Entwicklung, Aufbau und Messungen eines schnellen Eiskeimzählers

Im Rahmen dieser Arbeit wurde ein neuer Eiskeimzähler FINCH (Fast Ice Nucleus CHamber) entwickelt und erste Messungen von verschiedenen Testaerosolen im Labor und atmosphärischem Aerosol durchgeführt. Die Aerosolpartikel bzw. Ice Nuclei IN werden bei Temperaturen unter dem Gefrierpunkt und Übersättigungen in Bezug auf Eis zum Anwachsen zu Eiskristallen gebracht, um sie mittels optischer Detektion zu erfassen. In FINCH ist dies durch das Prinzip der Mischung realisiert, wodurch eine kontinuierliche Messung der IN-Anzahlkonzentration gewährleistet ist. Hierbei kann mit sehr hohen Sammelflussraten von bis zu 10 l/min gemessen werden. Ebenso ist ein schnelles Abfahren von verschiedenen Sättigungsverhältnissen in Bezug auf Eis in einem weiten Bereich von 0.9 - 1.7 bei konstanten Temperaturen bis zu −23 °C möglich. Die Detektion der Eiskristalle und damit der Bestimmung der IN-Anzahlkonzentration erfolgt über einen neu entwickelten optischen Sensor basierend auf der unterschiedlichen Depolarisation des zurückgestreuten Lichtes von Eiskristallen und unterkühlten Tropfen. In Labermessungen wurden Aktivierungstemperatur und -sättigungsverhältnis von Silberjodid AgI und Kaolinit vermessen. Die Resultate zeigten gute Übereinstimmungen mit Ergebnissen aus der Literatur sowie Parallelmessungen mit FRIDGE (FRankfurt Ice Deposition freezinG Experiment). FRIDGE ist eine statische Diffusionskammer zur Aktivierung und Auszählung von Eiskeimen, die auf einem Filter gesammelt wurden. Bei atmosphärischen Messungen auf dem Jungfraujoch(Schweiz) lagen die IN-Anzahlkonzentrationen mit bis zu 4 l−1 im Rahmen der aus der Literatur bekannten Werte. Messungen der Eiskristallresiduen von Mischwolken zeigten hingegen, dass nur jedes tausendste als Eiskeim im Depositionsmode aktiv ist. Hier scheinen andere Gefrierprozesse und sekundäre Eiskristallbildung von sehr großer Bedeutung für die Anzahlkonzentration der Eiskristallresiduen zu sein. Eine weitere Messung von atmosphärischem Aerosol in Frankfurt zeigte IN-Anzahlkonzentrationen bis zu 30 l−1 bei Aktivierungstemperaturen um −14 °C. Die parallele Probenahme auf Siliziumplättchen für die Messungen der IN-Anzahlkonzentration in FRIDGE ergaben Werte im gleichen Anzahlkonzentrationsbereich.

3D nanostructured microcarriers for cell therapy in regenerative medicine

Supercritical Emulsion Extraction technology (SEE-C) was proposed for the production of poly-lactic-co-glycolic acid microcarriers. SEE-C operating parameters as pressure, temperature and flow rate ratios were analyzed and the process performance was optimized in terms of size distribution and encapsulation efficiency. Microdevices loaded with bovine serum insulin were produced with different sizes (2 and 3 µm) or insulin charges (3 and 6 mg/g) and with an encapsulation efficiency of 60%. The microcarriers were characterized in terms of insulin release profile in two different media (PBS and DMEM) and the diffusion and degradation constants were also estimated by using a mathematical model. PLGA microdevices were also used in a cultivation of embryonic ventricular myoblasts (cell line H9c2 obtained from rat) in a FBS serum free medium to monitor cell viability and growth in dependence of insulin released. Good cell viability and growth were observed on 3 µm microdevices loaded with 3 mg/g of insulin. PLGA microspheres loaded with growth factors (GFs) were charged into alginate scaffold with human Mesenchimal Steam Cells (hMSC) for bone tissue engineering with the aim of monitoring the effect of the local release of these signals on cells differentiation. These “living” 3D scaffolds were incubated in a direct perfusion tubular bioreactor to enhance nutrient transport and exposing the cells to a given shear stress. Different GFs such as, h-VEGF, h-BMP2 and a mix of two (ratio 1:1) were loaded and alginate beads were recovered from dynamic (tubular perfusion system bioreactor) and static culture at different time points (1st, 7th, 21st days) for the analytical assays such as, live/dead; alkaline phosphatase; osteocalcin; osteopontin and Van Kossa Immunoassay. The immunoassay confirmed always a better cells differentiation in the bioreactor with respect to the static culture and revealed a great influence of the BMP-2 released in the scaffold on cell differentiation.

Regolazione della pompa elettrica del carburante a bassa pressione: Analisi dell'impatto sul consumo specifico di un motore a combustione interna

The trend of CO2 emission limit and fuel saving due to the oil price increase and are important drivers for engines development. The engine auxiliary devices electrification (g.e fuel pump) is a way to reduce the energy consumption, because it becomes possible to control them depending on engine operation point, this kid of management can be applied to the electric low-pressure pump. Usually the fuel delivery is performed at the maximum flow rate and a pressure regulator discharges the exceeding fuel amount inside the rail (gasoline engine) or upstream of the high pressure pump (common rail diesel engine). In this work it has been investigated the fuel saving achievable through a proper control of the electric fuel pump on a small common rail diesel engine, and a control architecture is proposed. The aim was to maximize the fuel economy without any impact on pressure control in the engine transient conditions. L'andamento del limite di emissioni di CO2 e il risparmio di carburante dovuto all'aumento del prezzo del petrolio sono fattori importanti per lo sviluppo dei motori. I dispositivi ausiliari, come la pompa del carburante, sono un modo per ridurre il consumo energetico, in quanto diventa possibile controllarli a seconda del punto di funzionamento del motore, questo tipo di gestione può essere applicato alla pompa elettrica a bassa pressione. Solitamente la portata del combustibile viene eseguita alla portata massima e un regolatore di pressione si scarica la quantità eccedente di carburante all'interno del rail (motore a benzina) o a monte della pompa a alta pressione (common rail motore diesel). In questo lavoro è stato studiato il risparmio di combustibile ottenibile attraverso un adeguato controllo della pompa elettrica del carburante su un piccolo motore diesel common rail e viene proposta una architettura di controllo. Lo scopo è quello di massimizzare il risparmio di carburante, senza alcun impatto sul controllo della pressione nelle condizioni transitorie del motore.

Analisi di fattibilità di un sensore di portata ad ultrasuoni

Analisi di possibile utilizzo di sensori ad ultrasuoni per il calcolo della portata massica. Tramite ricerche bibliografiche si è potuto osservare come sia stato possibile applicare tale strumento anche per il calcolo della velocità del vento in stazioni meteorologiche come anche per il calcolo della portata in condotti in cui scorrono liquidi o gas. Lo studio è stato realizzato in quanto la misura di portata interessa molti campi da quello aeronautico/automobilistico a quello industriale; un'applicazione aerospaziale, per esempio, può essere quella di calcolare la portata in ingresso ad una motorizzazione necessaria per quantificare le dosi di combustibile da iniettare in camera di combustione.

Efficacia e complicanze durante la curva di apprendimento della Thulep: risultati a breve e medio termine delle prime 48 procedure

MATERIALI E METODI: Tra il 2012 e il 2013, abbiamo analizzato in uno studio prospettico i dati di 48 pazienti sottoposti a ThuLEP con approccio autodidatta. I pazienti sono stati rivalutati a 3, 6, 12 e 24 mesi con la valutazione del PSA, il residuo post-minzionale (RPM), l'uroflussometria (Qmax), l'ecografia transrettale e questionari validati (IPSS: international prostate symptom score e QoL: quality of life) RISULTATI: Il volume medio della prostata è di 63 ± 5,3 ml. Il tempo operatorio medio è stato di 127,58 ± 28.50 minuti. Il peso medio del tessuto asportato è stato di 30,40 ± 13,90 gr. A 6 mesi dopo l'intervento l'RPM medio è diminuito da 165,13 ± 80,15 ml a 7,78 ± 29.19 ml, mentre il Qmax medio è aumentato da 5.75 ± 1.67ml / s a 18.1 ± 5.27 ml / s. I valori medi dei IPSS e QoL hanno dimostrato un progressivo miglioramento: da 19.15 (IQR: 2-31) e 4 (IQR: 1-6) nel preoperatorio a 6.04 (IQR: 1-20) e 1.13 (IQR: 1-4), rispettivamente. Durante la curva di apprendimento si è assistito ad un progressivo aumento del peso del tessuto enucleato e ad una progressiva riduzione del tempo di ospedalizzazione e di cateterismo. Tra le principali complicanze ricordiamo un tasso di incontinenza transitoria del 12,5% a 3 mesi e del 2.1% a 12 mesi. CONCLUSIONI: ThuLEP rappresenta una tecnica chirurgica efficace, sicura e riproducibile indipendentemente dalle dimensioni della prostata. I nostri dati suggeriscono che la ThuLEP offre un miglioramento significativo dei parametri funzionali comparabili con le tecniche tradizionali, nonostante una lunga curva di apprendimento.

Entwicklung und Charakterisierung eines Drop-on-Demand-Aerosolgenerators für die Probenzuführung kleinster Flüssigkeitsmengen in der analytischen Atomspektroskopie

Die pneumatische Zerstäubung ist die häufigste Methode der Probenzuführung von Flüssigkeiten in der Plasmaspektrometrie. Trotz der bekannten Limitierungen dieser Systeme, wie die hohen Probenverluste, finden diese Zerstäuber aufgrund ihrer guten Robustheit eine breite Anwendung. Die flussratenabhängige Aerosolcharakteristik und pumpenbasierte Signalschwankungen limitieren bisher Weiterentwicklungen. Diese Probleme werden umso gravierender, je weiter die notwendige Miniaturisierung dieser Systeme fortschreitet. Der neuartige Ansatz dieser Arbeit basiert auf dem Einsatz modifizierter Inkjet-Druckerpatronen für die Dosierung von pL-Tropfen. Ein selbst entwickelter Mikrokontroller ermöglicht den Betrieb von matrixkodierten Patronen des Typs HP45 mit vollem Zugriff auf alle essentiellen Betriebsparameter. Durch die neuartige Aerosoltransportkammer gelang die effiziente Kopplung des Tropfenerzeugungssystems an ein ICP-MS. Das so aufgebaute drop-on-demand-System (DOD) zeigt im Vergleich zu herkömmlichen und miniaturisierten Zerstäubern eine deutlich gesteigerte Empfindlichkeit (8 - 18x, elementabhängig) bei leicht erhöhtem, aber im Grunde vergleichbarem Signalrauschen. Darüber hinaus ist die Flexibilität durch die große Zahl an Freiheitsgraden des Systems überragend. So ist die Flussrate über einen großen Bereich variabel (5 nL - 12,5 µL min-1), ohne dabei die primäre Aerosolcharakteristik zu beeinflussen, welche vom Nutzer durch Wahl der elektrischen Parameter bestimmt wird. Das entwickelte Probenzuführungssystem ist verglichen mit dem pneumatischen Referenzsystem weniger anfällig gegenüber Matrixeffekten beim Einsatz von realen Proben mit hohen Anteilen gelöster Substanzen. So gelingt die richtige Quantifizierung von fünf Metallen im Spurenkonzentrationsbereich (Li, Sr, Mo, Sb und Cs) in nur 12 µL Urin-Referenzmaterial mittels externer Kalibrierung ohne Matrixanpassung. Wohingegen beim pneumatischen Referenzsystem die aufwändigere Standardadditionsmethode sowie über 250 µL Probenvolumen für eine akkurate Bestimmung der Analyten nötig sind. Darüber hinaus wird basierend auf der Dosierfrequenz eines dualen DOD-Systems eine neuartige Kalibrierstrategie vorgestellt. Bei diesem Ansatz werden nur eine Standard- und eine Blindlösung anstelle einer Reihe unterschiedlich konzentrierter Standards benötigt, um eine lineare Kalibrierfunktion zu erzeugen. Zusätzlich wurde mittels selbst entwickelter, zeitlich aufgelöster ICP-MS umfangreiche Rauschspektren aufgenommen. Aus diesen gelang die Ermittlung der Ursache des erhöhten Signalrauschens des DOD, welches maßgeblich durch das zeitlich nicht äquidistante Eintreffen der Tropfen am Detektor verursacht wird. Diese Messtechnik erlaubt auch die Detektion einzeln zugeführter Tropfen, wodurch ein Vergleich der Volumenverteilung der mittels ICP-MS detektierten, gegenüber den generierten und auf optischem Wege charakterisierten Tropfen möglich wurde. Dieses Werkzeug ist für diagnostische Untersuchungen äußerst hilfreich. So konnte aus diesen Studien neben der Aufklärung von Aerosoltransportprozessen die Transporteffizienz des DOD ermittelt werden, welche bis zu 94 Vol.-% beträgt.

Dental erosion--an overview with emphasis on chemical and histopathological aspects

The quality of dental care and modern achievements in dental science depend strongly on understanding the properties of teeth and the basic principles and mechanisms involved in their interaction with surrounding media. Erosion is a disorder to which such properties as structural features of tooth, physiological properties of saliva, and extrinsic and intrinsic acidic sources and habits contribute, and all must be carefully considered. The degree of saturation in the surrounding solution, which is determined by pH and calcium and phosphate concentrations, is the driving force for dissolution of dental hard tissue. In relation to caries, with the calcium and phosphate concentrations in plaque fluid, the 'critical pH' below which enamel dissolves is about 5.5. For erosion, the critical pH is lower in products (e.g. yoghurt) containing more calcium and phosphate than plaque fluid and higher when the concentrations are lower. Dental erosion starts by initial softening of the enamel surface followed by loss of volume with a softened layer persisting at the surface of the remaining tissue. Dentine erosion is not clearly understood, so further in vivo studies, including histopathological aspects, are needed. Clinical reports show that exposure to acids combined with an insufficient salivary flow rate results in enhanced dissolution. The effects of these and other interactions result in a permanent ion/substance exchange and reorganisation within the tooth material or at its interface, thus altering its strength and structure. The rate and severity of erosion are determined by the susceptibility of the dental tissues towards dissolution. Because enamel contains less soluble mineral than dentine, it tends to erode more slowly. The chemical mechanisms of erosion are also summarised in this review. Special attention is given to the microscopic and macroscopic histopathology of erosion.

Effect of pulsatility on the mathematical modeling of rotary blood pumps

In this study, the effect of time derivatives of flow rate and rotational speed was investigated on the mathematical modeling of a rotary blood pump (RBP). The basic model estimates the pressure head of the pump as a dependent variable using measured flow and speed as predictive variables. Performance of the model was evaluated by adding time derivative terms for flow and speed. First, to create a realistic working condition, the Levitronix CentriMag RBP was implanted in a sheep. All parameters from the model were physically measured and digitally acquired over a wide range of conditions, including pulsatile speed. Second, a statistical analysis of the different variables (flow, speed, and their time derivatives) based on multiple regression analysis was performed to determine the significant variables for pressure head estimation. Finally, different mathematical models were used to show the effect of time derivative terms on the performance of the models. In order to evaluate how well the estimated pressure head using different models fits the measured pressure head, root mean square error and correlation coefficient were used. The results indicate that inclusion of time derivatives of flow and speed can improve model accuracy, but only minimally.

Morphological and functional 3-Tesla magnetic resonance imaging of saphenous vein coronary artery bypass grafts

Evaluation of a novel non-invasive tool for postoperative follow-up of patients postelective saphenous vein coronary artery bypass graft (CABG) was performed. Ten patients were included. Their bypass grafts supplied the right coronary artery (7), marginal branches (1), diagonal branches (2), and the circumflex artery (n=1). Each bypass was examined intraoperatively using Doppler flow measurement. Patients were examined with a 3-Tesla magnetic resonance imaging (MRI) scanner (MAGNETOM Verio, Siemens, Erlangen, Germany) within one week postsurgery using MR-angiography with an intravasal contrast agent and velocity encoded phase-contrast flow measurements. Intraoperative Doppler flow measurements revealed regular flow patterns in all vascular territories supplied. The median intraoperative flow rate was 50 ml/min with an inter-quartile range (IQR) of 42-70 ml/min. The clinical postoperative course was uneventful. MRI showed all grafts to be patent. The median postoperative flow rate was 50 ml/min (IQR: 32-65 ml/min). MRI flow rates agreed well with intraoperative Doppler flow measurements (mean difference: -2.8±20.1 ml/min). This initial study demonstrates that 3-Tesla MRI flow measurements correlated well with Doppler thus reconfirming the graft patency postCABG. Further refinement and broader application of this technique may facilitate follow-up postCABG potentially replacing empiric clinical judgment by reliable non-invasive imaging.

DESIGN OF A LIQUID FUEL INJECTOR FOR ALTERNATIVE FUEL STUDIES IN AN ATMOSPHERIC MODEL GAS TURBINE COMBUSTOR

A new liquid-fuel injector was designed for use in the atmospheric-pressure, model gas turbine combustor in Bucknell University’s Combustion Research Laboratory during alternative fuel testing. The current liquid-fuel injector requires a higher-than-desired pressure drop and volumetric flow rate to provide proper atomization of liquid fuels. An air-blast atomizer type of fuel injector was chosen and an experiment utilizing water as the working fluid was performed on a variable-geometry prototype. Visualization of the spray pattern was achieved through photography and the pressure drop was measured as a function of the required operating parameters. Experimental correlations were used to estimate droplet sizes over flow conditions similar to that which would be experienced in the actual combustor. The results of this experiment were used to select the desired geometric parameters for the proposed final injector design and a CAD model was generated. Eventually, the new injector will be fabricated and tested to provide final validation of the design prior to use in the combustion test apparatus.

Performance Characteristics of Airlift Pumps with Vortex Induced by Tangential Fluid Injection

The effect of the swirl component of air injection on the performance of an airlift pump was examined experimentally. An airlift pump is a device that pumps a liquid or slurry using only gas injection. In this study, the liquid used was water and the injected gas was air. The effect of the air swirl was determined by measuring the water discharge from an airlift pump with an air injection nozzle in which the air flow had both axial and tangential components and then repeating the tests with a nozzle with only axial injection. The induced water flow was measured using an orifice meter in the supply pipeline. Tests were run for air pressures ranging from 10 to 30 pounds per square inch, gauge (psig), at flow rates from 5 standard cubic feet per minute (scfm) up the maximum values attainable at the given pressure (usually in the range from 20 to 35 scfm). The nozzle with only axial injection produced a water flow rate that wasequivalent to or better than that induced by the nozzle with swirl. The swirl component of air injection was found to be detrimental to pump performance for all but the smallest air injection flow rate. Optimum efficiency was found for air injection pressures of 10 psig to 15 psig. In addition, the effect of using auxiliary tangential injection of water to create a swirl component in the riser before air injection on the overall capacity (i.e., flow rate) and efficiencyof the pump was examined. Auxiliary tangential water injection was found to have no beneficial effect on the pump capacity or performance in the present system.

Clinical Study Monitoring the pH on Tooth Surfaces in Patients with and without Erosion

The aim of this study was to compare tooth surface pH after drinking orange juice or water in 39 patients with dental erosion and in 17 controls. The following investigations were carried out: measurement of pH values on selected tooth surfaces after ingestion of orange juice followed by ingestion of water (acid clearance), measurement of salivary flow rate and buffering capacity. Compared with the controls, patients with erosion showed significantly greater decreases in pH after drinking orange juice, and the pH stayed lower for a longer period of time (p < 0.05). Saliva parameters showed no significant differences between the two patient groups except for a lower buffering capacity at pH 5.5 in the erosion group.

Microbiota in the oral subgingival biofilm is associated with obesity in adolescence

To test the hypothesis whether microbiota in oral biofilm is linked with obesity in adolescents we designed this cross-sectional study. Obese adolescents (n = 29) with a mean age of 14.7 years and normal weight subjects (n = 58) matched by age and gender were examined with respect to visible plaque index (VPI%) and gingival inflammation (bleeding on probing (BOP%)). Stimulated saliva was collected. They answered a questionnaire concerning medical history, medication, oral hygiene habits, smoking habits, and sociodemographic background. Microbiological samples taken from the gingival crevice was analyzed by checkerboard DNA-DNA hybridization technique. The sum of bacterial cells in subgingival biofilm was significantly associated with obesity (P < 0.001). The link between sum of bacterial cells and obesity was not confounded by any of the studied variables (chronic disease, medication, VPI%, BOP%, flow rate of whole saliva, or meal frequency). Totally 23 bacterial species were present in approximately threefold higher amounts, on average, in obese subjects compared with normal weight controls. Of the Proteobacteria phylum, Campylobacter rectus and Neisseria mucosa were present in sixfold higher amounts among obese subjects. The association between obesity and sum of bacterial cells in oral subgingival biofilm indicates a possible link between oral microbiota and obesity in adolescents.

Best combination of pre-stimulation and latency period duration before cluster attachment for efficient oxytocin release and milk ejection in cows with low to high udder-filling levels

Experiments were designed to investigate the suitability of a combination of a short manual teat stimulation with a short latency period before teat cup attachment to induce and maintain oxytocin release and milk ejection without interruption. In Experiment 1, seven dairy cows in mid lactation were manually pre-stimulated for 15, 30 or 45 s, followed by either 30 s or 45 s of latency period. It was shown that all treatments induced a similar release of oxytocin without interruption until the end of milking. In particular, the latency period of up to 45 s did not cause a transient decrease of oxytocin concentration. In Experiment 2, milking characteristics were recorded in seven cows each in early, mid, and late lactation, respectively. Because the course of milk ejection depends mainly on the degree of udder filling, individual milkings were classified based on the actual degree of udder filling which differs between lactational stages but also between morning and evening milkings. All animals underwent twelve different udder preparation treatments, i.e. 15, 30, or 45 s of pre-stimulation followed by latency periods of 0, 30, 45, or 60 s. Milking characteristics were recorded. Total milk yield, main milking time and average milk flow rate did not differ between treatments if the degree of udder filling at the start of milking was >40% of the maximum storage capacity. However, if the udder filling was <40%, main milking time was decreased with the duration of a latency period up to 45 s, independent of duration of pre-stimulation. Average milk flow at an udder filling of <40% was highest after a pre-stimulation of 45 s followed by a latency period of another 45 s. In contrast, average milk flow reached its lowest values at a pre-stimulation of 15 s without additional latency period. However, average milk flow after a 15-s pre-stimulation increased with increasing latency period. In conclusion, a very short pre-stimulation when followed by a latency period up to 45 s before teat cup attachment remains a suitable alternative for continuous stimulation to induce milk ejection.

A novel interface for hybrid mock circulations to evaluate ventricular assist devices

This paper presents a novel mock circulation for the evaluation of ventricular assist devices (VADs), which is based on a hardware-in-the-loop concept. A numerical model of the human blood circulation runs in real time and computes instantaneous pressure, volume, and flow rate values. The VAD to be tested is connected to a numerical-hydraulic interface, which allows the interaction between the VAD and the numerical model of the circulation. The numerical-hydraulic interface consists of two pressure-controlled reservoirs, which apply the computed pressure values from the model to the VAD, and a flow probe to feed the resulting VAD flow rate back to the model. Experimental results are provided to show the proper interaction between a numerical model of the circulation and a mixed-flow blood pump.