Indicadores bibliométricos em sistemas de informação: uma análise a partir de artigos publicados no Encontro Nacional de Engenharia de Produção

This research aims at to contribute to show the consolidation of the area of Information Systems (IS) as area of knowledge in Production Engineering. For this, it according to presents a scenery of the publication in IS in the field of the Production Engineering in Brazil amount of articles, the authorship profile, the methodologies, the citations, the research thematic and the continuity of the research thematic. The base for this study was the works published in the National Meeting of Production Engineering - ENEGEP of years 2000, 2001, 2002, 2003 and 2004, inside of the area of Information Systems. Classified as bibliographical research, of applied nature, quantitative boarding, of the point of view of the objectives description-exploration was called and for the collection of data its comment was systematic with bibliographical survey. As field research, the method of collection of data if constituted of the elaboration of an analysis protocol and, to arrive itself at the final diagnosis, it operation the data through the statistical method, with the accomplishment of descriptive analyses. It approached concepts of IS and the seek areas and, it studied research correlate in Production Engineering, in Information Systems, in Information Science and other areas of the knowledge. How much to the results one concluded that the national and international contents are compatible and that the area of IS is in constant evolution. For the continuity of research lines it was observed that the majority of the authors was faithful to the area of Systems of Information. Amongst other found results, some institutions must try to increase its volume of publications and research, while others must look for to keep its reached mark already in the last years

Uma aplicação de análise de decisão com o método AHP Processo de hierarquia analítica: um estudo sobre adoção de Sistema eletrônico de cobrança no Transporte público urbano

This thesis carries through an application of Analysis of Multicriterion Decision with use of the method of Analytical Hierarchy Process (AHP) in the problematic one of taking of decision of the adoption of electronic collecting in the system of urban transport in the country, a subject that has been controversial. A modeling of criteria and alternatives is carried through and applied a questionnaire based on method AHP the excellent actors in the system of urban transport - Leading of the Managing Agency Public Municipal theatre of Urban Transports, Controller of Company of Bus, Controller of Labor union, Controller of Union of Companies, Communitarian Leader. The considered alternatives were: the maintenance of the current state with collectors, the implementation of electronic collection without collectors, and the implementation of electronic collection with collectors. The used criteria were: job, impact in the fare, control of the system, easiness of use, information. The study was carried through in the city of Natal, RN, where if the adoption of electronic collection argues and where this implementation in some bus lines between Natal and Parnamirim exists, city that integrates the region of the great Natal. The main results of the method evidence in a dimension, the viability of use of method AHP with questionnaire by means of validation of the judgments with analysis of variance beyond proper the normal mechanisms of analysis of consistency to the method, and in another one, the contribution of the analysis boarding multicriterion to become the judgments more clearly. The main results of the analysis help to show that although to models of criteria and distinct judgments of the actors, the method evidenced that it has inclination the adoption of the electronic collection on the current situation, even so with divergences between the maintenance or not of the collector. The research points to the possibility of accomplishment of the application of the AHP in successive rounds of judgments

Uso de técnicas de otimização baseadas em derivadas como suporte do planejamento operacional de redes de distribuição de energia elétrica

The usual programs for load flow calculation were in general developped aiming the simulation of electric energy transmission, subtransmission and distribution systems. However, the mathematical methods and algorithms used by the formulations were based, in majority, just on the characteristics of the transmittion systems, which were the main concern focus of engineers and researchers. Though, the physical characteristics of these systems are quite different from the distribution ones. In the transmission systems, the voltage levels are high and the lines are generally very long. These aspects contribute the capacitive and inductive effects that appear in the system to have a considerable influence in the values of the interest quantities, reason why they should be taken into consideration. Still in the transmission systems, the loads have a macro nature, as for example, cities, neiborhoods, or big industries. These loads are, generally, practically balanced, what reduces the necessity of utilization of three-phase methodology for the load flow calculation. Distribution systems, on the other hand, present different characteristics: the voltage levels are small in comparison to the transmission ones. This almost annul the capacitive effects of the lines. The loads are, in this case, transformers, in whose secondaries are connected small consumers, in a sort of times, mono-phase ones, so that the probability of finding an unbalanced circuit is high. This way, the utilization of three-phase methodologies assumes an important dimension. Besides, equipments like voltage regulators, that use simultaneously the concepts of phase and line voltage in their functioning, need a three-phase methodology, in order to allow the simulation of their real behavior. For the exposed reasons, initially was developped, in the scope of this work, a method for three-phase load flow calculation in order to simulate the steady-state behaviour of distribution systems. Aiming to achieve this goal, the Power Summation Algorithm was used, as a base for developing the three phase method. This algorithm was already widely tested and approved by researchers and engineers in the simulation of radial electric energy distribution systems, mainly for single-phase representation. By our formulation, lines are modeled in three-phase circuits, considering the magnetic coupling between the phases; but the earth effect is considered through the Carson reduction. It s important to point out that, in spite of the loads being normally connected to the transformer s secondaries, was considered the hypothesis of existence of star or delta loads connected to the primary circuit. To perform the simulation of voltage regulators, a new model was utilized, allowing the simulation of various types of configurations, according to their real functioning. Finally, was considered the possibility of representation of switches with current measuring in various points of the feeder. The loads are adjusted during the iteractive process, in order to match the current in each switch, converging to the measured value specified by the input data. In a second stage of the work, sensibility parameters were derived taking as base the described load flow, with the objective of suporting further optimization processes. This parameters are found by calculating of the partial derivatives of a variable in respect to another, in general, voltages, losses and reactive powers. After describing the calculation of the sensibility parameters, the Gradient Method was presented, using these parameters to optimize an objective function, that will be defined for each type of study. The first one refers to the reduction of technical losses in a medium voltage feeder, through the installation of capacitor banks; the second one refers to the problem of correction of voltage profile, through the instalation of capacitor banks or voltage regulators. In case of the losses reduction will be considered, as objective function, the sum of the losses in all the parts of the system. To the correction of the voltage profile, the objective function will be the sum of the square voltage deviations in each node, in respect to the rated voltage. In the end of the work, results of application of the described methods in some feeders are presented, aiming to give insight about their performance and acuity

Localização e mapeamento simultâneos de ambientes planos usando visão monocular e representação híbrida do ambiente

The goal of this work is to propose a SLAM (Simultaneous Localization and Mapping) solution based on Extended Kalman Filter (EKF) in order to make possible a robot navigates along the environment using information from odometry and pre-existing lines on the floor. Initially, a segmentation step is necessary to classify parts of the image in floor or non floor . Then the image processing identifies floor lines and the parameters of these lines are mapped to world using a homography matrix. Finally, the identified lines are used in SLAM as landmarks in order to build a feature map. In parallel, using the corrected robot pose, the uncertainty about the pose and also the part non floor of the image, it is possible to build an occupancy grid map and generate a metric map with the obstacle s description. A greater autonomy for the robot is attained by using the two types of obtained map (the metric map and the features map). Thus, it is possible to run path planning tasks in parallel with localization and mapping. Practical results are presented to validate the proposal

Dedução de Funções de Alívio para Priorização de Variantes de Chaveamento Adequadas à Eliminação de Sobrecargas

Eventually, violations of voltage limits at buses or admissible loadings of transmission lines and/or power transformers may occur by the power system operation. If violations are detected in the supervision process, corrective measures may be carried out in order to eliminate them or to reduce their intensity. Loading restriction is an extreme solution and should only be adopted as the last control action. Previous researches have shown that it is possible to control constraints in electrical systems by changing the network topology, using the technique named Corrective Switching, which requires no additional costs. In previous works, the proposed calculations for verifying the ability of a switching variant in eliminating an overload in a specific branch were based on network reduction or heuristic analysis. The purpose of this work is to develop analytical derivation of linear equations to estimate current changes in a specific branch (due to switching measures) by means of few calculations. For bus-bar coupling, derivations will be based on short-circuit theory and Relief Function methodology. For bus-bar splitting, a Relief Function will be derived based on a technique of equivalent circuit. Although systems of linear equations are used to substantiate deductions, its formal solution for each variant, in real time does not become necessary. A priority list of promising variants is then assigned for final check by an exact load flow calculation and a transient analysis using ATP Alternative Transient Program. At last, results obtained by simulation in networks with different features will be presented

Análise dos Modos Ressonantes em Antenas de Microfita sobre Substratos Iso/Anisotrópicos por Técnicas da Ressonância Transversa

Neste trabalho, são utilizadas a Técnica da Ressonância Transversa (TRT) e a Técnica da Ressonância Transversa Modificada (MTRT), para a determinação das freqüências dos modos ressonantes de antenas de microfita com patch quadrado, retangular e circular e com substratos isotrópicos e anisotrópicos. Para isso, é proposto um modelo da cavidade equivalente, onde a antena tipo patch retangular é representada como sendo a superposição de duas linhas infinitas em microfita, uma de largura W, representando a dimensão que expressa a largura do patch, e a outra com largura L, representando a dimensão que expressa o comprimento do patch. A avaliação da eficiência e aplicabilidade dos métodos citados é realizada comparando-se com resultados experimentais e obtidos através de outras técnicas. Três situações serão verificadas: estruturas com substrato infinito, estrutura com substrato tipo pedestal e estruturas com substrato truncado além dos limites da fita metálica. Os resultados obtidos demonstram que as técnicas de análise de onda completa utilizadas neste trabalho, por um formalismo matemático mais rigoroso, são eficientes e precisas tanto na aplicação em estruturas com substrato isotrópico como nas que possuem substrato anisotrópico. Inicialmente são consideradas apenas as estruturas com substratos isotrópicos, com diferentes constantes dielétricas, e é avaliada a influência da largura do substrato sobre as freqüências dos modos ressonantes das antenas. Posteriormente, a análise do truncamento do dielétrico é realizada para estruturas com substrato anisotrópico. Em todos os casos, os resultados experimentais, obtidos a partir da construção de protótipos, são confrontados com os obtidos a partir de simulação, utilizando as técnicas TRT e MTRT. No final, as técnicas descritas são utilizadas para antenas tipo patch circular, sendo utilizada uma técnica de equivalência para transformar a antena circular em outra quadrada ou retangular equivalente, dependendo do modo que se queira encontrar. Os resultados obtidos são então analisados, observando-se uma boa concordância e indicando a viabilidade do método. Após isso, são apresentadas as conclusões e sugeridos alguns temas para a continuidade deste trabalho

Uso de técnicas de otimização baseadas em derivadas como suporte do planejamento operacional de redes de distribuição de energia elétrica

The usual programs for load flow calculation were in general developped aiming the simulation of electric energy transmission, subtransmission and distribution systems. However, the mathematical methods and algorithms used by the formulations were based, in majority, just on the characteristics of the transmittion systems, which were the main concern focus of engineers and researchers. Though, the physical characteristics of these systems are quite different from the distribution ones. In the transmission systems, the voltage levels are high and the lines are generally very long. These aspects contribute the capacitive and inductive effects that appear in the system to have a considerable influence in the values of the interest quantities, reason why they should be taken into consideration. Still in the transmission systems, the loads have a macro nature, as for example, cities, neiborhoods, or big industries. These loads are, generally, practically balanced, what reduces the necessity of utilization of three-phase methodology for the load flow calculation. Distribution systems, on the other hand, present different characteristics: the voltage levels are small in comparison to the transmission ones. This almost annul the capacitive effects of the lines. The loads are, in this case, transformers, in whose secondaries are connected small consumers, in a sort of times, mono-phase ones, so that the probability of finding an unbalanced circuit is high. This way, the utilization of three-phase methodologies assumes an important dimension. Besides, equipments like voltage regulators, that use simultaneously the concepts of phase and line voltage in their functioning, need a three-phase methodology, in order to allow the simulation of their real behavior. For the exposed reasons, initially was developped, in the scope of this work, a method for three-phase load flow calculation in order to simulate the steady-state behaviour of distribution systems. Aiming to achieve this goal, the Power Summation Algorithm was used, as a base for developping the three phase method. This algorithm was already widely tested and approved by researchers and engineers in the simulation of radial electric energy distribution systems, mainly for single-phase representation. By our formulation, lines are modeled in three-phase circuits, considering the magnetic coupling between the phases; but the earth effect is considered through the Carson reduction. Its important to point out that, in spite of the loads being normally connected to the transformers secondaries, was considered the hypothesis of existence of star or delta loads connected to the primary circuit. To perform the simulation of voltage regulators, a new model was utilized, allowing the simulation of various types of configurations, according to their real functioning. Finally, was considered the possibility of representation of switches with current measuring in various points of the feeder. The loads are adjusted during the iteractive process, in order to match the current in each switch, converging to the measured value specified by the input data. In a second stage of the work, sensibility parameters were derived taking as base the described load flow, with the objective of suporting further optimization processes. This parameters are found by calculating of the partial derivatives of a variable in respect to another, in general, voltages, losses and reactive powers. After describing the calculation of the sensibility parameters, the Gradient Method was presented, using these parameters to optimize an objective function, that will be defined for each type of study. The first one refers to the reduction of technical losses in a medium voltage feeder, through the installation of capacitor banks; the second one refers to the problem of correction of voltage profile, through the instalation of capacitor banks or voltage regulators. In case of the losses reduction will be considered, as objective function, the sum of the losses in all the parts of the system. To the correction of the voltage profile, the objective function will be the sum of the square voltage deviations in each node, in respect to the rated voltage. In the end of the work, results of application of the described methods in some feeders are presented, aiming to give insight about their performance and acuity

Dinâmica da Plasticidade Sináptica em neurônios do hipocampo durante ciclos de sono: um estudo computacional

Several research lines show that sleep favors memory consolidation and learning. It has been proposed that the cognitive role of sleep is derived from a global scaling of synaptic weights, able to homeostatically restore the ability to learn new things, erasing memories overnight. This phenomenon is typical of slow-wave sleep (SWS) and characterized by non-Hebbian mechanisms, i.e., mechanisms independent of synchronous neuronal activity. Another view holds that sleep also triggers the specific enhancement of synaptic connections, carrying out the embossing of certain mnemonic traces within a lattice of synaptic weights rescaled each night. Such an embossing is understood as the combination of Hebbian and non-Hebbian mechanisms, capable of increasing and decreasing respectively the synaptic weights in complementary circuits, leading to selective memory improvement and a restructuring of synaptic configuration (SC) that can be crucial for the generation of new behaviors ( insights ). The empirical findings indicate that initiation of Hebbian plasticity during sleep occurs in the transition of the SWS to the stage of rapid eye movement (REM), possibly due to the significant differences between the firing rates regimes of the stages and the up-regulation of factors involved in longterm synaptic plasticity. In this study the theories of homeostasis and embossing were compared using an artificial neural network (ANN) fed with action potentials recorded in the hippocampus of rats during the sleep-wake cycle. In the simulation in which the ANN did not apply the long-term plasticity mechanisms during sleep (SWS-transition REM), the synaptic weights distribution was re-scaled inexorably, for its mean value proportional to the input firing rate, erasing the synaptic weights pattern that had been established initially. In contrast, when the long-term plasticity is modeled during the transition SWSREM, an increase of synaptic weights were observed in the range of initial/low values, redistributing effectively the weights in a way to reinforce a subset of synapses over time. The results suggest that a positive regulation coming from the long-term plasticity can completely change the role of sleep: its absence leads to forgetting; its presence leads to a positive mnemonic change

Antenas de microfita com patch quase-fractal para aplicações em Redes WPAN/WLAN

The microstrip antennas are in constant evidence in current researches due to several advantages that it presents. Fractal geometry coupled with good performance and convenience of the planar structures are an excellent combination for design and analysis of structures with ever smaller features and multi-resonant and broadband. This geometry has been applied in such patch microstrip antennas to reduce its size and highlight its multi-band behavior. Compared with the conventional microstrip antennas, the quasifractal patch antennas have lower frequencies of resonance, enabling the manufacture of more compact antennas. The aim of this work is the design of quasi-fractal patch antennas through the use of Koch and Minkowski fractal curves applied to radiating and nonradiating antenna s edges of conventional rectangular patch fed by microstrip inset-fed line, initially designed for the frequency of 2.45 GHz. The inset-fed technique is investigated for the impedance matching of fractal antennas, which are fed through lines of microstrip. The efficiency of this technique is investigated experimentally and compared with simulations carried out by commercial software Ansoft Designer used for precise analysis of the electromagnetic behavior of antennas by the method of moments and the neural model proposed. In this dissertation a study of literature on theory of microstrip antennas is done, the same study is performed on the fractal geometry, giving more emphasis to its various forms, techniques for generation of fractals and its applicability. This work also presents a study on artificial neural networks, showing the types/architecture of networks used and their characteristics as well as the training algorithms that were used for their implementation. The equations of settings of the parameters for networks used in this study were derived from the gradient method. It will also be carried out research with emphasis on miniaturization of the proposed new structures, showing how an antenna designed with contours fractals is capable of a miniaturized antenna conventional rectangular patch. The study also consists of a modeling through artificial neural networks of the various parameters of the electromagnetic near-fractal antennas. The presented results demonstrate the excellent capacity of modeling techniques for neural microstrip antennas and all algorithms used in this work in achieving the proposed models were implemented in commercial software simulation of Matlab 7. In order to validate the results, several prototypes of antennas were built, measured on a vector network analyzer and simulated in software for comparison

Um estudo de estruturas com PBG e fotônica

One of the objectives of this work is the ana1ysis of planar structures using the PBG (photonic Bandgap), a new method of controlling propagation of electromagnetic waves in devices with dielectrics. Here the basic theory of these structures will be presented, as well as applications and determination of certain parameters. In this work the analysis will be performed concerning PBG structures, including the basic theory and applications in planar structures. Considerations are made related to the implementation of devices. Here the TTL (Transverse Transmission Line) method is employed, characterized by the simplicity in the treatment of the equations that govern the propagation of electromagnetic waves in the structure. In this method, the fields in x and z are expressed in function of the fields in the traverse direction y in FTD (Fourier Transform Domain). This method is useful in the determination of the complex propagation constant with application in high frequency and photonics. In this work structures will be approached in micrometric scale operating in frequencies in the range of T erahertz, a first step for operation in the visible spectra. The mathematical basis are approached for the determination of the electromagnetic fields in the structure, based on the method L TT taking into account the dimensions approached in this work. Calculations for the determination of the constant of complex propagation are also carried out. The computational implementation is presented for high frequencies. at the first time the analysis is done with base in open microstrip lines with semiconductor substrate. Finally, considerations are made regarding applications ofthese devices in the area of telecommunications, and suggestions for future

Técnica de controle adaptativo robusto aplicada a filtros ativos de potência e paralelo

The Methods for compensation of harmonic currents and voltages have been widely used since these methods allow to reduce to acceptable levels the harmonic distortion in the voltages or currents in a power system, and also compensate reactive. The reduction of harmonics and reactive contributes to the reduction of losses in transmission lines and electrical machinery, increasing the power factor, reduce the occurrence of overvoltage and overcurrent. The active power filter is the most efficient method for compensation of harmonic currents and voltages. The active power filter is necessary to use current and voltage controllers loop. Conventionally, the current and voltage control loop of active filter has been done by proportional controllers integrative. This work, investigated the use of a robust adaptive control technique on the shunt active power filter current and voltage control loop to increase robustness and improve the performance of active filter to compensate for harmonics. The proposed control scheme is based on a combination of techniques for adaptive control pole placement and variable structure. The advantages of the proposed method over conventional ones are: lower total harmonic distortion, more flexibility, adaptability and robustness to the system. Moreover, the proposed control scheme improves the performance and improves the transient of active filter. The validation of the proposed technique was verified initially by a simulation program implemented in C++ language and then experimental results were obtained using a prototype three-phase active filter of 1 kVA

EFEITOS DE DIFERENTES ESPAÇAMENTOS ENTRE SULCOS NA PRODUTIVIDADE AGRÍCOLA da CANA-DE-AÇÚCAR (Saccharum spp.)

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Acoplador e linha de lâmina unilateral e bilateral com substrato fotônico

The aim of this work is to characterize and use the characteristic parameters of the planar structures constructed with fin lines looking for their applications in devices, using PBG Photonic Band Gap photonic materials as substrate, operating in the millimeter and optic wave bands.The PBG theory will be applied for the relative permittivity attainment for the PBG photonic substrate s and p polarizations. The parameters considered in the structures characterization are the complex propagation constant and the characteristic impedance of unilateral and bilateral fin lines that were obtained by the use of the TTL Transverse Transmission Line Method, together with the Method of the Moments. The final part of this work comprises studies related to the behavior of the asymmetric unilateral fin line coupler with photonic substrate. This research opens perspectives for new works in this modern area. Numerical results are shown by means of bi-dimensional and three-dimensional graphics. Conclusions and suggestions for future works are also presented

Desempenho operacional de uma semeadora-adubadora de precisão, em função do preparo do solo e do manejo da cobertura de inverno

Avaliou-se o desempenho operacional de campo de uma semeadora-adubadora de precisão, equipada com seis linhas espaçadas de 550 mm, em um solo muito argiloso, classificado como Nitossolo Vermelho Distrófico Latossólico, na semeadura do feijoeiro (Phaseolus vulgaris L.). Os tratamentos consistiram de três métodos de preparo do solo: a) convencional (uma aração com arado de discos e duas gradagens niveladoras); b) escarificação (uma passagem de escarificador conjugado com rolo destorroador), e c) semeadura direta. Esses procedimentos foram combinados com quatro condições de cobertura do solo no inverno (consórcio aveia-preta + nabo forrageiro manejados com rolo-faca, triturador de palhas, herbicida e solo em pousio). Os métodos de preparo do solo e os manejos da cobertura foram repetidos por três anos consecutivos. Os valores de força e pico de força de tração na barra, patinagem dos rodados motrizes e consumo de combustível foram maiores no preparo com escarificador em relação aos obtidos no preparo convencional e na semeadura direta. A capacidade de campo efetiva foi maior na semeadura direta em relação aos outros tratamentos. Os manejos efetuados nas coberturas vegetais e o solo mantido em pousio não influenciaram em nenhuma das variáveis.

Análise de onda completa de superfície seletiva em freqüência do tipo anteparo duplo

This work presents a theoretical analysis and numerical and experimental results of the scattering characteristics of frequency selective surfaces, using elements of type patch perfectly conductor. The structures are composed of two frequency selective surfaces on isotropic dielectric substrates cascaded, separated by a layer of air. The analysis is performed using the method of equivalent transmission line in combination with the Galerkin method, to determine the transmission and reflection characteristics of the structures analyzed. Specifically, the analysis uses the impedance method, which models the structure by an equivalent circuit, and applies the theory of transmission lines to determine the dyadic Green's function for the cascade structure. This function relates the incident field and surface current densities. These fields are determined algebraically by means of potential incidents and the imposition of the continuity of the fields in the dielectric interfaces. The Galerkin method is applied to the numerical determination of the unknown weight coefficients and hence the unknown densities of surface currents, which are expanded in terms of known basis functions multiplied by these weight coefficients. From the determination of these functions, it becomes possible to obtain numerical scattered fields at the top and bottom of the structures and characteristics of transmission and reflection of these structures. At work, we present numerical and experimental results for the characteristics of transmission and reflection. Comparisons were made with other results presented in literature, and it was observed a good agreement in the cases presented suggestions continuity of the work are presented