Avaliação da fotodegradação de poliolefinas através de exposição natural e artificial

Samples of polypropylene (PP) and low-density polyethylene (LDPE) were submitted to ultraviolet radiation, in the natural environment and also in the laboratory. Chemical modifications were quantified by the carbonyl index (CI), mechanical properties and melt flow index. The degradation in the laboratory was comparatively faster than in the environment for both types of polymers. The accelerating factor was determined for the various properties investigated. This parameter, however, showed a large variation with the degradation criteria and the type of polymer. The existence of a "universal accelerating factor", therefore, was not observed in the current study.

Estudo teórico da interação existente entre a artemisinina e o heme

The purpose of this work is to study theoretically stereoelectronic aspects of the interaction between heme and artemisinin in the transitional heme-artemisinin complex. Through semi-empirical calculations using the PM3 method, the potential energy barrier of artemisinin rotation relative to heme in the heme-artemisinin complex was studied in vacuum and in the partially solvated state. The minimum heat of formation obtained for the complex with and without water molecules is -702.39 and -100.86 kcal mol-1, respectively, which corresponds to the dihedral angle C-Fe-O1-O2 of 43.93º and 51.90º around the iron-oxygen O1 bond, respectively. The water molecules bind to heme via 13 hydrogen bonds and O-H•••O and 6 C-H•••O interactions, which accounts for -67.23 kcal mol-1. It is observed that the inclusion of water molecules does not affect significantly the stability of the heme-artemisinin complex.

Cafeína: revisão sobre métodos de análise

Gravimetric and Bailey-Andrew methods are tedious and provide inflated results. Spectrofotometry is adequate for caffeine analysis but is lengthy. Gas chromatography also is applied to the caffeine analysis but derivatization is needed. High performance liquid chromatography with ultraviolet detection (HPLC-UV) and reversed phase is simple and rapid for xanthine multianalysis. In HPLC-UV-gel permeation, organic solvents are not used. HPLC-mass spectrometry provides an unequivocal structural identification of xanthines. Capillary electrophoresis is fast and the solvent consumption is smaller than in HPLC. Chemometric methods offer an effective means for chemical data handling in multivariate analysis. Infrared spectroscopy alone or associated with chemometries could predict the caffeine content in a very accurate form. Electroanalytical methods are considered of low cost and easy application in caffeine analysis.

Obtenção de titânio metálico com porosidade controlada por metalurgia do pó

Titanium is an attractive material for structural and biomedical applications because of its excellent corrosion resistance, biocompatibility and high strength-to-weight ratio. The high reactivity of titanium in the liquid phase makes it difficult to produce it by fusion. Powder metallurgy has been shown to be an adequate technique to obtain titanium samples at low temperatures and solid-phase consolidation. The production of compacts with different porosities obtained by uniaxial pressing and vacuum sintering is briefly reviewed. Powder particle size control has been shown to be very important for porosity control. Sample characterization was made using scanning electron microscopy (SEM) images.

Blackbody emission under laser excitation of silicon nanopowder produced by plasma-enhanced chemical-vapor deposition

Previous results concerning radiative emission under laser irradiation of silicon nanopowder are reinterpreted in terms of thermal emission. A model is developed that considers the particles in the powder as independent, so under vacuum the only dissipation mechanism is thermal radiation. The supralinear dependence observed between the intensity of the emitted radiation and laser power is predicted by the model, as is the exponential quenching when the gas pressure around the sample increases. The analysis allows us to determine the sample temperature. The local heating of the sample has been assessed independently by the position of the transverse optical Raman mode. Finally, it is suggested that the photoluminescence observed in porous silicon and similar materials could, in some cases, be blackbody radiation

Processamento de pilhas Li/MnO2 usadas

This work presents two recycling processes for spent Li/MnO2 batteries. After removal of the solvent under vacuum the cathode + anode + electrolyte was submitted to one of the following procedures: (a) it was calcined (500 ºC, 5 h) and the calcined solid was submitted to solvent extraction with water in order to recover lithium salts. The residual solid was treated with sulfuric acid containing hydrogen peroxide. Manganese was recovered as sulfate; (b) the solid was treated with potassium hydrogeno sulfate (500 ºC, 5 h). The solid was dissolved in water and the resulting solution was added dropwise to sodium hydroxide. Manganese was recovered as dioxide. The residual solution was treated with potassium fluoride in order to precipitate lithium fluoride.

Reactions of Chlorambucil and its main metabolite, Phenylacetic Acid Mustard, with 2’-deoxyribonucleosides and Calf Thymus DNA

Chlorambucil is an anticancer agent used in the treatment of a variety of cancers, especially in chronic lymphocytic leukemia, and autoimmune diseases. Nevertheless, chlorambucil is potentially mutagenic, teratogenic and carcinogenic. The high antitumor activity and high toxicity of chlorambucil and its main metabolite, phenylacetic acid mustard, to normal tissues have been known for a long time. Despite this, no detailed chemical data on their reactions with biomolecules in aqueous media have been available. The aim of the work described in this thesis was to analyze reactions of chlorambucil with 2’-deoxyribonucleosides and calf thymus DNA in aqueous buffered solution, at physiological pH, and to identify and characterize all adducts by using modern analyzing methods. Our research was also focused on the reactions of phenylacetic acid mustard with 2’-deoxynucleosides under similar conditions. A review of the literature consisting of general background of nucleic acids, alkylating agents and ultraviolet spectroscopy used to identify the purine and pyrimidine nucleosides, as well as the results from experimental work are presented and discussed in this doctoral thesis.

Impact of maternity care policy in Catalonia: a retrospective cross-sectional study of service delivery in public and private hospitals

Background: As a result of the growing number of interventions that are now performed in the context of maternity care, health authorities have begun to examine the possible repercussions for service provision and for maternal and neonatal health. In Spain the Strategy Paper on Normal Childbirth was published in 2008, and since then the authorities in Catalonia have sought to implement its recommendations. This paper reviews the current provision of maternity care in Catalonia. Methods: This was a descriptive study. Hospitals were grouped according to their source of funding (public or private) and were stratified (across four strata) on the basis of the annual number of births recorded within their respective maternity service. Data regarding the distribution of obstetric professionals were taken from an official government survey of hospitals published in 2010. The data on obstetric interventions (caesarean, use of forceps, vacuum or non-specified instruments) performed in 2007, 2010 and 2012 were obtained by consulting discharge records of 44 public and 20 private hospitals, which together provide care in 98% of all births in Catalonia. Proportions and confidence intervals were calculated for each intervention performed in all full-term (3742 weeks) singleton births. Results: Analysis of staff profiles according to the stratification of hospitals showed that almost all the hospitals had more obstetricians than midwives among their maternity care staff. Public hospitals performed fewer caesareans [range between 19.20% (CI 18.84-19.55) and 28.14% (CI 27.73-28.54)] than did private hospitals [range between 32.21% (CI 31.78-32.63) and 39.43% (CI 38.98-39.87)]. The use of forceps has decreased in public hospitals. The use of a vacuum extractor has increased and is more common in private hospitals. Conclusions: Caesarean section is the most common obstetric intervention performed during full-term singleton births in Catalonia. The observed trend is stable in the group of public hospitals, but shows signs of a rise among private institutions. The number of caesareans performed in accredited public hospitals covers a limited range with a stable trend. Among public hospitals the highest rate of caesareans is found in non-accredited hospitals with a lower annual number of births.

Impact of maternity care policy in Catalonia: a retrospective cross-sectional study of service delivery in public and private hospitals

Background: As a result of the growing number of interventions that are now performed in the context of maternity care, health authorities have begun to examine the possible repercussions for service provision and for maternal and neonatal health. In Spain the Strategy Paper on Normal Childbirth was published in 2008, and since then the authorities in Catalonia have sought to implement its recommendations. This paper reviews the current provision of maternity care in Catalonia. Methods: This was a descriptive study. Hospitals were grouped according to their source of funding (public or private) and were stratified (across four strata) on the basis of the annual number of births recorded within their respective maternity service. Data regarding the distribution of obstetric professionals were taken from an official government survey of hospitals published in 2010. The data on obstetric interventions (caesarean, use of forceps, vacuum or non-specified instruments) performed in 2007, 2010 and 2012 were obtained by consulting discharge records of 44 public and 20 private hospitals, which together provide care in 98% of all births in Catalonia. Proportions and confidence intervals were calculated for each intervention performed in all full-term (3742 weeks) singleton births. Results: Analysis of staff profiles according to the stratification of hospitals showed that almost all the hospitals had more obstetricians than midwives among their maternity care staff. Public hospitals performed fewer caesareans [range between 19.20% (CI 18.84-19.55) and 28.14% (CI 27.73-28.54)] than did private hospitals [range between 32.21% (CI 31.78-32.63) and 39.43% (CI 38.98-39.87)]. The use of forceps has decreased in public hospitals. The use of a vacuum extractor has increased and is more common in private hospitals. Conclusions: Caesarean section is the most common obstetric intervention performed during full-term singleton births in Catalonia. The observed trend is stable in the group of public hospitals, but shows signs of a rise among private institutions. The number of caesareans performed in accredited public hospitals covers a limited range with a stable trend. Among public hospitals the highest rate of caesareans is found in non-accredited hospitals with a lower annual number of births.

Dissolution test for glibenclamide tablets

The aim of this work is to develop and validate a dissolution test for glibenclamide tablets. Optimal conditions to carry out the dissolution test are 500 mL of phosphate buffer at pH 8.0, paddles at 75 rpm stirring speed, time test set to 60 min and using equipment with six vessels. The derivative UV spectrophotometric method for determination of glibenclamide released was developed, validated and compared with the HPLC method. The UVDS method presents linearity (r² = 0.9999) in the concentration range of 5-14 µg/mL. Precision and recoveries were 0.42% and 100.25%, respectively. The method was applied to three products commercially available on the Brazilian market.

Optical and microstructural properties of MgF2 UV coatings grown by ion beam sputtering process

The optical, mechanical, and microstructural properties of MgF2 single layers grown by ion beam sputtering have been investigated by spectrophotometric measurements, film stress characterization, x-ray photoelectron spectroscopy (XPS), x-ray diffraction, and transmission electron microscopy. The deposition conditions, using fluorine reactive gas or not, have been found to greatly influence the optical absorption and the stress of the films as well as their microstructure. The layers grown with fluorine compensation exhibit a regular columnar microstructure and an UV-optical absorption which can be very low, either as deposited or after thermal annealings at very low temperatures. On the contrary, layers grown without fluorine compensation exhibit a less regular microstructure and a high ultraviolet absorption which is particularly hard to cure. On the basis of calculations, it is shown that F centers are responsible for this absorption, whereas all the films were found to be stoichiometric, in the limit of the XPS sensitivity. On the basis of external data taken from literature, our experimental curves are analyzed, so we propose possible diffusion mechanisms which could explain the behaviors of the coatings.

Computational and Experimental Investigation of the Grooved Roll in Paper Machine Environment

In the paper machine, it is not a desired feature for the boundary layer flows in the fabric and the roll surfaces to travel into the closing nips, creating overpressure. In this thesis, the aerodynamic behavior of the grooved roll and smooth rolls is compared in order to understand the nip flow phenomena, which is the main reason why vacuum and grooved roll constructions are designed. A common method to remove the boundary layer flow from the closing nip is to use the vacuum roll construction. The downside of the use of vacuum rolls is high operational costs due to pressure losses in the vacuum roll shell. The deep grooved roll has the same goal, to create a pressure difference over the paper web and keep the paper attached to the roll or fabric surface in the drying pocket of the paper machine. A literature review revealed that the aerodynamic functionality of the grooved roll is not very well known. In this thesis, the aerodynamic functionality of the grooved roll in interaction with a permeable or impermeable wall is studied by varying the groove properties. Computational fluid dynamics simulations are utilized as the research tool. The simulations have been performed with commercial fluid dynamics software, ANSYS Fluent. Simulation results made with 3- and 2-dimensional fluid dynamics models are compared to laboratory scale measurements. The measurements have been made with a grooved roll simulator designed for the research. The variables in the comparison are the paper or fabric wrap angle, surface velocities, groove geometry and wall permeability. Present-day computational and modeling resources limit grooved roll fluid dynamics simulations in the paper machine scale. Based on the analysis of the aerodynamic functionality of the grooved roll, a grooved roll simulation tool is proposed. The smooth roll simulations show that the closing nip pressure does not depend on the length of boundary layer development. The surface velocity increase affects the pressure distribution in the closing and opening nips. The 3D grooved roll model reveals the aerodynamic functionality of the grooved roll. With the optimal groove size it is possible to avoid closing nip overpressure and keep the web attached to the fabric surface in the area of the wrap angle. The groove flow friction and minor losses play a different role when the wrap angle is changed. The proposed 2D grooved roll simulation tool is able to replicate the grooved aerodynamic behavior with reasonable accuracy. A small wrap angle predicts the pressure distribution correctly with the chosen approach for calculating the groove friction losses. With a large wrap angle, the groove friction loss shows too large pressure gradients, and the way of calculating the air flow friction losses in the groove has to be reconsidered. The aerodynamic functionality of the grooved roll is based on minor and viscous losses in the closing and opening nips as well as in the grooves. The proposed 2D grooved roll model is a simplification in order to reduce computational and modeling efforts. The simulation tool makes it possible to simulate complex paper machine constructions in the paper machine scale. In order to use the grooved roll as a replacement for the vacuum roll, the grooved roll properties have to be considered on the basis of the web handling application.

Cartilage Appearance Using an Environmental Scanning Electron Microscope.

Because of technical principles, samples to be observed with electron microscopy need to be fixed in a chemical process and exposed to vacuum conditions that can produce some changes in the morphology of the specimen. The aim of this work was to obtain high-resolution images of the fresh articular cartilage surface with an environmental scanning electron microscope (ESEM), which is an instrument that permits examination of biological specimens without fixation methods in a 10 Torr chamber pressure, thus minimizing the risk of creating artifacts in the structure. Samples from weight-bearing areas of femoral condyles of New Zealand white rabbits were collected and photographed using an ESEM. Images were analyzed using a categorization based in the Jurvelin classification system modified by Hong and Henderson. Appearance of the observed elevations and depressions as described in the classification were observed, but no fractures or splits of cartilage surface, thought to be artifacts, were detected. The ESEM is a useful tool to obtain images of fresh articular cartilage surface appearance without either employing fixation methods or exposing the specimen to extreme vacuum conditions, reducing the risk of introducing artifacts within the specimen. For all these reasons it could become a useful tool for quality control of the preservation process of osteochondral allografting in a bank of musculoskeletal tissues.

Construção de câmara de luz ultravioleta para fotopolimerização de fases estacionárias monolíticas

The assembly of a photochemical reactor with six fluorescent lamps, used for photopolymerizations is described. This chamber presents a mobile support, allowing the placement of samples at different heights and a safety lock that interrupts the radiation, if it is opened during operation. The mirrored internal walls avoid the dispersion and non-uniform distribution of light. There is no high heating because the own character of the used lamps. All parts could be purchased in commerce with less than U$ 150,00. This reactor was successfully used for monolithic stationary phase photopolymerization.

De los contenidos a las competencias numéricas en la enseñanza obligatoria = From contents to numerical competence in Compulsory Secondary Education

Mathematics has formed part of all our daily lives since the most remote origins of our civilization, although on too many occasions schools have done little for this functional view of mathematics reclaiming the formal role of this discipline in detriment of its more practical and applied element. From this perspective the curriculum organized by competence arises due to the need to fill this vacuum and allow our students to function better in the constant elements of real situations which they are going to have to resolve throughout their lives. The specifying of this general view of mathematic competence in the numeric competence should allow all our students to progressively acquire numeric sense, that is, that they have the capacity to apply good quantitative ideas in real situations