Lithium ion conducting polymer electrolytes based on alternating maleic anhydride copolymer with oligo-oxyethylene side chains

A comb polymer with oligo-oxyethylene side chains of the type -(CH2CB2O)(12)CH3 was prepared from methyl vinyl ether/maleic anhydride copolymer and poly (ethylene glycol) methyl ether. The polymer can dissolve LiClO4 salt to form homogeneous amorphous polymer electrolyte. The ac ion conduction was measured using the complex impedance method, and conductivities were investigated as functions of temperatures and salt concentration. The complexes were first found to have two classes of glass transition which increase with increasing salt content, The optimum conductivity attained at 25 degrees C is in the order of 5.50 x 10(-6)Scm(-1). IR spectroscopy was used to study the cation-polymer interaction.

THE EFFECT ON PHYSICAL-PROPERTIES OF THE SUBSTITUTION OF CA OR BA FOR SR IN NDSRNIO4

A new solid solution series, NdSr(1-x)M(x)NiO(4) (M = Ca: 0.0 less than or equal to x less than or equal to 1.0; M = Ba: 0.0 less than or equal to x less than or equal to 0.6), was synthesized by solid state reaction, and the structures, magnetic and electrical properties and optical spectra of this series have been studied. All the samples crystalized in tetragonal systems, with the exception of NdCaNiO4, which crystallized in the orthohombic system. IR spectra of NdSr1-xCaxNiO4 indicated that the lengths of two Ni-O bonds decrease with increasing Ca content. The electrical conduction changed from metallic-type to semiconductive-type when x greater than or equal to 0.4 (M = Ca, Ba), and the room temperature resistivities of NdSr1-xCaxNiO4 increased with the increase of Ca content. Magnetic susceptibility measurements revealed that Ni+3 ions in all the samplies were in low-spin state over the temperature range 77-300 K.

GAMMA-RADIATION INDUCED CROSS-LINKED PEO-LICLO4 SOLID-ELECTROLYTE SYSTEM

Aimed at raising the room temperature ionic conductivity of PEO-based solid polymer electrolyte and considered that the ionic conduction preferentially occurs in the amorphous phase, we lightly crosslinked the high MW PEO through gamma-irradiation and further suppressed the residual crystallinity by plasticizing with propylene carbonate. By incorporating LiClO4 salt to the above described polymer host, the ambient (25 degrees C) ionic conductivity of the electrolyte system could reach as high as 6.8 X 10(-4) S/cm. As the electrolyte was a crosslinked system, it was mechanically self-supportable. Based on the preliminary results of the electrochemical performance of the secondary lithium battery, assembled by using this kind of solid electrolyte and polyaniline as positive electrode, it is realized that the electrolyte thus prepared is of high expectancy.

IONIC-CONDUCTIVITY AND DYNAMIC MECHANICAL RELAXATION OF A 2-COMPONENT EPOXY NETWORK-LICLO4 ELECTROLYTE SYSTEM

The correlation between mechanical relaxation and ionic conductivity was investigated in a two-component epoxy network-LiClO4 electrolyte system. The network was composed of diglycidyl ether of polyethylene glycol (DGEPEG) and triglycidyl ether of glycerol (TGEG). The effects of salt concentration, molecular weight of PEG in DGEPEG and the proportion of DGEPEG (1000) in DGEPEG/TGEG ratio on the ionic conductivity and the mechanical relaxation of the system were studied. It was found that, among the three influential factors, the former reinforces the network chains, reduces the free volume fraction and thus increases the relaxation time of the segmental motion, which in turn lowers the ionic conductivity of the specimen. Conversely, the latter two increase the free volume and thus the chain flexibility, showing an opposite effect. From the iso-free-volume plot of the shift factor log at and reduced ionic conductivity, it is noted that the plot can be used to examine the temperature dependence of segmental mobility and seems to be useful to judge whether the incorporated salt has been dissociated completely. Besides, the ionic conductivity and relaxation time at constant reference temperature are linearly correlated with each other in all the three cases. This result gives an additional experimental confirmation of the coordinated motion model of the ionic hopping with the moving polymer chain segment, which is generally used to explain the ionic conduction in non-glassy amorphous polymer electrolytes.

STUDIES ON INTERFACIAL PHENOMENA OF POLYCRYSTALLINE HG1-XCDXTE THIN-FILM ELECTRODE POLYSULFIDE REDOX SOLUTION

Electrode capacitance and photocurrent spectra of electrodeposited polycrystalline Hg1-xCdxTe thin films of varying (1-x) were measured in polysulfide redox solution, hence the flatband potentional PHI(fb) and the bandgap E(g) of Hg1-xCdxTe thin films obtained. It was of interest to find out that only the location of conduction band E(c) shifts negatively with increasing (1-x) while the valence band E(v), is almost constant. The experimental open circuit photovoltage V0 is smaller than theoretical value V(max) calculated through flatband potential PHI(fb), therefore there is a possibility of promoting the experimental open circuit photovoltage.

THE OPTICAL AND ELECTRICAL-PROPERTIES OF DYSPROSIUM AND YTTERBIUM MONOPHOSPHIDES

Dysprosium and ytterbium monophosphides have been prepared by the solid state reaction. The optical and electrical properties have been studied. Evidence that DyP and YbP are semiconductors has been obtained from the study of the absorption spectrum, the negative temperature coefficient of resistance and the rectifying effect. Their energy gaps are determined as 1.15 eV for DyP and 1.30 eV for YbP, electric conduction type is n-type, resistivities are about 10(-2) ohm cm and Hall mobility is 8.5-80 cm2/Vs. The p-n junction is formed on the LnP/Si.

INVESTIGATION OF THE PHOTOELECTRONIC PROPERTIES OF RARE-EARTH MONOPHOSPHIDES

The optical, electrical and photoelectronic properties of rare earth monophosphides (LnP, Ln = La, Nd, Sm and Y) have been studied. The experimental results indicate that their resistivities are low, the electric conduction in all of them is N-type, the energy gaps of LaP, NdP, SmP and YP are 1.46eV, 1.15eV, 1.1eV and 1.0eV, respectively. The SmP/Si and YP/Si junctions exhibit the photovoltaic effect. They may be used as photoelectronic sensors.

THE PHOTOELECTRIC PROPERTIES OF THIN-FILMS OF RARE-EARTH MONOPHOSPHIDES

The optical, electrical and photoelectric properties of rare earth monophosphides (LnP, Ln = La, Nd, Sm, Y, Dy and Yb) have been studied in thin films. The films exhibit semiconducting behaviour with energy gaps of 1.0-1.46 eV and n-type electrical conduction. Their resistivities are 10(-2) OMEGA-cm with corresponding Hall mobilities of 8.5-400 cm2 V-1 s-1. The films are deposited on a p-type silicon substrate in vacuum. Voltage-current characteristic measurements show that a p-n junction has been formed between LnP and silicon. Spectral sensitivity and a photovoltaic effect have been observed in LnP-Si junctions. They may be useful photoelectric materials.

STUDIES ON THE ELECTRICAL AND MAGNETIC-PROPERTIES FOR LASR2-XCAXV3O9+/-Y

The electrical and magnetical properties of LaSr(2-x)Ca(x)V3O9 +/- y have been investigated. The compounds are antiferromagnetic. They show a metallic conduction other than semiconductivity. The trivalent and tetravalent vanadium ions coexist in the system. The magnetic susceptibility increases and the resistivity decreases at room temperature with the increase of x value. It is shown that the change of the valency state of vanadium obviously influences the electrical and magnetical properties of the system.

OBSERVATION OF MOSSBAUER-EFFECT IN THE HIGH-TEMPERATURE SUPERCONDUCTOR EUBA2CU3O7-X WITH DC ELECTRIC-CURRENT

The difference between the Mossbauer parameters for EuBa2Cu3O7-x with dc electric current and those without dc electric current at 83 K has been observed. The change in isomer shift, electric quadrupole splitting and the asymmetry parameter of the electric field gradient at the Eu-151 nucleus may be caused by the movement of a mass of conduction electrons along a certain direction in the EuBa2Cu3O7-x crystal with a layered structure.

强流脉冲离子束辐照45钢表面热效应的模拟

以Fourier瞬态传热方程为基础,确定了强流脉冲离子束(HIPIB)热效应的基本传热方程,对靶材45钢进行不同能量参数的HIPIB辐照热效应的模拟计算.针对离子注入金属内部的情况,在模拟束流加载方式上分别采用体加载和面加载,比较了两种加载计算结果之间的差距.本算法的另一个改进就是在高能量辐照下,用单元死活法对蚀坑部分材料的消失进行模拟.结果表明,用单元死活法模拟单元的失效,更能符合HIPIB辐照金属表面热效应的蚀坑机制;单元死活法对靶材的升温过程没有明显影响,但对冷却阶段,可以显著提高模拟的精度.

南海北部大陆边缘盆地深部地热特征用地球动力学演化

This report is a conclusion of the major research outcome during my post-doctoral residence of research and work. Its content covers the researches of the deep thermal characteristic and dynamics evolution beneath the northern margin basin of South China Sea. In this report, the each other action and effect between lithosphere ad mantle convection were regarded by the combine of deep and shallow study, subdivision from whole to part, and pay equal attention to determine the nature and fixed quantity. The investigative method we used in this report is geothermal and gravity methods. By the help of geological model and geophysics modeling, we calculated lithosphere thermal structure, rheology structure and mantle convection. Firstly, the report introduces concisely the purpose and the previous achievement to this research. Then, it analyzed the characteristic of heat flow on South China Sea. The structure of deep temperature and thermal has been calculated in some models of heat generation and conduction. The rock rheology structure also was computed by the relationship between temperature and viscosity. All these calculations were finished under the guidelines of combine with geology and geophysics. Meanwhile, the fields both deep mantle convection and small scale upper mantle convection are computed. Beside, the density and temperature disorder resulted by mantle convection were also computed with the convection field. After these, the report bring the contribution of local field of mantle convection, thermal construct and effective viscosity beneath the northern margin basin of South China Sea. And, base on the tectonic background and evolution feature, this report discussion the evolution mechanism of south China Sea and its northern margin basin. The end of this report, the main conclusion of this research was summarized and brings out.

单（多）井抽灌对浅部地温场的影响研究

The technique of energy extraction using groundwater source heat pumps, as a sustainable way of low-grade thermal energy utilization, has widely been used since mid-1990's. Based on the basic theories of groundwater flow and heat transfer and by employing two analytic models, the relationship of the thermal breakthrough time for a production well with the effect factors involved is analyzed and the impact of heat transfer by means of conduction and convection, under different groundwater velocity conditions, on geo-temperature field is discussed.A mathematical model, coupling the equations for groundwater flow with those for heat transfer, was developed. The impact of energy mining using a single well system of supplying and returning water on geo-temperature field under different hydrogeological conditions, well structures, withdraw-and-reinjection rates, and natural groundwater flow velocities was quantitatively simulated using the finite difference simulator HST3D. Theoretical analyses of the simulated results were also made. The simulated results of the single well system indicate that neither the permeability nor the porosity of a homogeneous aquifer has significant effect on the temperature of the production segment provided that the production and injection capability of each well in the aquifers involved can meet the designed value. If there exists a lower permeable interlayer, compared with the main aquifer, between the production and injection segments, the temperature changes of the production segment will decrease. The thicker the interlayer and the lower the interlayer permeability, the longer the thermal breakthrough time of the production segment and the smaller the temperature changes of the production segment. According to the above modeling, it can also be found that with the increase of the aquifer thickness, the distance between the production and injection screens, and/or the regional groundwater flow velocity, and/or the decrease of the production-and-reinjection rate, the temperature changes of the production segment decline. For an aquifer of a constant thickness, continuously increase the screen lengths of production and injection segments may lead to the decrease of the distance between the production and injection screens, and the temperature changes of the production segment will increase, consequently.According to the simulation results of the single well system, the parameters, that can cause significant influence on heat transfer as well as geo-temperature field, were chosen for doublet system simulation. It is indicated that the temperature changes of the pumping well will decrease as the aquifer thickness, the distance between the well pair and/or the screen lengths of the doublet increase. In the case of a low permeable interlayer embedding in the main aquifer, if the screens of the pumping and the injection wells are installed respectively below and above the interlayer, the temperature changes of the pumping well will be smaller than that without the interlay. The lower the permeability of the interlayer, the smaller the temperature changes. The simulation results also indicate that the lower the pumping-and-reinjection rate, the greater the temperature changes of the pumping well. It can also be found that if the producer and the injector are chosen reasonably, the temperature changes of the pumping well will decline as the regional groundwater flow velocity increases. Compared with the case that the groundwater flow direction is perpendicular to the well pair, if the regional flow is directed from the pumping well to the injection well, the temperature changes of the pumping well is relatively smaller.Based on the above simulation study, a case history was conducted using the data from an operating system in Beijing. By means of the conceptual model and the mathematical model, a 3-D simulation model was developed and the hydrogeological parameters and the thermal properties were calibrated. The calibrated model was used to predict the evolution of the geo-temperature field for the next five years. The simulation results indicate that the calibrated model can represent the hydrogeological conditions and the nature of the aquifers. It can also be found that the temperature fronts in high permeable aquifers move very fast and the radiuses of temperature influence are large. Comparatively, the temperature changes in clay layers are smaller and there is an obvious lag of the temperature changes. According to the current energy mining load, the temperature of the pumping wells will increase by 0.7°C at the end of the next five years. The above case study may provide reliable base for the scientific management of the operating system studied.

Investigation of platinum utilization and morphology in catalyst layer of polymer electrolyte fuel cells

Platinum utilization in the gas-diffusion catalyst layer and thin-film catalyst layer is investigated. The morphology of PTFE and Nafion in a simulated catalyst layer is examined by scanning electronmicroscopy (SEM) and transmission electron microscopy (TEM). The results show that the platinum utilization of the thin-film catalyst layer containing only Pt/C and Nafion is 45.4%. The low utilization is attributed to the fact that the electron conduction of many catalyst particles is impaired by some thick Nafion layers or clumps. For the gas-diffusion (E-TEK) electrode, the platinum utilization is mainly affected by the proton conduction provided by Nafion. The blocking effect of PTFE on the active sites is not serious. When the electrode is sufficiently impregnated with Nafion by an immersion method, the platinum utilization can reach 77.8%. Transmission electron micrographs reveal that although some thick Nafion layers and clumps are observed in the Pt/C + Nafion layer, the distribution of Nafion in the catalyst layer is basically uniform. The melted PTFE disperses in the catalyst layer very uniformly. No large PTFE clumps or wide net-like structure is observed. The reactant gas may have to diffuse evenly in the catalyst layer. (C) 1999 Elsevier Science S.A. All rights reserved.

Contact Sensors for Dexterous Robotic Hands

This thesis examines a tactile sensor and a thermal sensor for use with the Utah-MIT dexterous four fingered hand. Sensory feedback is critical or full utilization of its advanced manipulatory capabilities. The hand itself provides tendon tensions and joint angles information. However, planned control algorithms require more information than these sources can provide. The tactile sensor utilizes capacitive transduction with a novel design based entirely on silicone elastomers. It provides an 8 x 8 array of force cells with 1.9 mm center-to-center spacing. A pressure resolution of 8 significant bits is available over a 0 to 200 grams per square mm range. The thermal sensor measures a material's heat conductivity by radiating heat into an object and measuring the resulting temperature variations. This sensor has a 4 x 4 array of temperature cells with 3.5 mm center-to-center spacing. Experiments show that the thermal sensor can discriminate among material by detecting differences in their thermal conduction properties. Both sensors meet the stringent mounting requirements posed by the Utah-MIT hand. Combining them together to form a sensor with both tactile and thermal capabilities will ultimately be possible. The computational requirements for controlling a sensor equipped dexterous hand are severe. Conventional single processor computers do not provide adequate performance. To overcome these difficulties, a computational architecture based on interconnecting high performance microcomputers and a set of software primitives tailored for sensor driven control has been proposed. The system has been implemented and tested on the Utah-MIT hand. The hand, equipped with tactile and thermal sensors and controlled by its computational architecture, is one of the most advanced robotic manipulatory devices available worldwide. Other ongoing projects will exploit these tools and allow the hand to perform tasks that exceed the capabilities of current generation robots.