Simultaneous spectrophotometric determination of ezetimibe and simvastatin in pharmaceutical preparations using chemometric techniques

Two spectrophotometric methods are described for the simultaneous determination of ezetimibe (EZE) and simvastatin (SIM) in pharmaceutical preparations. The obtained data was evaluated by using two different chemometric techniques, Principal Component Regression (PCR) and Partial Least-Squares (PLS-1). In these techniques, the concentration data matrix was prepared by using the mixtures containing these drugs in methanol. The absorbance data matrix corresponding to the concentration data matrix was obtained by the measurements of absorbances in the range of 240 - 300 nm in the intervals with Δλ = 1 nm at 61 wavelengths in their zero order spectra, then, calibration or regression was obtained by using the absorbance data matrix and concentration data matrix for the prediction of the unknown concentrations of EZE and SIM in their mixture. The procedure did not require any separation step. The linear range was found to be 5 - 20 µg mL-1 for EZE and SIM in both methods. The accuracy and precision of the methods were assessed. These methods were successfully applied to a pharmaceutical preparation, tablet; and the results were compared with each other.

Thermal and structural study of guava (Psidium guajava L) powders obtained by two dehydration methods

Two food products (powders) were obtained by hot-air drying or lyophilisation methods on the whole guava fruits. The powders were characterised by sensory and thermal analyses (TGA-DSC), infrared spectroscopy (IR), X-ray diffraction (XRD) and scanning electron microscopy (SEM). Thermal, morphological and structural characterisations showed a similar behaviour for the two solids. TGA-DSC and IR showed the presence of pectin as the main constituent of solids. A semi-crystalline profile was evidenced by XRD, and lamellar/spherical morphologies were observed by SEM. Sensory analyses revealed an aroma highly related to guava. These value-added food products are an alternative to process guava and avoid loss during postharvest handling.

Partition of proteases from Lentinus citrinus DPUA 1535 by the Peg/Phosphate Aqueous Two-Phase System

A full two-level factorial design was employed to study the influence of PEG molar mass (MM PEG), PEG concentration (C PEG) and phosphate concentration (C PHOSPH) on proteases partition by Lentinus citrinus DPUA 1535 in a PEG/phosphate aqueous two-phase system (ATPS). For all ATPS studied, proteases partitioned for the top phase and the best proteases extraction condition was obtained with MM PEG = 6000 g mol-1, C PEG = 17.5% (w/w) and C PHOSPH = 25% (w/w) with (1.1) purification factor and (151%) activity yield. Findings reported here demonstrate a practical strategy that serves as a first step for proteases purification from crude extract by L. citrinus.

Small and Large Scale Dynamics in the Milky Way

This thesis contains dynamical analysis on four different scales: the Solar system, the Sun itself, the Solar neighbourhood, and the central region of the Milky Way galaxy. All of these topics have been handled through methods of potential theory and statistics. The central topic of the thesis is the orbits of stars in the Milky Way. An introduction into the general structure of the Milky Way is presented, with an emphasis on the evolution of the observed value for the scale-length of the Milky Way disc and the observations of two separate bars in the Milky Way. The basics of potential theory are also presented, as well as a developed potential model for the Milky Way. An implementation of the backwards restricted integration method is shown, rounding off the basic principles used in the dynamical studies of this thesis. The thesis looks at the orbit of the Sun, and its impact on the Oort cloud comets (Paper IV), showing that there is a clear link between these two dynamical systems. The statistical atypicalness of the orbit of the Sun is questioned (Paper I), concluding that there is some statistical typicalness to the orbit of the Sun, although it is not very significant. This does depend slightly on whether one includes a bar, or not, as a bar has a clear effect on the dynamical features seen in the Solar neighbourhood (Paper III). This method can be used to find the possible properties of a bar. Finally, we look at the effect of a bar on a statistical system in the Milky Way, seeing that there are not only interesting effects depending on the mass and size of the bar, but also how bars can capture disc stars (Paper II).

Key performance indicators for supplier and assortement evaluation

Tutkimuksen tavoite oli selvittää suorituskyvyn mittaamista, mittareita ja niiden suunnittelua tukku- ja jakeluliiketoiminnassa. Kriittisten menestystekijöiden mittarit auttavat yritystä kohti yhteistä päämäärää. Kriittisten menestystekijöiden mittarit ovat usein yhdistetty strategiseen suunnitteluun ja implementointiin ja niillä on yhtäläisyyksiä monien strategisten työkalujen kun Balanced scorecardin kanssa. Tutkimus ongelma voidaan esittää kysymyksen muodossa. •Mitkä ovat Oriola KD:n pitkänaikavälin tavoitteita tukevat kriittisten menestystekijöiden mittarit (KPIs) toimittajan ja tuotevalikoiman mittaamisessa? Tutkimus on jaettu kirjalliseen ja empiiriseen osaan. Kirjallisuus katsaus käsittelee aikaisempaa tutkimusta strategian, toimitusketjun hallinnan, toimittajan arvioinnin ja erilaisten suorituskyvyn mittaamisjärjestelmien osalta. Empiirinen osuus etenee nykytila-analyysista ehdotettuihin kriittisten menestystekijöiden mittareihin, jotka ovat kehitetty kirjallisuudesta löydetyn mallin avulla. Tutkimuksen lopputuloksena ovat case yrityksen tarpeisiin kehitetyt kriittisten menestystekijöiden mittarit toimittajan ja tuotevalikoiman arvioinnissa.

Induction Motor Drive Energy Efficiency - Simulation and Analysis

A coupled system simulator, based on analytical circuit equations and a finite element method (FEM) model of the motor has been developed and it is used to analyse a frequency-converterfed industrial squirrel-cage induction motor. Two control systems that emulate the behaviour of commercial direct-torque-controlled (DTC) and vector-controlled industrial frequency converters have been studied, implemented in the simulation software and verified by extensive laboratory tests. Numerous factors that affect the operation of a variable speed drive (VSD) and its energy efficiency have been investigated, and their significance in the simulation of the VSD results has been studied. The dependency of the frequency converter, induction motor and system losses on the switching frequency is investigated by simulations and measurements at different speeds for both the vector control and the DTC. Intensive laboratory measurements have been carried out to verify the simulation results.

Rasitusten älykäs seuranta

Tässä diplomityössä käsitellään monikappalesysteeminä mallinnetun toimilaitteen tai mekaanisen systeemin kappaleissa vaikuttavien rasitusten, siirtymien ja jännitysten laskentamenetelmiä. Työhön sisällytettyjen menetelmien valinta on toteutettu 2000-luvulla virtuaalisuunnittelua käsittelevissä tiedelehdissä julkaistujen artikkelien pohjalta. Työn tarkoituksena on muodostaa kirjallisuuskatsaus uusien laskentamenetelmien ominaisuuksista ja metodiikasta, mitä voidaan tarvittaessa soveltaa virtuaalisuunnittelun tarpeisiin. Kaksi esiteltävistä menetelmistä on optimointimenetelmiä (RBDO ja ESL). Muissa menetelmissä käsitellään muun muassa venymien rekonstruointia ja hankauskitkasta komponentteihin kohdistuvia jännityksiä. Moving frame-menetelmässä sovelletaan kelluvan koordinaatiston periaatetta, yksi menetelmistä perustuu selkeästi osarakennetekniikkaan ja yhdessä kappaleiden joustokäyttäytymistä mallinnetaan muotofunktioiden avulla. Lisäksi on kolme soveltavaa esimerkkiä rasitusten seurannasta teollisuuskoneissa. Laskentamenetelmät ovat luonteeltaan ja sovelluskelpoisuudeltaan erilaisia. Optimointimenetelmät ovat parhaimmillaan rakenteiden jatkokehitystyössä, siinä missä muut menetelmät soveltuvat joko olemassa olevien rakenteiden mallintamiseen tai kokonaan uusien systeemien suunnittelutyökaluiksi. Tätä eroavuutta voidaan pitää hyvänä asiana, jotta voidaan valita parhaiten omiin tarkoituksiin soveltuva menetelmä.

Communicative and Anticipatory Decision-Making Supported by Bayesian Networks

The purpose of this research is to draw up a clear construction of an anticipatory communicative decision-making process and a successful implementation of a Bayesian application that can be used as an anticipatory communicative decision-making support system. This study is a decision-oriented and constructive research project, and it includes examples of simulated situations. As a basis for further methodological discussion about different approaches to management research, in this research, a decision-oriented approach is used, which is based on mathematics and logic, and it is intended to develop problem solving methods. The approach is theoretical and characteristic of normative management science research. Also, the approach of this study is constructive. An essential part of the constructive approach is to tie the problem to its solution with theoretical knowledge. Firstly, the basic definitions and behaviours of an anticipatory management and managerial communication are provided. These descriptions include discussions of the research environment and formed management processes. These issues define and explain the background to further research. Secondly, it is processed to managerial communication and anticipatory decision-making based on preparation, problem solution, and solution search, which are also related to risk management analysis. After that, a solution to the decision-making support application is formed, using four different Bayesian methods, as follows: the Bayesian network, the influence diagram, the qualitative probabilistic network, and the time critical dynamic network. The purpose of the discussion is not to discuss different theories but to explain the theories which are being implemented. Finally, an application of Bayesian networks to the research problem is presented. The usefulness of the prepared model in examining a problem and the represented results of research is shown. The theoretical contribution includes definitions and a model of anticipatory decision-making. The main theoretical contribution of this study has been to develop a process for anticipatory decision-making that includes management with communication, problem-solving, and the improvement of knowledge. The practical contribution includes a Bayesian Decision Support Model, which is based on Bayesian influenced diagrams. The main contributions of this research are two developed processes, one for anticipatory decision-making, and the other to produce a model of a Bayesian network for anticipatory decision-making. In summary, this research contributes to decision-making support by being one of the few publicly available academic descriptions of the anticipatory decision support system, by representing a Bayesian model that is grounded on firm theoretical discussion, by publishing algorithms suitable for decision-making support, and by defining the idea of anticipatory decision-making for a parallel version. Finally, according to the results of research, an analysis of anticipatory management for planned decision-making is presented, which is based on observation of environment, analysis of weak signals, and alternatives to creative problem solving and communication.

Crop coefficient and water consumption of eggplant in no-tillage system and conventional soil preparation

Under organic management in Seropédica-RJ, Brazil, using a weighing lysimeter, the crop coefficients (kc), the maximum evapotranspiration and the productivity of eggplant cultivation under two cropping systems (no tillage with straw plus soil with conventional preparation) were determined. A whole randomized layout with two treatments (no tillage and conventional) and five replicates during 134 days of cultivation were adopted. There were no significant differences in the eggplant cultivation in the two cropping systems, with a maximum commercial productivity obtained from 47.42 Mg ha-1 for the no-tillage system, and 47.91 Mg ha-1 for the conventional tillage. The accumulated ETc was 285.15 and 323.44 mm for the no-tillage and conventional, respectively. The crop coefficients value for the phases: 1 - transplanting, flowering, 2 - flowering-fruiting, 3 - fruit- first harvesting, 4- first harvesting of the final crop cycle was 0.83, 0.77, 0.90 and 0.97 in no-tillage system for the respective phases and for the conventional one 0.81, 1.14, 1.17 and 1.05 for the same steps described above.

Energetic analysis of landrace varieties and hybrids of corn produced in different technological levels of management

The aim of this study was to analyze, under the energetic point of view, the cultivation of corn in three management systems (low, medium and high-tech), using two landrace varieties ('Argentino' and 'BR da Várzea'), a double hybrid cultivar (SHS 4080) and a simple hybrid (IAC 8333). Five performance indicators were used: energy efficiency, liquid cultural energy, cultural efficiency, energy balance and productive energy efficiency. From the perspective of family farming, it was verified the largest social importance of the systems under low and medium levels of technology, due to the increase employment capacity of rural labor. The liquid cultural energy and energy balance were more favorable for the system under high technological level, unlike cultural efficiency and productive energy efficiency, which were significantly higher for medium and low technological levels. The variety 'Argentino' showed lower productive energy efficiency. The variety 'BR da Várzea', on the other hand, presented the potential to generate energy as much as the hybrids. In general, the biggest sustainability in the corn crop was achieved when the management system under medium and lower levels of technology were used.

Initial development of two eucalyptus hybrid submitted to irrigation

The eucalyptus offers several advantages compared to other forestry species and, by using the irrigation can increase productivity and decrease production time. The objective of the present study was to evaluate two hybrid eucalyptus (Grancam and Urograndis), no irrigation, dripping and micro sprinkler irrigated at 90, 120, 150 and 180 days after transplanting (DAT). The experiment was conducted at the experimental irrigation area in the State University of Mato Grosso do Sul, in the municipality of Aquidauna - State of MS, Brazil. The experimental design was randomized blocks, split plot with four blocks and two replications within each block, and the plots were composed by irrigation treatments (dripping, micro sprinkler irrigate and dry) and the subplots the hybrids (Grancam and Urograndis).The total area of the experiment had 3 hectares, where each plot consisted of 1 ha. It was evaluated plant height, stem diameter and canopy, stem basal area, the relationship between height and stem diameter, the relationship between height and canopy diameter and stem volume. Data were subjected to analysis of variance and compared by Tukey test at 5% probability. Irrigation systems and dripping sprinkle provide greater plant height, stem diameter, canopy diameter, stem basal area and stem volume.

The impact of evaporative cooling on the thermoregulation and sensible heat loss of sows during farrowing

Pigs are more sensitive to high environmental temperatures explained by the inability of sweating and panting properly when compared to other species of farmed livestock. The evaporative cooling system might favor the thermal comfort of animals during exposure to extreme environmental heat and reduce the harmful effects of heat stress. The purpose of this study was to assess the sensible heat loss and thermoregulation parameters from lactating sows during summer submitted to two different acclimatization systems: natural and evaporative cooling. The experiment was carried out in a commercial farm with 72 lactating sows. The ambient variables (temperature, relative humidity and air velocity) and sows physiological parameters (rectal temperature, surface temperature and respiratory rate) were monitored and then the sensible heat loss at 21days lactation was calculated. The results of rectal temperature did not differ between treatments. However, the evaporative cooling led to a significant reduction in surface temperature and respiratory rate and a significant increase in the sow's sensible heat loss. It was concluded that the use of evaporative cooling system was essential to increase sensible heat loss; thus, it should reduce the negative effects of heat on the sows' thermoregulation during summer.

Concentration of injetion solution and its effects on soil and on yield of fertirrigated banana cv. Terra Maranhão

The Fertigation is the combined application of water and nutrients to a crop. It can be adapted to all types of agricultural crops. The objective of this study was to evaluate the effect of urea concentration in irrigation water on electrical conductivity of the soil solution and saturation extract along the first cycle of banana cv. Terra Maranhão. The experiment followed a completely randomized design with six treatments and ten replications. Treatments regarded for using three urea concentrations (1.0; 2.5 and 4.0 g L-1) in irrigation water applied by two micro irrigation systems (microsprinkler and drip). Results showed that there was a linear elevation of electrical conductivity of saturation extract and soil solution with the increase on concentration of urea in the injection solution. Urea should be used under concentrations up to 2.5 g L-1 in irrigation water without causing increase on electric conductivity of soil solution and saturation extract, considering 1.1 dS m-1 as the tolerated value for the crop. Nitrate in the soil solution increased significantly with the increase of urea concentration in the injection solution. The maximum concentration of nitrate in the soil occurred for 4,0 g L-1 concentration of the injection solution.

Comparison of Two- and Three-dimensional Ultrasonography in the Evaluation of Lesion Level in Fetuses with Spina Bifida

Purpose To evaluate the precision of both two- and three-dimensional ultrasonography in determining vertebral lesion level (the first open vertebra) in patients with spina bifida. Methods This was a prospective longitudinal study comprising of fetuses with open spina bifida who were treated in the fetal medicine division of the department of obstetrics of Hospital das Clínicas of the Universidade de São Paulo between 2004 and 2013. Vertebral lesion level was established by using both two- and three-dimensional ultrasonography in 50 fetuses (two examiners in each method). The lesion level in the neonatal period was established by radiological assessment of the spine. All pregnancies were followed in our hospital prenatally, and delivery was scheduled to allow immediate postnatal surgical correction. Results Two-dimensional sonography precisely estimated the spina bifida level in 53% of the cases. The estimate error was within one vertebra in 80% of the cases, in up to two vertebrae in 89%, and in up to three vertebrae in 100%, showing a good interobserver agreement. Three-dimensional ultrasonography precisely estimated the lesion level in 50% of the cases. The estimate error was within one vertebra in 82% of the cases, in up to two vertebrae in 90%, and in up to three vertebrae in 100%, also showing good interobserver agreement. Whenever an estimate error was observed, both two- and three-dimensional ultrasonography scans tended to underestimate the true lesion level (55.3% and 62% of the cases, respectively). Conclusions No relevant difference in diagnostic performance was observed between the two- and three-dimensional ultrasonography. The use of three-dimensional ultrasonography showed no additional benefit in diagnosing the lesion level in the fetuses with spina bifida. Errors in both methods showed a tendency to underestimate lesion level.

Collaborative information behaviour : a case study of two research groups

The aim of the licentiate thesis is to examine researchers' information practices in research groups. The researchers were involved with study communication and media related issues within Social Sciences and Humanities Faculties. The theoretical framework of the study comprises the new holistic models of information seeking (for example: Meho and Tibbo, 2003; Seldén, 1999) and the collective aspects of information behaviour (Prekop, 2002 ; Talja, 2002; Talja and Hansen, 2006). The research questions are: 1. How do scholars seek information in research groups? 2 What kind of collaborative information behaviour occurs in the research groups? The research data was gathered by interviews and observations. Three meetings of a research group at the University of Tampere were observed during the autumn of 2004. The group members and the group leader of the research group were interviewed in the spring of 2005. The research group members and the group leader of a research group at the University of Jyväskylä were interviewed in the autumn of 2005. Altogether, two research group leaders and eight researchers were interviewed. The significance of the research group for information seeking is more important in closeknit research groups than in rather loose research groups. The significance of the research group for information seeking can be at least threefold. First, research group members can inform the group about relevant information resources and potential library or other information services. Second, the research group can to some extent compensate for the information seeking systems of libraries by distributing material and information resources. Third, information seeking can be carried out in collaboration in research groups. The significance of the research group was found to be most important in informing about new information services and marketing library systems. Recommendations from colleagues were often needed to mobilize researchers into using new library services. The significance of colleagues in informing about library services is in line with earlier studies. The present study showed that sometimes information from colleagues was regarded as more important than information distributed directly by the local library. A culture of information sharing, including mutual trust, seemed mainly to be reflected in collaboration and collaborative information seeking in the research groups studied. The timing of the onset of individual research seemed to be related to the information sharing culture and social networks in research groups. The simultaneous onset of the research work by group members seemed to promote the growth of unbiased collaboration, also in information seeking.