980 resultados para Motore Diesel turbocompressore
Resumo:
A la física o a l’enginyeria es defineix com fregament o fricció a la resistència que s'oposa a la rotació o al lliscament d'un cos sobre un altre, o també a la força que apareix en la superfície de contacte de dos cossos quan s'intenta lliscar un sobre un altre. El fregament ha estat fins avui dia un gran problema físic, això és degut a que genera imperfeccions, especialment microscòpiques, entre les superfícies en contacte. Aleshores és quan apareix la tribologia. La tribologia és la ciència que estudia la fricció, el desgast i la lubricació de superfícies en contacte. El lliscament entre superfícies sòlides es caracteritza generalment per un alt coeficient de fricció i un gran desgast a causa de les propietats específiques de les superfícies. La lubricació consisteix en la introducció d'una capa intermèdia d'un material aliè entre les superfícies en moviment. En aquest projecte hem intentat aplicar tècniques i mètodes de control els quals puguin arribar a millorar i perfeccionar els sistemes de mesura i control a nivell industrial i/o particular. En el nostre cas ha estat l’estudi dels olis lubricants usats en motors de combustió interna de variats vehicles com motocicletes, automòbils, camions o vaixells. Hem introduït una millora d’automatització mitjançant un circuit pneumàtic al captador de partícules, hi hem introduït una tècnica per captar partícules a partir de filtres de membrana, hem estudiat les mostres i llurs ferrogrames i membranes amb la finalitat de detectar les anomalies dels motors. L’objectiu del treball és l’estudi del desgast originat en motors de combustió interna, majoritàriament, Dièsel de camions, automòbils i vaixells. Això, comprèn la captació de partícules en ferrografies, la seva observació i anàlisi en microscopi, la seva classificació, comparació i la detecció d’anomalies en els motors. Per altra banda, també s’aprofundirà en les tècniques d’anàlisi, la lubricació i manteniment dels motors i el nou disseny i validació d’un captador de partícules automatitzat
Resumo:
Introducción: la contaminación atmosférica no solo tiene efectos sobre el sistema respiratorio sino también sobre el cardiovascular. El objetivo de este estudio es generar evidencia que permita establecer una asociación entre el infarto agudo del miocardio y la concentración de PM10 en el ambiente como un estudio preliminar para un grupo de pacientes en Bogotá. Metodología: la asociación entre la concentración del material particulado (en este caso PM10 medido en la estación más cercana del lugar reportado por el paciente) y el infarto agudo del miocardio se estableció utilizando el diseño case crossover. Se utilizó información de las historias clínicas de los pacientes con infarto agudo del miocardio que ingresaron al Servicio de Urgencias de la FSFB, y las concentraciones de PM10 medido en la estación más cercana al lugar de inicio de los síntomas de síndrome coronario agudo, reportado por el paciente. Resultados: se encontró que la asociación entre la concentración de PM10 y el diagnóstico de infarto agudo del miocardio es estadísticamente significativa teniendo en cuenta tres momentos de control: 2 horas antes del evento, 24 horas antes del evento y 48 horas antes del evento. Discusión: este estudio sugiere que las altas concentraciones de material particulado en el ambiente son un factor de riesgo para el desarrollo de infarto agudo del miocardio especialmente en personas con enfermedad coronaria subyacente. Con esta investigación se demuestra la importancia de generar acciones que disminuyan la contaminación de la ciudad y de esta forma proteger la salud de las personas.
Resumo:
Introducción. Los pintores de vehículos automotores están expuestos a solventes puros o mezclas de estos, los cuales se han asociado con efectos neurológicos y mutacarcinogénicos. Materiales y Métodos. Se realizó un estudio descriptivo de corte transversal para caracterizar las condiciones de salud y trabajo de individuos expuestos a solventes orgánicos en talleres de lámina y pintura en Bogotá. Se comparó un grupo de expuestos a solventes orgánicos con un grupo no expuestos. Se determinaron concentraciones de benceno, tolueno y xileno (BTX) en aire, se aplicó una encuesta individual y se midieron en orina, los ácidos fenil mercaptúrico, hipúrico, orto-para metilhipúrico como metabolitos de benceno, tolueno y xileno. Los resultados de las mediciones y de la encuesta se correlacionaron para establecer el panorama de exposición. Resultados: hubo diferencias estadísticamente significativas entre la población expuesta y la población no expuesta a solventes (p = 0,00) para los tres metabolitos de BTX. Se encontraron correlaciones positivas entre el tolueno en aire y ácido hipúrico en orina de los expuestos, (Spearman de 0,82) y entre el xileno en aire y el ácido o-metilhipúrico (Spearman de 0,76). Se encontraron valores de ácido hipúrico por encima de los límites permisibles en 11 2 trabajadores y de ácido p-metilhipúrico en 8 de ellos. No hubo valores para ácido fenilmercapturico fuera de límite. Discusión: los pintores de carros se encuentran expuestos a niveles altos de solventes orgánicos en sus sitios de trabajo y no cuentan con condiciones adecuadas de higiene y seguridad industrial para realizar sus labores.
Resumo:
Objetivo Realizar una revisión sistemática de la neumonía lipoidea exógena (NLE) con el propósito de compactar y sintetizar los conocimientos fragmentados, así como el de informar el estado actual de este tema como riesgo laboral. Metodología La neumonía lipoidea es una condición poco común que resulta de la presencia de lípidos en el interior del espacio alveolar, se desconoce su actual incidencia. La neumonía lipoidea exógena se produce por aspiración o inhalación de sustancias oleosas, es una patología rara en pacientes sin enfermedades de base que predispongan a la broncoaspiración y cuando se presenta en individuos sanos se debe sospechar un origen ocupacional. Se realizó una revisión de literatura según la metodología estandarizada, incluyendo en la búsqueda: reporte de casos, descripciones de la enfermedad y el uso de técnicas diagnósticas. Las bases de datos fueron OVID además de GOOGLE ACADÉMICO; buscadores específicos: MEDLINE, CHEST, PUB MED, REDALYC, SCIELO, Europe PubMed Central (Europe PMC) y ELSEVIER. La búsqueda estuvo además, orientada por una serie de preguntas orientadoras sobre la neumonía lipoidea exógena (NLE) como riesgo laboral. Los artículos que cumplieron con los criterios de inclusión, se clasificaron de acuerdo con tipo de estudio, la calidad del artículo y finalmente se evaluaron con base en una lista de chequeo ajustada para este fin. Resultados Se seleccionó un total de 71 estudios incluyendo reporte de casos, descripciones de la enfermedad y técnicas diagnósticas; publicaciones provenientes de 21 países. Un total de 63 casos, 31 en mujeres (49,20%) y 32 en hombres (50,8%) fueron reportados; el 7,93% de los casos fueron atribuidos a la exposición de agentes en el ambiente laboral: combustibles, parafina/pintura/ pulverizaciones oleosas y diésel, ambientes propios de trabajadores de almacenes de pinturas y conductores de vehículos. Los síntomas de la neumonía lipoidea exógena (NLE) descritos fueron muy variables, puede cursar asintomática o con presencia de fiebre, disnea y tos irritativa; dolor torácico, en algunos casos hemoptisis, cianosis y pérdida de peso; El examen físico generalmente es normal, aunque puede revelar sibilancias o roncus. En pruebas de función respiratoria tales como la espirometría, se presenta un patrón restrictivo, además puede hallarse un descenso en la capacidad de difusión para el monóxido de carbono. En el hemograma puede detectarse leucocitosis con predominio de neutrófilos y aumento de la velocidad de sedimentación globular, hallazgos que también pueden ser producidos por una infección concomitante. Conclusiones Se destaca el hallazgo en la literatura de los diferentes agentes causales presentes en el ambiente laboral que pueden incidir en la aparición de la enfermedad: combustibles, parafina/pintura/ pulverizaciones oleosas y diésel, ambientes propios de trabajadores de almacenes de pinturas y conductores de vehículos. Se presentó neumonía lipoidea exógena (NLE) de tipo agudo después de 30 minutos a 24 horas de exposición masiva a aceites y sustancias oleosas, luego de de ocho meses a 9,5 años de inhalación continua secundaria. Los métodos más para de la diagnóstico enfermedad incluyen el lavado broncoalveolar (BAL), la biopsia de pulmón y la con radiografía torácica. Finalmente, es posible que en pacientes con neumonía lipoidea exógena, puedan presentarse complicaciones asociadas tales como: sobreinfección, fibrosis, retracción de las lesiones, cáncer de pulmón, bronconeumonías recurrentes e hipercalcemia.
Resumo:
El presente trabajo se enfoca en el análisis de las acciones de Ecopetrol, empresa representativa del mercado de Extracción de Petróleo y Gas natural en Colombia (SP&G), durante el periodo, del 22 de mayo de 2012 al 30 de agosto de 2013. Durante este espacio de tiempo la acción sufrió una serie de variaciones en su precio las cuales se relacionaban a la nueva emisión de acciones que realizo la Compañía. Debido a este cambio en el comportamiento del activo se generaron una serie de interrogantes sobre, (i) la reacción del mercado ante diferentes sucesos ocurridos dentro de las firmas y en su entorno (ii) la capacidad de los modelos financieros de predecir y entender las posibles reacciones observadas de los activos (entendidos como deuda). Durante el desarrollo del presente trabajo se estudiará la pertinencia del mismo, en línea con los objetivos y desarrollos de la Escuela de Administración de la Universidad del Rosario. Puntualmente en temas de Perdurabilidad direccionados a la línea de Gerencia. Donde el entendimiento de la deuda como parte del funcionamiento actual y como variable determinante para el comportamiento futuro de las organizaciones tiene especial importancia. Una vez se clarifica la relación entre el presente trabajo y la Universidad, se desarrollan diferentes conceptos y teorías financieras que han permitido conocer y estudiar de manera más específica el mercado, con el objetivo de reducir los riesgos de las inversiones realizadas. Éste análisis se desarrolla en dos partes: (i) modelos de tiempo discreto y (ii) modelos de tiempo continúo. Una vez se tiene mayor claridad sobre los modelos estudiados hasta el momento se realiza el respectivo análisis de los datos mediante modelos de caos y análisis recurrente los cuales nos permiten entender que las acciones se comportan de manera caótica pero que establecen ciertas relaciones entre los precios actuales y los históricos, desarrollando comportamientos definidos entre los precios, las cantidades, el entorno macroeconómico y la organización. De otra parte, se realiza una descripción del mercado de petróleo en Colombia y se estudia a Ecopetrol como empresa y eje principal del mercado descrito en el país. La compañía Ecopetrol es representativa debido a que es uno de los mayores aportantes fiscales del país, pues sus ingresos se desprenden de bienes que se encuentran en el subsuelo por lo que la renta petrolera incluye impuestos a la producción transformación y consumo (Ecopetrol, 2003). Por último, se presentan los resultados del trabajo, así como el análisis que da lugar para presentar ciertas recomendaciones a partir de lo observado.
Resumo:
Se recoge el catálogo del museo. Se incluye la historia del ferrocarril en Cataluña, la historia del museo, los edificios e instalaciones del recinto y la descripción de las piezas. La colección en sí consta de locomotoras de vapor, eléctricas, vehículos diesel, coches de viajeros y de los elementos de infraestructura y maquinaria de vía.
Resumo:
Se recogen las actividades didácticas programadas para el 2003-04. Tanto el espacio dónde se ubica el área didáctica como las piezas de la colección se usan como un recurso educativo que pretende unir tecnología, historia y sociedad. Los grupos escolares pueden escoger una visita guiada o libre, una actividad llamada ConteTREN (CuentoTREN), que consiste en mostrar algunas piezas del museo mediante un cuento o los itinerarios secretos, que se trata de una actividad libre y autónoma para visitar el museo y aprender algunas cosas interesantes sobre el mundo del ferrocarril. Además existen las actividades en el Coche-Aula detalladas a continuación: TallerTREN-Estación de Vilanova, que se desarrolla en tres ámbitos distintos: la visita a la estación de Vilanova, un recorrido guiado por las instalaciones del museo y actividades didácticas en el coche-aula. PintaTREN, donde además de la visita libre al museo, dentro del coche-aula se explican los diferentes tipos de trenes de vapor, eléctricos y diesel a través del color. Encuentra las diferencias, que consiste en un juego donde se trabajan los diferentes tipos de energía que han usado los trenes. Pon el tren en la vía, donde se trabaja el conocimiento de la locomotora de vapor jugando a pintar, recortar y pegar. Imagina el tren del futuro, donde se acercan los trenes de alta velocidad y se hace participar a los niños en una propuesta imaginativa. Sopa de letras del tren, donde se juega con las diferentes energías ferroviarias y los elementos más importantes y característicos de los trenes. Recortable Rotonda, donde se aprende el funcionamiento del depósito de locomotoras de vapor de Vilanova i la Geltrú, que es una valiosa muestra de patrimonio industrial. Y por último, BiblioTREN: Aprender a documentarse, donde dentro de la biblioteca del museo, única en temática ferroviaria en Cataluña, los alumnos pueden ensayar la búsqueda de información para sus créditos de síntesis y hacer así prácticas de documentación.
Resumo:
El objetivo principal es la evaluación de la biomasa como recurso energético renovable en Cataluña. Su alcance requiere el estudio de diversas temáticas, desarrolladas en los doce capítulos que componen el documento.El Capítulo 1 describe los objetivos de la tesis. El Capítulo 2 describe los motivos que justifican la valorización energética del recurso biomasa. El Capítulo 3 presenta la metodología general utilizada. El Capítulo 4 realiza un análisis multicriterio del aprovechamiento energético de biomasa forestal. El Capítulo 5 cuantifica la biomasa disponible para usos energéticos en Cataluña. Los Capítulos 6, 7, 8 y 9 analizan las tecnologías y la viabilidad de la producción de energía con colza y chopo. El Capítulo 10 caracteriza físico-químicamente la biomasa de colza como combustible complementario al actual uso del grano para biodiesel. El Capítulo 11 evalua el uso de cultivos para la producción de productos químicos. El Capítulo 12 resume las Conclusiones generales.
Resumo:
Rate coefficients for reactions of nitrate radicals (NO3) with the anthropogenic emissions 2-methylpent-2-ene, (Z)-3-methylpent-2-ene.. ethyl vinyl ether, and the stress-induced plant emission ethyl vinyl ketone (pent-1-en-3-one) were determined to be (9.3 +/- 1.1) x 10(-12), (9.3 +/- 3.2) x 10(-12), (1.7 +/- 1.3) x 10(-12) and (9.4 + 2.7) x 10(-17) cm(3) molecule(-1) s(-1). We performed kinetic experiments at room temperature and atmospheric pressure using a relative-rate technique with GC-FID analysis. Experiments with ethyl vinyl ether required a modification of our established procedure that might introduce additional uncertainties, and the errors suggested reflect these difficulties. Rate coefficients are discussed in terms of electronic and steric influences. Atmospheric lifetimes with respect to important oxidants in the troposphere were calculated. NO3-initiated oxidation is found to be the strongly dominating degradation route for 2-methylpent-2-ene, (Z)-3-methylpent-2-ene and ethyl vinyl ether. Atmospheric concentrations of the alkenes and their relative contribution to the total NMHC emissions from trucks can be expected to increase if plans for the introduction of particle filters for diesel engines are implemented on a global scale. Thus more kinetic data are required to better evaluate the impact of these emissions.
Resumo:
Nanoparticles emitted from road traffic are the largest source of respiratory exposure for the general public living in urban areas. It has been suggested that the adverse health effects of airborne particles may scale with the airborne particle number, which if correct, focuses attention on the nanoparticle (less than 100 nm) size range which dominates the number count in urban areas. Urban measurements of particle size distributions have tended to show a broadly similar pattern dominated by a mode centred on 20–30 nm diameter particles emitted by diesel engine exhaust. In this paper we report the results of measurements of particle number concentration and size distribution made in a major London park as well as on the BT Tower, 160 m high. These measurements taken during the REPARTEE project (Regents Park and BT Tower experiment) show a remarkable shift in particle size distributions with major losses of the smallest particle class as particles are advected away from the traffic source. In the Park, the traffic related mode at 20–30 nm diameter is much reduced with a new mode at <10 nm. Size distribution measurements also revealed higher number concentrations of sub-50 nm particles at the BT Tower during days affected by higher turbulence as determined by Doppler Lidar measurements and indicate a loss of nanoparticles from air aged during less turbulent conditions. These results suggest that nanoparticles are lost by evaporation, rather than coagulation processes. The results have major implications for understanding the impacts of traffic-generated particulate matter on human health.
Resumo:
Black carbon aerosol plays a unique and important role in Earth’s climate system. Black carbon is a type of carbonaceous material with a unique combination of physical properties. This assessment provides an evaluation of black-carbon climate forcing that is comprehensive in its inclusion of all known and relevant processes and that is quantitative in providing best estimates and uncertainties of the main forcing terms: direct solar absorption; influence on liquid, mixed phase, and ice clouds; and deposition on snow and ice. These effects are calculated with climate models, but when possible, they are evaluated with both microphysical measurements and field observations. Predominant sources are combustion related, namely, fossil fuels for transportation, solid fuels for industrial and residential uses, and open burning of biomass. Total global emissions of black carbon using bottom-up inventory methods are 7500 Gg yr�-1 in the year 2000 with an uncertainty range of 2000 to 29000. However, global atmospheric absorption attributable to black carbon is too low in many models and should be increased by a factor of almost 3. After this scaling, the best estimate for the industrial-era (1750 to 2005) direct radiative forcing of atmospheric black carbon is +0.71 W m�-2 with 90% uncertainty bounds of (+0.08, +1.27)Wm�-2. Total direct forcing by all black carbon sources, without subtracting the preindustrial background, is estimated as +0.88 (+0.17, +1.48) W m�-2. Direct radiative forcing alone does not capture important rapid adjustment mechanisms. A framework is described and used for quantifying climate forcings, including rapid adjustments. The best estimate of industrial-era climate forcing of black carbon through all forcing mechanisms, including clouds and cryosphere forcing, is +1.1 W m�-2 with 90% uncertainty bounds of +0.17 to +2.1 W m�-2. Thus, there is a very high probability that black carbon emissions, independent of co-emitted species, have a positive forcing and warm the climate. We estimate that black carbon, with a total climate forcing of +1.1 W m�-2, is the second most important human emission in terms of its climate forcing in the present-day atmosphere; only carbon dioxide is estimated to have a greater forcing. Sources that emit black carbon also emit other short-lived species that may either cool or warm climate. Climate forcings from co-emitted species are estimated and used in the framework described herein. When the principal effects of short-lived co-emissions, including cooling agents such as sulfur dioxide, are included in net forcing, energy-related sources (fossil fuel and biofuel) have an industrial-era climate forcing of +0.22 (�-0.50 to +1.08) W m-�2 during the first year after emission. For a few of these sources, such as diesel engines and possibly residential biofuels, warming is strong enough that eliminating all short-lived emissions from these sources would reduce net climate forcing (i.e., produce cooling). When open burning emissions, which emit high levels of organic matter, are included in the total, the best estimate of net industrial-era climate forcing by all short-lived species from black-carbon-rich sources becomes slightly negative (�-0.06 W m�-2 with 90% uncertainty bounds of �-1.45 to +1.29 W m�-2). The uncertainties in net climate forcing from black-carbon-rich sources are substantial, largely due to lack of knowledge about cloud interactions with both black carbon and co-emitted organic carbon. In prioritizing potential black-carbon mitigation actions, non-science factors, such as technical feasibility, costs, policy design, and implementation feasibility play important roles. The major sources of black carbon are presently in different stages with regard to the feasibility for near-term mitigation. This assessment, by evaluating the large number and complexity of the associated physical and radiative processes in black-carbon climate forcing, sets a baseline from which to improve future climate forcing estimates.
Resumo:
Integrating renewable energy into built environments requires additional attention to the balancing of supply and demand due to their intermittent nature. Demand Side Response (DSR) has the potential to make money for organisations as well as support the System Operator as the generation mix changes. There is an opportunity to increase the use of existing technologies in order to manage demand. Company-owned standby generators are a rarely used resource; their maintenance schedule often accounts for a majority of their running hours. DSR encompasses a range of technologies and organisations; Sustainability First (2012) suggest that the System Operator (SO), energy supply companies, Distribution Network Operators (DNOs), Aggregators and Customers all stand to benefit from DSR. It is therefore important to consider impact of DSR measures to each of these stakeholders. This paper assesses the financial implications of organisations using existing standby generation equipment for DSR in order to avoid peak electricity charges. It concludes that under the current GB electricity pricing structure, there are several regions where running diesel generators at peak times is financially beneficial to organisations. Issues such as fuel costs, Carbon Reduction Commitment (CRC) charges, maintenance costs and electricity prices are discussed.
Resumo:
Nanoparticles emitted from road traffic are the largest source of respiratory exposure for the general public living in urban areas. It has been suggested that adverse health effects of airborne particles may scale with airborne particle number, which if correct, focuses attention on the nanoparticle (less than 100 nm) size range which dominates the number count in urban areas. Urban measurements of particle size distributions have tended to show a broadly similar pattern dominated by a mode centred on 20–30 nm diameter emitted by diesel engine exhaust. In this paper we report the results of measurements of particle number concentration and size distribution made in a major London park as well as on the BT Tower, 160 m aloft. These measurements taken during the REPARTEE project (Regents Park and BT Tower experiment) show a remarkable shift in particle size distributions with major losses of the smallest particle class as particles are advected away from the traffic source. In the Park, the traffic related mode at 20–30 nm diameter is much reduced with a new mode at <10 nm. Size distribution measurements also revealed higher number concentrations of sub-50 nm particles at the BT Tower during days affected by higher turbulence as determined by Doppler Lidar measurements and are indicative of loss of nanoparticles from air aged during less turbulent conditions. These results are suggestive of nanoparticle loss by evaporation, rather than coagulation processes. The results have major implications for understanding the impacts of traffic-generated particulate matter on human health.
Resumo:
Accurate monitoring of degradation levels in soils is essential in order to understand and achieve complete degradation of petroleum hydrocarbons in contaminated soils. We aimed to develop the use of multivariate methods for the monitoring of biodegradation of diesel in soils and to determine if diesel contaminated soils could be remediated to a chemical composition similar to that of an uncontaminated soil. An incubation experiment was set up with three contrasting soil types. Each soil was exposed to diesel at varying stages of degradation and then analysed for key hydrocarbons throughout 161 days of incubation. Hydrocarbon distributions were analysed by Principal Coordinate Analysis and similar samples grouped by cluster analysis. Variation and differences between samples were determined using permutational multivariate analysis of variance. It was found that all soils followed trajectories approaching the chemical composition of the unpolluted soil. Some contaminated soils were no longer significantly different to that of uncontaminated soil after 161 days of incubation. The use of cluster analysis allows the assignment of a percentage chemical similarity of a diesel contaminated soil to an uncontaminated soil sample. This will aid in the monitoring of hydrocarbon contaminated sites and the establishment of potential endpoints for successful remediation.
Resumo:
This paper presents a summary of the work done within the European Union's Seventh Framework Programme project ECLIPSE (Evaluating the Climate and Air Quality Impacts of Short-Lived Pollutants). ECLIPSE had a unique systematic concept for designing a realistic and effective mitigation scenario for short-lived climate pollutants (SLCPs; methane, aerosols and ozone, and their precursor species) and quantifying its climate and air quality impacts, and this paper presents the results in the context of this overarching strategy. The first step in ECLIPSE was to create a new emission inventory based on current legislation (CLE) for the recent past and until 2050. Substantial progress compared to previous work was made by including previously unaccounted types of sources such as flaring of gas associated with oil production, and wick lamps. These emission data were used for present-day reference simulations with four advanced Earth system models (ESMs) and six chemistry transport models (CTMs). The model simulations were compared with a variety of ground-based and satellite observational data sets from Asia, Europe and the Arctic. It was found that the models still underestimate the measured seasonality of aerosols in the Arctic but to a lesser extent than in previous studies. Problems likely related to the emissions were identified for northern Russia and India, in particular. To estimate the climate impacts of SLCPs, ECLIPSE followed two paths of research: the first path calculated radiative forcing (RF) values for a large matrix of SLCP species emissions, for different seasons and regions independently. Based on these RF calculations, the Global Temperature change Potential metric for a time horizon of 20 years (GTP20) was calculated for each SLCP emission type. This climate metric was then used in an integrated assessment model to identify all emission mitigation measures with a beneficial air quality and short-term (20-year) climate impact. These measures together defined a SLCP mitigation (MIT) scenario. Compared to CLE, the MIT scenario would reduce global methane (CH4) and black carbon (BC) emissions by about 50 and 80 %, respectively. For CH4, measures on shale gas production, waste management and coal mines were most important. For non-CH4 SLCPs, elimination of high-emitting vehicles and wick lamps, as well as reducing emissions from gas flaring, coal and biomass stoves, agricultural waste, solvents and diesel engines were most important. These measures lead to large reductions in calculated surface concentrations of ozone and particulate matter. We estimate that in the EU, the loss of statistical life expectancy due to air pollution was 7.5 months in 2010, which will be reduced to 5.2 months by 2030 in the CLE scenario. The MIT scenario would reduce this value by another 0.9 to 4.3 months. Substantially larger reductions due to the mitigation are found for China (1.8 months) and India (11–12 months). The climate metrics cannot fully quantify the climate response. Therefore, a second research path was taken. Transient climate ensemble simulations with the four ESMs were run for the CLE and MIT scenarios, to determine the climate impacts of the mitigation. In these simulations, the CLE scenario resulted in a surface temperature increase of 0.70 ± 0.14 K between the years 2006 and 2050. For the decade 2041–2050, the warming was reduced by 0.22 ± 0.07 K in the MIT scenario, and this result was in almost exact agreement with the response calculated based on the emission metrics (reduced warming of 0.22 ± 0.09 K). The metrics calculations suggest that non-CH4 SLCPs contribute ~ 22 % to this response and CH4 78 %. This could not be fully confirmed by the transient simulations, which attributed about 90 % of the temperature response to CH4 reductions. Attribution of the observed temperature response to non-CH4 SLCP emission reductions and BC specifically is hampered in the transient simulations by small forcing and co-emitted species of the emission basket chosen. Nevertheless, an important conclusion is that our mitigation basket as a whole would lead to clear benefits for both air quality and climate. The climate response from BC reductions in our study is smaller than reported previously, possibly because our study is one of the first to use fully coupled climate models, where unforced variability and sea ice responses cause relatively strong temperature fluctuations that may counteract (and, thus, mask) the impacts of small emission reductions. The temperature responses to the mitigation were generally stronger over the continents than over the oceans, and with a warming reduction of 0.44 K (0.39–0.49) K the largest over the Arctic. Our calculations suggest particularly beneficial climate responses in southern Europe, where surface warming was reduced by about 0.3 K and precipitation rates were increased by about 15 (6–21) mm yr−1 (more than 4 % of total precipitation) from spring to autumn. Thus, the mitigation could help to alleviate expected future drought and water shortages in the Mediterranean area. We also report other important results of the ECLIPSE project.