Polycrystalline diamond thin film as wide bandgap material: the optoelectronic behaviour and the relationship with the structure

In this work metal - Microwave Plasma CVD diamond Schottky devices were studied. The current density vs. applied voltage reveals rectification ratios up to 10(4) at \ +/- 2V \. Under illumination an inversion and increase of the rectification is observed. The carrier density is 10(15) cm(-3) and the ideality factors near 1.5. The dark current vs. temperature shows that below 150 K the bulk transport is controlled by a hopping process with a density of defects of 10(16) cm(-3). For higher temperatures an extrinsic ionisation with activation energy of 0.3 eV takes place. The correlation with the polycrystalline nature of the samples is focused.

Interface properties and capacitance-voltage behaviour of diamond devices prepared by microwave-assisted CVD

Free standing diamond films were used to study the effect of diamond surface morphology and microstructure on the electrical properties of Schottky barrier diodes. By using free standing films both the rough top diamond surface and the very smooth bottom surface are available for post-metal deposition. Rectifying electrical contacts were then established either with the smooth or the rough surface. The estimate of doping density from the capacitance-voltage plots shows that the smooth surface has a lower doping density when compared with the top layers of the same film. The results also show that surface roughness does not contribute significantly to the frequency dispersion of the small signal capacitance. The electrical properties of an abrupt asymmetric n(+)(silicon)-p(diamond) junction have also been measured. The I-V curves exhibit at low temperatures a plateau near zero bias, and show inversion of rectification. Capacitance-voltage characteristics show a capacitance minimum with forward bias, which is dependent on the environment conditions. It is proposed that this anomalous effect arises from high level injection of minority carriers into the bulk.

Photoconductivity and electrical properties of diamond films grown by MPCVD

The electrical and photoconductive features of as-grown microwave-plasma-assisted chemical-vapour deposition (MPCVD) diamond films are studied in correlation with magnetic results obtained from electron paramagnetic resonance (EPR). Also, the morphology is analysed by atomic force microscopy (AFM) showing [111] crystals with a good uniformity of the deposit. The photoresponse as well the current-voltage features observed show an efficient photogeneration of carriers while the optoelectronic characteristics of the metal-diamond junction have an ideality factor of 1.6 together with a rectification ratio of about 10(4) at +/-2.5 V. The nature of the mechanisms responsible for the conduction is discussed. (C) 1998 Elsevier Science S.A.

Electrical AC behaviour of MPCVD diamond Schottky diodes

The present work reports some experimental results on the electrical AC behaviour of metal-undoped diamond Schottky diodes fabricated with a free-standing MPCVD diamond film (5 mum thick). The metals are gold for the ohmic contact and aluminium for the rectifier. The capacitance and loss tangent vs, frequency shows that capacitance presents a relaxation maximum at frequencies near 10 kHz at room temperature. Although the simple model (small equivalent circuit) can justify the values for the relaxation, it cannot justify the departure from the Debye model, also verified in the Cole-Cole plot. Taking into account the existence of traps in the depletion region, a best fit to the experimental results was obtained. The difference between the Fermi level and the band edge of 0.2-0.3 eV is in agreement with the activation energy found from the loss tangent analysis. The capacitance with applied voltage (Mott-Schottky plots) gives a defect density of 10(16) cm(-3) with contact potentials near 0.5 V and the profile of defect density obtained shows a major density (approx. 10(17) cm(-3)) in a layer with a thickness less than 50 nm from the junction, decreasing by one order of magnitude with increasing distance. Finally a structural model is proposed to explain the AC behaviour found. (C) 2001 Elsevier Science B.V. All rights reserved.

Large scale fabrication of nitrogen vacancy-embedded diamond nanostructures for single-photon source applications

Some color centers in diamond can serve as quantum bits which can be manipulated with microwave pulses and read out with laser, even at room temperature. However, the photon collection efficiency of bulk diamond is greatly reduced by refraction at the diamond/air interface. To address this issue, we fabricated arrays of diamond nanostructures, differing in both diameter and top end shape, with HSQ and Cr as the etching mask materials, aiming toward large scale fabrication of single-photon sources with enhanced collection efficiency made of nitrogen vacancy (NV) embedded diamond. With a mixture of O2 and CHF3 gas plasma, diamond pillars with diameters down to 45 nm were obtained. The top end shape evolution has been represented with a simple model. The tests of size dependent single-photon properties confirmed an improved single-photon collection efficiency enhancement, larger than tenfold, and a mild decrease of decoherence time with decreasing pillar diameter was observed as expected. These results provide useful information for future applications of nanostructured diamond as a single-photon source.

Investigation of bonded hydrogen defects in nanocrystalline diamond films grown with nitrogen/methane/hydrogen plasma at high power conditions

In this work, we investigate the influence of some growth parameters such as high microwave power ranging from 3.0 to 4.0 kW and N2 additive on the incorporation of bonded hydrogen defects in nanocrystalline diamond (NCD) films grown through a small amount of pure N2 addition into conventional 4% CH4/H2 plasma using a 5 kW microwave plasma CVD system. Incorporation form and content of hydrogen point defects in the NCD films produced with pure N2 addition was analyzed by employing Fourier-transform infrared (FTIR) spectroscopy for the first time. A large amount of hydrogen related defects was detected in all the produced NCD films with N2 additive ranging from 29 to 87 µm thick with grain size from 47 nm to 31 nm. Furthermore, a specific new H related sharp absorption peak appears in all the NCD films grown with pure N2/CH4/H2 plasma at high powers and becomes stronger at powers higher than 3.0 kW and is even stronger than the 2920 cm−1 peak, which is commonly found in CVD diamond films. Based on these experimental findings, the role of high power and pure nitrogen addition on the growth of NCD films including hydrogen defect formation is analyzed and discussed.

Sticking non-stick: surface and structure control of diamond-like carbon in plasma enhanced chemical vapour deposition

This short review article explores the practical use of diamond-like carbon (DLC) produced by plasma enhanced chemical vapour deposition (PECVD). Using as an example issues relating to the DLC coating of a hand-held surgical device, we draw on previous works using atomic force microscopy, X-ray photoelectron spectroscopy, Raman spectroscopy, scanning electron microscopy, tensiometry and electron paramagnetic resonance. Utilising data from these techniques, we examine the surface structure, substrate-film interface and thin film microstructure, such as sp2/sp3 ratio (graphitic/diamond-like bonding ratio) and sp2 clustering. We explore the variations in parameters describing these characteristics, and relate these to the final device properties such as friction, wear resistance, and diffusion barrier integrity. The material and device characteristics are linked to the initial plasma and substrate conditions.

Size selectivity of diamond and square mesh cod ends for four by-catch species in the crustacean fishery off the Portuguese south coast

The effects of an increase in cod end mesh size from 55 to 60 and 70 mm and a change of mesh configuration from 55 mm diamond to 55 turn square mesh on the size selectivity of four by-catch species (the red shrimp Aristeus antennatus, the European hake Merluccius merluccius, the horse mackerel Trachurus trachurus and the blue whiting Micromesistius poutassou) commonly captured in the crustacean fishery off the Portuguese south coast, were evaluated. Selectivity parameters for blue whiting, the most abundant species in the catches, were estimated taking into account between-haul variation, while for the remaining species, captured in much lower quantities, the selectivity estimates were based on pooled data by length class for all hauls within the same cod end. Length at 50% retention, L-50, was found to increase with mesh size and with the change in mesh configuration for all the studied species. For blue whiting trawling depth and cod end catch were found to play a role in between-haul variation by increasing L-50 as well. The results suggest that an increase in the current minimum mesh size of 55-70 mm would be advisable to be compatible with the minimum landing sizes (MLSs) of 29 mm carapace length and 27 cm total length for red shrimp and hake, respectively, while it would greatly reduce the amount of discards, particularly those for blue whiting, that accounted for approximately 50% of the total catch weight. Horse mackerel was the only species for which the use of a larger mesh size would result in a significant escapement of individuals above the MLS of 15 cm. (C) 2002 Elsevier Science B.V. All rights reserved.

Size selectivity of diamond and square mesh cod ends for rose shrimp (Parapenaeus longirostris) and Norway lobster (Nephrops norvegicus) off the Portuguese south coast

The effects of an increase in cod end mesh size from 55 to 60 and 70 mm and a change of mesh configuration from diamond to square mesh on the size selectivity for rose shrimp Parapenaeus longirostris and Norway lobster Nephrops norvegicus captured off the Portuguese south coast were evaluated. The results were analysed taking into account between-haul variation in selectivity, and indicate a significant increase in L-50 for rose shrimp with an increase in mesh size or with the use of a square mesh cod end, while for Norway lobster only mesh configuration was found to affect this parameter. Two other important external variables were identified; the trawling depth and the cod end catch, which influence between-haul variation, by increasing the selection range for rose shrimp and Norway lobster, respectively. The results obtained suggest that an increase in the current minimum mesh size of 55 mm would be advisable for rose shrimp in order to respect the minimum landing size of 24 mm carapace length presently established for this species. Moreover, trawling for rose shrimp should be avoided at depths above 200 m, in order to avoid catches consisting almost exclusively of juveniles. Such an increase in mesh size would have a minor impact in terms of losses of individuals above the minimum landing size for Norway lobster and would contribute to reducing the amount of discards in this fishery. (C) 2002 Elsevier Science B.V. All rights reserved.

Electronic states of trans-polyacetylene, poly(p-phenylene vinylene) and sp-hybridised carbon species in amorphous hydrogenated carbon probed by resonant Raman scattering

Inclusions of sp-hybridised, trans-polyacetylene [trans-(CH)x] and poly(p-phenylene vinylene) (PPV) chains are revealed using resonant Raman scattering (RRS) investigation of amorphous hydrogenated carbon (a-C:H) films in the near IR – UV range. The RRS spectra of trans-(CH)x core Ag modes and the PPV CC-H phenylene mode are found to transform and disperse as the laser excitation energy ћωL is increased from near IR through visible to UV, whereas sp-bonded inclusions only become evident in UV. This is attributed to ћωL probing of trans-(CH)x chain inhomogeneity and the distribution of chains with varying conjugation length; for PPV to the resonant probing of phelynene ring disorder; and for sp segments, to ћωL probing of a local band gap of end-terminated polyynes. The IR spectra analysis confirmed the presence of sp, trans-(CH)x and PPV inclusions. The obtained RRS results for a-C:H denote differentiation between the core Ag trans-(CH)x modes and the PPV phenylene mode. Furthermore, it was found that at various laser excitation energies the changes in Raman spectra features for trans-(CH)x segments included in an amorphous carbon matrix are the same as in bulk trans-polyacetylene. The latter finding can be used to facilitate identification of trans-(CH)x in the spectra of complex carbonaceous materials.

Internationalization of Chinese and Korean firms

This article compares and contrasts the growth of Chinese and Korean multinational enterprises (MNEs). The article identifies the similarities and differences between Chinese and Korean MNEs in terms of motivations for internationalization, expansion strategies, and paths. The goal of this article is to contribute to the literature by shifting focus on host-country conditions to home-country conditions in explaining the drivers for firms' internationalization. We conclude that firms are motivated to expand abroad when faced with domestic competitive disadvantages resulting from absence or deficiency of one or more of Porter's Diamond attributes in their domestic market. Implications for further studies are also explored.

Union strategies in representing ‘new’ workers : the comparative case of UK and Australian retail unions

This paper is a comparative exploratory study of the changing nature of employee voice through trade union representation in the retail industry in the UK and Australia. In both countries, the retail industry is a major employer and is one of the few private sector service industries with significant union membership (Griffin et al 2003). The relevant unions, the Distributive and Allied Workers Union (USDAW) and the Shop, Distributive and Allied Union (SDA), are the fourth largest and largest unions in the UK and Australia respectively. However, despite this seeming numerical strength in membership, the characteristics of the industry provide unique challenges for employee voice and representation. The significance of the study is that any extension of representation and organisation by unions in the retail sector is valuable socially and politically, given that retail workers are often categorised a s vulnerable, due to their low pay, the predominance of disadvantaged labour market groups such a s women and young people, workers’ atypical employment arrangements and, in the case of the UK, variable levels of union recognition which inhibit representation (Broadbridge 2002; Henley 2006; Lynch 2005; Roan & Diamond 2003; Reynolds et al 2005). In addition, specifically comparative projects have value in that they allow some variables relating to the ‘industry’ to be held constant, thus reducing the range of potential explanations of differences in union strategy. They also have value in that the research partners may be more likely to notice and problematise taken-for-granted aspects of practices in another country, thus bringing to the fore key features and potentially leading to theoretical innovation. Finally, such projects may assist in transnational diffusion of union strategy.

External pressure in the hardening of phosphate in tribofilm on iron surfaces

Purpose: In the present work we consider our (in progress) spectroscopy study of zinc and iron phosphates under the influence external high pressure to determine zinc ion change coordination from tetrahedral to octahedral (or hexahedral) structure.----- Design/methodology/approach: The standard equipment is the optical high pressure cell with diamond (DAC). The DAC is assembled and then vibrational or electronic spectra are collected by mounting the cell in an infrared, Raman, EXAFS or UV-visible spectrometer.----- Findings: Mechanism by which zinc and iron methaphosphate material is transformed to glassy meta-phosphate is enhancing mechanical properties of tribofilm. The two decades of intensive study demonstrates that Zn (II) and Fe (III) ions participate to cross-link network under friction, hardening the phosphate.----- Research limitations/implications: Transition metal atoms with d orbital have flexible coordination numbers, for example zinc acts as a cross-linking agent increasing hardness, by changing coordination from tetrahedral to octahedral. Perhaps the external pressure effect on the [Zn–(O-P-)4 ] complex causes a transformation to an [Zn –(O-P-)6] grouping.----- Originality/value: This paper analyses high-pressure spectroscopy which has been applied for the investigation of 3D transition metal ions in solids. When studying pressure effects on coordination compounds structure, we can expect changes in ground electronic state (spin-crossovers), electronic spectra due to structural distortions (piezochromism), and changes in the ligand field causing shifts in the electronic transitions.