Microgeneration of electricity with producer gas in dual fuel mode operation

Among the alternatives to meet the increasing of world demand for energy, the use of biomass as energy source is one of the most promising as it contributes to reducing emissions of carbon dioxide in the atmosphere. Gasification is a technological process of biomass energy production of a gaseous biofuel. The fuel gas has a low calorific value that can be used in Diesel engine in dual mode for power generation in isolated communities. This study aimed to evaluate the reduction in the consumption of oil Diesel an engine generator, using gas from gasification of wood. The engine generator brand used was a BRANCO, with direct injection power of 7.36 kW (10 HP) coupled to an electric generator 5.5 kW. Diesel oil mixed with intake air was injected, as the oil was injected via an injector of the engine (dual mode). The fuel gas was produced in a downdraft gasifier. The engine generator was put on load system from 0.5 kW to 3.5 kW through a set of electrical resistances. Diesel oil consumption was measured with a precision scale. It was concluded that the engine converted to dual mode when using the gas for the gasification of wood decreased Diesel consumption by up to 57%.

Design of Pulsed Electroacoustic Measurement System for Space Charge Characterisation

Pulsed electroacoustic (PEA) method is a commonly used non-destructive technique for investigating space charges. It has been developed since early 1980s. These days there is continuing interest for better understanding of the influence of space charge on the reliability of solid electrical insulation under high electric field. The PEA method is widely used for space charge profiling for its robust and relatively inexpensive features. The PEA technique relies on a voltage impulse used to temporarily disturb the space charge equilibrium in a dielectric. The acoustic wave is generated by charge movement in the sample and detected by means of a piezoelectric film. The spatial distribution of the space charge is contained within the detected signal. The principle of such a system is already well established, and several kinds of setups have been constructed for different measurement needs. This thesis presents the design of a PEA measurement system as a systems engineering project. The operating principle and some recent developments are summarised. The steps of electrical and mechanical design of the instrument are discussed. A common procedure for measuring space charges is explained and applied to verify the functionality of the system. The measurement system is provided as an additional basic research tool for the Corporate Research Centre of ABB (China) Ltd. It can be used to characterise flat samples with thickness of 0.2–0.5 mm under DC stress. The spatial resolution of the measurement is 20 μm.

Tumor do apêndice vermiforme

Appendiceal tumors are rare and usually presented as acute appendicitis. They are incidentally discovered at an emergency surgery, in which case the decision-making is very difficult. The purpose of this report is discuss to the most appropriate management for appendiceal tumors. A retrospective analysis of one case treated at HU-UEL was undertaken and the literature was reviewed. The conclusion is that frozen section should be done whenever the appendiceal findings are atypical. For appendiceal carcinoids greater than 2 cm and adenocarcinomas, a right hemicolectomy is recommended. Appendectomy is apropriate for patients whose carcinoid tumors are 1 cm in diameter or less and for carcinoid tumors between 1 cm and 2 cm without extensive lymphatic permeation and mesenteric invasion. Every case should be searched for synchronous tumors.

Building object-oriented software with the D-Bus messaging system

Object-oriented programming is a widely adopted paradigm for desktop software development. This paradigm partitions software into separate entities, objects, which consist of data and related procedures used to modify and inspect it. The paradigm has evolved during the last few decades to emphasize decoupling between object implementations, via means such as explicit interface inheritance and event-based implicit invocation. Inter-process communication (IPC) technologies allow applications to interact with each other. This enables making software distributed across multiple processes, resulting in a modular architecture with benefits in resource sharing, robustness, code reuse and security. The support for object-oriented programming concepts varies between IPC systems. This thesis is focused on the D-Bus system, which has recently gained a lot of users, but is still scantily researched. D-Bus has support for asynchronous remote procedure calls with return values and a content-based publish/subscribe event delivery mechanism. In this thesis, several patterns for method invocation in D-Bus and similar systems are compared. The patterns that simulate synchronous local calls are shown to be dangerous. Later, we present a state-caching proxy construct, which avoids the complexity of properly asynchronous calls for object inspection. The proxy and certain supplementary constructs are presented conceptually as generic object-oriented design patterns. The e ect of these patterns on non-functional qualities of software, such as complexity, performance and power consumption, is reasoned about based on the properties of the D-Bus system. The use of the patterns reduces complexity, but maintains the other qualities at a good level. Finally, we present currently existing means of specifying D-Bus object interfaces for the purposes of code and documentation generation. The interface description language used by the Telepathy modular IM/VoIP framework is found to be an useful extension of the basic D-Bus introspection format.

Project Master Document adaption in order fulfillment process

This thesis discusses adaption of new project management tool at ABB Oy Motors and Generators business unit, Synchronous Machines profit centre. Thesis studies project modeling in general and buries in the Gate Model used at ABB Synchronous Machines. It is essential to understand Gate Model because this new project management tool, called Project Master Document, is created on the base of the existing project model. Thesis also analyzes goals and structure of Project Master Document in order to ease implementation of this new tool. Project Master Document aims to improved customer order fulfillment by clearing order handover interface. Office process, especially responsibilities and target dates, become also clearer after Master Document implementation. The document is built to be frame for whole order fulfillment process including check points for each gate of project model and updated memos from all project meetings. Furthermore, project progress will be clearly stated by status markings and visualized with colors.

Exploration and Design of Power-Efficient Networked Many-Core Systems

Multiprocessing is a promising solution to meet the requirements of near future applications. To get full benefit from parallel processing, a manycore system needs efficient, on-chip communication architecture. Networkon- Chip (NoC) is a general purpose communication concept that offers highthroughput, reduced power consumption, and keeps complexity in check by a regular composition of basic building blocks. This thesis presents power efficient communication approaches for networked many-core systems. We address a range of issues being important for designing power-efficient manycore systems at two different levels: the network-level and the router-level. From the network-level point of view, exploiting state-of-the-art concepts such as Globally Asynchronous Locally Synchronous (GALS), Voltage/ Frequency Island (VFI), and 3D Networks-on-Chip approaches may be a solution to the excessive power consumption demanded by today’s and future many-core systems. To this end, a low-cost 3D NoC architecture, based on high-speed GALS-based vertical channels, is proposed to mitigate high peak temperatures, power densities, and area footprints of vertical interconnects in 3D ICs. To further exploit the beneficial feature of a negligible inter-layer distance of 3D ICs, we propose a novel hybridization scheme for inter-layer communication. In addition, an efficient adaptive routing algorithm is presented which enables congestion-aware and reliable communication for the hybridized NoC architecture. An integrated monitoring and management platform on top of this architecture is also developed in order to implement more scalable power optimization techniques. From the router-level perspective, four design styles for implementing power-efficient reconfigurable interfaces in VFI-based NoC systems are proposed. To enhance the utilization of virtual channel buffers and to manage their power consumption, a partial virtual channel sharing method for NoC routers is devised and implemented. Extensive experiments with synthetic and real benchmarks show significant power savings and mitigated hotspots with similar performance compared to latest NoC architectures. The thesis concludes that careful codesigned elements from different network levels enable considerable power savings for many-core systems.

Väsymiskestävyyden määritys murtumismekaanisilla särönmallinnusohjelmilla

Tässä työssä tutkitaan Wärtsilä Oyj:n moottorin ja ABB Oy:n generaattorin muodostaman aggregaatin väsymiskestävyyttä lineaarisen murtumismekaniikan avulla. Työn tavoitteena on selvittää ABAQUS/XFEM- ja FRANC3D-ohjelman soveltuvuus kuormitukseltaan ja geometrialtaan vaativan generaattorirungon suunnittelutyökaluksi. Generaattorirungon kuormitukset aiheutuvat aggregaatin käynnin sekä käynnistys- ja sammutusvaiheen aikai-sista syntyvistä värähtelyistä. Tutkimuksessa tarkastellaan generaattorirungon väsymistä käynninaikaisella kuormituksella. Työssä mallinnettiin generaattorirungosta valittu hitsausdetalji alimallinnustekniikalla, jolloin alimallin reunaehdot voitiin määrittää aggregaatille tehdyn vastelaskennan perus-teella. Alimallista tutkittiin kahta erilaista hitsiliitostyyppiä, joihin mallinnettiin XFEM- ja FRANC3D-ohjelmilla erikokoisia säröjä hitsiliitosten rajaviivalle sekä juuren puolelle. Tutkittavilla ohjelmilla saatujen jännitysintensiteettikertoimien avulla säröille voitiin las-kea ekvivalentti jännitysintensiteettikerroin, jota verrattiin kokeellisesti saatuun jännitysin-tensiteettikertoimen kynnysarvoon. XFEM- ja FRANC3D-ohjelmia vertailtiin käytön helppouden, tulosten tarkkuuden sekä laskenta-aikojen perusteella. Käytettävyyden ja laskenta-aikojen perusteella XFEM-ohjelma soveltui paremmin käytettäväksi teollisuudessa suunnittelu- ja kehitystyön apu-työkaluna. FRANC3D taas antoi XFEM-ohjelmaa luotettavampia tuloksia, mutta laskenta-ajat olivat moninkertaiset.

Sähkögeneraattoriosien hitsauksen tuottavuuden kehittäminen

Hitsauksen tuottavuuteen vaikuttavat hitsausmäärä, käytetyt prosessit ja laatu. Työn teoriaosuudessa tutustutaan hitsauksen tuottavuuteen sekä suunnittelullisesta että valmistuksellisesta näkökulmasta. Hitsauksen laadulliset asiat, kuten laatustandardit ja vaatimukset käydään läpi keskittyen standardin SFS-EN ISO 3834 kattaviin laatuvaatimuksiin. Rikkomaton ja rikkova aineenkoetus ja yleisimmät hitsausvirheet esitetään yleisellä tasolla. Hitsausprosesseista esitetään MIG/MAG- ja MAG-täytelankahitsauksen sekä pulssihitsauksen perusteet. Tässä diplomityössä tutkitaan pulssihitsauksen soveltuvuutta sähkögeneraattorin staattoripaketin eripariliitoksen hitsaukseen ja kykyä parantaa sekä tuottavuutta että laatua. Tutkimus perustuu koehitsauksiin ja niiden perusteella tehtyihin johtopäätöksiin. Lisäksi pohditaan sisätuulettimien hitsauksen kehittämistä ja annetaan kehitysehdotus valmistusprosessista. Koehitsauksien perusteella pulssihitsaus on hyvä prosessiparannus staattoripakettien hitsaukseen. Kohdistettu valokaari ja alhaisempi lämmöntuonti verrattuna perinteiseen MAG-hitsaukseen sekä hitsauksen yksinkertaisuus tuovat etuja eripariliitoksen hitsauksen laatuun. Kustannuslaskelmien myötä hitsausprosessin muutoksen odotetaan tuovan kustannussäästöjä. Hitsauslaadun parantuessa ja jälkityöstön määrän vähentyessä hitsausprosessin muutos on kannattava.

Taajuusmuuttajaohjattu kestomagneettitahtikone opetuslaboratoriokäytössä

Kestomagneettien kehittyminen on mahdollistanut sähkökoneen rakentamisen perinteisistä menetelmistä poiketen ja on samalla luonut uudenlaisia ominaisuuksia ja käyttökohteita. Erityisesti kestomagneettitahtikone (PMSM) on kasvattanut suosiota hyvän hyötysuhteen ja luotettavuuden myötä. Työssä esitellään kestomagneettitahtikonetta sen rakenteen ja toimintaperiaatteen avulla. Tarkastellaan kestomagneettien kehitystä ja tulevaisuuden näkymiä. Perehdytään myös taajuusmuuttajaan, mitä käytetään yleensä kestomagneettitahtikoneen ohjaukseen. Lisäksi esitetään taajuusmuuttajan erilaisia säätötapoja. Työn kokeellisessa osuudessa yliopiston opetuslaboratorioon kehitetään koneikko, jonka avulla tutkitaan kestomagneettitahtikoneen toimintaan osana sähkökäyttöä. Työn tavoitteena on selvittää PMSM:n ominaisuuksia sekä suunnitella sähkötekniikan työkurssille soveltuva mittaussarja, mikä johdattaa opiskelijat tässä työssä käsiteltyihin aihealueisiin.

Sähköavusteisen polkupyörän energian talteenotto lineaarigeneraattorilla

Sähköavusteisten polkupyörien määrä on kasvussa. Kasvua hidastavana tekijänä voidaan pitää niiden keskimäärin yli 1000 euron hintaa, josta suurin osa johtuu akustosta. Tämän työn tarkoituksena on selvittää lineaarigeneraattorin hyödynnettävyyttä sähköavusteisissa polkupyörissä. Lisäksi työssä kuvataan vaiheittain prototyypin suunnittelu ja rakentaminen. Mikäli lineaarigeneraattori-avusteisella sähköpolkupyörällä saavutetaan huomattava pidennys toimintamatkaan, voidaan pyörät varustaa halvemmilla ja kapasiteetiltään pienemmillä akuilla. Lineaarigeneraattorin hankintaa kannustaisi se, että se maksaisi vähemmän kuin vaihto suurempikapasiteettiseen akustoon.

Identification of Some Additional Loss Components in High-Power Low-Voltage Permanent Magnet Generators

Permanent magnet generators (PMG) represent the cutting edge technology in modern wind mills. The efficiency remains high (over 90%) at partial loads. To improve the machine efficiency even further, every aspect of machine losses has to be analyzed. Additional losses are often given as a certain percentage without providing any detailed information about the actual calculation process; meanwhile, there are many design-dependent losses that have an effect on the total amount of additional losses and that have to be taken into consideration. Additional losses are most often eddy current losses in different parts of the machine. These losses are usually difficult to calculate in the design process. In this doctoral thesis, some additional losses are identified and modeled. Further, suggestions on how to minimize the losses are given. Iron losses can differ significantly between the measured no-load values and the loss values under load. In addition, with embedded magnet rotors, the quadrature-axis armature reaction adds losses to the stator iron by manipulating the harmonic content of the flux. It was, therefore, re-evaluated that in salient pole machines, to minimize the losses and the loss difference between the no-load and load operation, the flux density has to be kept below 1.5 T in the stator yoke, which is the traditional guideline for machine designers. Eddy current losses may occur in the end-winding area and in the support structure of the machine, that is, in the finger plate and the clamping ring. With construction steel, these losses account for 0.08% of the input power of the machine. These losses can be reduced almost to zero by using nonmagnetic stainless steel. In addition, the machine housing may be subjected to eddy current losses if the flux density exceeds 1.5 T in the stator yoke. Winding losses can rise rapidly when high frequencies and 10–15 mm high conductors are used. In general, minimizing the winding losses is simple. For example, it can be done by dividing the conductor into transposed subconductors. However, this comes with the expense of an increase in the DC resistance. In the doctoral thesis, a new method is presented to minimize the winding losses by applying a litz wire with noninsulated strands. The construction is the same as in a normal litz wire but the insulation between the subconductors has been left out. The idea is that the connection is kept weak to prevent harmful eddy currents from flowing. Moreover, the analytical solution for calculating the AC resistance factor of the litz-wire is supplemented by including an end-winding resistance in the analytical solution. A simple measurement device is developed to measure the AC resistance in the windings. In the case of a litz-wire with originally noninsulated strands, vacuum pressure impregnation (VPI) is used to insulate the subconductors. In one of the two cases studied, the VPI affected the AC resistance factor, but in the other case, it did not have any effect. However, more research is needed to determine the effect of the VPI on litz-wire with noninsulated strands. An empirical model is developed to calculate the AC resistance factor of a single-layer formwound winding. The model includes the end-winding length and the number of strands and turns. The end winding includes the circulating current (eddy currents that are traveling through the whole winding between parallel strands) and the main current. The end-winding length also affects the total AC resistance factor.

The Role of a firm’s mindset in international success - case study of Finnish marine industry firms

This thesis investigates the influence of a firm’s mindset on international success in the context of the Finnish marine industry. The study draws theoretical wisdom from organisational behaviour and strategic management literatures. The research aim set for this study was to identify and categorise existing strategic types based on mindsets found in the marine industry SMEs, and to link the influence of mindsets with success by examining the role of mindsets in a firm’s performance. Mindsets of firms were conceptualised as aggregate collections of perceptions that influence how the surrounding environment is discerned by the members of the firm. Mindsets are idiosyncratic to firms and therefore important firm-specific resources which influence decision-making and can be observed through the strategic behaviour of firms. Qualitative case study method was applied which was further supported by quantitative data on the financial performance of the ten case firms. Taxonomy based on the dimension of mindsets and prediction was developed to demonstrate four ideal types of firms identified within the marine industry. It was found that all of the case firms emphasised adaptation in their strategy while planning was emphasised to a varying degree. Moreover, two different methods of adapting were found; proactive and reactive. Firms which plan in the long-term and adapt proactively constantly investigate whether their plans are synchronous with the realities of the market; by having an open mindset, a firm’s perception of the reality of the market is enabling the firm to develop value creating strategies which are superiorly informed.This finding was supported by the financial data and led to the proposition that having an open mindset and placing a high level of emphasis on prediction may have a positive influence on international success. Also, it was proposed that concentrating only on exploiting business opportunities in the present time and not exploring any addition opportunities can have a negative influence on the firm’s performance, even if the mindset of the firm is open.

Proposal of methodology for the modeling and control of manipulators

Industrial applications demand that robots operate in agreement with the position and orientation of their end effector. It is necessary to solve the kinematics inverse problem. This allows the displacement of the joints of the manipulator to be determined, to accomplish a given objective. Complete studies of dynamical control of joint robotics are also necessary. Initially, this article focuses on the implementation of numerical algorithms for the solution of the kinematics inverse problem and the modeling and simulation of dynamic systems. This is done using real time implementation. The modeling and simulation of dynamic systems are performed emphasizing off-line programming. In sequence, a complete study of the control strategies is carried out through the study of several elements of a robotic joint, such as: DC motor, inertia, and gearbox. Finally a trajectory generator, used as input for a generic group of joints, is developed and a proposal of the controller's implementation of joints, using EPLD development system, is presented.

Soodakattilalaitosten energiantuotannon lisääminen

The aim of this thesis is to study different methods to increase the energy production of recovery boilers. This improvement is encouraged by the current energy policy and the rapid rise in energy prices, especially in electricity. In addition, the energy efficiency of the power plants is intended to be improved. There are several methods to increase the energy production. The methods taken into more accurate study are lower pressure steam for soot blowing and flue gas coolers. Energy balances are made for these two cases to check a plausible addition of power generation of turbo-generator of the steam turbine. Also, the viability issues are studied. Solvo Power Plant Simulation program is used for the energy balance research. Two case power plants are simulated to solve the balances. To solve the addition of power generation with the flue gas coolers, basic balance calculation is performed. The viabilities are also taken into account, especially the payback times of these alternatives. On the basis of the results, installing the system to the process is viable in both cases. By installing the lowest possible pressure steam system for the soot blowing, the advantages are the most significant. The investment costs are the highest but the payback time is less than 1,5 years and the profit in the next 20 years is the greatest. In the case of flue gas coolers, the results did not entirely agree with past studies. Nevertheless, installing the flue gas coolers into the process also seems to be significant and profitable.

Tuulivoimalan lapojen huolto ja tarkastukset

Uusiutuva energia elää voimakasta kasvukautta ja hallituksen tekemien tukipäätösten vuoksi tuulivoimaa tullaan rakentamaan huomattavasti lisää tulevien vuosien aikana. Tuuligeneraattorin siipien huolto- ja tarkastustoiminta on uusi ja kehittyvä toimiala. Tämä diplomityö onkin tehty oppaaksi helpottamaan tuulivoimaa omistavien, rakentavien, tai tuulivoimapuiston perustamista harkitsevien tahojen huoltosuunnitelmien tekemistä varten. Diplomityössä käydään läpi yleisimmät tuulivoimaloiden lapojen vikaantu-miset, sekä työskentelytavat ja käytettävät laitteistot voimaloiden lapojen huoltoja ja tarkastuksia tehtäessä.