Dextrous hands: issues relating to a four-finger articulated hand

Manipulation of an object by a multi-fingered robot hand requires task planning which involves computation of joint space vectors and fingertip forces. To implement a task as fast as possible, computations have to be carried out in minimum time. The state of the art in manipulation by multi-fingered robot hand designs has shown the possible use of remotely driven finger joints. Such remotely driven hands require computation of tendon displacement for evaluating joint space vectors before signals are sent to actuators. Alternatively, a direct drive hand is a mechanical hand in which the shafts of articulated joints are directly coupled to the rotors of motors with high output torques. This article has been divided into two main sections. The first section presents a brief view of manipulation using a direct drive approach. Meanwhile, the other section presents ongoing research which is being carried out to design a four-finger articulated hand in the Department of Cybernetics at the University of Reading.

Head-controlled assistive telerobot with extended physiological proprioception capability

People with disabilities such as quadriplegia can use mouth-sticks and head-sticks as extension devices to perform desired manipulations. These extensions provide extended proprioception which allows users to directly feel forces and other perceptual cues such as texture present at the tip of the mouth-stick. Such devices are effective for two principle reasons: because of their close contact with the user's tactile and proprioceptive sensing abilities; and because they tend to be lightweight and very stiff, and can thus convey tactile and kinesthetic information with high-bandwidth. Unfortunately, traditional mouth-sticks and head-sticks are limited in workspace and in the mechanical power that can be transferred because of user mobility and strength limitations. We describe an alternative implementation of the head-stick device using the idea of a virtual head-stick: a head-controlled bilateral force-reflecting telerobot. In this system the end-effector of the slave robot moves as if it were at the tip of an imaginary extension of the user's head. The design goal is for the system is to have the same intuitive operation and extended proprioception as a regular mouth-stick effector but with augmentation of workspace volume and mechanical power. The input is through a specially modified six DOF master robot (a PerForceTM hand-controller) whose joints can be back-driven to apply forces at the user's head. The manipulation tasks in the environment are performed by a six degree-of-freedom slave robot (the Zebra-ZEROTM) with a built-in force sensor. We describe the prototype hardware/software implementation of the system, control system design, safety/disability issues, and initial evaluation tasks.

Transputer based real time robot control

A parallel processor architecture based on a communicating sequential processor chip, the transputer, is described. The architecture is easily linearly extensible to enable separate functions to be included in the controller. To demonstrate the power of the resulting controller some experimental results are presented comparing PID and full inverse dynamics on the first three joints of a Puma 560 robot. Also examined are some of the sample rate issues raised by the asynchronous updating of inertial parameters, and the need for full inverse dynamics at every sample interval is questioned.

Robotic multiwell planar patch-clamp for native and primary mammalian cells

Robotic multiwell planar patch-clamp has become common in drug development and safety programs because it enables efficient and systematic testing of compounds against ion channels during voltage-clamp. It has not, however, been adopted significantly in other important areas of ion channel research, where conventional patch-clamp remains the favored method. Here, we show the wider potential of the multiwell approach with the ability for efficient intracellular solution exchange, describing protocols and success rates for recording from a range of native and primary mammalian cells derived from blood vessels, arthritic joints and the immune and central nervous systems. The protocol involves preparing a suspension of single cells to be dispensed robotically into 4-8 microfluidic chambers each containing a glass chip with a small aperture. Under automated control, giga-seals and whole-cell access are achieved followed by preprogrammed routines of voltage paradigms and fast extracellular or intracellular solution exchange. Recording from 48 chambers usually takes 1-6 h depending on the experimental design and yields 16-33 cell recordings.

Effect of shear rupture on aggregate scale formation in sea ice

A discrete element model is used to study shear rupture of sea ice under convergent wind stresses. The model includes compressive, tensile, and shear rupture of viscous elastic joints connecting floes that move under the action of the wind stresses. The adopted shear rupture is governed by Coulomb’s criterion. The ice pack is a 400 km long square domain consisting of 4 km size floes. In the standard case with tensile strength 10 times smaller than the compressive strength, under uniaxial compression the failure regime is mainly shear rupture with the most probable scenario corresponding to that with the minimum failure work. The orientation of cracks delineating formed aggregates is bimodal with the peaks around the angles given by the wing crack theory determining diamond-shaped blocks. The ice block (floe aggregate) size decreases as the wind stress gradient increases since the elastic strain energy grows faster leading to a higher speed of crack propagation. As the tensile strength grows, shear rupture becomes harder to attain and compressive failure becomes equally important leading to elongation of blocks perpendicular to the compression direction and the blocks grow larger. In the standard case, as the wind stress confinement ratio increases the failure mode changes at a confinement ratio within 0.2–0.4, which corresponds to the analytical critical confinement ratio of 0.32. Below this value, the cracks are bimodal delineating diamond shape aggregates, while above this value failure becomes isotropic and is determined by small-scale stress anomalies due to irregularities in floe shape.

Modelling the reorientation of sea-ice faults as the wind changes direction

A discrete-element model of sea ice is used to study how a 90° change in wind direction alters the pattern of faults generated through mechanical failure of the ice. The sea-ice domain is 400km in size and consists of polygonal floes obtained through a Voronoi tessellation. Initially the floes are frozen together through viscous–elastic joints that can break under sufficient compressive, tensile and shear deformation. A constant wind-stress gradient is applied until the initially frozen ice pack is broken into roughly diamond-shaped aggregates, with crack angles determined by wing-crack formation. Then partial refreezing of the cracks delineating the aggregates is modelled through reduction of their length by a particular fraction, the ice pack deformation is neglected and the wind stress is rotated by 90°. New cracks form, delineating aggregates with a different orientation. Our results show the new crack orientation depends on the refrozen fraction of the initial faults: as this fraction increases, the new cracks gradually rotate to the new wind direction, reaching 90° for fully refrozen faults. Such reorientation is determined by a competition between new cracks forming at a preferential angle determined by the wing-crack theory and at old cracks oriented at a less favourable angle but having higher stresses due to shorter contacts across the joints

An Alternative Section Method for Casting and Posterior Laser Welding of Metallic Frameworks for an Implant-Supported Prosthesis

Purpose: The aim of this study was to compare the accuracy of fit of three types of implant-supported frameworks cast in Ni-Cr alloy: specifically, a framework cast as one piece compared to frameworks cast separately in sections to the transverse or the diagonal axis, and later laser welded. Materials and Methods: Three sets of similar implant-supported frameworks were constructed. The first group of six 3-unit implant-supported frameworks were cast as one piece, the second group of six were sectioned in the transverse axis of the pontic region prior to casting, and the last group of six were sectioned in the diagonal axis of the pontic region prior to casting. The sectioned frameworks were positioned in the matrix (10 N(.)cm torque) and laser welded. To evaluate passive fit, readings were made with an optical microscope with both screws tightened and with only one-screw tightened. Data were submitted to ANOVA and Tukey-Kramer`s test (p < 0.05). Results: When both screws were tightened, no differences were found between the three groups (p > 0.05). In the single-screw-tightened test, with readings made opposite to the tightened side, the group cast as one piece (57.02 +/- 33.48 mu m) was significantly different (p < 0.05) from the group sectioned diagonally (18.92 +/- 4.75 mu m) but no different (p > 0.05) from the group transversally sectioned (31.42 +/- 20.68 mu m). On the tightened side, no significant differences were found between the groups (p > 0.05). Conclusions: Results of this study showed that casting diagonally sectioned frameworks lowers misfit levels of prosthetic implant-supported frameworks and also improves the levels of passivity to the same frameworks when compared to structures cast as one piece.

Comparative analysis of the fit of 3-unit implant-supported frameworks cast in nickel-chromium and cobalt-chromium alloys and commercially pure titanium after casting, laser welding, and simulated porcelain firings

This study compared the vertical misfit of 3-unit implant-supported nickel-chromium (Ni-Cr) and cobalt-chromium (Co-Cr) alloy and commercially pure titanium (cpTi) frameworks after casting as 1 piece, after sectioning and laser welding, and after simulated porcelain firings. The results on the tightened side showed no statistically significant differences. On the opposite side, statistically significant differences were found for Co-Cr alloy (118.64 mu m [SD: 91.48] to 39.90 mu m [SD: 27.13]) and cpTi (118.56 mu m [51.35] to 27.87 mu m [12.71]) when comparing 1-piece to laser-welded frameworks. With both sides tightened, only Co-Cr alloy showed statistically significant differences after laser welding. Ni-Cr alloy showed the lowest misfit values, though the differences were not statistically significantly different. Simulated porcelain firings revealed no significant differences.

Modified section method for laser-welding of ill-fitting cp Ti and Ni-Cr alloy one-piece cast implant-supported frameworks

P>This study aimed to verify the effect of modified section method and laser-welding on the accuracy of fit of ill-fitting commercially pure titanium (cp Ti) and Ni-Cr alloy one-piece cast frameworks. Two sets of similar implant-supported frameworks were constructed. Both groups of six 3-unit implant-supported fixed partial dentures were cast as one-piece [I: Ni-Cr (control) and II: cp Ti] and evaluated for passive fitting in an optical microscope with both screws tightened and with only one screw tightened. All frameworks were then sectioned in the diagonal axis at the pontic region (III: Ni-Cr and IV: cp Ti). Sectioned frameworks were positioned in the matrix (10-Ncm torque) and laser-welded. Passive fitting was evaluated for the second time. Data were submitted to anova and Tukey-Kramer honestly significant difference tests (P < 0 center dot 05). With both screws tightened, one-piece cp Ti group II showed significantly higher misfit values (27 center dot 57 +/- 5 center dot 06 mu m) than other groups (I: 11 center dot 19 +/- 2 center dot 54 mu m, III: 12 center dot 88 +/- 2 center dot 93 mu m, IV: 13 center dot 77 +/- 1 center dot 51 mu m) (P < 0 center dot 05). In the single-screw-tightened test, with readings on the opposite side to the tightened side, Ni-Cr cast as one-piece (I: 58 center dot 66 +/- 14 center dot 30 mu m) was significantly different from cp Ti group after diagonal section (IV: 27 center dot 51 +/- 8 center dot 28 mu m) (P < 0 center dot 05). On the tightened side, no significant differences were found between groups (P > 0 center dot 05). Results showed that diagonally sectioning ill-fitting cp Ti frameworks lowers misfit levels of prosthetic implant-supported frameworks and also improves passivity levels of the same frameworks when compared to one-piece cast structures.

Mobius Sequence in a Girl and Arthrogryposis in her Half-Brother: Distinct Phenotypes Caused By Prenatal Injuries

Mobius sequence is a congenital facial and abducens nerve palsy, frequently associated to abnormalities of extremities. Arthrogryposis multiplex congenital is defined as a congenital fixation of multiple joints seldom of neurogenic origin. Both sequences must have a genetic origin, but usually are sporadic cases related to environmental factors such as drugs exposition and maternal trauma. A 5-year-old girl and a 1-year-old boy were born with Mobius sequence and arthrogryposis multiplex congenital, respectively. During pregnancies, the mother had vaginal bleeding at 7 weeks and used crack (free-based cocaine) in the first trimester, respectively. The girl also has equinovarus talipes and autistic behavior. The boy has arthrogryposis with flexion contractures of the feet and knees. A vascular disruption, due to hemorrhage and cocaine exposure, causing a transient ischemic insult to embryos in a critical period of development may be responsible for distinct phenotypes in these cases.

Mating behavior of Sickius longibulbi (Araneae, Theraphosidae, Ischnocolinae), a spider that lacks spermathecae

We describe the mating behavior in the spermatheca-lacking theraphosid species Sickius longibulbi Soares & Camargo 1948. The behavior in captivity of nine pairs of S. longibulbi was videotaped and analyzed. The matting of this species presented an uncommon theraphosid pattern. There is little in the way of overt courtship by the male, the primary behavior seen being the male`s use of legs I and II to touch the female`s first pairs of legs and her chelicerae. Sometimes the male clasped one of the female`s first pairs of legs, bringing her close to him. While the female raised her body, the male clasped her fangs and held her tightly with his legs III wrapped around her prosoma. The male seemed to try to knock the female down, pushing her entire body until she lay on her dorsum. In this phase we observed the male biting the female on the sternum or on the leg joints. When the female fell, the male attempted to position himself at an angle of 90 degrees from the female. These movements appear to demand a lot of energy, particularly because the female is not passive during the mating. Our findings suggest that copulating in this position is, for the male, more successful than adopting other positions because it allows his extremely long palpal bulbs to deposit more sperm in the female oviduct where - since she lacks spermathecae - she retains the sperm. We suggest that the further he reaches into the oviduct, the greater the chance that he will fertilize the female`s eggs.

Jämförelsestudie avseende stomsystem : Ramverk eller fackverk/balk/pelar-system

Projektet omfattade en jämförelsestudie avseende stomsystem. Studien undersökte ramverk och fackverk/balk/pelar-system och genomfördes självständigt med stöttning av Ramböll AB´s kontor i Falun. Syftet var främst att undersöka vilka skillnader det finns mellan tvåledsramar och fackverk/balk/pelar-system för lätta hallbyggnader och försöka få klarhet i varför fackverk/balk/pelar-system är det dominerande systemet i Sverige eftersom övriga Europa har tagit en annan utveckling och domineras av tvåledsramar. Studien undersöker skillnaderna mellan systemen i en hallbyggnad med förutbestämda mått i stål.Inledningsvis gjordes en litteraturstudie för att få en bredare bakgrund av systemen och en bättre förståelse om förutsättningarna för varje system. Efter litteraturstudien kunde sedan ett typhus och beräkningsunderlag för jämförelsestudien tas fram. Även en enkätstudie gjordes med syftet att skapa en tydlig bild av vilket stomsystem konstruktörer i Sverige oftast väljer och varför. Resultatet av studien visade att tvåledsramar ger en ökad kostnad jämfört med fackverk/balk/pelar-system i materialåtgång och framställning samt att beräkningarna blir mer komplicerade. Skulle fortsatta studier göras med dessa system i byggnader med andra mått skulle det kanske gå att få fram speciella mått på byggnader där kostnaden för tvåledsramar blir densamma som för fackverk/balk/pelar-system och därför är ett likvärdigt alternativ som stomsystem.En viktig slutsats från projektet är att tvåledsramar används mycket mer sällan än fackverk/balk/pelar-system som stomsystem i lätta hallbyggnader i Sverige på grund av att kostnaderna blir mycket högre med tvåledsramar och att det är ett mer komplicerat system i beräkningsarbetet. De viktigaste slutsatserna från jämförelsestudien går att sammafatta som följande: Tvåledsramar är dyrare att använda. Tvåledsramar är ett mer komplicerat system beräkningsmässigt. Traditionen av att använda tvåledsramar finns inte och därför används inte systemet.

High-precision five-axis machine for high-speed material processing using linear motors and parallel-serial kinematics

The paper describes some details of the mechanical and kinematics design of a five-axis mechanism. The design has been utilized to physically realize an industrial-scale five-axis milling machine that can carry a three KW spindle. However, the mechanism could be utilized in other material processing and factory automation applications. The mechanism has five rectilinear joints/axes. Two of these axes are arranged traditionally, i.e. in series, and the other three axes utilize the concept of parallel kinematics. This combination results in a design that allows three translational and two rotational two-mode degrees of freedom (DOFs). The design provides speed, accuracy and cost advantages over traditional five-axis machines. All axes are actuated using linear motors.

Investigation of processing conditions of melded parts to determine process boundaries

Melding, a novel method for producing seamless joints in thermosetting composites utilising the Quickstep™ process, is explored in this paper. The effect of processing conditions on the quality of melded joins is examined and a set of processing boundaries defined so that the strength of melded joints is optimized. HexPly® 914c pre-preg material was exposed to a range of processing temperatures prior to joining via the melding process. Differential Scanning Calorimetry analysis was carried out to investigate the degree of cure of material prior to final joining, and it was found that minimal cure occurs at temperatures below 120°C. After consolidation and cure of the melded parts, short beam shear testing was conducted to evaluate the strength of the melded interface. Exposure temperatures between 65°C and 120°C were found to optimize short beam shear join strength. Mode I double cantilever beam and mode II end notched flexural tests showed no detrimental effect of elevated exposure temperatures prior to joining.

Sculptural abstraction of landscape

The purpose of my Senior Scholar project was to create a series of sculptures that are based on the interaction of natural forms within a selected landscape setting. I hope to convey a sense of how I view and interpret the landscape and to create works that stimulate a sense of wonder in the mind of the viewer. This fascination, perhaps even obsession, with the power of the landscape has kept me going throughout the year. As a source of ideas and imagery, the landscape can never be depleted. There will always be new combinations of landscape elements, different light conditions, and changing seasons to provide me with fresh ideas. Research for the project took me to many different places, be it my trip to Monhegan Island or driving to New York City to study the cityscape. I began the year working in steel and plaster, combining the two in works that explore the interaction between living tree roots and inanimate rocks. This led to a series entitled Landscape Recollections, comprised of welded steel forms housed in protective wooden boxes and lit from inside. After visiting New York City, architecture began to playa role in my work, as seen in the two Roadcut pieces and the Cathedral Woods series. Roadcut #1 and Roadcut #2 explore the relationship between a man-made road and the landscape that lies beneath and around it. The Cathedral Woods pieces incorporate architecture in a more abstract manner, using imagery derived from Gothic cathedrals to convey a sense of quiet peacefulness. The soaring verticality of Gothic architecture integrates with the tall tree forms in each piece, enabling me to intertwine these two elements into one another and create a harmonious relationship between architecture and nature. Throughout the year I have kept a sketchbook in which I draw from life, jot down ideas, and take notes on how the project is progressing. I have also completed several large charcoal drawings of my sculptures in which I explore different ways of viewing the steel forms. I am grateful to have had the opportunity to undertake this project, as it has been a very difficult but rewarding process of observing, interpreting, and manifesting the landscape according to my personal vision and experiences.