静力触探锥头阻力的近似理论与实验研究进展

锥头阻力在静力触探试验中扮演着十分重要的角色．从不同角度，对触探中锥头阻力的研究进行简要阐述，对承载力理论、空洞膨胀理论、应变路径法及运动点位错法等几种理论分析方法进行了回顾．另外，对数值分析和实验研究的进展情况进行了叙述．并对各种方法的适用性进行了比较．承载力理论虽然简单，但忽略了土的压缩性和探杆周围初始应力的增加，所以不能精确地模拟锥头的深层贯入．空洞膨胀理论提供了一个分析锥头阻力的简单而较精确的方法，它考虑了土的压缩性(或膨胀性)和锥头贯入过程中锥杆周围应力增加的影响．但这种方法是将锥头贯入与空洞膨胀之间做了一个等效模拟，所以不同的模拟方法，得到的结果差别较大．应变路径法能够有效解决饱和粘土中的不排水贯入，但不适用于砂土．运动点位错法因为考虑了部分排水，所以能较好地预测固结系数，但采用了线弹性分析，故位错法在其他方面的应用还需要大量的试验验证．有限元法在处理锥头贯入这类慢侵彻问题时缺乏一种很好的处理技术，导致它在进行破坏荷载计算时有显著的误差和数值计算困难．标定槽试验将在验证和建立锥头阻力与土的性能关系方面继续起到一个重要作用，但其结果需经过校正后才可应用到现场．最后对该领域的研究趋势进行了讨论．

A constitutive description of the inelastic response of ceramics

The objective of the article is to present a unified model for the dynamic mechanical response of ceramics under compressive stress states. The model incorporates three principal deformation mechanisms: (i) lattice plasticity due to dislocation glide or twinning; (ii) microcrack extension; and (iii) granular flow of densely packed comminuted particles. In addition to analytical descriptions of each mechanism, prescriptions are provided for their implementation into a finite element code as well as schemes for mechanism transitions. The utility of the code in addressing issues pertaining to deep penetration is demonstrated through a series of calculations of dynamic cavity expansion in an infinite medium. The results reveal two limiting behavioral regimes, dictated largely by the ratio of the cavity pressure p to the material yield strength σY. At low values of p/σY, cavity expansion occurs by lattice plasticity and hence its rate diminishes with increasing σY. In contrast, at high values, expansion occurs by microcracking followed by granular plasticity and is therefore independent of σY. In the intermediate regime, the cavity expansion rate is governed by the interplay between microcracking and lattice plasticity. That is, when lattice plasticity is activated ahead of the expanding cavity, the stress triaxiality decreases (toward more negative values) which, in turn, reduces the propensity for microcracking and the rate of granular flow. The implications for penetration resistance to high-velocity projectiles are discussed. Finally, the constitutive model is used to simulate the quasi-static and dynamic indentation response of a typical engineering ceramic (alumina) and the results compared to experimental measurements. Some of the pertinent observations are shown to be captured by the present model whereas others require alternative approaches (such as those based on fracture mechanics) for complete characterization. © 2011 The American Ceramic Society.

Comportamiento prooxidante y antioxidante de hierbas aromáticas en queso

Los quesos de cabra, con mejores cualidades funcionales provienen de leche de cabras en pastoreo, esto obedece al mayor contenido de ácidos grasos ω-3 y ω-6 en una relación óptima para la salud, sumado a un menor contenido de grasa y colesterol. Saborizar quesos con especias, otorga beneficios sensoriales y saludables al producto. Las especias son usadas para realzar el flavor de los alimentos además presentan beneficios antioxidantes. Sin embargo, se reportaron evidencias del doble papel de los flavonoides como antioxidantes o prooxidantes en función de la concentración de uso. El objetivo del trabajo es evaluar el efecto de distintas concentraciones de especias aromáticas con capacidad antioxidante, frente a las reacciones de deterioro que ocurren en el almacenamiento de quesos de cabra. Se estudió la actividad antirradicalaria (AAR) de 18 especias. Para evaluar la actividad antioxidante (AA0) se usó la técnica de desaparición de un radical libre estable el 2,2-difenil-1-picril hidrazilo (DPPH) y se calculó la AAR porcentual. Definido el queso base estándar (control), se ensayaron tres variedades con especies, elegidas de entre las de mayor AAR (orégano, romero y tomillo) y se adicionaron con las concentraciones 0,4 – 1 % p/p. Estos, fueron madurados 30 días y almacenados 7 meses a 4 °C. Se analizaron cada 4 semanas. Se realizaron pruebas sensoriales de aceptabilidad con 60 consumidores de queso (condición), usando planillas, con escala hedónica. Se trabajó sobre los lípidos extraídos de los quesos. El rancidez y deterioro fueron evaluados con análisis de acidez; índice peróxido y sustancias reactivas al ácido TBA. Los resultados se compararon con el comportamiento sensorial del producto en el tiempo de almacenamiento. En los quesos adicionados al 1 %, la acidez se incrementó con el almacenamiento. El máximo valor corresponde al queso con orégano (3,72 % de ac. láctico a los 126 días). En el control, la acidez inicial fue inferior y alcanzó 1,05 g de ác. láctico % a los 166 días. El IP más alto corresponde a los quesos con orégano al 1% , resultado que se contrapone a la actividad antirradicalaria de esta especia. Al 0,4 %, tanto el IP como el número de TBA son menores en quesos adicionados, respecto del control. En los quesos de cabra analizados las especias agregadas al 1% ejercieron acción prooxidante, mientras que al ser agregadas al 0,4% la acción es antioxidante, lo que indica la importancia de la selección de concentraciones adecuadas.

Research on laser welding of cast Ni-based superalloy K418 turbo disk and alloy steel 42CrMo shaft

Exploratory experiments of laser welding cast Ni-based superalloy K418 turbo disk and alloy steel 42CrMo shaft were conducted. Microstructure of the welded seam was characterized by optical microscopy (OM), scanning electron microscopy (SEM), X-ray diffraction (XRD), energy-dispersive spectrometer (EDS). Mechanical properties of the welded seam were evaluated by microhardness and tensile strength testing. The corresponding mechanisms were discussed in detail. Results showed that the laser-welded seam had non-equilibrium solidified microstructures consisting of FeCr0.29Ni0.16C0.06 austenite solid solution dendrites as the dominant and some fine and dispersed Ni3Al gamma' phase and Laves particles as well as little amount of MC short stick or particle-like carbides distributed in the interdendritic regions. The average microhardness of the welded seam was relatively uniform and lower than that of the base metal due to partial dissolution and suppression of the strengthening phase gamma' to some extent. About 88.5% tensile strength of the base metal was achieved in the welded joint because of a non-full penetration welding and the fracture mechanism was a mixture of ductility and brittleness. The existence of some Laves particles in the welded seam also facilitated the initiation and propagation of the microcracks and microvoids and hence, the detrimental effects of the tensile strength of the welded joint. The present results stimulate further investigation on this field. (c) 2006 Elsevier B.V. All rights reserved.

Raíces ideológicas de la perspectiva de género

Resumen: El feminismo radical o de género tiene sus orígenes históricos, su matriz ideológica y su modo dialéctico de entender la relación varón-mujer, en el pensamiento marxista (Engels, de Beauvoir, Firestone). La “antítesis” de esta lucha de sexos es la revolución feminista radical, y su principal instrumento revolucionario y de penetración cultural es la ideología de género. La fase central de esta revolución es el apoderamiento, por parte de las mujeres, de los medios de reproducción. Los medios que han demostrado ser más aptos para lograr la victoria son el aborto por decisión privativa de la mujer, la fecundación artificial y el matrimonio entre personas del mismo sexo. La revolución se libra en el campo cultural y, luego, en el jurídico.

Scaling Functions In Conical Indentation Of Elastic-Plastic Solids

The finite element method was used to simulate the conical indentation of elastic-plastic solids with work hardening. The ratio of the initial yield strength to the Young's modulus Y/E ranged from 0 to 0.02. Based on the calculation results, two sets of scaling functions for non-dimensional hardness H/K and indenter penetration h are presented in the paper, which have closed simple mathematical form and can be used easily for engineering application. Using the present scaling functions, indentation hardness and indentation loading curves can be easily obtained for a given set of material properties. Meanwhile one can use these scaling functions to obtain material parameters by an instrumented indentation load-displacement curve for loading and unloading if Young's modulus E and Poisson's ratio nu are known.

Un testigo directo de las tensiones religiosas en la Alejandría de los siglos IV y V D.C. : Páladas de Alejandría en la Antología Palatina

Abstract: Although he is the most prolific writer of the Greek Anthology, Palladas’ life is almost unknown. But, in spite of the limited biographical data, his work has fortunately been preserved in the GA. Because of his literary creation, the old times rewarded him with the nickname Μετέωρος, high, since the literary merits of a hundred poems of his authorship was recognized (others are discussed by critics). A dozen of them contains invaluable information about the political, religious and social situation in Alexandria immediately after the victory of the bishop Theophilus, Cyril’s predecessor and uncle, during the conflict between Christians and Gentiles, each sector backed up by an Alexandrian population segment (cfr. 9.528, 10.82, 10.85) . Resigned at times, constantly demanding, Palladas complains about the decline of the belief professed by him due to the increasing penetration of the new faith. Therefore, four epigrams record the conversion of the temple of Tyche into a tavern (9.180-183) and 10.90 seems to attack the doctrine of the Resurrection. When religion and politics go hand-in-hand, when religious conspiracies link up with palace intrigues, consequences are predictable: a man called Doroteo denounced him for his negative response to the new dogma, which caused him the loss of his teacher paid work. His annoyance was even greater with further sufferings, chiefly economic, and he had to sell his books (9.171 and 9.175) among other desperate decisions Forewarned about his radical bitterness against Church, it is just to make clear that he is not fully acquiescent with ancient gods and heroes. Thus, in 5.257 he questions Zeus’ ars amandi, in 9.377 refutes Tantalus’ possibility of thirst and hunger in Hades and 9.773 mischievously points out that Eros has been changed into a pan. The work begins with the selection, personal translation and comprehensive analysis of twenty two epigrams. Through such philological aid, we attempt to verify the frictions and the main perceptible factors in his poetic creation to justify his worldview, according to the pagan sentiment widespread in that time before the twilight already overwhelming of its ailing traditions

MD simulation of the effect of contact area and tip radius on nanoindentation

Molecular dynamics simulations of nanoindentation are performed on monocrystal copper. A new "contact atoms" method is presented for calculating the contact area. Compared with conventional methods, this method can provide the contact area more accurately not only for sink-in but also for pile-up situation. The effect of tip radius on indentation is investigated too. The results indicate that the measured hardness of the material will become higher as the tip radius increases.

Crack deflection at an interface between dissimilar elastic-materials

A crack intersecting an interface between two dissimilar materials may advance by either penetrating through the interface or deflecting into the interface. The competition between deflection and penetration can be assessed by comparison of two ratios: (i) the ratio of the energy release rates for interface cracking and crack penetration; and (ii) the ratio of interface to material fracture energies. Residual stresses caused by thermal expansion misfit can influence the energy release rates of both the deflected and penetrating crack. This paper analyses the role of residual stresses. The results reveal that expansion misfit can be profoundly important in systems with planar interfaces (such as layered materials, thin film structures, etc.), but generally can be expected to be of little significance in fiber composites. This paper corrects an earlier result for the ratio of the energy release rate for the doubly deflected crack to that for the penetrating crack in the absence of residual stress.

K418与42CrMo异种金属激光深熔焊接

研究了连续波Nd:YAG激光焊接功率、速度、离焦量和侧吹保护气流量对激光深熔焊接K418与42CrMo异种金属焊缝形貌、焊缝熔深的影响,讨论了焊缝区热裂纹产生机制.结果表明,额定功率为3 kW的Nd:YAG激光深熔焊接K418与42CrMo异种金属,由于它们的物理化学性质的差异,焊缝靠近42CrMo侧易出现未熔合;激光光斑向42CrMo侧偏移可以减少焊缝靠近42CrMo侧未熔合量;通过优化侧吹保护气流量和离焦量可以增加熔深.由于K418液态金属的流动性差,导致焊缝靠近K418侧对流传热不充分,使焊缝靠近K418侧熔合线呈现锯齿形.焊缝区热裂纹的产生主要是由于焊缝区元素偏析形成的低熔物导致.

Evaluation of bioactive sphingolipids in 4-HPR-resistant leukemia cells

Background -- N-(4-hydroxyphenyl)retinamide (4-HPR, fenretinide) is a synthetic retinoid with potent pro-apoptotic activity against several types of cancer, but little is known regarding mechanisms leading to chemoresistance. Ceramide and, more recently, other sphingolipid species (e.g., dihydroceramide and dihydrosphingosine) have been implicated in 4-HPR-mediated tumor cell death. Because sphingolipid metabolism has been reported to be altered in drug-resistant tumor cells, we studied the implication of sphingolipids in acquired resistance to 4-HPR based on an acute lymphoblastic leukemia model. Methods -- CCRF-CEM cell lines resistant to 4-HPR were obtained by gradual selection. Endogenous sphingolipid profiles and in situ enzymatic activities were determined by LC/MS, and resistance to 4-HPR or to alternative treatments was measured using the XTT viability assay and annexin V-FITC/propidium iodide labeling. Results -- No major crossresistance was observed against other antitumoral compounds (i.e. paclitaxel, cisplatin, doxorubicin hydrochloride) or agents (i.e. ultra violet C, hydrogen peroxide) also described as sphingolipid modulators. CCRF-CEM cell lines resistant to 4-HPR exhibited a distinctive endogenous sphingolipid profile that correlated with inhibition of dihydroceramide desaturase. Cells maintained acquired resistance to 4-HPR after the removal of 4-HPR though the sphingolipid profile returned to control levels. On the other hand, combined treatment with sphingosine kinase inhibitors (unnatural (dihydro)sphingosines ((dh)Sph)) and glucosylceramide synthase inhibitor (PPMP) in the presence or absence of 4-HPR increased cellular (dh)Sph (but not ceramide) levels and were highly toxic for both parental and resistant cells. Conclusions -- In the leukemia model, acquired resistance to 4-HPR is selective and persists in the absence of sphingolipid profile alteration. Therapeutically, the data demonstrate that alternative sphingolipid-modulating antitumoral strategies are suitable for both 4-HPR-resistant and sensitive leukemia cells. Thus, whereas sphingolipids may not be critical for maintaining resistance to 4-HPR, manipulation of cytotoxic sphingolipids should be considered a viable approach for overcoming resistance.

砂土地基中吸力式沉箱的极限沉贯深度分析

吸力式沉箱是广泛应用于离岸结构物中的新型基础形式,贯入分析方法的研究是很重要的课题.分析了砂性土地基吸力贯入过程中的渗流状况,得出了筒内壁的压降比率与贯入深径比的关系公式,分析评估了抽吸作用对筒内壁压降比率的影响,提出了砂土地基中吸力贯入阻力和地基极限吸力的简便计算方法,给出了砂土地基中极限贯入深径比的计算公式,分析了各种砂土地基中的吸力贯入极限深径比.不计简体自重和抽吸效应影响时,这一比值介于2.1～2.5之间.

Proceso del desarrollo exportador de la PYME colombiana

[ES] Las Pymes colombianas, al igual que las de América Latina, afrontan una serie de barreras para la exportación asociadas a la carencia de recursos y capacidades organizacionales y directivas, las cuales hacen que su permanencia en los mercados internacionales sea cuestionable. Al no superar tales barreras y mostrar una posición competitiva más fuerte difícilmente éstas podrán penetrar y sobrevivir en los mercados internacionales y aprovechar las grandes oportunidades que ofrece el mercado mundial. Especialmente, aquéllas que surgen como resultado de los acuerdos de integración y de los sistemas de preferencia suscritos y otorgados a Colombia.

亚声速段横向射流对Coil性能影响的数值研究

在化学氧碘激光的混合喷管内发生的是一个气体动力学、化学反应动力学以及光学等相互耦合的复杂过程,每个过程都对COIL性能有着至关重要的影响.利用三维CFD技术,通过求解层流Navier-Stokes方程与组分输运方程,对简化后的化学氧碘激光RADICL模型进行数值模拟与分析,对COIL的气动和增益特性进行探讨.在不同的射流穿透条件下,计算COIL混合喷管中的混合与化学反应过程,发现穿透深度决定了增益的分布特性以及过度穿透条件下的非定常结构,

Evolución y tendencias de la marca de distribuidor en los mercados de gran consumo: el caso de España

[ES] La marca de distribuidor está experimentando un proceso de crecimiento notable en nuestro país, especialmente en los mercados de productos de gran consumo. Sobre este particular, este trabajo tiene por objeto analizar la situación actual así como las tendencias futuras en la comercialización de marcas de distribuidor en la industria de productos de gran consumo. Para ello, se tendrá en cuenta la penetración de las marcas de distribuidor en distintas categorías de productos de gran consumo, exponiéndose una serie de argumentos con objeto de explicar las tendencias observadas.