Assessing boost-assist options for turbocharged engines using 1-D engine simulation and model predictive control

Delivering acceptable low end torque and good transient response is a significant challenge for all turbocharged engines. As downsized gasoline engines and Diesel engines make up a larger and larger proportion of the light-duty engines entering the market, the issue takes on greater significance. Several schemes have been proposed to improve torque response in highly boosted engines, including the use of electrical assist turbochargers and compressed air assist. In this paper we examine these methods with respect to their effectiveness in improving transient response and their relative performance along with some of the practical considerations for real world application. Results shown in this paper are from 1-D simulations using the Ricardo WAVE software package. The simulation model is based on a production light-duty Diesel engine modified to allow the introduction of compressed air at various points in the air-path as well as direct torque application to the turbocharger shaft (such as might be available from an electrical assist turbocharger). Whilst the 1-D simulation software provides a suitable environment for investigating the various boost assistance options, the overall air path performance also depends upon the control system. The introduction of boost assistance complicates the control in two significant ways: the system may run into constraints (such as compressor surge) that are not encountered in normal operation and the assistance introduces an additional control input. Production engine controllers are usually based on gain-scheduled PID control and extensive calibration. For this study, the non-linear nature of the engine together with the multiple configurations considered and the slower than real-time execution of 1-D models makes such an approach time consuming. Moreover, an ad-hoc approach would leave some doubt as to the fairness of comparisons between the different boost-assist options. Model Predictive Control has been shown to offer a convenient approach to controlling the 1-D simulations in a close to optimal manner for a typical Diesel VGT-EGR air path configuration. We show that the same technique can be applied to all the considered assistance methods with only modest calibration effort required. Copyright © 2012 SAE International.

A novel modeling approach for design studies of brushless doubly fed induction generator based on magnetic equivalent circuit

Brushless doubly fed induction generator (BDFIG) has substantial benefits, which make it an attractive alternative as a wind turbine generator. However, it suffers from lower efficiency and larger dimensions in comparison to DFIG. Hence, optimizing the BDFIG structure is necessary for enhancing its situation commercially. In previous studies, a simple model has been used in BDFIG design procedure that is insufficiently accurate. Furthermore, magnetic saturation and iron loss are not considered because of difficulties in determination of flux density distributions. The aim of this paper is to establish an accurate yet computationally fast model suitable for BDFIG design studies. The proposed approach combines three equivalent circuits including electric, magnetic and thermal models. Utilizing electric equivalent circuit makes it possible to apply static form of magnetic equivalent circuit, because the elapsed time to reach steady-state results in the dynamic form is too long for using in population-based design studies. The operating characteristics, which are necessary for evaluating the objective function and constraints values of the optimization problem, can be calculated using the presented approach considering iron loss, saturation, and geometrical details. The simulation results of a D-180 prototype BDFIG are compared with measured data in order to validate the developed model. © 1986-2012 IEEE.

Responses of dark respiration in the light to desiccation and temperature in the intertidal macroalga, Ulva lactuca (Chorophyta) during emersion

Dark respiration (nonphotorespiratory mitochondrial CO2 release) in the light (R-L) of the intertidal macroalga Ulva lactuca (Chorophyta) during emersion was investigated with respect to its response to variations in temperature and desiccation. R-L was estimated by CO2 gas-exchange analysis using the Kok effect method, whereas dark respiration in darkness (R-D) was determined from CO2 release at zero light. Rates of R, were significantly and consistently lower than those of R-D in emersed U. lactuca across all the temperature and desiccation levels measured. This demonstrated that dark respiration was partially depressed in the light, with the percentage inhibition ranging from 32 to 62%. Desiccation exerted a negative effect on R-L and R-D at a high temperature, 33 degrees C, whereas it had much less effect on respiration at low and moderate temperatures, 23 and 28 degrees C. In general, R-L and R-D increased with increasing temperature in U. lactuca during all stages of emersion but responded less positively to temperature change with increasing desiccation. Additionally, the Q(10) value (i.e. the proportional increase of respiration for each 10 degrees C rise in temperature) for R-L calculated over the temperature range of 23 to 33 degrees C was significantly higher than that for R-D in U. lactuca during the initial stages of emersion. Respiratory carbon loss as a percentage of gross photosynthetic carbon gain increased with increasing temperature and/or desiccation but was significantly reduced when estimated using R-L rather than R-D. It is suggested that measurements of R-L and how it changes in a variable environment are as important as estimates of R-D and photosynthesis in determining simultaneous balance between photosynthetic carbon uptake and respiratory carbon loss and in modeling the net daily carbon gain for an intertidal macroalga.

Reproductive effects of prenatal exposure to nonylphenol on zebrafish (Danio rerio)

Mature female and male zebrafish were separated and exposed to nonylphenol (NP) at 0.1, 1, 10, 50, 100 and 500 mu g/L, respectively, for 3 weeks. Gonadosomatic index (GSI) in both sexes and vitellogenin (VTG) induction in males was measured as the bioindicators for the impairment to the parents. The results indicated that 50 mu g/L of NP was the non-observed effect concentration (NOEC) for GSI and VTG induction. Afterwards, the 50 mu g/L NP exposed females and males, and the control females and males were cross-wise pair-bred in the control water for one week to examine the reproductive effects. The embryonic cathepsin D (CAT D) activity, eggshell thickness, fecundity, hatching rate and malformation (vertebral column flexure) rate of offspring were determined in the four pair-bred groups. While endpoints remained unchanged in the groups with exposed males, prenatal exposure of females to 50 mu g/L of NP resulted in the impairment of reproduction in groups with exposed females including inhibition of CAT D activity (P < 0.05), decrease of eggshell thickness (by 23.6%) and elevation of malformation rate (P < 0.001). These results suggested NP could induce reproductive damage to zebrafish at NOEC for parents. The results also imply that alterations of CAT D activity and eggshell thickness may be more sensitive biomarkers to indicate the reproductive effects caused by endocrine disrupting chemicals. (c) 2005 Elsevier Inc. All rights is reserved.

Attenuation of photosynthetically available radiation by chlorophyll, chromophoric dissolved organic matter, and tripton in lake Donghu, China

The attenuation coefficient of photosynthetically available radiation [K-d(PAR)] and three water quality parameters [chlorophyll a (chl a)], chromophoric dissolved organic matter (CDOM) and tripton] were measured at three stations in shallow, subtropical Lake Donghu from April 2003 to March 2004. The multiple regression equation of K-d(PAR) versus chl a, CDOM, and tripton was: K-d(PAR) = 0.44 + 0.019 chl a + 1.88 CDOM + 0.016 tripton, which revealed the relative contributions of the three parameters to K-d(PAR). The effects of water and CDOM on K-d(PAR) were of minor importance (19-26%), while chl a and tripton were the two greatest contributors, accounting collectively for 74-81%.

Doping dependence of the Raman spectrum of defected graphene.

We investigate the evolution of the Raman spectrum of defected graphene as a function of doping. Polymer electrolyte gating allows us to move the Fermi level up to 0.7 eV, as directly monitored by in situ Hall-effect measurements. For a given number of defects, we find that the intensities of the D and D' peaks decrease with increasing doping. We assign this to an increased total scattering rate of the photoexcited electrons and holes, due to the doping-dependent strength of electron-electron scattering. We present a general relation between D peak intensity and defects valid for any doping level.

Genetic heterogeneity and ploidy level analysis among different gynogenetic clones of the polyploid gibel carp

Background: Some triploid and tetraploid clones have been identified in the gynogenetic gibel carp, Carassius auratus gibelio Bloch, by karyotypic and cytologic analyses over many years. Further, 5-20% males and karyotypic diversity have been found among their natural and artificial populations. However, the DNA contents and the relation to their ploidy level and chromosome numbers have not been ascertained, and whether normal meiosis occurs in spermatogenesis needs to be determined in the different clones. Methods: The sampled blood cells or sperms were mixed with blood cells from chicken or individual gibel carp and fixed in 70% pre-cooled ethanol overnight at 4degreesC. The mixed cell pellets were washed 2-3 times in 1x phosphate buffered saline and then resuspended in the solution containing 0.5% pepsin and 0.1 M HCl. DNA was stained with propidium iodide solution (40 mug/mL) containing 4 kU/ml RNase. The measurements of DNA contents were performed with Phoenix Flow Systems. Results: Triploid clones A, E, F, and P had almost equal DNA content, but triploid clone D had greater DNA content than did the other four triploid clones. DNA content of clone M (7.01 +/- 0.15 pg/nucleus) was almost equal to the DNA content of clone D (5-38 +/- 0.06 pg/nucleus) plus the DNA content of common carp sperm (1.64 +/- 0.02 pg/nucleus). The DNA contents of sperms from clones A, P, and D were half of their blood cells, suggesting that normal meiosis occurs in spermatogenesis. Conclusions: Flow cytometry is a powerful method to analyze genetic heterogeneity and ploidy level among different gynogenetic clones of polyploid gibel carp. Through this study, four questions have been answered. (a) The DNA content correlation among the five triploid clones and one multiple tetraploid clone was revealed in the gibel carp, and the contents increased with not only the ploidy level but also the chromosome number. (b) Mean DNA content was 0.052 pg in six extra chromosomes of clone D, which was higher than that of each chromosome in clones A, E, F, and P (about 0.032 pg/ chromosome). This means that the six extra chromosomes are larger chromosomes. (c) Normal meiosis occurred during spermatogenesis of the gibel carp, because DNA contents of the sperms from clones A, P, and D were almost half of that in their blood cells. (d) Multiple tetraploid clone M (7.01 +/- 0.15 pg/nucleus) contained the complete genome of clone D (5.38 +/- 0.06 pg/nucleus) and the genome of common carp sperm (1.64 +/- 0.02 pg/nucleus). Cytometry Part A 56A:46-52, 2003. (C) 2003 Wiley-Liss, Inc.

Molecular analysis of silver crucian carp (Carassius auratus gibelio Bloch) clones by SCAR markers

Random amplified polymorphic DNA (RAPD) molecular markers specific for one, two or three clones have been identified from five gynogenetic clones of silver crucian carp (Carassius auratus gibelio Bloch) using RAPD markers developed earlier. In this study, three RAPD markers (RA1-PA, RA2-EF and RA4-D) produced by Opj-1, and two RAPD DNA fragments (RA3-PAD and RA5-D) produced by Opj-7, were selected for molecular cloning and sequencing. Sequence data indicated that there were identical 801-bp nucleotide sequences in the shared marker RA1-PA cloned respectively from clones P and A, and the shared marker RA2-EF (which was cloned from clones E and F), were also of identical 958-by nucleotide sequences. The nucleotide sequences of the shared marker RA3-PAD fragments were also similar for 1181 by among clones P, A and D. The specific fragment RA4-D was composed of 628 bp, and the fragment RA5-D from clone D contained 385 nucleotides. According to the nucleotide sequences, we designed and synthesized five pairs of sequence characterized amplified regions (SCAR) primers to identify the specific fragments in these gynogenetic clones of silver crucian carp. Only individuals from clones P and A amplified a specific band using a pair of SCI-PA primers synthesized according to the marker RA1-PA sequences, whereas no products were detected in individuals from clones D, E and F. The PCR products amplified using SC2-EF and SC3-PAD primers were as expected. Furthermore, the pair of SC4-D primers amplified specific bands only in individuals from clone D, although weak bands could be produced in all individuals of the five clones when lower annealing temperatures were used. However, an additional pair of SC5-D primers designed from the RA5-D marker sequences could amplify a DNA band in individuals from clones P, A and D, and the same weak band was produced in clone E, whereas no products were detected in individuals from clone F. Searches in GenBank revealed that the 385-bp DNA fragment from RA5-D was homologous to the 5' end of gonadotropin I beta subunit 2 gene and growth hormone gene. No homologous sequences were found for other markers in GenBank. The SCAR markers identified in this study will offer a powerful, easy, and rapid method for discrimination of different clones and for genetic analyses that examine their origins and unique reproductive modes in crucian carp. Furthermore, they will likely benefit future selective breeding programs as reliable and reproducible molecular markers. (C) 2001 Elsevier Science B.V. All rights reserved.

Theoretical design and performance of InxGa1-xN two-junction solar cells

The efficiencies of InxGa1-xN two-junction solar cells are calculated with various bandgap combinations of subcells under AM1.5 global, AM1.5 direct and AM0 spectra. The influence of top-cell thickness on efficiency has been studied and the performance of InxGa1-xN cells for the maximum light concentration of various spectra has been evaluated. Under one-sun irradiance, the optimum efficiency is 35.1% for the AM1.5 global spectrum, with a bandgap combination of top/bottom cells as 1.74 eV/1.15 eV. And the limiting efficiency is 40.9% for the highest light concentration of the AM1.5 global spectrum, with the top/bottom cell bandgap as 1.72 eV/1.12 eV.

Effects of the morphology of ZnO/Ag interface on the surface-plasmon-enhanced emission of ZnO films

The effects of the surface morphology of Ag on the surface-plasmon-enhanced emission of ZnO films have been studied for a ZnO/Ag/Si system by photoluminescence spectroscopy and atomic force microscopy. The results indicate that the enhancement of ZnO ultraviolet emission is dependent on the deposition conditions of the Ag interlayers. By examining the dependence of the enhancement ratio of surface-plasmon-mediated emission on the characteristic parameters of Ag surface morphology, we found that the surface plasmon coupling to light is determined by both the Ag particle size and density.

Characterization of ZnMgO hexagonal-nanotowers/films on m-plane sapphire synthesized by metal organic chemical vapour deposition

ZnMgO hexagonal-nanotowers/films grown on m-plane sapphire substrates were successfully synthesized using a vertical low-pressure metal organic chemical vapour deposition system. The structural and optical properties of the as-obtained products were characterized using various techniques. They were grown along the non-polar [1 0 (1) over bar 0] direction and possessed wurtzite structure. The ZnMgO hexagonal-nanotowers were about 200 nm in diameter at the bottom and 120 nm in length. Photoluminescence and Raman spectra show that the products have good crystal quality with few oxygen vacancies. With Mg incorporation, multiple-phonon scattering becomes weak and broad, and the intensities of all observed vibrational modes decrease. The ultraviolet near band edge emission shows a clear blueshift (as much as 100 meV) and broadening compared with that of pure ZnO products.

Structure and magnetic characteristics of nonpolar a-plane GaN : Mn films

Diluted magnetic nonpolar GaN:Mn films have been fabricated by implanting Mn ions into unintentionally doped nonpolar a-plane (1 1 (2) over bar 0) GaN films with a subsequent rapid thermal annealing (RTA) process. The structure, morphology and magnetic characteristics of the samples were investigated by means of high-resolution x-ray diffraction (XRD), atomic force microscopy (AFM) and a superconducting quantum interference device (SQUID), respectively. The XRD analysis shows that the RTA process can effectively recover the crystal deterioration caused by the implantation process and that there is no obvious change in the lattice parameter for the as-annealed sample. The SQUID result indicates that the as-annealed sample shows ferromagnetic properties and magnetic anisotropy at room temperature.

Photoelectric characteristics of metal/InGaN/GaN heterojunction structure

A heterojunction structure photodetector was fabricated by evaporating a semitransparent Ni/Au metal film oil the InGaN/GaN structure. The photocurrent (PC) spectra show that both the Schottky junction (NiAu/InGaN) and the InGaN/GaN isotype heterojunction contribute to the PC signal which suggests that two junctions are connected in series and result in a broader spectral response of the device. Secondary electron, cathodoluminescence and electron-beam-induced current images measured from the same area of the edge surface clearly reveal the profile of the layer structure and distribution of the built-in electric field around the two junctions. A band diagram of the device is drawn based oil the consideration of the polarization effect at the InGaN/GaN interface. The analysis is consistent with the physical mechanism of a tandem structure of two junctions connected in series.

Spectroscopy of long wavelength coupled quantum dots

We obtained a low density of coupled InAs/GaAs quantum dots (QDs) with an emission wavelength of around 1.3 mu m at room temperature. Atomic force microscopy and transmission electronic microscopy reveal that the dot size difference and the lateral displacement between the two dots are related to the spacer thickness. Spectroscopy of the coupled QD ensembles is considerably influenced by the spacer thickness.

Investigation on the structural origin of n-type conductivity in InN films

This work presents a study of the correlation between the electrical properties and the structural defects in nominally undoped InN films. It is found that the density of edge-type threading dislocations (TDs) considerably affects the electron concentration and mobility in InN films. The Hall-effect measured electron concentration increases, while the Hall mobility decreases with the increase in the edge-type TD density. With the combination of secondary ion mass spectrometry and positron annihilation analysis, we suggest that donor-type point defects at the edge-type TD lines may serve as dominant donors in InN films and affect the carrier mobility.