Estudo do comportamento da sinterização de compactos de cavacos de um aço SAE 1050 obtidos sob alta pressão

From an economic standpoint, the powder metallurgy (P/M) is a technique widely used for the production of small parts. It is possible, through the P/M and prior comminution of solid waste such as ferrous chips, produce highly dense sintered parts and of interest to the automotive, electronics and aerospace industries. However, without prior comminution the chip, the production of bodies with a density equal to theoretical density by conventional sintering techniques require the use of additives or significantly higher temperatures than 1250ºC. An alternative route to the production of sintered bodies with high density compaction from ferrous chips (≤ 850 microns) and solid phase sintering is a compression technique under high pressure (HP). In this work, different compaction pressures to produce a sintered chip of SAE 1050 carbon steel were used. Specifically, the objective was to investigate them, the effect of high pressure compression in the behavior of densification of the sintered samples. Therefore, samples of the chips from the SAE 1050 carbon steel were uniaxially cold compacted at 500 and 2000 MPa, respectively. The green compacts obtained were sintered under carbon atmosphere at 1100 and 1200°C for 90 minutes. The heating rate used was 20°C/min. The starting materials and the sintered bodies were characterized by optical microscopy, SEM, XRD, density measurements (geometric: mass/volume, and pycnometry) and microhardness measurements Vickers and Rockwell hardness. The results showed that the compact produced under 2000 MPa presented relative density values between 93% and 100% of theoretical density and microhardness between 150 HV and 180 HV, respectively. In contrast, compressed under 500 MPa showed a very heterogeneous microstructure, density value below 80% of theoretical density and structural conditions of inadequate specimens for carrying out the hardness and microhardness measurements. The results indicate that use of the high pressure of ferrous chips compression is a promising route to improve the sinterability conditions of this type of material, because in addition to promoting greater compression of the starting material, the external tension acts together with surface tension, functioning as the motive power for sintering process. Additionally, extremely high pressures allow plastic deformation of the material, providing an intimate and extended contact of the particles and eliminating cracks and pores. This tends to reduce the time and / or temperature required for good sintering, avoiding excessive grain growth without the use of additives. Moreover, higher pressures lead to fracture the grains in fragile or ductile materials highly hardened, which provides a starting powder for sintering, thinner, without the risk of contamination present when previous methods are used comminution of the powder.

Uso de água produzida na formulação de fluidos de perfuração

Drilling fluids have fundamental importance in the petroleum activities, since they are responsible for remove the cuttings, maintain pressure and well stability, preventing collapse and inflow of fluid into the rock formation and maintain lubrication and cooling the drill. There are basically three types of drilling fluids: water-based, non-aqueous and aerated based. The water-based drilling fluid is widely used because it is less aggressive to the environment and provide excellent stability and inhibition (when the water based drilling fluid is a inhibition fluid), among other qualities. Produced water is generated simultaneously with oil during production and has high concentrations of metals and contaminants, so it’s necessary to treat for disposal this water. The produced water from the fields of Urucu-AM and Riacho da forquilha-RN have high concentrations of contaminants, metals and salts such as calcium and magnesium, complicating their treatment and disposal. Thus, the objective was to analyze the use of synthetic produced water with similar characteristics of produced water from Urucu-AM and Riacho da Forquilha-RN for formulate a water-based drilling mud, noting the influence of varying the concentration of calcium and magnesium into filtered and rheology tests. We conducted a simple 32 factorial experimental design for statistical modeling of data. The results showed that the varying concentrations of calcium and magnesium did not influence the rheology of the fluid, where in the plastic viscosity, apparent viscosity and the initial and final gels does not varied significantly. For the filtrate tests, calcium concentration in a linear fashion influenced chloride concentration, where when we have a higher concentration of calcium we have a higher the concentration of chloride in the filtrate. For the Urucu’s produced water based fluids, volume of filtrate was observed that the calcium concentration influences quadratically, this means that high calcium concentrations interfere with the power of the inhibitors used in the formulation of the filtered fluid. For Riacho’s produced water based fluid, Calcium’s influences is linear for volume of filtrate. The magnesium concentration was significant only for chloride concentration in a quadratic way just for Urucu’s produced water based fluids. The mud with maximum concentration of magnesium (9,411g/L), but minimal concentration of calcium (0,733g/L) showed good results. Therefore, a maximum water produced by magnesium concentration of 9,411g/L and the maximum calcium concentration of 0,733g/L can be used for formulating water-based drilling fluids, providing appropriate properties for this kind of fluid.

Caracterização de água de lavagem de filtros em estações de tratamento de água de filtração direta

The water supply and treatment is considered as a great benefit considering that, if done efficiently, provides public health. However, considering the WTP (Water Treatment Plant) is an industry, with its inputs and waste generation, they must be constantly evaluated and monitored to verify the best and most appropriate way to process and dispose their waste, minimizing therefore the potential impacts to the environment. By volume, the most significant waste is the rapid filter backwash water. It is very common the disposal of this waste without treatment in water sources, which are used, for the most part, as a water supply source of a downstream population. This study evaluated quantitative and qualitative parameters in filter backwash water in three WTP - Itaitinga, Maranguape and Pacatuba, located in Ceará State, northeast of Brazil. It was found that the Maranguape WTP, in terms of treatment capacity, is the larger. The Itaitinga WTP is the one that consumes more water during filters washing. The Pacatuba WTP exhibited higher concentration of total suspended and settleable solids, COD and aluminum in the filters backwash water. It is noteworthy that the settleable solids and total suspended solids in all three WTP are above the effluent discharge standard recommended by Resolution 154/2002 of SEMACE (State Superintendent of Environment of Ceará). It was concluded that the filter backwash water from the study WTP exceeded the allowed values for legislation to be disposed directly into surface water bodies. It is suggested as an alternative to treat and recycle the filter backwashing water the construction of sludge settling ponds.

Extensões multidimensionais para correntropia e suas aplicações em estimativas robustas

This present work uses a generalized similarity measure called correntropy to develop a new method to estimate a linear relation between variables given their samples. Towards this goal, the concept of correntropy is extended from two variables to any two vectors (even with different dimensions) using a statistical framework. With this multidimensionals extensions of Correntropy the regression problem can be formulated in a different manner by seeking the hyperplane that has maximum probability density with the target data. Experiments show that the new algorithm has a nice fixed point update for the parameters and robust performs in the presence of outlier noise.

Biolipídio B2: desenvolvimento de um veículo estável para reposição hormonal transdérmica nanoestruturada

The hormone administration by the oral route is frequently related with different many side effects. The aim of this study was to evaluate the safety and efficacy of a new product intended to transdermal hormone replacement nanostructured (TRHN) therapy, based on a patented under No. US 2013/0123220A1 formulation. This formulation was able to restore serum levels of estradiol (0.1%) + estradiol (0.25%) in 122 postmenopausal women with a mean age of 56.88 (± 6.27). The assessment is part of a longitudinal prospective study. Clinical parameters, including the degree of satisfaction with symptom relief, serum concentrations of estradiol, weight, blood pressure, were compared between the beginning and the end of treatment. The findings show that BIOLIPÍDEO B2® was safe and effective in restoring hormonal serum levels without side effects. The satisfaction with treatment was 92%. Serum concentrations of estradiol was significantly higher after treatment (p <0.05). Weight and systolic and diastolic blood pressure showed no significant differences (p> 0.05) during treatment. No vaginal bleeding was observed. Evaluation of bilateral breast mammography treatment found normal results in all women. This study shows for the first time the effectiveness of a transdermal formulation nanostructured in the transdermal delivery of estradiol and estriol measured in vivo using Confocal Raman Spectroscopy. The formulation of BIOLIPÍDEO/B2® is safe and effective in restoring serum estradiol levels and alleviates menopausal symptoms. The formulation can serve as a good choice for hormone replacement therapy to protect against post-menopausal symptoms.

Conservação de material genético de espécies silvestres do bioma caatinga utilizando a manipulação oócitos inclusos em folículos ovarianos pré antrais (MOIFOPA)

The objective of the present thesis was to use the manipulation of oocytes enclosed in preantral follicles (MOEPF) as a tool for the female gametes rescue and optimization, from wild species of Caatinga biome. The thesis was divided into 4 experiments. At first experiment, it was performed the estimative and description of the agouti (Dasyprocta leporina) preantral follicles (PF) histologic and ultrastructural features, in which it was estimated 4419.8 ± 532.26 and 5397.52 ± 574.91 follicles for the right and left ovary, respectively, and the majority (86,63%) belonged to the primordial follicles category (P<0.05). Most of the population consists of morphologically normal follicles (70.78%), presenting a large and central nuclei and uniform cytoplasm. At ultrastructural evaluation it was verified the presence of a great number of round mitochondrias associated to lipid droplets. In the second experiment, it was performed the estimative and description of yellow-toothed cavies (Galea spixii) PF characteristics, also, the evaluation of the effect of solid surface vitrification (SSV) on the in situ PF morphology. The total of 416.0 ± 342.8 PF was estimated for the ovary pair and the presence of a large quantity of primary follicles (P<0.05) was evidenced. Most of the PF was morphologically normal (94.6%), in which the oocyte nuclei presented condensed granules of heterochromatin. Round or elongated shaped mitochondria constituted the most abundant organelles. In regard of the SSV, the protocol using the dimethylsulfoxide (DMSO) 3M possibility the preservation of 69.5% of morphologically normal PF, which was evidenced by the light and transmission electronic microscopy. At third experiment, the evaluation of the SSV procedure on the morphology and viability in situ PF form collared peccaries (Pecari tajacu) was performed. No differences were observed among treatments, in which the use of DMSO, ethylene glycol (EG) and dimethylformamide (DMF) as cryoprotectants, regardless its concentration, promoted the morphology preservation of much than 70% of PF. Concerning the PF viability, the DMSO and EG promoted the best preservation. The fourth experiment aimed to evaluate the effect of α MEM+ or TCM199 associated or not to 50 ng of FSHr on the morphology, activation and growth of collared peccaries PF, in vitro cultured (IVC) during 1 or 7 days and the effect on the extracellular matrix (ECM). After 7 days of IVC only the use of TCM199/FSH maintained the proportion of intact PF, similar to day 1(63.2%), however, no differences were observed among treatments (P>0.05). Also, an improvement of the proportion of intact growing PF was verified (P>0.05). By the Ag-NOR analysis it was observed that only the treatment using TCM199/FSH promoted the maintenance of cell proliferation similar to day 1 (P>0.05). The picrosirius red stain revealed that ECM remained intact in all treatments (P>0.05). Thus, as the general conclusion, the use of MOEPF in the refereed species allowed the knowledge of aspects related to its reproductive morphology and physiology, enabling the germplasm conservation, with the possibility of germplasm bank formation, as the elucidation of mechanisms related to the PF survive and in vitro development.

Obtenção e conservação de espermatozoides de cutia (Dasyprocta leporina Linneaus, 1753) do semiárido brasileiro

The general objective of this thesis was to stablish protocols to obtain and conserve agouti (Dasyprocta leporina) sperm bred in captivity in the Brazilian semi-arid, aiming its sustainable production. The thesis was divided in three experiments. In the first one, we studied the influence of the interaction between two probes (quadratics and sine waves) and two stimulation protocols (continuous and in series) on the agouti sperm collection by electroejaculation efficiency. The most efficient interaction on this obtainment was the one with probes with rings associated with stimuli in series (4/7; 57%, P<0.05). In the second experiment we compared the cryoprotectant effects of different substances (glycerol, ethyleneglycol, dimethylsulfoxide, dimethylformamide) on epididymis sperm cryopreservation. The highest values on motility (39.5±4.6%), vigor (2.9±0.2) and membrane integrity (30.6±4.5%) were observed on the samples cryopreserved using glycerol when compared to those with ethyleneglycol and dimethylformamide, but there was no difference (P>0.05) when compared to the samples cryopreserved with dimethylsulfoxide. At last, we studied the effects of the methods to obtain sperm (electroejaculation vs epididymal collection) on post thawing sperm quality. The samples obtained by epididymal retrograde flushing showed values for motility of 25.0±10.9% and vigor 2.4±0.8, and those obtained by electroejaculation had 31.2±14.2% of motility and vigor of 2.2±0.7, however, without statistical difference (P>0.05), which shows the possibility to successfully use the epididymal sperm cryopreservation protocol on agouti ejaculated sperm. In conclusion, significant advances on obtainment and processing of agouti sperm were made, allowing the establishment of germplasm banks from sperm samples obtained from the epididymis or by electroejaculation.

For the win (FTW)! Contribuições de um serious game para o ensino-aprendizagem de argumentação

This is a qualitative and reflexive research with focus on digital literacy. Among the digital media that could support the teaching of argumentation in the Science & Technology and Information Technology undergraduate courses of the Federal University of Rio Grande do Norte, we chose a serious game as object of research. Given the object of study in the discipline of reading and writing II – argumentation and genre from the order of argumentative writing -, common to the undergraduate courses mentioned, we invest on the development of a serious game, named ArgumentACTION, because we believe that it may, in fact, become a promising didactic instrument. Therefore we intend to understand whether and how this game can help students develop their reading and writing skills more independently, specifically towards an argumentative order genre: the opinion piece. With this research, we intend to contribute to the teaching of the Portuguese language on three bases: extending theoretical scope, in order to generate greater intelligibility on the teaching-learning process of argumenting; proposing a new methodological possibility, with the incorporation of a serious games to teaching; perfecting the game with which we are working, in order to build – and make available – a more refined digital tool to subsidize the teaching and learning of reading and writing of opinion pieces. To do so, we use the following as theoretical-methodological: Studies of Literacy (KLEIMAN, 2012b; TINOCO, 2008; OLIVEIRA, 2010; GEE, 2009; 2010; ROJO, 2012), The Applied Linguistics (KLEIMAN, 1998; BUSH-LEE, 2009), The Philosophy of Language (BAKHTIN, VOLOSHINOV, 2012) and Critical Pedagogy (DEWEY, 2010). A group of students from the upper mentioned undergraduate courses collaborated with this research by playing and analyzing the game. They were also interviewed about their experience in this matter. From the data generated, we established the categories of analysis: decollection, interest, multimodality/multisemiosis and interactivity, agent of literacy, learning principles. The conclusions we obtained show that the investment in applications, especially games, can bring real benefits to the teaching/learning of the Portuguese language; moreover they reveal that the work on argumenting has much to gain with the incorporation of serious games; however the possible advantages depend on a focused teaching practice and constant improvements and updates of this type of interactive tool, as well as the pedagogical practice from those who use and develop the games.

Sistema detector de vazamentos em instalações prediais de água fria

Building installations of cold water are key parts in any model of housing, are homes or condos. However, these systems are subject to failure, which can range from a leak in a device until faults in the structure of water reservoirs and distribution system. These faults are responsible for great economic and environmental costs. In order to reduce these losses, this work proposes the development of a system able to detect the presence and identify some types of water leaks that may occur. For implementation and testing, consumption model was used in a simulator capable of reproducing a similar behavior to a real model and its consequent failures. The detection of leaks is done based on an expert like model having two detection modules, one active and one passive, which use an array of sensors and actuators (valves) to do the sensing. For testing and implementation has been developed a software capable of coupling the system simulator and detector. From the results it can be seen that the system proposed in this work, as well as functioning satisfactorily, can be easily implemented in microcontrollers or embedded systems due to its simplicity.

Um algoritmo paralelo eficiente de migração reversa no tempo (rtm) 3d com granularidade fina

The reverse time migration algorithm (RTM) has been widely used in the seismic industry to generate images of the underground and thus reduce the risk of oil and gas exploration. Its widespread use is due to its high quality in underground imaging. The RTM is also known for its high computational cost. Therefore, parallel computing techniques have been used in their implementations. In general, parallel approaches for RTM use a coarse granularity by distributing the processing of a subset of seismic shots among nodes of distributed systems. Parallel approaches with coarse granularity for RTM have been shown to be very efficient since the processing of each seismic shot can be performed independently. For this reason, RTM algorithm performance can be considerably improved by using a parallel approach with finer granularity for the processing assigned to each node. This work presents an efficient parallel algorithm for 3D reverse time migration with fine granularity using OpenMP. The propagation algorithm of 3D acoustic wave makes up much of the RTM. Different load balancing were analyzed in order to minimize possible losses parallel performance at this stage. The results served as a basis for the implementation of other phases RTM: backpropagation and imaging condition. The proposed algorithm was tested with synthetic data representing some of the possible underground structures. Metrics such as speedup and efficiency were used to analyze its parallel performance. The migrated sections show that the algorithm obtained satisfactory performance in identifying subsurface structures. As for the parallel performance, the analysis clearly demonstrate the scalability of the algorithm achieving a speedup of 22.46 for the propagation of the wave and 16.95 for the RTM, both with 24 threads.

Desenvolvimento e avaliação tribológica de emulsão O/A a partir de óleo vegetal epoxidado para aplicação em fluídos de corte

The cutting fluids are lubricants used in machining processes, because they present many benefits for different processes. They have many functions, such as lubrication, cooling, improvement in surface finishing, besides they decreases the tool wear and protect it against corrosion. Therefore due to new environment laws and demand to green products, new cutting fluids must be development. These shall be biodegradable, non-toxic, safety for environment and operator healthy. Thus, vegetable oils are a good option to solve this problem, replacing the mineral oils. In this context, this work aimed to develop an emulsion cutting fluid from epoxidized vegetable oil, promoting better lubrication and cooling in machining processes, besides being environment friendly. The methodology was divided in five steps: first one was the biolubricant synthesis by epoxidation reaction. Following this, the biolubricant was characterized in terms of density, acidity, iodo index, oxirane index, viscosity, thermal stability and chemical composition. The third step was to develop an emulsion O/A with different oil concentration (10, 20 and 25%) and surfactant concentration (1, 2.5 and 5%). Also, emulsion stability was studied. The emulsion tribological performance were carried out in HFRR (High Frequency Reciprocating Rig), it consists in ball-disc contact. Results showed that the vegetable based lubricant may be synthesized by epoxidationreaction, the spectra showed that there was 100% conversion of the epoxy rings unsaturations. In regard the tribological assessment is observed that the percentage of oil present in the emulsion directly influenced the film formation and coefficient of friction for higher concentrations the film formation process is slow and unstable, and the coefficient of friction. The high concentrations of surfactants have not improved the emulsions tribological performance. The best performance in friction reduction was observed to emulsion with 10% of oil and 5% of surfactant, its average wear scar was 202 μm.

Avaliação da conformidade dos blocos cerâmicos produzidos em algumas cerâmicas no Rio Grande do Norte

The final quality of the works accomplished by the building construction industry depends directly on the quality of the materials supplied and used during all their phases of execution. The federal government participation and several state programs have established conditions to stimulate and require the increment of the quality level in the building construction industry´s product chain. These programs aim at the product conformity to the technical standards. Within this context, the evaluation program of the ceramic product conformity in Rio Grande do Norte state is assessing the conformity degree to Brazilian Technical Standards of ceramic bricks and tiles made in the ceramic production area in the state. In this work, is determine the degree of conformity of the sealing ceramic bricks made by some companies in different areas of the state, such as Assú, São Gonçalo do Amarante, Apodi, Parelhas, São José do Mipibu e Macaíba. Using the technical standards as a point of reference, we attempted to reproduce in the laboratory the experimental procedures to the analysis execution, according to the specifications. It was possible to determine that none of the evaluated samples are in strict conformity with the current technical standards, what reflects the real situation of the products available on the market.

Produção e análise do desempenho óptico e elétrico de filmes finos de SnO2:F para aplicações fotovoltaicas

Conselho Nacional de Desenvolvimento Científico e Tecnológico - CNPq

A utilização da pesquisa operacional para o gerenciamento dos leitos em um hospital particular: estudo de caso baseado em simulação computacional

The hospital is a place of complex actions, where several activities for serving the population are performed such as: medical appointments, exams, surgeries, emergency care, admission in wards and ICUs. These activities are mixed with anxiety, impatience, despair and distress of patients and their families, issues involving emotional balance both for professionals who provide services for them as for people cared by them. The healthcare crisis in Brazil is getting worse every year and today, constitutes a major problem for private hospitals. The patient that comes to emergencies progressively increase, and in contrast, there is no supply of hospital beds in the same proportion, causing overcrowding, declines in the quality of care delivered to patients, drain of professionals of the health area and difficulty in management the beds. This work presents a study that seeks to create an alternative tool that can contribute to the management of a private hospital beds. It also seeks to identify potential issues or deficiencies and therefore make changes in flow for an increase in service capacity, thus reducing costs without compromising the quality of services provided. The tool used was the Computational Simulation –based in discrete event, which aims to identify the main parameters to be considered for a proper modeling of this system. This study took as reference the admission of a private hospital, based on the current scenario, where your apartments are in saturation level as its occupancy rate. The relocation of project beds aims to meet the growing demand for surgeries and hospital admissions observed by the current administration.

Identificação das políticas de incentivo ao desenvolvimento da energia eólica no Rio Grande do Norte (RN)

Energy is a vital resource for social and economic development. In the present scenario, the search for alternative energy sources has become fundamental, especially after the oil crises between 1973 and 1979, the Chernobyl nuclear accident in 1986 and the Kyoto Protocol in 1997. The demand for the development of new alternative energy sources aims to complement existing forms allows to meet the demand for energy consumption with greater security. Brazil, with the guideline of not dirtying the energy matrix by the fossil fuels exploitation and the recent energy crisis caused by the lack of rains, directs energy policies for the development of other renewable energy sources, complementing the hydric. This country is one of the countries that stand out for power generation capacity from the winds in several areas, especially Rio Grande do Norte (RN), which is one of the states with highest installed power and great potential to be explored. In this context arises the purpose of this work to identify the incentive to develop policies of wind energy in Rio Grande do Norte. The study was conducted by a qualitative methodology of data analysis called content analysis, oriented for towards message characteristics, its informational value, the words, arguments and ideas expressed in it, constituting a thematic analysis. To collect the data interviews were conducted with managers of major organizations related to wind energy in Brazil and in the state of Rio Grande do Norte. The identification of incentive policies was achieved in three stages: the first seeking incentives policies in national terms, which are applied to all states, the second with the questionnaire application and the third to research and data collection for the development of the installed power of the RN as compared to other states. At the end, the results demonstrated hat in Rio Grande do Norte state there is no incentive policy for the development of wind power set and consolidated, specific actions in order to optimize the bureaucratic issues related to wind farms, especially on environmental issues. The absence of this policy hinders the development of wind energy RN, considering result in reduced competitiveness and performance in recent energy auctions. Among the perceived obstacles include the lack of hand labor sufficient to achieve the reporting and analysis of environmental licenses, the lack of updating the wind Atlas of the state, a shortfall of tax incentives. Added to these difficulties excel barriers in infrastructure and logistics, with the lack of a suitable port for large loads and the need for reform, maintenance and duplication of roads and highways that are still loss-making. It is suggested as future work the relationship of the technology park of energy and the development of wind power in the state, the influence of the technology park to attract businesses and industries in the wind sector to settle in RN and a comparison of incentive policies to development of wind energy in the Brazilian states observing wind development in the same states under study.