Kinematics of the Sicily and Calabria Subduction System from Elastic Block Modeling of GPS Data

We use data from about 700 GPS stations in the EuroMediterranen region to investigate the present-day behavior of the the Calabrian subduction zone within the Mediterranean-scale plates kinematics and to perform local scale studies about the strain accumulation on active structures. We focus attenction on the Messina Straits and Crati Valley faults where GPS data show extentional velocity gradients of ∼3 mm/yr and ∼2 mm/yr, respectively. We use dislocation model and a non-linear constrained optimization algorithm to invert for fault geometric parameters and slip-rates and evaluate the associated uncertainties adopting a bootstrap approach. Our analysis suggest the presence of two partially locked normal faults. To investigate the impact of elastic strain contributes from other nearby active faults onto the observed velocity gradient we use a block modeling approach. Our models show that the inferred slip-rates on the two analyzed structures are strongly impacted by the assumed locking width of the Calabrian subduction thrust. In order to frame the observed local deformation features within the present- day central Mediterranean kinematics we realyze a statistical analysis testing the indipendent motion (w.r.t. the African and Eurasias plates) of the Adriatic, Cal- abrian and Sicilian blocks. Our preferred model confirms a microplate like behaviour for all the investigated blocks. Within these kinematic boundary conditions we fur- ther investigate the Calabrian Slab interface geometry using a combined approach of block modeling and χ2ν statistic. Almost no information is obtained using only the horizontal GPS velocities that prove to be a not sufficient dataset for a multi-parametric inversion approach. Trying to stronger constrain the slab geometry we estimate the predicted vertical velocities performing suites of forward models of elastic dislocations varying the fault locking depth. Comparison with the observed field suggest a maximum resolved locking depth of 25 km.

Reliable and Variation-Tolerant Interconnection Network for Low Power MPSOCS

Multi-Processor SoC (MPSOC) design brings to the foreground a large number of challenges, one of the most prominent of which is the design of the chip interconnection. With a number of on-chip blocks presently ranging in the tens, and quickly approaching the hundreds, the novel issue of how to best provide on-chip communication resources is clearly felt. Scaling down of process technologies has increased process and dynamic variations as well as transistor wearout. Because of this, delay variations increase and impact the performance of the MPSoCs. The interconnect architecture inMPSoCs becomes a single point of failure as it connects all other components of the system together. A faulty processing element may be shut down entirely, but the interconnect architecture must be able to tolerate partial failure and variations and operate with performance, power or latency overhead. This dissertation focuses on techniques at different levels of abstraction to face with the reliability and variability issues in on-chip interconnection networks. By showing the test results of a GALS NoC testchip this dissertation motivates the need for techniques to detect and work around manufacturing faults and process variations in MPSoCs’ interconnection infrastructure. As a physical design technique, we propose the bundle routing framework as an effective way to route the Network on Chips’ global links. For architecture-level design, two cases are addressed: (I) Intra-cluster communication where we propose a low-latency interconnect with variability robustness (ii) Inter-cluster communication where an online functional testing with a reliable NoC configuration are proposed. We also propose dualVdd as an orthogonal way of compensating variability at the post-fabrication stage. This is an alternative strategy with respect to the design techniques, since it enforces the compensation at post silicon stage.

Palynologie und Sedimentologie der Interglazialprofile Döttingen, Bonstorf, Munster und Bilshausen

Palynologie und Sedimentologie der Interglazialprofile Döttingen, Bonstorf, Munster und Bilshausen Zusammenfassung In der vorliegenden Dissertation wurden vier dem Holstein-Interglazial zugehörige Bohrkerne sowie ein rhumezeitlicher Bohrkern palynologisch und sedimentologisch bearbeitet. Die holsteinzeitlichen Bohrkerne stammen aus Kieselgurlagerstätten der Lüneburger Heide (Bonstorf und Munster) und aus einem Trockenmaar (Döttingen) in der Eifel. Der rhumezeitliche Kern stammt aus der Typlokalität Bilshausen im Harzvorland. Neben Prozentwertdiagrammen werden Pollendichte- und wenn möglich Polleninfluxwerte vorgestellt, die insbesondere für die Lokalitäten Hetendorf/Bonstorf und Munster/Breloh bisher nicht verfügbar waren. Mit dem Profil Döttingen konnte erstmals eine sowohl vollständige als auch nicht innerhalb des klassischen Aufkommens holsteinzeitlicher Fundstellen im norddeutschen Tiefland positionierte Holsteinsequenz aus dem deutschen Mittelgebirge dokumentiert werden. Das erhaltene Pollendiagramm bestätigt die aus den norddeutschen Profilen bekannte holsteintypische Vegetationsabfolge, durch die das Holstein gegenüber anderen Interglazialen wie Holozän, Eem oder Rhume palynologisch definiert ist. Neben der grundsätzlichen Übereinstimmung der Pollensequenz unterscheidet sich das Profil Döttingen aber deutlich im prozentualen Aufkommen der beteiligten Taxa von den norddeutschen Profilen. So wird eine hohe Alnus-Präsenz als Merkmal deutscher Holsteinprofile bestätigt, jedoch ist die, in den norddeutschen Lokalitäten durchhaltend hohe oder dominante Beteiligung von Pinus im deutschen Mittelgebirge nicht vorhanden und muss daher auf die Standortbedingungen Norddeutschlands zurückgeführt werden. Abies dagegen ist im Holstein der Mittelgebirge wesentlich präsenter als im norddeutschen Flachland. Im Profil Döttingen wurden insgesamt 10 Tephralagen gefunden. Auf eine dieser Tephren folgt ein „Birken-Kiefern-Gräser Vorstoß“, der palynostratigraphisch dem älteren „Birken-Kiefern Vorstoß“ in Munster/Breloh entspricht. Als eine Typologie des Holstein kann das in den Profilen Döttingen und Munster bestätigte intraholsteinzeitliche Carpinus-Minimum verstanden werden. An Hand sedimentologischer und palynologischer Befunde aus dem Bohrkern MU 2 muss die Existenz zweier, in der Literatur postulierter, postholsteinzeitlicher, „Nachschwankungen“ in Munster/Breloh in Frage gestellt, wenn nicht abgelehnt werden. In Kern MU 2 fallen palynostratigraphische Grenzen häufig mit Sandeinschaltungen zusammen. Eine dieser Sandeinschaltungen, nämlich unmittelbar vor dem älteren „Birken-Kiefern-Vorstoß“, korreliert in ihrer stratigraphischen Position mit der den „Birken-Kiefern-Gräser-Vorstoß“ im Profil Döttingen einleitenden Tephralage. Es gelang die Dauer des intraholsteinzeitlichen Carpinus Minimums auf etwa 1500±100 Jahre zu bestimmen und eine interne Zweigliederung zu dokumentieren. Im rhumezeitlichen Kern von Bilshausen (BI 1) konnten zahlreiche Störungen nachgewiesen werden. Insbesondere im Teufenbereich des Bilshausener „Birken-Kiefern-Vorstoßes“ deuten diese auf eine möglicherweise verfälschte Überlieferung. Der palynologisch markante „Lindenfall“ von Bilshausen liegt im Bereich einer isoklinalen Schichtenverfaltung. Die in der Literatur im Horizont des „Lindenfalls“ beschriebene „Bilshausentephra“ wurde nicht gefunden. Warvenzählungen an den Kernen MU 1, MU 2 und BI 1 ermöglichten Pollenzonendauern in Holstein- und Rhume-Interglazial zu bestimmen. Dabei wurde mittels den Warvenzählungen, unter zu Hilfenahme von Literaturdaten und von Schätzwerten eine Dauer für das Holstein-Interglazial sensu stricto (Pollenzonen I-XIV) von 15400-17800 Jahren und für das Rhume-Interglazial von wahrscheinlich 22000 Jahren bis maximal 26000 Jahren ermittelt.

Evoluzione Morfotettonica delle Aree Alpine "Sempione" e "Brennero" attraverso Studi Termocronologici di bassa temperatura

E’ mostrata l’analisi e la modellazione di dati termocronologici di bassa temperatura da due regioni Alpine: il Sempione ed il Brennero. Le faglie distensive presenti bordano settori crostali profondi appartenenti al dominio penninico: il duomo metamorfico Lepontino al Sempione e la finestra dei Tauri al Brennero. I dati utilizzati sono FT e (U-Th)/He su apatite. Per il Sempione i dati provengono dalla bibliografia; per il Brennero si è provveduto ad un nuovo campionamento, sia in superficie che in sotterraneo. Gli attuali lavori per la galleria di base del Brennero (BBT), hanno consentito, per la prima volta, di raccogliere dati di FT e (U-Th)/He in apatite in sottosuolo per la finestra dei Tauri occidentale. Le analisi sono state effettuate tramite un codice a elementi finiti, Pecube, risolvente l’equazione di diffusione del calore per una topografia evolvente nel tempo. Il codice è stato modificato per tener conto dei dati sotterranei. L’inversione dei dati è stata effettuata usando il Neighbourhood Algorithm (NA), per ottenere il più plausibile scenario di evoluzione morfotettonico. I risultati ottenuti per il Sempione mostrano: ipotetica evoluzione dello stile tettonico della faglia del Sempione da rolling hinge a low angle detachment a 6.5 Ma e la cessazione dell’attività a 3 Ma; costruzione del rilievo fino a 5.5 Ma, smantellamento da 5.5 Ma ad oggi, in coincidenza dei cambiamenti climatici Messiniani e relativi all’inizio delle maggiori glaciazioni; incremento dell’esumazione da 0–0.6 mm/anno a 0.6–1.2 mm/anno a 2.4 Ma nell’emisfero settentrionale. I risultati al Brennero mostrano: maggiore attività tettonica della faglia del Brennero (1.3 mm/anno), maggiore attività esumativa (1–2 mm/anno) prima dei 10 Ma; crollo dell’attività della faglia del Brennero fra 10 Ma e oggi (0.1 mm/anno) e dell’attività esumativa nello stesso periodo (0.1–0.3 mm/anno); nessun aumento del tasso esumativo o variazioni topografiche negli ultimi 5 Ma.

Structural and strain analysis in the Late Paleozoic coastal accretionary wedge of central Chile

Abstract In this study structural and finite strain data are used to explore the tectonic evolution and the exhumation history of the Chilean accretionary wedge. The Chilean accretionary wedge is part of a Late Paleozoic subduction complex that developed during subduction of the Pacific plate underneath South America. The wedge is commonly subdivided into a structurally lower Western Series and an upper Eastern Series. This study shows the progressive development of structures and finite strain from the least deformed rocks in the eastern part of the Eastern Series of the accretionary wedge to higher grade schist of the Western Series at the Pacific coast. Furthermore, this study reports finite-strain data to quantify the contribution of vertical ductile shortening to exhumation. Vertical ductile shortening is, together with erosion and normal faulting, a process that can aid the exhumation of high-pressure rocks. In the east, structures are characterized by upright chevron folds of sedimentary layering which are associated with a penetrative axial-plane foliation, S1. As the F1 folds became slightly overturned to the west, S1 was folded about recumbent open F2 folds and an S2 axial-plane foliation developed. Near the contact between the Western and Eastern Series S2 represents a prominent subhorizontal transposition foliation. Towards the structural deepest units in the west the transposition foliation became progressively flat lying. Finite-strain data as obtained by Rf/Phi and PDS analysis in metagreywacke and X-ray texture goniometry in phyllosilicate-rich rocks show a smooth and gradual increase in strain magnitude from east to west. There are no evidences for normal faulting or significant structural breaks across the contact of Eastern and Western Series. The progressive structural and strain evolution between both series can be interpreted to reflect a continuous change in the mode of accretion in the subduction wedge. Before ~320-290 Ma the rocks of the Eastern Series were frontally accreted to the Andean margin. Frontal accretion caused horizontal shortening and upright folds and axial-plane foliations developed. At ~320-290 Ma the mode of accretion changed and the rocks of the Western Series were underplated below the Andean margin. This basal accretion caused a major change in the flow field within the wedge and gave rise to vertical shortening and the development of the penetrative subhorizontal transposition foliation. To estimate the amount that vertical ductile shortening contributed to the exhumation of both units finite strain is measured. The tensor average of absolute finite strain yield Sx=1.24, Sy=0.82 and Sz=0.57 implying an average vertical shortening of ca. 43%, which was compensated by volume loss. The finite strain data of the PDS measurements allow to calculate an average volume loss of 41%. A mass balance approximates that most of the solved material stays in the wedge and is precipitated in quartz veins. The average of relative finite strain is Sx=1.65, Sy=0.89 and Sz=0.59 indicating greater vertical shortening in the structurally deeper units. A simple model which integrates velocity gradients along a vertical flow path with a steady-state wedge is used to estimate the contribution of deformation to ductile thinning of the overburden during exhumation. The results show that vertical ductile shortening contributed 15-20% to exhumation. As no large-scale normal faults have been mapped the remaining 80-85% of exhumation must be due to erosion.

Flash floods and their effects on the development in El-Qaá plain area in South Sinai, Egypt

The arid regions are dominated to a much larger degree than humid regions by major catastrophic events. Although most of Egypt lies within the great hot desert belt; it experiences especially in the north some torrential rainfall, which causes flash floods all over Sinai Peninsula. Flash floods in hot deserts are characterized by high velocity and low duration with a sharp discharge peak. Large sediment loads may be carried by floods threatening fields and settlements in the wadis and even people who are living there. The extreme spottiness of rare heavy rainfall, well known to desert people everywhere, precludes any efficient forecasting. Thus, although the limitation of data still reflects pre-satellite methods, chances of developing a warning system for floods in the desert seem remote. The relatively short flood-to-peak interval, a characteristic of desert floods, presents an additional impediment to the efficient use of warning systems. The present thesis contains introduction and five chapters, chapter one points out the physical settings of the study area. There are the geological settings such as outcrop lithology of the study area and the deposits. The alluvial deposits of Wadi Moreikh had been analyzed using OSL dating to know deposits and palaeoclimatic conditions. The chapter points out as well the stratigraphy and the structure geology containing main faults and folds. In addition, it manifests the pesent climate conditions such as temperature, humidity, wind and evaporation. Besides, it presents type of soils and natural vegetation cover of the study area using unsupervised classification for ETM+ images. Chapter two points out the morphometric analysis of the main basins and their drainage network in the study area. It is divided into three parts: The first part manifests the morphometric analysis of the drainage networks which had been extracted from two main sources, topographic maps and DEM images. Basins and drainage networks are considered as major influencing factors on the flash floods; Most of elements were studied which affect the network such as stream order, bifurcation ratio, stream lengths, stream frequency, drainage density, and drainage patterns. The second part of this chapter shows the morphometric analysis of basins such as area, dimensions, shape and surface. Whereas, the third part points the morphometric analysis of alluvial fans which form most of El-Qaá plain. Chapter three manifests the surface runoff through rainfall and losses analysis. The main subject in this chapter is rainfall which has been studied in detail; it is the main reason for runoff. Therefore, all rainfall characteristics are regarded here such as rainfall types, distribution, rainfall intensity, duration, frequency, and the relationship between rainfall and runoff. While the second part of this chapter concerns with water losses estimation by evaporation and infiltration which are together the main losses with direct effect on the high of runoff. Finally, chapter three points out the factors influencing desert runoff and runoff generation mechanism. Chapter four is concerned with assessment of flood hazard, it is important to estimate runoff and tocreate a map of affected areas. Therefore, the chapter consists of four main parts; first part manifests the runoff estimation, the different methods to estimate runoff and its variables such as runoff coefficient lag time, time of concentration, runoff volume, and frequency analysis of flash flood. While the second part points out the extreme event analysis. The third part shows the map of affected areas for every basin and the flash floods degrees. In this point, it has been depending on the DEM to extract the drainage networks and to determine the main streams which are normally more dangerous than others. Finally, part four presets the risk zone map of total study area which is of high inerest for planning activities. Chapter five as the last chapter concerns with flash flood Hazard mitigation. It consists of three main parts. First flood prediction and the method which can be used to predict and forecast the flood. The second part aims to determine the best methods which can be helpful to mitigate flood hazard in the arid zone and especially the study area. Whereas, the third part points out the development perspective for the study area indicating the suitable places in El-Qaá plain for using in economic activities.

The Influence of Fractures on Vulnerability to Pollution of a Carbonate Aquifer: Monte Conero (Italy)

The carbonate outcrops of the anticline of Monte Conero (Italy) were studied in order to characterize the geometry of the fractures and to establish their influence on the petrophysical properties (hydraulic conductivity) and on the vulnerability to pollution. The outcrops form an analog for a fractured aquifer and belong to the Maiolica Fm. and the Scaglia Rossa Fm. The geometrical properties of fractures such as orientation, length, spacing and aperture were collected and statistically analyzed. Five types of mechanical fractures were observed: veins, joints, stylolites, breccias and faults. The types of fractures are arranged in different sets and geometric assemblages which form fracture networks. In addition, the fractures were analyzed at the microscale using thin sections. The fracture age-relationships resulted similar to those observed at the outcrop scale, indicating that at least three geological episodes have occurred in Monte Conero. A conceptual model for fault development was based on the observations of veins and stylolites. The fracture sets were modelled by the code FracSim3D to generate fracture network models. The permeability of a breccia zone was estimated at microscale by and point counting and binary image methods, whereas at the outcrop scale with Oda’s method. Microstructure analysis revealed that only faults and breccias are potential pathways for fluid flow since all veins observed are filled with calcite. According this, three scenarios were designed to asses the vulnerability to pollution of the analogue aquifer: the first scenario considers the Monte Conero without fractures, second scenario with all observed systematic fractures and the third scenario with open veins, joints and faults/breccias. The fractures influence the carbonate aquifer by increasing its porosity and hydraulic conductivity. The vulnerability to pollution depends also on the presence of karst zones, detric zones and the material of the vadose zone.

I doveri e le responsabilità contabili nella corporate governance delle società di capitali

La costruzione di un modello efficiente di corporate governance deve offrire una disciplina adeguata dei doveri contabili. Ciò nonostante, gli ordinamenti giuridici configurano i doveri di contabilità in modo incompleto, giacché l’inadempimento di questi non comporta una sanzione diretta per il soggetto inadempiente. Come informazione sulla situazione economica e finanziaria della società, esiste un interesse pubblico nella contabilità, e questa può servire come base di giudizio a soggetti interni ed esterni all’impresa, nell’adozione delle sue scelte. Disporre di un’informazione falsa o inesatta al riguardo può comportare un danno ingiustificato alla società stessa, ai soci o ai terzi, che potranno esercitare le azioni precise per il risarcimento del danno cagionato. Per evitare la produzione di questi danni, da una prospettiva preventiva, la corporate governance delle società di capitali può prevedere dei meccanismi di controllo che riducano il rischio di offrire un’informazione sbagliata. Questi controlli potranno essere esercitati da soggetti interni o esterni (revisori legali) alla struttura della società, ed avranno una configurazione diversa a seconda che le società adottino una struttura monistica o dualistica di governance. Questo ci colloca di fronte ad una eventuale situazione di concorrenza delle colpe, giacché i diversi soggetti che intervengono nel processo d’elaborazione dell’informazione contabile versano la sua attuazione sullo stesso documento: il bilancio. Risulta dunque cruciale determinare il contributo effettivo di ciascuno per analizzare il suo grado di responsabilità nella produzione del danno.

Entwicklung und Anwendung molekularbiologischer Methoden zur Art- und Stamm-Identifizierung pro- und eukaryotischer Organismen

Das Wachstum von Milchsäurebakterien-Arten der Gattungen Lactobacillus, Pediococcus und Leuconostoc während der Weinfermentation kann durch die Bildung verschiedener Stoffwechselprodukte zu Weinfehlern führen. Um rechtzeitig Gegenmaßnahmen ergreifen zu können und einem Weinverderb vorzubeugen, bedarf es geeigneter Identifizierungsmethoden. Klassische mikrobiologische Methoden reichen oft nicht aus, um Mikroorganismen auf Art- und Stammniveau gezielt zu identifizieren. Wegen ihrer schnellen Durchführbarkeit und Zuverlässigkeit sind molekularbiologische Identifizierungsmethoden zur Kontrolle der mikrobiellen Flora während der Lebensmittelfermentierung in der heutigen Zeit unabdingbar. In der vorliegenden Forschungsarbeit wurden die 23S rRNA-Gensequenzen von neun Pediococcus-Typstämmen sequenziert, analysiert und phylogenetische Analysen durchgeführt. Zur Art-Identifizierung der Pediokokken wurden PCR-Primer generiert und ein Multiplex PCR System entwickelt, mit dem alle typischen Arten simultan in einer Reaktion nachgewiesen werden konnten. Die Ergebnisse der Multiplex PCR-Identifizierung von 62 Pediococcus-Stämmen aus Kulturensammlungen und 47 neu isolierten Stämmen aus Wein zeigten, dass einige Stämme unter falschen Artnamen hinterlegt waren, und dass P. parvulus im Weinanbaugebiet Rheinhessen weit verbreitet war. Die Fähigkeit der Pediococcus-Stämme zur Exopolysaccharid-Synthese wurde durch den Nachweis zweier Gene überprüft. Auf Basis der 23S rDNA-Sequenzen wurden rRNA-Sekundärstrukturen mit der neu entwickelten Software Structure Star generiert, die zum Auffinden von Zielbereichen für fluoreszenzmarkierte DNA-Sonden geeignet waren. Die Sequenzunterschiede zwischen den Pediococcus-Arten reichten aus, um zwei Gruppen durch Fluoreszenz in situ Hybridisierung differenzieren zu können. Die Verwendung unmarkierter Helfer-sonden verbesserte die Zugänglichkeit der Sonden an die rRNA, wodurch das Fluoreszenz-Signal verstärkt wurde. Um Milchsäurebakterien durch Denaturierende Gradienten Gel Elektrophorese differenzieren zu können, wurden Primer entwickelt, mit denen ein hochvariabler 23S rDNA-Bereich amplifiziert werden konnte. Die Nested Specifically Amplified Polymorphic DNA (nSAPD)-PCR wurde in der vorliegenden Arbeit zur Art- und Stamm-Differenzierung pro- und eukaryotischer Organismen angewandt. Es wurden vor allem weinrelevante Milchsäurebakterien der Gattungen Oenococcus, Lactobacillus, Pediococcus und Leuconostoc und Hefen der Gattungen Dekkera / Brettanomyces und Saccharomyces untersucht. Die Cluster-Analyse der Pediococcus-Typstämme führte zu einer unterschiedlichen Baum-Topologie im Vergleich zum phylogenetischen 23S rDNA-Stammbaum. Die Verwandtschaftsverhältnisse der untersuchten O. oeni-Stämme aus Starterkulturen konnten in Bezug auf eine frühere Cluster-Analyse reproduziert werden. Die Untersuchung von 40 B. bruxellensis-Stämmen aus rheinhessischen Weinproben zeigte eine Gruppierung der Stämme gemäß dem Ort der Probennahme. Beim Vergleich der Verwandtschaftsverhältnisse von Stämmen der Arten P. parvulus und B. bruxellensis, die aus denselben Weinproben isoliert wurden, konnte eine hohe Übereinstimmung der beiden Baum-Topologien beobachtet werden. Anhand der SAPD-PCR Untersuchung von Sekthefen aus Starterkulturen konnten alle Stämme der Art S. cerevisiae zugeordnet werden. Die nSAPD-PCR war darüber hinaus geeignet, um höhere Eukaryoten wie Weinreben zu differenzieren und es konnten die Verwandtschaftsverhältnisse von Mäusen und menschlichen Individuen durch Cluster-Analysen nachvollzogen werden. Mit Hilfe der Sequence Characterized Amplified Region (SCAR)-Technik wurden (n)SAPD-Marker in SCAR-Marker konvertiert. Die neu generierten SCAR-Primer konnten zur simultanen Art-Identifizierung von sieben weinschädlichen Milchsäurebakterien in einer Multiplex PCR erfolgreich eingesetzt werden. Die in dieser Arbeit entwickelten molekularbiologischen Identifizierungsmethoden können zum Beispiel in der mikrobiologischen Qualitätskontrolle Anwendung finden.

Modelling and Design of Advanced Reliable Circuits and Devices for Energy Efficiency

Reliable electronic systems, namely a set of reliable electronic devices connected to each other and working correctly together for the same functionality, represent an essential ingredient for the large-scale commercial implementation of any technological advancement. Microelectronics technologies and new powerful integrated circuits provide noticeable improvements in performance and cost-effectiveness, and allow introducing electronic systems in increasingly diversified contexts. On the other hand, opening of new fields of application leads to new, unexplored reliability issues. The development of semiconductor device and electrical models (such as the well known SPICE models) able to describe the electrical behavior of devices and circuits, is a useful means to simulate and analyze the functionality of new electronic architectures and new technologies. Moreover, it represents an effective way to point out the reliability issues due to the employment of advanced electronic systems in new application contexts. In this thesis modeling and design of both advanced reliable circuits for general-purpose applications and devices for energy efficiency are considered. More in details, the following activities have been carried out: first, reliability issues in terms of security of standard communication protocols in wireless sensor networks are discussed. A new communication protocol is introduced, allows increasing the network security. Second, a novel scheme for the on-die measurement of either clock jitter or process parameter variations is proposed. The developed scheme can be used for an evaluation of both jitter and process parameter variations at low costs. Then, reliability issues in the field of “energy scavenging systems” have been analyzed. An accurate analysis and modeling of the effects of faults affecting circuit for energy harvesting from mechanical vibrations is performed. Finally, the problem of modeling the electrical and thermal behavior of photovoltaic (PV) cells under hot-spot condition is addressed with the development of an electrical and thermal model.

Characterization of fold-related fractures in the carbonate rocks of the Cingoli anticline, northern Apennines, Italy

Thrust fault-related folds in carbonate rocks are characterized by deformation accommodated by different structures, such as joints, faults, pressure solution seams, and deformation bands. Defining the development of fracture systems related to the folding process is significant both for theoretical and practical purposes. Fracture systems are useful constrains in order to understand the kinematical evolution of the fold. Furthermore, understanding the relationships between folding and fracturing provides a noteworthy contribution for reconstructing the geodynamic and the structural evolution of the studied area. Moreover, as fold-related fractures influence fluid flow through rocks, fracture systems are relevant for energy production (geothermal studies, methane and CO2 , storage and hydrocarbon exploration), environmental and social issues (pollutant distribution, aquifer characterization). The PhD project shows results of a study carried out in a multilayer carbonate anticline characterized by different mechanical properties. The aim of this study is to understand the factors which influence the fracture formation and to define their temporal sequence during the folding process. The studied are is located in the Cingoli anticline (Northern Apennines), which is characterized by a pelagic multilayer characterized by sequences with different mechanical stratigraphies. A multi-scale analysis has been made in several outcrops located in different structural positions. This project shows that the conceptual sketches proposed in literature and the strain distribution models outline well the geometrical orientation of most of the set of fractures observed in the Cingoli anticline. On the other hand, the present work suggests the relevance of the mechanical stratigraphy in particular controlling the type of fractures formed (e.g. pressure solution seams, joints or shear fractures) and their subsequent evolution. Through a multi-scale analysis, and on the basis of the temporal relationship between fracture sets and their orientation respect layering, I also suggest a conceptual model for fracture systems formation.

Diagnosis and Fault detection in Electrical Machines and Drives based on Advanced Signal Processing Techniques

In the present thesis, a new methodology of diagnosis based on advanced use of time-frequency technique analysis is presented. More precisely, a new fault index that allows tracking individual fault components in a single frequency band is defined. More in detail, a frequency sliding is applied to the signals being analyzed (currents, voltages, vibration signals), so that each single fault frequency component is shifted into a prefixed single frequency band. Then, the discrete Wavelet Transform is applied to the resulting signal to extract the fault signature in the frequency band that has been chosen. Once the state of the machine has been qualitatively diagnosed, a quantitative evaluation of the fault degree is necessary. For this purpose, a fault index based on the energy calculation of approximation and/or detail signals resulting from wavelet decomposition has been introduced to quantify the fault extend. The main advantages of the developed new method over existing Diagnosis techniques are the following: - Capability of monitoring the fault evolution continuously over time under any transient operating condition; - Speed/slip measurement or estimation is not required; - Higher accuracy in filtering frequency components around the fundamental in case of rotor faults; - Reduction in the likelihood of false indications by avoiding confusion with other fault harmonics (the contribution of the most relevant fault frequency components under speed-varying conditions are clamped in a single frequency band); - Low memory requirement due to low sampling frequency; - Reduction in the latency of time processing (no requirement of repeated sampling operation).

Grid Connected Doubly Fed Induction Generator Based Wind Turbine under LVRT

This project concentrates on the Low Voltage Ride Through (LVRT) capability of Doubly Fed Induction Generator (DFIG) wind turbine. The main attention in the project is, therefore, drawn to the control of the DFIG wind turbine and of its power converter and to the ability to protect itself without disconnection during grid faults. It provides also an overview on the interaction between variable speed DFIG wind turbines and the power system subjected to disturbances, such as short circuit faults. The dynamic model of DFIG wind turbine includes models for both mechanical components as well as for all electrical components, controllers and for the protection device of DFIG necessary during grid faults. The viewpoint of this project is to carry out different simulations to provide insight and understanding of the grid fault impact on both DFIG wind turbines and on the power system itself. The dynamic behavior of DFIG wind turbines during grid faults is simulated and assessed by using a transmission power system generic model developed and delivered by Transmission System Operator in the power system simulation toolbox Digsilent, Matlab/Simulink and PLECS.

Nanoscale surface properties and interaction with fundamental biomolecules of chlorite and phlogopite

The surface properties of minerals have important implications in geology, environment, industry and biotechnology and for certain aspects in the research on the origin of life. This research project aims to widen the knowledge on the nanoscale surface properties of chlorite and phlogopite by means of advanced methodologies, and also to investigate the interaction of fundamental biomolecules, such as nucleotides, RNA, DNA and amino acid glycine with the surface of the selected phyllosilicates. Multiple advanced and complex experimental approaches based on scanning probe microscopy and spatially resolved spectroscopy were used and in some cases specifically developed. The results demonstrate that chlorite exposes at the surface atomically flat terraces with 0.5 nm steps typically generated by the fragmentation of the octahedral sheet of the interlayer (brucitic-type). This fragmentation at the nanoscale generates a high anisotropy and inhomogeneity with surface type and isomorphous cationic substitutions determining variations of the effective surface potential difference, ranging between 50-100 mV and 400-500 mV, when measured in air, between the TOT surface and the interlayer brucitic sheet. The surface potential was ascribed to be the driving force of the observed high affinity of the surface with the fundamental biomolecules, like single molecules of nucleotides, DNA, RNA and amino acids. Phlogopite was also observed to present an extended atomically flat surface, featuring negative surface potential values of some hundreds of millivolts and no significant local variations. Phlogopite surface was sometimes observed to present curvature features that may be ascribed to local substitutions of the interlayer cations or the presence of a crystal lattice mismatch or structural defects, such as stacking faults or dislocation loops. Surface chemistry was found similar to the bulk. The study of the interaction with nucleotides and glycine revealed a lower affinity with respect to the brucite-like surface of chlorite.

Late Quaternary geological evolution of the Montenegro and Northern Albania continental margins

The object of this work has been the analysis of natural processes controlling the geological evolution of the Montenegro and Northern Albania Continental Margin (MACM) during the Late Quaternary. These include the modern sediment dispersal system and oceanographic regime, the building and shaping of the shelf margin at the scale of 100 kyr and relative to the most recent transition between glacial and interglacial periods. The analysis of the new data shows that the MACM is a shelf-slope system formed by a suite of physiographic elements, including: an inner and an outer continental shelf, separated by two tectonically-controlled morphological highs; a lobated drowned mid-shelf paleodelta, formed during the last sea level fall and low stand; an upper continental slope, affected by gravity-driven instability and a system of extensional faults with surficial displacement, featuring an orientation coherent with the regional tectonics. The stratigraphic study of the MACM shows a clear correspondence between the Late Pleistocene/Holocene mud-wedge and the low reflectivity sectors of the inner shelf. Conversely, most of the outer shelf and part of the continental slope expose deposits from the last sea level low stand, featuring a general sediment starving condition or the presence of a thin postglacial sediments cover. The MACM shows uplift in correspondence of the Kotor and Bar ridges, and subsidence in the outer shelf and upper slope sectors. In fact, seaward of these tectonic ridges, the sparker seismic profile show the presence of four well-defined seismo-stratigraphic sequences, interpreted as forced regression deposits, formed during the last four main glacial phases. In this way, the MACM records the 100 kyr scale sea level fluctuations on its seismo-stratigraphic architecture over the last 350 kyr. Over such time range, through the identification of the paleoshoreline deposits, we estimated an average subsidence rate of about 1.2 mm/yr.