Externalities of Shipping in the Gulf of Finland until 2015

During the last few years, the discussion on the marginal social costs of transportation has been active. Applying the externalities as a tool to control transport would fulfil the polluter pays principle and simultaneously create a fair control method between the transport modes. This report presents the results of two calculation algorithms developed to estimate the marginal social costs based on the externalities of air pollution. The first algorithm calculates the future scenarios of sea transport traffic externalities until 2015 in the Gulf of Finland. The second algorithm calculates the externalities of Russian passenger car transit traffic via Finland by taking into account both sea and road transport. The algorithm estimates the ship-originated emissions of carbon dioxide (CO₂), nitrogen oxides (NO_x), sulphur oxides (SO_x), particulates (PM) and the externalities for each year from 2007 to 2015. The total NOx emissions in the Gulf of Finland from the six ship types were almost 75.7 kilotons (Table 5.2) in 2007. The ship types are: passenger (including cruisers and ROPAX vessels), tanker, general cargo, Ro-Ro, container and bulk vessels. Due to the increase of traffic, the estimation for NO_x emissions for 2015 is 112 kilotons. The NO_x emission estimation for the whole Baltic Sea shipping is 370 kilotons in 2006 (Stipa & al, 2007). The total marginal social costs due to ship-originated CO₂, NO_x, SO_x and PM emissions in the GOF were calculated to almost 175 million Euros in 2007. The costs will increase to nearly 214 million Euros in 2015 due to the traffic growth. The major part of the externalities is due to CO₂ emissions. If we neglect the CO2 emissions by extracting the CO₂ externalities from the results, we get the total externalities of 57 million Euros in 2007. After eight years (2015), the externalities would be 28 % lower, 41 million Euros (Table 8.1). This is the result of the sulphur emissions reducing regulation of marine fuels. The majority of the new car transit goes through Finland to Russia due to the lack of port capacity in Russia. The amount of cars was 339 620 vehicles (Statistics of Finnish Customs 2008) in 2005. The externalities are calculated for the transportation of passenger vehicles as follows: by ship to a Finnish port and, after that, by trucks to the Russian border checkpoint. The externalities are between 2 – 3 million Euros (year 2000 cost level) for each route. The ports included in the calculations are Hamina, Hanko, Kotka and Turku. With the Euro-3 standard trucks, the port of Hanko would be the best choice to transport the vehicles. This is because of lower emissions by new trucks and the saved transport distance of a ship. If the trucks are more polluting Euro 1 level trucks, the port of Kotka would be the best choice. This indicates that the truck emissions have a considerable effect on the externalities and that the transportation of light cargo, such as passenger cars by ship, produces considerably high emission externalities. The emission externalities approach offers a new insight for valuing the multiple traffic modes. However, the calculation of the marginal social costs based on the air emission externalities should not be regarded as a ready-made calculation system. The system is clearly in the need of some improvement but it can already be considered as a potential tool for political decision making.

Control de la temperatura i el llum mitjançant dispositius sense fils

El concepte Internet de les Coses va néixer fa molt poc, cap a l’any 2010, i es refereix a la connexió d’objectes a Internet, de manera que puguin interactuar en xarxa entre ells o amb les persones per transmetre o rebre informació, i realitzar, així, les accions programades en funció de les dades disponibles. Des de llavors la gran majoria d’institucions, tant públiques com privades, s’han interessat en aquest concepte, ja que pot suposar un augment molt important de la qualitat de vida de les persones, un estalvi de recursos i beneficis econòmics. D’aquí neix aquest Treball Final de Grau, ja que des de la Fundació Eduard Soler de Ripoll tenen el desig d’introduir-se en aquest camp. L’objectiu principal d’aquest Treball Final de Grau és crear una xarxa sense fils que pugui controlar la temperatura i la il·luminació de l’edifici C de la Fundació Eduard Soler i que, a més, es pugui connectar a Internet. Una de les conclusions a què he arribat gràcies a aquest treball és que la utilització d’eines de baix cost (Arduino, Xbee, MySQL, PHP...) permet introduir-se en l’apassionant món de l’Internet de les Coses i, a més, aconseguir molt bons resultats.

Neural mechanisms underlying adaptive actions after slips

An increase in cognitive control has been systematically observed in responses produced immediately after the commission of an error. Such responses show a delay in reaction time (post-error slowing) and an increase in accuracy. To characterize the neurophysiological mechanism involved in the adaptation of cognitive control, we examined oscillatory electrical brain activity by electroencephalogram and its corresponding neural network by event-related functional magnetic resonance imaging in three experiments. We identified a new oscillatory thetabeta component related to the degree of post-error slowing in the correct responses following an erroneous trial. Additionally, we found that the activity of the right dorsolateral prefrontal cortex, the right inferior frontal cortex, and the right superior frontal cortex was correlated with the degree of caution shown in the trial following the commission of an error. Given the overlap between this brain network and the regions activated by the need to inhibit motor responses in a stop-signal manipulation, we conclude that the increase in cognitive control observed after the commission of an error is implemented through the participation of an inhibitory mechanism.

Projecte executiu d'una instal·lació de climatització i control d'un habitatge unifamiliar

Moltes vegades l’usuari d’una instal•lació de climatització o calefacció, no dóna la suficient importància al sistema que l’hi ha de proporcionar un millor confort amb el màxim rendiment. Aquest confort és un factor determinant, entre molts d’altres, de la “qualitat de vida”. Mentre que el rendiment és un factor important a nivell econòmic i ecològic. Tot i tenir prevalença els aspectes d’estalvi energètic, aquests no impliquen haver de renunciar a un confort tèrmic i a un estalvi econòmic. Un dels aspectes que es centra el projecte és promoure l’ús racional de les fonts energètiques (solar, biomassa) per a la correcta climatització dels habitatges. El projecte es desenvolupa en l’àmbit domèstic, concretament correspon a un habitatge unifamiliar. Aquest està situat a la població de Roda de Ter, província de Barcelona. L’objectiu principal del projecte és l’elecció del sistema de climatització i el seu dimensionament, per tal de donar el màxim confort als usuaris que habitin a la vivenda. Criteris ambientals i eficients han estat objecte a considerar pel disseny constructiu de l’habitatge. Una de les mesures importants presses en el projecte, ha estat l’elecció de les diferents parts que formen la instal•lació de climatització. Es fa referència als aïllaments dels tancaments, el sistema solar de recolzament, equips de producció de fred i calor, entre d’altres. En el projecte, s’ha dut a terme un estudi dels diferents tancaments de l’habitatge, tot determinat per a cada un d’ells, el seu coeficient de transmissió tèrmica. Per seleccionar l’equipament més adequat s’ha partit de les condicions climatològiques del municipi de Roda de Ter i s’ha realitzat el càlcul de les necessitats tèrmiques de l’edifici. L’habitatge incorpora una instal•lació de captació solar tèrmica. Aquesta aportarà un suport energètic a tot el sistema de producció de calor, ja sigui per la producció d’aigua calenta sanitària com per el calefactat de la vivenda. La col•locació dels panells a la façana sud tindrà una doble funció: a més de proporcionar energia solar tèrmica, serviran d’elements de protecció solar en la temporada d’estiu. La caldera usada per donar recolzament tèrmic utilitzarà com a combustible el “pellet”. El “pellet” és un tipus de biomassa llenyosa que consta d’un derivat de la fusta en format granulat. Es defineix i es detalla el consum energètic en biomassa, electricitat i cost econòmic anual que ocasionarà la instal.lació dissenyada. El sistema de terra radiant adoptat permetrà el refrescament en èpoques estivals i el calefactat en èpoques hivernals. Aquest donarà el confort tèrmic necessari a cada estança de l’habitatge. En el projecte també es marquen les pautes bàsiques pel control de la instal•lació solar així com el control dels grups de bombament i la mescla d’aigua del terra radiant.

Optimizing of intelligence level in welding

The productivity, quality and cost efficiency of welding work are critical for metal industry today. Welding processes must get more effective and this can be done by mechanization and automation. Those systems are always expensive and they have to pay the investment back. In this case it is really important to optimize the needed intelligence and this way needed automation level, so that a company will get the best profit. This intelligence and automation level was earlier classified in several different ways which are not useful for optimizing the process of automation or mechanization of welding. In this study the intelligence of a welding system is defined in a new way to enable the welding system to produce a weld good enough. In this study a new way is developed to classify and select the internal intelligence level of a welding system needed to produce the weld efficiently. This classification contains the possible need of human work and its effect to the weld and its quality but does not exclude any different welding processes or methods. In this study a totally new way is developed to calculate the best optimization for the needed intelligence level in welding. The target of this optimization is the best possible productivity and quality and still an economically optimized solution for several different cases. This new optimizing method is based on grounds of product type, economical productivity, the batch size of products, quality and criteria of usage. Intelligence classification and optimization were never earlier made by grounds of a made product. Now it is possible to find the best type of welding system needed to welddifferent types of products. This calculation process is a universal way for optimizing needed automation or mechanization level when improving productivity of welding. This study helps the industry to improve productivity, quality and cost efficiency of welding workshops.

Oceanografia e Química: unindo conhecimentos em prol dos oceanos e da sociedade

The marine environment is certainly one of the most complex systems to study, not only because of the challenges posed by the nature of the waters, but especially due to the interactions of physical, chemical and biological processes that control the cycles of the elements. Together with analytical chemists, oceanographers have been making a great effort in the advancement of knowledge of the distribution patterns of trace elements and processes that determine their biogeochemical cycles and influences on the climate of the planet. The international academic community is now in prime position to perform the first study on a global scale for observation of trace elements and their isotopes in the marine environment (GEOTRACES) and to evaluate the effects of major global changes associated with the influences of megacities distributed around the globe. This action can only be performed due to the development of highly sensitive detection methods and the use of clean sampling and handling techniques, together with a joint international program working toward the clear objective of expanding the frontiers of the biogeochemistry of the oceans and related topics, including climate change issues and ocean acidification associated with alterations in the carbon cycle. It is expected that the oceanographic data produced this coming decade will allow a better understanding of biogeochemical cycles, and especially the assessment of changes in trace elements and contaminants in the oceans due to anthropogenic influences, as well as its effects on ecosystems and climate. Computational models are to be constructed to simulate the conditions and processes of the modern oceans and to allow predictions. The environmental changes arising from human activity since the 18th century (also called the Anthropocene) have made the Earth System even more complex. Anthropogenic activities have altered both terrestrial and marine ecosystems, and the legacy of these impacts in the oceans include: a) pollution of the marine environment by solid waste, including plastics; b) pollution by chemical and medical (including those for veterinary use) substances such as hormones, antibiotics, legal and illegal drugs, leading to possible endocrine disruption of marine organisms; and c) ocean acidification, the collateral effect of anthropogenic emissions of CO2 into the atmosphere, irreversible in the human life time scale. Unfortunately, the anthropogenic alteration of the hydrosphere due to inputs of plastics, metal, hydrocarbons, contaminants of emerging concern and even with formerly "exotic" trace elements, such us rare earth elements is likely to accelerate in the near future. These emerging contaminants would likely soon present difficulties for studies in pristine environments. All this knowledge brings with it a great responsibility: helping to envisage viable adaptation and mitigation solutions to the problems identified. The greatest challenge faced by Brazil is currently to create a framework project to develop education, science and technology applied to oceanography and related areas. This framework would strengthen the present working groups and enhance capacity building, allowing a broader Brazilian participation in joint international actions and scientific programs. Recently, the establishment of the National Institutes of Science and Technology (INCTs) for marine science, and the creation of the National Institute of Oceanographic and Hydrological Research represent an exemplary start. However, the participation of the Brazilian academic community in the latest assaults on the frontier of chemical oceanography is extremely limited, largely due to: i. absence of physical infrastructure for the preparation and processing of field samples at ultra-trace level; ii. limited access to oceanographic cruises, due to the small number of Brazilian vessels and/or absence of "clean" laboratories on board; iii. restricted international cooperation; iv. limited analytical capacity of Brazilian institutions for the analysis of trace elements in seawater; v. high cost of ultrapure reagents associated with processing a large number of samples, and vi. lack of qualified technical staff. Advances in knowledge, analytic capabilities and the increasing availability of analytical resources available today offer favorable conditions for chemical oceanography to grow. The Brazilian academic community is maturing and willing to play a role in strengthening the marine science research programs by connecting them with educational and technological initiatives in order to preserve the oceans and to promote the development of society.

LOW COST ANALYZER FOR THE DETERMINATION OF PHOSPHORUS BASED ON OPEN-SOURCE HARDWARE AND PULSED FLOWS

The need for automated analyzers for industrial and environmental samples has triggered the research for new and cost-effective strategies of automation and control of analytical systems. The widespread availability of open-source hardware together with novel analytical methods based on pulsed flows have opened the possibility of implementing standalone automated analytical systems at low cost. Among the areas that can benefit from this approach are the analysis of industrial products and effluents and environmental analysis. In this work, a multi-pumping flow system is proposed for the determination of phosphorus in effluents and polluted water samples. The system employs photometric detection based on the formation of molybdovanadophosphoric acid, and the fluidic circuit is built using three solenoid micropumps. The detection is implemented with a low cost LED-photodiode photometric detection system and the whole system is controlled by an open-source Arduino Uno microcontroller board. The optimization of the timing to ensure the color development and the pumping cycle is discussed for the proposed implementation. Experimental results to evaluate the system behavior are presented verifying a linear relationship between the relative absorbance and the phosphorus concentrations for levels as high as 50 mg L-1.

Analysis of electricity distribution network operation business models and capitalization of control room functions with DMS

Electricity distribution network operation (NO) models are challenged as they are expected to continue to undergo changes during the coming decades in the fairly developed and regulated Nordic electricity market. Network asset managers are to adapt to competitive technoeconomical business models regarding the operation of increasingly intelligent distribution networks. Factors driving the changes for new business models within network operation include: increased investments in distributed automation (DA), regulative frameworks for annual profit limits and quality through outage cost, increasing end-customer demands, climatic changes and increasing use of data system tools, such as Distribution Management System (DMS). The doctoral thesis addresses the questions a) whether there exist conditions and qualifications for competitive markets within electricity distribution network operation and b) if so, identification of limitations and required business mechanisms. This doctoral thesis aims to provide an analytical business framework, primarily for electric utilities, for evaluation and development purposes of dedicated network operation models to meet future market dynamics within network operation. In the thesis, the generic build-up of a business model has been addressed through the use of the strategicbusiness hierarchy levels of mission, vision and strategy for definition of the strategic direction of the business followed by the planning, management and process execution levels of enterprisestrategy execution. Research questions within electricity distribution network operation are addressed at the specified hierarchy levels. The results of the research represent interdisciplinary findings in the areas of electrical engineering and production economics. The main scientific contributions include further development of the extended transaction cost economics (TCE) for government decisions within electricity networks and validation of the usability of the methodology for the electricity distribution industry. Moreover, DMS benefit evaluations in the thesis based on the outage cost calculations propose theoretical maximum benefits of DMS applications equalling roughly 25% of the annual outage costs and 10% of the respective operative costs in the case electric utility. Hence, the annual measurable theoretical benefits from the use of DMS applications are considerable. The theoretical results in the thesis are generally validated by surveys and questionnaires.

Management of crotalaria and pigeon pea for control of yam nematode diseases

Management of plant-parasitic nematodes with the use of nematicides has not been recommended for small farmers that grow yam in the Northeastern region of Brazil, due to its high cost and residue toxicity. The use of plants with antagonistic effect to nematodes and green manure which improves soil chemical, physical and biological characteristics can be a viable and low cost alternative to control parasitic nematodes. This work aimed to evaluate the effect of crotalaria (Crotalaria juncea) and pigeon pea (Cajanus cajan) plants on the control of yam nematodes. Three experiments were carried out. The first was conducted under in vitro conditions to evaluate the nematostatic and nematicide effect of extracts from fresh and dry matter of the above ground parts of crotalaria, pigeon pea, and the combination of both. The second experiment was carried out under greenhouse conditions to evaluate the effect of soil amendment with crotalaria, pigeon pea, and the combination of both in the infectivity of Scutellonema bradys, using tomato plants as the host plant. The third experiment was conducted under field conditions to evaluate the effect of crotalaria, pigeon pea, and the combination of both, cultivated between yam planting rows and incorporated to soil surface, on yam nematodes. The aqueous extract obtained form fresh matter of crotalaria had a nematicide effect of 100% for S. bradys. Extracts from dry matter of both crotalaria and pigeon pea did not have any nematicide effect, but had a nematostatic effect. Incorporation of crotalaria to soil inhibited infectivity of S. bradys in tomato seedlings. These results showed that planting crotalaria alone or in combination with pigeon pea, between the yam planting rows, is an efficient method for controlling S. bradys and Rotylenchulus reniformis associated with yams. Crotalaria can be used for controlling these plant-parasitic nematodes in soil.

Physiological cost of induced resistance in cotton plants at different nitrogen levels

Resistance induction through the use of chemical inducers often results in physiological costs to the plant. In this study, induced resistance in cotton plants was evaluated with regard to physiological costs in a cultivar susceptible to Colletotrichum gossypii var. cephalosporioides (CNPA GO 2002 - 7997). Plants were cultivated in substrates with two levels of nitrogen and received two applications of acibenzolar-S-methyl (ASM), jasmonic acid (JA) and Agro-Mos® (AM) disease resistance inducers. Plant height (H), internodal length (IL), shoot fresh weight (SFW), root fresh weight (RFW), shoot dry weight (SDW) and root dry weight (RDW) were evaluated. The activity of the phenylalanine ammonia lyase (PAL) and peroxidase (POX) was also determined. The plants treated with ASM presented high physiological costs with an accentuated reduction in H, SFW and SDW, whereas those treated with JA exhibited a significant increase in SDW, and did not significantly differ from H and IL. In the potting mix supplemented with nitrogen, all inducers differed from the control treatment regarding to internodal length, whereas only ASM and AM presented a significant difference between one another in the potting mix without the addition of nitrogen. Significant correlations (P=0.05) were found for most of the variables analyzed, with greater correlations observed between SFW and SDW (0.94); IL and H (0.74); SFW and H (0.70); and SDW and H (0.70). ASM induced the least amount of PAL activity, significantly differing from the remaining treatments. Greater POX activity was observed in ASM, which significantly differed from the control. AM and JA, however, presented lower activity than the control with regard to these enzymes, and it was not possible to confirm induction resistance in these two treatments.

Automated, adaptive methods for forest inventory

Forest inventories are used to estimate forest characteristics and the condition of forest for many different applications: operational tree logging for forest industry, forest health state estimation, carbon balance estimation, land-cover and land use analysis in order to avoid forest degradation etc. Recent inventory methods are strongly based on remote sensing data combined with field sample measurements, which are used to define estimates covering the whole area of interest. Remote sensing data from satellites, aerial photographs or aerial laser scannings are used, depending on the scale of inventory. To be applicable in operational use, forest inventory methods need to be easily adjusted to local conditions of the study area at hand. All the data handling and parameter tuning should be objective and automated as much as possible. The methods also need to be robust when applied to different forest types. Since there generally are no extensive direct physical models connecting the remote sensing data from different sources to the forest parameters that are estimated, mathematical estimation models are of "black-box" type, connecting the independent auxiliary data to dependent response data with linear or nonlinear arbitrary models. To avoid redundant complexity and over-fitting of the model, which is based on up to hundreds of possibly collinear variables extracted from the auxiliary data, variable selection is needed. To connect the auxiliary data to the inventory parameters that are estimated, field work must be performed. In larger study areas with dense forests, field work is expensive, and should therefore be minimized. To get cost-efficient inventories, field work could partly be replaced with information from formerly measured sites, databases. The work in this thesis is devoted to the development of automated, adaptive computation methods for aerial forest inventory. The mathematical model parameter definition steps are automated, and the cost-efficiency is improved by setting up a procedure that utilizes databases in the estimation of new area characteristics.

Yritysvastuu ympäristönäkökulmasta

Diplomityön tavoitteena on selvittää yritysvastuun sisältöä ja merkitystä yritysten toiminnassa. Vastuullinen yritystoiminta sisältää taloudellisen, sosiaalisen ja ympäristön näkökulman. Ne ovat yksi edellytys yrityksen toiminnan jatkuvuudelle ja menestykselle. Työssä keskitytään erityisesti yritysvastuun ympäristönäkökulmaan, sillä ympäristöasiat ovat yhä enemmän esillä. Huoli ympäristön tilasta on lisääntynyt selvästi ja myös kuluttajat vaativat yrityksiltä vastuullista toimintaa. Lisäksi ympäristöön liittyvä lainsäädäntö kiristyy ja säädökset lisääntyvät. Kestävän kehityksen mukainen toiminta säästää luonnonvaroja ja vähentää ympäristön saastumista. Ympäristöasiat on huomioitava yrityksen kaikessa toiminnassa. Vihreässä taloudessa ympäristölle aiheutuu mahdollisimman vähän haittaa. Yrityksillä on merkittävä asema vihreän talouden kehittämisessä, sillä yritykset voivat vähentää toiminnasta aiheutuvia ympäristövaikutuksia, tuottaa ympäristöä säästäviä tuotteita sekä tarjota ratkaisuja ympäristövaikutusten pienentämiseen. Uuden teknologian kehittäminen on kestävän kehityksen kannalta oleellista ja siten voidaan myös saavuttaa kilpailuetua. Yritysten ympäristövastuullista toimintaa tukevat ympäristöpolitiikka ja –strategia, ympäristöjohtaminen, ympäristöjärjestelmät, ympäristöriskianalyysit, ympäristölaskenta sekä ympäristönmyötäinen tuotesuunnittelu. Nämä ovat työkaluja, jotka selventävät yritysten ympäristöön liittyviä tavoitteita ja päämääriä. Niitä voidaan hyödyntää päätöksenteon tukena ja ympäristöasioiden kehittämisessä. Ympäristökysymykset on myös tärkeää saada yhdistetyksi yritysten taloudelliseen ohjaukseen ja tuotesuunnitteluun. Työn perusteella voidaan todeta, että vastuullinen toiminta on merkittävä osa yritysten kilpailukykyä ja se on tärkeää yrityksen tulevaisuuden kannalta. Vastuullisuus on ehdottomasti yksi edellytys yritysten toiminnan jatkuvuudelle. Vastuullinen toiminta edistää yrityksen kilpailukykyä ja sen avulla voidaan saavuttaa myös uusia asiakkaita ja markkina-alueita. Ympäristöystävällisempien tuotteiden kehittäminen, jätteen määrän vähentäminen ja prosessien tehostaminen tuovat yrityksille kustannussäästöjä. Vastuullinen toiminta lisää yritysten innovatiivisuutta ja uusien liiketoimintamallien syntymistä. Kuluttajavalinnoissa painottuvat enemmän myös ympäristöön ja yhteiskuntaan liittyvät arvot, joten vastuullisuus voi lisätä kysyntää ja asiakkaiden määrää. Myös rahoittajat ja uudet työntekijät ovat kiinnostuneita vastuullisista yrityksistä. Vastuullinen yritys nähdään houkuttelevana ja luotettavana yhteistyökumppanina.

Tabular cusum control charts of chemical variables applied to the control of surface water quality

The aim of this study was to evaluate the application possibility of tabular CUSUM control charts in the quality control of chemical variables in surface water. It was performed bibliographic and field research to collect water samples from 2003 to 2009, totaling 30 samples, some monthly and others semi-annual in order to observe the variables that regulate water quality. It was found that these charts may be applied to control the quality of river water; showing to be effective in the perception of changes during the process, especially for small samples (n=1) which there is no repetition as in this research. It was also concluded that the Mandurim River does not presents significant levels of pollution.

Low cost driver device for microclimate maintenance in the pre-milking of dairy cattle

Due to the importance of the environment on animal production and thus environmental control, the study aims to build a system for monitoring and control the meteorological variables, temperature and relative humidity, low cost, which can be associated with an evaporative cooling system (ECS). The system development included all the stages of assembly, test and laboratory calibration, and later the validation of the equipment carried in the field. The validation step showed results which allowed concluding that the system can be safely used in the monitoring of these variables. The controller was efficient in management of the microclimate in the waiting corral and allowed the maintenance of the air temperature within the comfort range for dairy cattle in pre-milking with averaged 25.09 ºC during the afternoon. The equipment showed the lower cost (R$ 325.76) when compared to other middle market (R$ 450.00).

Development of a project control procedure

The aim of this study is to develop a suitable project control procedure for a target company that can be used in engineering, procurement, and construction or con-struction management contracts. This procedure contains suitable project control software and a model for the use of the software in practice. This study is divided into two main sections. Theoretical part deals with project management, focusing on cost and time dimensions in projects. Empirical part deals with the development of the project control procedure for the target compa-ny. This development takes place in two parts. In the first part, semi-structured interviews are used to find out the company’s employees’ demands and desires for the project control software which will then be used in the developed procedure. These demands and desires are compared to available software in the market and the most suitable one will be chosen. Interview results show that important factors are cost tracking, integration with other software, English language availability, references, helpdesk, and no need for regular updates. The most suitable one is CMPro5 cost control software. The chosen software is used in a pilot project, where its functions and use are analyzed. Project control procedure which will be used in the future is developed based on these procedures. The five steps in developed procedure include employment of a cost engineer, whose task is to maintain the procedure in the target company.