Wet Oxidation of Concentrated Wastewaters: Process Combination and Reaction Kinetic Modeling

The accumulation of aqueous pollutants is becoming a global problem. The search for suitable methods and/or combinations of water treatment processes is a task that can slow down and stop the process of water pollution. In this work, the method of wet oxidation was considered as an appropriate technique for the elimination of the impurities present in paper mill process waters. It has been shown that, when combined with traditional wastewater treatment processes, wet oxidation offers many advantages. The combination of coagulation and wet oxidation offers a new opportunity for the improvement of the quality of wastewater designated for discharge or recycling. First of all, the utilization of coagulated sludge via wet oxidation provides a conditioning process for the sludge, i.e. dewatering, which is rather difficult to carry out with untreated waste. Secondly, Fe2(SO4)3, which is employed earlier as a coagulant, transforms the conventional wet oxidation process into a catalytic one. The use of coagulation as the post-treatment for wet oxidation can offer the possibility of the brown hue that usually accompanies the partial oxidation to be reduced. As a result, the supernatant is less colored and also contains a rather low amount of Fe ions to beconsidered for recycling inside mills. The thickened part that consists of metal ions is then recycled back to the wet oxidation system. It was also observed that wet oxidation is favorable for the degradation of pitch substances (LWEs) and lignin that are present in the process waters of paper mills. Rather low operating temperatures are needed for wet oxidation in order to destruct LWEs. The oxidation in the alkaline media provides not only the faster elimination of pitch and lignin but also significantly improves the biodegradable characteristics of wastewater that contains lignin and pitch substances. During the course of the kinetic studies, a model, which can predict the enhancements of the biodegradability of wastewater, was elaborated. The model includes lumped concentrations suchas the chemical oxygen demand and biochemical oxygen demand and reflects a generalized reaction network of oxidative transformations. Later developments incorporated a new lump, the immediately available biochemical oxygen demand, which increased the fidelity of the predictions made by the model. Since changes in biodegradability occur simultaneously with the destruction of LWEs, an attempt was made to combine these two facts for modeling purposes.

Supporting knowledge creation and sharing in the early phases of the strategic innovation process

The driving forces of technology and globalization continuously transform the business landscape in a way which undermines the existing strategies and innovations of organizations. The challenge for organizations is to establish such conditions where they are able to create new knowledge for innovative business ideas in interaction between other organizations and individuals. Innovation processes continuously need new external stimulations and seek new ideas, new information and knowledge locating more and more outside traditional organizational boundaries. In several studies, the early phases of the innovation process have been considered as the most critical ones. During these phases, the innovation process can emerge or conclude. External knowledge acquirement and utilization are noticed to be important at this stage of the innovation process giving information about the development of future markets and needs for new innovative businessideas. To make it possible, new methods and approaches to manage proactive knowledge creation and sharing activities are needed. In this study, knowledge creation and sharing in the early phases of the innovation process has been studied, and the understanding of knowledge management in the innovation process in an open and collaborative context advanced. Furthermore, the innovation management methods in this study are combined in a novel way to establish an open innovation process and tested in real-life cases. For these purposes two complementary and sequentially applied group work methods - the heuristic scenario method and the idea generation process - are examined by focusing the research on the support of the open knowledge creation and sharing process. The research objective of this thesis concerns two doctrines: the innovation management including the knowledge management, and the futures research concerning the scenario paradigm. This thesis also applies the group decision support system (GDSS) in the idea generation process to utilize the converged knowledge during the scenario process.

Mobile Communications within the European Union: The Role of Location in the Evolution and Forecasting of the Diffusion Process

In the European Union, the importance of mobile communications was realized early on. The process of mobile communications becoming ubiquitous has taken time, as the innovation of mobile communications diffused into the society. The aim of this study is to find out how the evolution and spatial patterns of the diffusion of mobile communications within the European Union could be taken into account in forecasting the diffusion process. There is relatively lot of research of innovation diffusion on the individual (micro) andthe country (macro) level, if compared to the territorial level. Territorial orspatial diffusion refers either to the intra-country or inter-country diffusionof an innovation. In both settings, the dif- fusion of a technological innovation has gained scarce attention. This study adds knowledge of the diffusion between countries, focusing especially on the role of location in this process. The main findings of the study are the following: The penetration rates of the European Union member countries have become more even in the period of observation, from the year 1981 to 2000. The common digital GSM system seems to have hastened this process. As to the role of location in the diffusion process, neighboring countries have had similar diffusion processes. They can be grouped into three, the Nordic countries, the central and southern European countries, and the remote southern European countries. The neighborhood effect is also domi- nating in thegravity model which is used for modeling the adoption timing of the countries. The subsequent diffusion within a country, measured by the logistic model in Finland, is af- fected positively by its economic situation, and it seems to level off at some 92 %. Considering the launch of future mobile communications systemsusing a common standard should implicate an equal development between the countries. The launching time should be carefully selected as the diffusion is probably delayed in economic downturns. The location of a country, measured by distance, can be used in forecasting the adoption and diffusion. Fi- nally, the result of penetration rates becoming more even implies that in a relatively homoge- nous set of countries, such as the European Union member countries, the estimated final pene- tration of a single country can be used for approximating the penetration of the others. The estimated eventual penetration of Finland, some 92 %, should thus also be the eventual level for all the European Union countries and for the European Union as a whole.

Welding time models for cost calculations in the early stages of the design process

It is generally accepted that between 70 and 80% of manufacturing costs can be attributed to design. Nevertheless, it is difficult for the designer to estimate manufacturing costs accurately, especially when alternative constructions are compared at the conceptual design phase, because of the lack of cost information and appropriate tools. In general, previous reports concerning optimisation of a welded structure have used the mass of the product as the basis for the cost comparison. However, it can easily be shown using a simple example that the use of product mass as the sole manufacturing cost estimator is unsatisfactory. This study describes a method of formulating welding time models for cost calculation, and presents the results of the models for particular sections, based on typical costs in Finland. This was achieved by collecting information concerning welded products from different companies. The data included 71 different welded assemblies taken from the mechanical engineering and construction industries. The welded assemblies contained in total 1 589 welded parts, 4 257 separate welds, and a total welded length of 3 188 metres. The data were modelled for statistical calculations, and models of welding time were derived by using linear regression analysis. Themodels were tested by using appropriate statistical methods, and were found to be accurate. General welding time models have been developed, valid for welding in Finland, as well as specific, more accurate models for particular companies. The models are presented in such a form that they can be used easily by a designer, enabling the cost calculation to be automated.

Applying the principles of life cycle assessment and costing in process modeling to examine profit-making capability

Static process simulation has traditionally been used to model complex processes for various purposes. However, the use of static processsimulators for the preparation of holistic examinations aiming at improving profit-making capability requires a lot of work because the production of results requires the assessment of the applicability of detailed data which may be irrelevant to the objective. The relevant data for the total assessment gets buried byirrelevant data. Furthermore, the models do not include an examination of the maintenance or risk management, and economic examination is often an extra property added to them which can be performed with a spreadsheet program. A process model applicable to holistic economic examinations has been developed in this work. The model is based on the life cycle profit philosophy developed by Hagberg and Henriksson in 1996. The construction of the model has utilized life cycle assessment and life cycle costing methodologies with a view to developing, above all, a model which would be applicable to the economic examinations of complete wholes and which would require the need for information focusing on aspects essential to the objectives. Life cycle assessment and costing differ from each other in terms of the modeling principles, but the features of bothmethodologies can be used in the development of economic process modeling. Methods applicable to the modeling of complex processes can be examined from the viewpoint of life cycle methodologies, because they involve the collection and management of large corpuses of information and the production of information for the needs of decision-makers as well. The results of the study shows that on the basis of the principles of life cycle modeling, a process model can be created which may be used to produce holistic efficiency examinations on the profit-making capability of the production line, with fewer resources thanwith traditional methods. The calculations of the model are based to the maximum extent on the information system of the factory, which means that the accuracyof the results can be improved by developing information systems so that they can provide the best information for this kind of examinations.

Studies on coordination of systems development process

This thesis examines coordination of systems development process in a contemporary software producing organization. The thesis consists of a series of empirical studies in which the actions, conceptions and artifacts of practitioners are analyzed using a theory-building case study research approach. The three phases of the thesis provide empirical observations on different aspects of systemsdevelopment. In the first phase is examined the role of architecture in coordination and cost estimation in multi-site environment. The second phase involves two studies on the evolving requirement understanding process and how to measure this process. The third phase summarizes the first two phases and concentrates on the role of methods and how practitioners work with them. All the phases provide evidence that current systems development method approaches are too naïve in looking at the complexity of the real world. In practice, development is influenced by opportunity and other contingent factors. The systems development processis not coordinated using phases and tasks defined in methods providing universal mechanism for managing this process like most of the method approaches assume.Instead, the studies suggest that managing systems development process happens through coordinating development activities using methods as tools. These studies contribute to the systems development methods by emphasizing the support of communication and collaboration between systems development participants. Methods should not describe the development activities and phases in a detail level, butshould include the higher level guidance for practitioners on how to act in different systems development environments.

Studies on the characterization of dental whitening process by using both hyperspectral imaging and colorimeter techniques

A beautiful smile is directly related with white teeth. Nowadays oral care has increased and developed processes for beautiful smiles. Dental bleaching is frequently used in odontology, not just for health care also for aesthetic treatment. With the possibility of teeth bleaching, now the importance is in, how white the tooth is? Because color is relate to an individual perception. In order to assets teeth correct color identification has been developed many color guides, models, spaces and analytical methods. Spite all of these useful tools the color interpretation depends on environmental factors, position of the sample in the data acquisition and most importantly the instrument sensitivity. The commons methods have proved to be useful. They are easy to handle, some are portable but they do not have a high sensitivity. The present work is based on the integration of a new analytical technique for color acquisition. High spectral Image (HSI) is able to performed image analysis with high quality and efficiency. HSI is used in many fields and we used it for color image analysis within the bleaching process. The main comparison was done with the HSI and the colorimeter through the processes of two different bleaching protocols. The results showed that HSI has higher sensitivity than the colorimeter. During the analysis the dental surface with the HSI we were able to notice surface changes. These changes were analyzed by roughness studies.

Indol-butyric acid levels on cashew cloning by air-layering process

A study was conducted to determine the possibility of cashew (Anacardium occidentale) cloning by air-layering and influence of IBA (indol-butyric acid) on this process. It was adopted a completely randomized design with 4 treatments, 10 air layers each and 4 replications, reaching 160 air layers. The IBA levels on the treatments were, as follow: 0, 1000, 3000 and 5000 mg.kg-1. It was evaluated: survival, callus and rooting percentage, average number and length of roots. The highest survival rate (67.5%) was registered with no growth regulator and IBA at 1000 mg.kg-1, while the best rooting percentage (82%) referred to 1000 mg.kg-1. In spite of average number and length of roots, the highest results were observed with IBA at 5000 mg.kg-1. IBA concentrations had no influence on cashew air-layering formation.

The biological basis of the aging process

El procés biològic bàsic subjacent de l’envelliment va ésser avançat per la teoria de l’envelliment basada en els radicals lliures l’any 1954: la reacció dels radicals lliures actius, produïts fisiològicament en l’organisme, amb els constituents cel·lulars inicia els canvis associats a l’envelliment. La implicació dels radicals lliures en l’envelliment està relacionada amb el seu paper clau en l’origen i l’evolució de la vida. La informació disponible avui en dia ens mostra que la composició específica de les macromolècules cel·lulars (proteïnes, àcids nucleics, lípids i carbohidrats) en les espècies animals longeves tenen intrínsicament una resistència elevada a la modificació oxidativa, la qual cosa probablement contribueix a la longevitat superior d’aquestes espècies. Les espècies longeves també mostren unes taxes reduïdes de producció de radicals lliures i de lesió oxidativa. D’altra banda, la restricció dietària disminueix la producció de radicals lliures i la lesió molecular oxidativa. Aquests canvis estan directament associats a la reducció de la ingesta de proteïnes dels animals sotmesos a restricció, que alhora sembla que són deguts específicament a la reducció de la ingesta de metionina. En aquesta revisió s’emfatitza que una taxa baixa de generació de lesió endògena i una resistència intrínsecament elevada a la modificació de les macromolècules cel·lulars són trets clau de la longevitat de les espècies animals.

Breaking up the writing process: how wikis can support understanding the composition and revision strategies of young writers

Understanding how best to support immature writers in the development of their understanding of the writing process is an important concern for researchers and teachers. Social technologies have become key features of leisure and work place writing, yet knowledge about how to design educational settings that take full advantage of the affordances of web 2.0 technologies to support early writing is scarce. This paper presents a small scale study that investigated how writing in a wiki environment might facilitate and support students’ use of composition and revision strategies. Our findings show that wiki can enlarge young writers’ experience of the process of composition and revision both through their own efforts and by observing the process in others. In this study students employed a wide range of types of revisions both surface and text based changes. These revisions took place during the process of composition as well as at the end. It is argued here that writing in a wiki not only provides young writers with experience of a mode of composition prevalent in the contemporary work environment, but breaks up the process of writing in a way that may support students’ understanding of the processes of composition and revision.

Translation as a Process and Translation as a Product in Teaching Translation

L'ensenyament de la traducció s'ha utilitzat tradicionalment en algunes titulacions de filologia com a eina d'aprenentatge d'habilitats de la llengua. Aquesta circumstància, però, no ha d'estar renyida amb la producció d'una traducció acceptable. En aquest article es pretén analitzar si pot aconseguir-se aquest objectiu mitjançant la incorporació d'informació extratextual en l'enunciat de l'exercici de traducció. Els resultats obtinguts amb un grup d'estudiants de filologia mostren que en les seves decisions lingüístiques va tenir un pes important el tipus d'informació extratextual adjunta als textes originals anglesos. Si bé caldria fer un esforç investigador més sistemàtic per poder afirmar-ho categòricament, aquest estudi intenta esbossar la qüestió tan discutida de fins on l'aprenentatge d'una llengua s'ha de realitzar junt amb l'aprenentatge de la traducció. Aquest estudi, també, planteja la necessitat d'incorporar informació extratextual en l'aprenentatge de la traducció, independentment de la titulació que en aquests estudis s'insereixen.