Transporte de nano SiO₂ por migración a través de materiales cementantes

Uno de los nanos materiales más investigados actualmente es la nano-sílice, la cual ha despertado el interés de muchos investigadores debido a que está aportando grandes beneficios a los materiales base cemento. La nano-sílice ha demostrado que mejora las propiedades de los materiales cementantes tanto en estado fresco como en endurecido. Puede modificar las propiedades reológicas o la trabajabilidad en estado fresco, así como la resistencia a la compresión y la porosidad de las estructuras después de la etapa de endurecimiento. Es por esto que estas nano-partículas representan la oportunidad de realizar importantes avances que permitan optimizar el uso de los recursos actuales y el aprovechamiento de los materiales cementantes. En este trabajo, se está estudiando la posibilidad de utilizar la nano-sílice como un tratamiento superficial que ayude a disminuir el impacto del medio ambiente en estructuras en servicio que puedan presentar un cierto deterioro. Se analiza la utilización de nano-partículas en concreto en estado endurecido con el fin de mejorar su desempeño y sus aspectos de durabilidad. Por medio del método de migración electroquímica, basado en el transporte de partículas con cierta carga bajo la acción de un campo eléctrico, se favorece la penetración de nano-partículas de sílice hacia el interior de un mortero de cemento Portland desde una cara expuesta a una solución coloidal. Las partículas se mueven por acción del campo eléctrico hacia el ánodo situado en la cara opuesta de la probeta de mortero, dando lugar a una interacción química con la microestructura de la matriz cementante. Se ha observado que las partículas de sílice en esta solución coloidal empiezan a aglomerarse después de cierto periodo de tiempo y solidifican sobre la superficie expuesta de la probeta de mortero. Este material sólido ocasiona que la cantidad de corriente que circula por el circuito disminuya y por consiguiente baje la efectividad del mismo, ya que las partículas con carga eléctrica se mueven con mayor dificultad en medios solidos que en líquidos. Se encontró que la incorporación de nano-partículas de sílice a la matriz de mortero endurecido puede afectar el desempeño de una manera positiva frente a la penetración de cloruros, carbonatación y absorción de agua por capilaridad. De acuerdo a las respuestas eléctricas durante el tratamiento, se encontró que la resistencia eléctrica de las probetas aumenta, lo cual puede relacionarse con la modificación del sistema poroso debido al efecto filler de las nano-partículas; es decir, al refinar los poros, las cargas eléctricas encuentran menos espacio para moverse. Además las nano-partículas afectan químicamente a las fases de la pasta del cemento, ya que se encontró por microscopia electrónica de barrido que a una distancia entre 1.5 y 2 mm, aparecen aglomerados que enriquecen de silicio a las fases de la matriz del mortero y en otros casos, la migración cambia totalmente la apariencia del mortero y ocasiona valores de relaciones Ca/Si muy por debajo de los valores convencionales registrados en la literatura, con lo que es posible pensar que puede existir una actividad puzzolanica.

UHMWPE/SBA-15 nanocomposites synthesized by in situ polymerization

Different nanocomposites have been attained by in situ polymerization based on ultra-high molecular weight polyethylene (UHMWPE) and mesoporous SBA-15, this silica being used for immobilization of the FI catalyst bis [N-(3-tert-butylsalicylidene)-2,3,4,5,6-pentafluoroanilinato] titanium (IV) dichloride and as filler as well. Two distinct approaches have been selected for supporting the FI catalyst on the SBA-15 prior polymerization. A study on polymerization activity of this catalyst has been performed under homogenous conditions and upon heterogenization. A study of the effect of presence of mesoporous particles and of the immobilization method is also carried out. Moreover, the thermal characterization, phase transitions and mechanical response of some pristine UHMWPEs and UHMWPE/SBA-15 materials have been carried out. Relationships with variations on molar mass, impregnation method of catalyst and final SBA-15 content have been established.

Avaliação da eficácia in vivo da L-arginina na elasticidade da pele

Dissertação (mestrado)—Universidade de Brasília, Faculdade de Ciências da Saúde, Programa de Pós-Graduação em Ciências da Saúde, 2012.

Sustentabilidade do betão: Comportamento de betões com substituição parcial de cimento portland por adições quase inertes

Os betões atuais são materiais com custos extremamente competitivos devido ao baixo custo do cimento Portland. Contudo, os elevados níveis de emissões de C02 gerados na sua produção provocam o aumento do custo final do produto, tanto económico como ambiental. Devido a esta situação algumas adições têm sido estudadas como alternativas para substituir parcialmente os conteúdos de cimento no fabrico de betão. Uma vez que existem grandes quantidades de pó de mármore inutilizadas na região de Évora decidiu-se avaliar o seu comportamento. O pó de mármore foi adicionado em certas percentagens de forma a reduzir os conteúdos de cimento, permitindo avaliar se este iria manter e/ou melhorar as características de resistência à compressão e trabalhabilidade do betão. Além de avaliado o comportamento desta adição, o mesmo foi também comparado com a adição de filer calcário nas mesmas percentagens. Os resultados obtidos demonstraram a exequibilidade da utilização de ambas as adições. ABSTRACT: Concretes currently used in construction are materials with very competitive costs due to the low cost of Portland cement. However, high levels of C02 emissions generated in its production cause an increase of the final cost of the product, both economically and environmentally. Due to this situation, some additions have been studied as alternatives to replace partially cement contents in concrete production. Since there are large quantities of marble dust in the region of Évora, it was decided to evaluate his behavior. The marble dust was added in known percentages so the cement contents could be reduced, allowing evaluating if it will maintain and/or improve the characteristics of the compressive strength and workability of the concrete. ln addition to evaluating the behavior of marble dust, this addition was also compared with the addition of limestone filler in the same percentages. The results demonstrated the feasibility of using both additions.

Novos monômeros obtidos a partir do metacrilato de glicidila, bisfenol A e 4, 4 isopropilidenodicicloexanol : síntese, caracterização estrutural e propriedades de compósitos para utilização em resinas de restauração dental

Nowadays, composite resins are the direct restorative materials more important in dental clinical performance, due to their versatility and aesthetic excellence. Bis-GMA (2,2-bis[4(2-hydroxy-3-metacryloxypropoxy)phenil]propane) is the base monomer more frequently used in restorative composite resins. However, this monomer presents some disadvantages, such as high viscosity and two aromatic rings in its structure that can promote allergic reactions to the humans. In this work, the main purpose was to synthesize new monomers from glycidyl methacrylate to use in dental restorative materials. Structural characterization of the monomers was carried out through FTIR and NMR 1H, and eight composites were produced from the new monomers, by addition of silane-treated alumino silicate particles (inorganic filler) and a photocuring system (camphorquinone and ethyl 4-dimethylaminebenzoate). The composites were analyzed by environmental scanning electronic microscopy and the water sorption and solubility, compressive strength and elastic modulus were determined. A commercial composite resin [Z100 (3M)] was used to comparison effect. The new composites presented general characteristics similar to the commercial ones; however, they didn t present the properties expected. This behavior was attributed to the lower degree of monomer reaction and to the granulometry and size distribution of the mineral filler in the polymeric matrix

Sinterização de matrizes cerâmicas à base de alumina reforçadas por carbetos a partir de precursores poliméricos

Ceramic composites produced with polymerics precursors have been studied for many years, due to the facility of obtaining a complex shape, at low temperature and reduces cost. The main objective of this work is to study the process of sintering of composites of ceramic base consisting of Al2O3 and silicates, reinforced for NbC, through the technique of processing AFCOP, as well as the influence of the addition of LZSA, ICZ and Al as materials infiltration in the physical and mechanical properties of the ceramic composite. Were produced ceramic matrix composites based SiCxOy e Al2O3 reinforced with NbC, by hidrosilylation reaction between D4Vi and D1107 mixtured with Al2O3 as inert filler, Nb and Al as reactive filler. The specimens produced were pyrolised at 1200, 1250 and 1400°C and infiltred with Al, ICZ and LZSA, respectively. Density, porosity, flexural mechanical strength and fracture surface by scanning electron microscopy were evaluated. The microstructure of the composites was investigated by X-ray diffraction to identify the presence of crystalline phases. The composites presented apparent porosity varying of 31 up to 49% and mechanical flexural strength of 14 up to 34 MPa. The infiltration process improviment of the densification and reduction of the porosity, as well as increased the values of mechanical flexural strength. The obtained phases had been identified as being Al3Nb, NbSi2, Nb5S3, Nb3Si and NbC. The samples that were submitted the infiltration process presented a layer next surface with reduced pores number in relation to the total volume

Selective hydrogenation by novel composite supported Pd egg-shell catalysts

Two organic–inorganic mixed phase supports were prepared, comprising an alumina filler and polymers of different chemical nature. Four low loaded Pd catalysts were prepared. Good activities and selectivities were obtained during the hydrogenations of styrene, 1-heptyne and 2,3-butanedione. The catalysts were found to have excellent mechanical properties and could be used in applications needing high attrition resistance and crushing strength. In this sense, processes for fine chemicals using slurry reactors or processes for commodities using long packed beds could advantageously use them.

Dissipation of triadimefon on the solid/gas interface

The dissipation or triadimefon, as pure solid and in the Bayleton 5 commercial formulation, was studied under controlled and natural conditions. Volatilization and photodegradation were shown to be the main dissipation processes. The volatilization results can be described by an empirical model assuming exponential decay of the volatilization rate. The filler of the commercial formulation is determinant for the volatilization but has little effect on the photodegradation rates. The main photoproducts were identified and a reaction mechanism proposed. (C) 2001 Elsevier Science Ltd. All rights reserved.

CHARACTERIZATION OF THERMAL AND MECHANICAL PROPERTIES OF POLYPROPYLENE–BASED COMPOSITES FOR FUEL CELL BIPOLAR PLATES AND DEVELOPMENT OF EDUCATIONAL TOOLS IN HYDROGEN AND FUEL CELL TECHNOLOGIES

In this project we developed conductive thermoplastic resins by adding varying amounts of three different carbon fillers: carbon black (CB), synthetic graphite (SG) and multi–walled carbon nanotubes (CNT) to a polypropylene matrix for application as fuel cell bipolar plates. This component of fuel cells provides mechanical support to the stack, circulates the gases that participate in the electrochemical reaction within the fuel cell and allows for removal of the excess heat from the system. The materials fabricated in this work were tested to determine their mechanical and thermal properties. These materials were produced by adding varying amounts of single carbon fillers to a polypropylene matrix (2.5 to 15 wt.% Ketjenblack EC-600 JD carbon black, 10 to 80 wt.% Asbury Carbons’ Thermocarb TC-300 synthetic graphite, and 2.5 to 15 wt.% of Hyperion Catalysis International’s FIBRILTM multi-walled carbon nanotubes) In addition, composite materials containing combinations of these three fillers were produced. The thermal conductivity results showed an increase in both through–plane and in–plane thermal conductivities, with the largest increase observed for synthetic graphite. The Department of Energy (DOE) had previously set a thermal conductivity goal of 20 W/m·K, which was surpassed by formulations containing 75 wt.% and 80 wt.% SG, yielding in–plane thermal conductivity values of 24.4 W/m·K and 33.6 W/m·K, respectively. In addition, composites containing 2.5 wt.% CB, 65 wt.% SG, and 6 wt.% CNT in PP had an in–plane thermal conductivity of 37 W/m·K. Flexural and tensile tests were conducted. All composite formulations exceeded the flexural strength target of 25 MPa set by DOE. The tensile and flexural modulus of the composites increased with higher concentration of carbon fillers. Carbon black and synthetic graphite caused a decrease in the tensile and flexural strengths of the composites. However, carbon nanotubes increased the composite tensile and flexural strengths. Mathematical models were applied to estimate through–plane and in–plane thermal conductivities of single and multiple filler formulations, and tensile modulus of single–filler formulations. For thermal conductivity, Nielsen’s model yielded accurate thermal conductivity values when compared to experimental results obtained through the Flash method. For prediction of tensile modulus Nielsen’s model yielded the smallest error between the predicted and experimental values. The second part of this project consisted of the development of a curriculum in Fuel Cell and Hydrogen Technologies to address different educational barriers identified by the Department of Energy. By the creation of new courses and enterprise programs in the areas of fuel cells and the use of hydrogen as an energy carrier, we introduced engineering students to the new technologies, policies and challenges present with this alternative energy. Feedback provided by students participating in these courses and enterprise programs indicate positive acceptance of the different educational tools. Results obtained from a survey applied to students after participating in these courses showed an increase in the knowledge and awareness of energy fundamentals, which indicates the modules developed in this project are effective in introducing students to alternative energy sources.

The Impact of the "Not Sure" Option on Lineup Identification Decisions

Law enforcement officials routinely rely on eyewitness identification evidence to solve crimes. Nonetheless, this form of evidence is prone to errors. Researchers have previously attempted to examine conditions under which such errors can be reduced. The present study examines whether giving witnesses an explicit not sure response option increases the accuracy of lineup identification decisions. 251 participants watched a mock crime video before viewing a lineup that either included the perpetrator, or was made up of innocent suspects. Results indicated that witnesses provided with a not sure option made fewer false identifications, fewer filler identifications, and a similar number of correct identifications as witnesses who were not provided with this option. Furthermore, these benefits occurred regardless of whether witnesses received otherwise biased or unbiased instructions. Results suggest that the inclusion of an explicit not sure response option is a simple procedure that can increase the quality of eyewitness lineup decisions.

Maltodextrin-incorporated-vacuum-dried honey powder: processing and stability

Honey is rich in sugar content and dominated by fructose and glucose that make honey prone to crystallize during storage. Due to honey composition, the anhydrous glass transition temperature of honey is very low that makes honey difficult to dry alone and drying aid or filler is needed to dry honey. Maltodextrin is a common drying aid material used in drying of sugar-rich food. The present study aims to study the processing of honey powder by vacuum drying method and the impact of drying process and formulation on the stability of honey powder. To achieve the objectives, the series of experiments were done: investigating of maltodextrin DE 10 properties, studying the effect of drying temperature, total solid concentration, DE value, maltodextrin concentration and anti-caking agent on honey powder processing and stability. Maltodextrin provide stable glass compared to lower molecular weight sugars. Dynamic Dew Point Isotherm (DDI) data could be used to determine amorphous content of a system. The area under the first derivative curve from DDI curve is equal to the amount of water needed by amorphous material to crystallize. The drying temperature affected the amorphous content of vacuum-dried honey powder. The higher temperature seemed to result in honey powder with more amorphous component. The ratio of maltodextrin affected more significantly the stability of honey powder compared to the treatments of total solids concentration, DE value and drying temperature. The critical water activity of honey powder was lower than water activity of the equilibrium water content corresponding to BET monolayer water content. Addition of anti-caking agent increased stability and flow-ability of honey powder. Addition of Calcium stearate could inhibit collapse of the honey powder during storage.

Láser Q-Switched en el manejo de ocronosis exógena: revisión sistemática de la literatura

Antecedentes: La ocronosis Exógena (OE) es una enfermedad subdiagnosticada y de difícil manejo (1). El láser Q-Switched (QS) surge como una alternativa para el tratamiento de esta (2). Objetivo: Describir las características de los pacientes, del láser QS y los desenlaces en el tratamiento de OE. Métodos: Se realizó una búsqueda de la literatura en las bases PubMed, Embase, PMC, Scielo, Elselvier, BMJ Case Reports, Journal of Medical Case Reports, Cases Journal e International Medical Case Reports Journal, desde enero del 2000 a marzo del 2016, pacientes con ocronosis exógena, 18 a 70 años, tratados con láser QS. Los artículos fueron evaluados mediante la herramienta de evaluación de validez y valor educativo de reportes de caso descrito por Pierson (3). Resultados: Se encontraron 256 artículos, 63 fueron seleccionados: 28 repetidos y 31 no cumplieron criterios de inclusión. Se escogieron 4 artículos que reportan 12 casos de pacientes con ocronosis exógena diagnosticada mediante estudio histopatológico y tratada con láser QS. Discusión: Hay poca experiencia con el láser QS en OE. En la práctica clínica se usa para tatuajes y patologías pigmentarias dérmicas con resultados satisfactorios. El pigmento dérmico en OE y la corta duración de pulso de láser QS, podrían ser el pilar de tratamiento para OE. Conclusión: El láser QS puede ser útil para el tratamiento en OE, con nivel de evidencia 3 y grado de recomendación D. Se sugiere realizar estudios clínicos con mayor grado de evidencia.

Seláceos do Farol das Lagostas (Bacia do Cuanza, Angola)

O presente trabalho consiste na apresentação da diversidade de seláceos do Farol das Lagostas pertencente à Bacia do Cuanza. Os condrichthyes são componentes comuns da fauna aquática desde o Paleozoico. No entanto, devido à natureza cartilaginosa do esqueleto, o registo paleontológico dos mesmos restringe-se, basicamente, às partes mineralizadas como dentes, dentículos dérmicos e espinhas cefálicas O lugar Farol das Lagostas contém uma fauna de seláceos relativamente rica e variada, representada neste estudo por cerca de 1.000 dentes isolados, além de outras peças esqueléticas. Foram identificados e descritos quarenta e quatro taxa, pertencentes às seguintes ordens: Hexanchiformes, Squaliformes, Pristiophoriformes, Squatiniformes, Lamniformes, Carcharhiniformes, Rajiformes e Myliobatiformes. Trata-se de uma diversidade faunística cuja maioria dos géneros possui representantes atuais. Os Carcharhiniformes representam 53% dos taxa identificados. Estão representadas as famílias Scyliorhinidae, Triakidae, Hemigaleidae, Carcharhinidae e Sphyrnidae, com 18 espécies. Verifica-se a presença de formas bentónicas e nectónicas que indicam condições térmicas moderadas, quentes e tropicais a temperadas, que habitam frequentemente zonas costeiras. A relação faunística identificada corresponde a uma zona litoral. Ora, considerando o conjunto de dados em face da presença de fauna pelágica e dos grandes predadores, especialmente Isurus hastalis e Carcharocles megalodon, podemos admitir que existisse então um Golfo relativamente largo de uma faixa Atlântica aberta (Antunes & Balbino, 2004); ABSTRACT: Selachians from Farol the Lagostas (Cuanza Basin, Angola) The present work consists of the presentation of diversity of selachians from Farol das Lagostas, which belongs to the Cuanza Basin. The condrichthyes are a part of aquatic fauna since the Paleozoic. However, due to the nature of the cartilaginous skeleton, the paleontological registration of the same ones is restricted to mineralized parts like teeth, dermal denticles and cephalic spines. The of formation, Farol das Lagostas has a fauna of selachian relatively rich and diverse, represented in this study for around 1.000 isolated teeth, and other skeletal parts. Forty four taxa were described and identified, belonging to the following orders: Hexanchiformes, Squaliformes, Pristiophoriformes, Squatiniformes, Lamniformes, Carcharhiniformes, Rajiformes e Myliobatiformes. It’s a faunal diversity whose most genera have current representatives. The Carcharhiniformes represente 53% of the identified taxa. The represented families are Scyliorhinidae, Triakidae, Hemigaleidae, Carcharhinidae e Sphyrnidae, with 18 species. There is presence of benthic and nektonic forms that indicate moderate thermal conditions, the temperate and tropical hot, often inhabit coastal areas. The identified faunal relation corresponds to a coastal zone. So, considering the data set, due to the presence of pelagic fauna and large predators, especially Isurus hastalis e Carcharocles megalodon, we can admit that then there was a relatively large Gulf of open Atlantic range (Antunes & Balbino, 2004).