both in original UF permeates and in dialysates obtained from these permeates, but P decreased only slightly. The major reason for these changes was due to the precipitation of calcium phosphate/citrate complexes onto the casein micelle with concomitant release of H+. The pH of both permeates and dialysates from milk at 20°C were slightly higher than for milk. When UF permeates collected at 20 and 80°C, were each dialysed at both these temperatures, the dialysate collected at 80°C showed much less temperature dependence for pH and ionic calcium compared with that collected at 20°C. This is in contrast to milk, which shows considerable temperature dependence for pH and ionic calcium. Further experiments revealed that the pH and Ca2+ concentration of permeates showed high temperature dependence above the temperature at which they were separated, but a much lower temperature dependence below that temperature. These findings suggest that dialysis and UF of milk at high temperature provide the best means yet for estimating the pH and ionic calcium of milk at that temperature.

Mixed copper, silver, and gold cyanides, (MxM′1–x)CN: tailoring chain structures to influence physical properties

Binary mixed-metal variants of the one-dimensional MCN compounds (M = Cu, Ag, and Au) have been prepared and characterized using powder X-ray diffraction, vibrational spectroscopy, and total neutron diffraction. A solid solution with the AgCN structure exists in the (CuxAg1–x)CN system over the range (0 ≤ x ≤ 1). Line phases with compositions (Cu1/2Au1/2)CN, (Cu7/12Au5/12)CN, (Cu2/3Au1/3)CN, and (Ag1/2Au1/2)CN, all of which have the AuCN structure, are found in the gold-containing systems. Infrared and Raman spectroscopies show that complete ordering of the type [M–C≡N–M′–N≡C−]n occurs only in (Cu1/2Au1/2)CN and (Ag1/2Au1/2)CN. The sense of the cyanide bonding was determined by total neutron diffraction to be [Ag–NC–Au–CN−]n in (Ag1/2Au1/2)CN and [Cu–NC–Au–CN−]n in (Cu1/2Au1/2)CN. In contrast, in (Cu0.50Ag0.50)CN, metal ordering is incomplete, and strict alternation of metals does not occur. However, there is a distinct preference (85%) for the N end of the cyanide ligand to be bonded to copper and for Ag–CN–Cu links to predominate. Contrary to expectation, aurophilic bonding does not appear to be the controlling factor which leads to (Cu1/2Au1/2)CN and (Ag1/2Au1/2)CN adopting the AuCN structure. The diffuse reflectance, photoluminescence, and 1-D negative thermal expansion (NTE) behaviors of all three systems are reported and compared with those of the parent cyanide compounds. The photophysical properties are strongly influenced both by the composition of the individual chains and by how such chains pack together. The NTE behavior is also controlled by structure type: the gold-containing mixed-metal cyanides with the AuCN structure show the smallest contraction along the chain length on heating.

Molecular recognition between functionalized gold nanoparticles and healable, supramolecular polymer blends – a route to property enhancement

A new, healable, supramolecular nanocomposite material has been developed and evaluated. The material comprises a blend of three components: a pyrene-functionalized polyamide, a polydiimide and pyrenefunctionalized gold nanoparticles (P-AuNPs). The polymeric components interact by forming well-defined p–p stacked complexes between p-electron rich pyrenyl residues and p-electron deficient polydiimide residues. Solution studies in the mixed solvent chloroform–hexafluoroisopropanol (6 : 1, v/v) show that mixing the three components (each of which is soluble in isolation), results in the precipitation of a supramolecular, polymer nanocomposite network. The precipitate thus formed can be re-dissolved on heating, with the thermoreversible dissolution/precipitation procedure repeatable over at least 5 cycles. Robust, self-supporting composite films containing up to 15 wt% P-AuNPs could be cast from 2,2,2- trichloroethanol. Addition of as little as 1.25 wt% P-AuNPs resulted in significantly enhanced mechanical properties compared to the supramolecular blend without nanoparticles. The nanocomposites showed a linear increase in both tensile moduli and ultimate tensile strength with increasing P-AuNP content. All compositions up to 10 wt% P-AuNPs exhibited essentially quantitative healing efficiencies. Control experiments on an analogous nanocomposite material containing dodecylamine-functionalized AuNPs (5 wt%) exhibited a tensile modulus approximately half that of the corresponding nanocomposite that incorporated 5 wt% pyrene functionalized-AuNPs, clearly demonstrating the importance of the designed interactions between the gold filler and the supramolecular polymer matrix.

Whey protein mouth drying influenced by thermal denaturation

Whey proteins are becoming an increasingly popular functional food ingredient. There are, however, sensory properties associated with whey protein beverages that may hinder the consumption of quantities sufficient to gain the desired nutritional benefits. One such property is mouth drying. The influence of protein structure on the mouthfeel properties of milk proteins has been previously reported. This paper investigates the effect of thermal denaturation of whey proteins on physicochemical properties (viscosity, particle size, zeta-potential, pH), and relates this to the observed sensory properties measured by qualitative descriptive analysis and sequential profiling. Mouthcoating, drying and chalky attributes built up over repeated consumption, with higher intensities for samples subjected to longer heating times (p < 0.05). Viscosity, pH, and zeta-potential were found to be similar for all samples, however particle size increased with longer heating times. As the pH of all samples was close to neutral, this implies that neither the precipitation of whey proteins at low pH, nor their acidity, as reported in previous literature, can be the drying mechanisms in this case. The increase in mouth drying with increased heating time suggests that protein denaturation is a contributing factor and a possible mucoadhesive mechanism is discussed.

On site flotation for recovering polluted aquatic systems: is it a feasible solution for a Brazilian urban river?

Pinheiros River (Brazil) plays a pivotal role in supplying water to Billings Reservoir, which presents multiple uses (human drinking, energy generation, irrigation, navigation, fishing and leisure) An intense monitoring program was performed during the years 2007 and 2008 to find out whether on site flotation is a feasible solution or not for improving the water quality of this urban river, attenuating the pollutants load caused by the water pumping to the reservoir (approximately 10 m(3)s(-1)) The monitoring of 18 variables (13,429 laboratorial analysis during the period of 490 days), suggested that despite the convenience of the on site approach for water treatment, especially for rivers located in fully urbanized areas, the flotation system is not enough itself to recover Pinheiros River water quality, given the several constraints that apply Total phosphorus removal was high in percentage terms (about 90%), although the remaining concentrations were not so low (mean of 0 05 mg L(-1)) The removal efficiency of some variables was insufficient, leading to high final mean concentrations of metals [e g aluminium (0 29 mg L(-1)), chromium (0 02 mg L(-1)) and iron (1 1 mg L(-1))] as well as nitrogen-ammonia (25 8 mg L(-1)) and total suspended solids (18 mg L(-1)) in the treated water

Elastase secretion in Acanthamoeba polyphaga

Acanthamoeba species are frequently isolated from soil and water collections. In the environment, the organisms multiply as phagotrophic trophozoites and encyst under adverse conditions. Several species are known to infect man, causing keratitis and opportunistic diseases. The mechanisms underlying tissue damage and invasion by the amoebae are being elucidated and the involvement of secreted peptidases, particularly serine peptidases, has been demonstrated. Here, elastase activity was examined in Acanthamoeba-conditioned medium (ACM), making use of elastin-Congo red (ECR) and synthetic peptide p-nitroanilide substrates. ACM hydrolysed ECR over a broad pH range and optimally at a pH of 7.5 and above. Indicating the activity of serine and metallopeptidases, Congo red release was potently inhibited by PMSF, antipain, chymostatin and 1,10-phenanthroline, partially reduced by elastatinal and EDTA, and unaffected by 1,7-phenanthroline and E-64. Screening with synthetic substrates mainly showed the activity of serine peptidases. ACM efficiently hydrolysed Suc-Ala(2)-Pro-Leu-pNA and Suc-Ala(2)-Pro-Phe-pNA over a broad pH range (7.0-9.5) and was weakly active against Suc-Ala(3)-pNA, a substrate found to be optimally hydrolysed at a pH around 7.0. Following ammonium sulfate precipitation of ACM proteins and FPLC analysis, the majority of the ECR-splitting activity, characterised as serine peptidases, bound to CM-sepharose and co-eluted with part of the Suc-Ala(2)-Pro-Phe-pNA-hyd to lysing activity in a gradient of 0-0.6 M NaCl. In the corresponding FPLC fractions, serine peptidases resolving in the region of 70-130 kDa were detected in gelatin gels. Overall, the results demonstrate that trophozoites secrete elastases, and additionally suggest the high molecular weight serine peptidases as possible elastase candidates. (C) 2009 Elsevier B.V. All rights reserved.

A vaccine against S. pyogenes: Design and experimental immune response

Streptococcus pyogenes causes severe invasive infections: the post-streptococcal sequelae of acute rheumatic fever (RF) and rheumatic heart disease (RHD), acute glomerulonephritis, and uncomplicated pharyngitis and pyoderma. Efforts to produce a vaccine against S. pyogenes began several decades ago, and different models have been proposed. Here, we describe the methodology used in the development of a new vaccine model, consisting of both T and B protective epitopes constructed as synthetic peptides and recombinant proteins. Two adjuvants were tested in an experimental inbred mouse model: a classical Freund`s adjuvant and a new adjuvant (AFCo1) that induces mucosal immune responses and is obtained by calcium precipitation of a proteoliposome derived from the outer membrane of Neisseria meningitides B. The StreptInCor vaccine epitope co-administrated with AFCo1 adjuvant induced mucosal (IgA) and systemic (IgG) antibodies as preferential Th1-mediated immune responses. No autoimmune reactions were observed, suggesting that the vaccine epitope is safe. (c) 2009 Elsevier Inc. All rights reserved.

Ionic Recognition by 7-Nitro-1,3,5-triaza Adamantane: First Thermodynamic Study

A thermodynamic study involving 7-nitro-1,3,5-triaza adamantane, 1, and its interaction with metal cations in nonaqueous media is first reported. Solubility data of 1 in various solvents were used to derive the standard Gibbs energies of solution, Delta G(s)degrees in these solvents. The effect of solvation in the different media was assessed from the Gibbs energy of transfer taking acetonitrile as a reference solvent. (1)H NMR studies of the interaction of 1 and metal cations were carried out in CD(3)CN and CD(3)OD and the data are reported. Conductance measurements revealed that this ligand forms lead(II) or zinc complexes of 1: 1 stoichiometry in acetonitrile. It also revealed a stoichiometry of two molecules of 1 per mercury(II) and two cadmiu (II) ions per molecule of 1. The addition of silver salt to 1 led to the precipitation of the silver-1 complex which was isolated and characterized by X-ray crystallography. At variance with conductance measurements in solution, in the solid state the X-ray structure show`s a 1:1 stoichiometry in the Hg(II) complex. The themiodynamics of complexation of 1 and these cations provide a quantitative assessment of the selective behavior of this ligand for ions of environmental relevance.

Peat as a natural solid-phase for copper preconcentration and determination in a multicommuted flow system coupled to flame atomic absorption spectrometry

The physical and chemical characteristics of peat were assessed through measurement of pH, percentage of organic matter, cationic exchange capacity (CEC), elemental analysis, infrared spectroscopy and quantitative analysis of metals by ICP OES. Despite the material showed to be very acid in view of the percentage of organic matter, its CEC was significant, showing potential for retention of metal ions. This characteristic was exploited by coupling a peat mini-column to a flow system based on the multicommutation approach for the in-line copper concentration prior to flame atomic absorption spectrometric determination. Cu(II) ions were adsorbed at pH 4.5 and eluted with 0.50 mol L(-1) HNO(3). The influence of chemical and hydrodynamic parameters, such as sample pH, buffer concentration, eluent type and concentration, sample flow-rate and preconcentration time were investigated. Under the optimized conditions, a linear response was observed between 16 and 100 mu g L(-1), with a detection limit estimated as 3 mu g L(-1) at the 99.7% confidence level and an enrichment factor of 16. The relative standard deviation was estimated as 3.3% (n = 20). The mini-column was used for at least 100 sampling cycles without significant variation in the analytical response. Recoveries from copper spiked to lake water or groundwater as well as concentrates used in hemodialysis were in the 97.3-111 % range. The results obtained for copper determination in these samples agreed with those achieved by graphite furnace atomic absorption spectrometry (GFAAS) at the 95% confidence level. (C) 2009 Elsevier B.V. All rights reserved.

CuO and CuO-ZnO catalysts supported on CeO(2) and CeO(2)-LaO(3) for low temperature water-gas shift reaction

This paper describes an investigation on CuO and CuO-ZnO catalysts supported on CeO(2) and CeO(2)-La(2)O(3) oxides, which were designed for the low temperature water-gas shift reaction (WGSR). Bulk catalysts were prepared by co-precipitation of metal nitrates and characterized by energy-dispersive spectroscopy (EDS), X-ray diffraction (XRD), surface area (by the BET method), X-ray photoelectron spectroscopy (XPS), and in situ X-ray absorption near edge structure (XANES). The catalysts` activities were tested in the forward WGSR, and the CuO/CeO(2) catalyst presented the best catalytic performance. The reasons for this are twofold: (1) the presence of Zn inhibits the interaction between Cu and Ce ions, and (2) lanthanum oxide forms a solid solution with cerium oxide, which will cause a decrease in the surface area of the catalysts. Also the CuO/CeO(2) catalyst presented the highest Cu content on the surface, which could influence its catalytic behavior. Additionally, the Cu and Cu(1+) species could influence the catalytic activity via a reduction-oxidation mechanism, corroborating to the best catalytic performance of the Cu/Ce catalyst. (c) 2010 Elsevier B.V. All rights reserved.

Induktiv provning av ferritiskt rostfritt stå

The report examines the factors which may be a contributing cause to the problems that are present when ferritic stainless steel are eddy current tested in a warm condition. The work is carried out at Fagersta Stainless AB in Fagersta which manufactures stainless steel wire. In the rolling mill there is an eddy current equipment for detection of surface defects on the wire. The ferritic stainless steels cause a noise when testing and this noise complicates the detection of defects.Because of this, a study was made of how the noise related to factors such as steel grade, temperature, size and velocity. By observing the signal and with the possibilities to change the equipment settings the capability to let a signal filter reduce the noise level were evaluated. Theories about the material's physical properties have also been included, mainly the magnetic properties, electrical conductivity and the material's tendency to oxidize.Results from the tests show that a number of factors do not affect the inductive test significantly and to use a filter to reduce the noise level does not seem to be a viable option. The level of noise does not relate to the presence of superficial particles in form of oxides.The ferritic stainless steels showed some difference in noise level. Which noise level there was did match well with the steels probability for a precipitation of a second phase, and precipitation of austenite may in this case contribute to noise when using an eddy current instrument.The noise is probably due to some physical material property that varies within the thread.

Estudo do componente árboreo de mata Ribeirinha no rio Camaquã, Cristal, RS

As matas ribeirinhas no rio Camaquã constituem os maiores remanescentes da Floresta Estacional Semidecidual Ribeirinha no Estado, sendo muito pouco conhecidas florística e fitossociologicamente. Em um fragmento de mata ribeirinha na margem esquerda do baixo rio Camaquã, município de Cristal (31°01’01.7’’S e 51°56’42.0’’W, em torno de 14 m.n.m.) realizou-se um estudo do componente arbóreo, com o intuito de se determinar sua estrutura e relacionar os resultados obtidos com outras florestas no Estado. O clima da região é do tipo Cfa de Köppen, com médias anuais de temperatura de 18,9 °C, e de precipitação de 1.234 mm. Os solos são do tipo Planossolo Hidromórfico Eutrófico (Sge), de textura média/siltosa. O levantamento fitossociológico foi realizado em uma área de 1 ha, dividida em 100 parcelas de 10 x 10 m, onde foram amostradas todas as árvores com DAP maior ou igual a 5 cm. Foram calculados os parâmetros fitossociológicos empregados usualmente, além das estimativas de diversidade de Shannon (H’) e equabilidade de Pielou (J’). Relações florísticas com outras áreas foram feitas através da análise de coordenadas principais e de agrupamento, utilizando os índices de similaridade de Jaccard e Dice. No levantamento florístico foram encontradas 68 espécies arbóreas, a maioria características de ambientes ribeirinhos. Na fitossociologia foram amostrados 2.179 indivíduos, pertencentes a 29 espécies, 25 gêneros e 14 famílias. As famílias Myrtaceae, Euphorbiaceae, Fabaceae, Sapindaceae e Salicaceae apresentaram as maiores riquezas. Os valores de importância mais elevados foram registrados para espécies típicas de sub-bosque, que apresentam grande densidade (Sebastiania commersoniana, Allophylus edulis e Eugenia schuechiana). As espécies ocupantes do dossel, com densidades baixas ou intermediárias (Luehea divaricata e Nectandra megapotamica) destacam-se pela dominância. O índice de diversidade foi estimado em 2,342 nats.ind.-1 (J’= 0,695), sendo intermediário entre os menores valores estimados para as matas de restingas e os maiores para Florestas Estacionais Semideciduais na região. O predomínio de espécies zoocóricas demonstra ser uma floresta madura, embora se tenha encontrado uma grande participação de indivíduos com síndrome de dispersão abióticas. Por sua localização na Planície Costeira Interna, a área apresentou, floristicamente, uma grande influência de espécies provenientes das matas de encosta da Serra do Sudeste, havendo uma maior similaridade com as matas do rio Piratini e outras Florestas Estacionais Semideciduais.

Caracterização hidrológica e geoquímica das áreas adjacentes aos bancos oceânicos do nordeste brasileiro

O objeto deste trabalho é fornecer dados hidrológicos com fins de caracterização e monitoramento da região da Cadeia Norte do Brasil e da Cadeia de Fernando de Noronha, assim como levantar e sistematizar informações sobre a geoquímica dos diversos tipos de sedimentos encontrados na plataforma continental externa adjacente ao banco Aracati, contribuindo para o levantamento dos potenciais sustentáveis de exploração dos recursos vivos da Zona Econômica Exclusiva. A área em estudo compreende a sub-área II, setor 1 e parte do setor 2, e está localizada entre 1oN e 5oS de latitude e entre 30o e 40oW de longitude, abrangendo uma área de aproximadamente 400.000 km2. Foram analisadas amostras coletadas em 8 estações resultando em 20 amostras de sedimentos nos anos de 1997 (verão), 1998 (outono) e 2000 (primavera) e 34 estações que originaram 272 amostras de água na primavera de 2000. As concentrações máximas dos parâmetros analisados, com exceção do fosfato, nas amostras de água se localizam na região próxima à costa. Detectou-se na área uma termoclina bem marcada, sendo mais profunda na primavera. A camada de mistura é bastante homogênea, sendo porém, mais espessa na primavera. O pH detectado encontra-se na faixa alcalina sendo os maiores valores de pH detectados na primavera. Verifica-se, um máximo de salinidade na camada de inicio da termoclina sazonal. Não verificou-se na área condição anaeróbica na coluna d’água. A distribuição de fosfato, nitrato e silicato, apresenta-se de forma muito semelhante, sendo que na primavera essas concentrações são maiores, nas camadas superficiais. Na cobertura sedimentar da plataforma continental adjacente aos bancos da cadeia norte do Brasil, encontro-se areia quartzosa, areia carbonática, fragmentos de concha, Lithothanmium e Halimedas. Os fragmentos de concha apresentaram as maiores concentrações totais de metais, enquanto Lithothanmium apresentou o maior teor de carbonato. Há uma forte correlação entre ferro e manganês na amostras de água e em todas as frações de sedimentos analisadas, sendo que nestas a relação média entre estes elementos é da ordem de 1:25. Existe forte correlação entre cromo e carbonato nas amostras que apresentam teor de carbonato maior que 20%. As amostras de areia quartzosa, fragmentos de concha e Halimedas, apresentam-se muito semelhantes quanto à distribuição de ferro, manganês, zinco e cromo. Existe forte correlação nas amostras de sedimento, assim como nas amostras de água, entre ferro, manganês, zinco, correlacionando-se também nas amostras de sedimento com o chumbo. As 8 concentrações de metais nas amostras de água apresentaram-se relativamente baixas em se comparando com as amostras de sedimento. Nas amostras de água as concentrações de cromo e chumbo estão abaixo do limite de detecção.

Ecologia alimentar e reprodutiva da piaba-do-rabo-amarelo, Astyanax cf. lacustris (Reinhardt, 1874) (Osteichthyes: Characidae) na Lagoa do Piató, Assu, Rio Grande do Norte, Brasil

The feeding habits and biological aspects of the reproductive cycle of two-spot astyanax, Astyanax cf. lacustris (Reinhardt, 1874) were investigated. Fish samples were captured on a monthly basis, using gillnets of 4 cm mesh size, from the Piató Lake, Assu, Rio Grande do Norte, during the period of September, 2006 to August, 2007. Physico-chemical parameters, such as, temperature, electrical conductivity and dissolved oxygen of the lake were registered. The monthly values of rainfall also were obtained. The 360 individuals captured, were measured, weighed, dissected, and stomach weight and the stage of gonadal maturity were registered. The stomach contents analyses were carried out based on volumetric method, points, frequency of occurrence and applying the Index of Relative Importance. The degrees of repletion of the stomachs were determined besides the Index of Repletion relating to feeding activity variations and frequency of ingestion with limnological parameters and rainfall. The food items identified were separated into distinct groups according to their origin. Sex ratio and Gonadosomatic Relation of females were verified to determine the spawning period and fecundity. The physico-chemical parameters presented the following annual mean values: temperature = 28.8ºC, electrical conductivity = 992.5 µS.cm-1; dissolved oxygen = 4.9 mg.L-1 during the study period. The annual mean of the rainfall was 63.5 mm. The results indicate that this species present an omnivorous feeding habit with a tendency towards insectivory, with an increase in feeding activity during the dry season. The aquatic oxygen to interfere very importance in the feeding activity than the others factors physico-chemicals of water and rainfall. There was a predominance of females, with a sex proportion of 1M:7F. The macroscopic characteristics of the ovaries and testicles revealed four stages of gonadal development: immature, maturing, mature and spent. A temporal variation was observed for the gonadal development of males and females. There was reproductive activity through out the year, with peaks in the months of February, April and June to correspond with the rain of precipitation of the region. The mean fecundity was 7.681 mature oocytes, varying from 4.476 to 12.036, with mean of 7.681. There was positive relation between fecundity and body mass. Condition Factor is not an efficient indicator of the reproductive period of this species. The species A. cf. lacustris is an opportunist and is well adapted to the conditions of the semi-arid Caatinga Biome

Análise e avaliação dos elementos de penetração no solo de equipamentos rodoviários após revestimento

The main objective is to analyze the abrasive wear resistance to the low stress of the elements that make up the organs of road machinery that are exposed directly to contact with abrasives. These samples were analyzed after these elements are coated superficially by the process of welding electrode coated with (SAER) and the manual process of coating type LVOF thermal spraying. As well, is to provide suggestions for a better recovery and return of these elements, which are reducing costs and avoiding downtime in the fronts of service. The samples were made from a substrate of carbon ABNT 1045 tempered steel, following the same specifications and composition of metals and alloys of constituents was followed the standard governing the dimensions of these samples and in accordance with the corresponding size. The results were evaluated by testing the hardness, abrasion resistance to wear by the low stress and the loss of volume involving the microstructure of coatings analyzed