Spatial variation of optical and structural properties of ELO GaN directly grown on patterned sapphire by HVPE

A 275 mu m thick GaN layer was directly grown on the SiO2-prepatterned sapphire in a home-built vertical hydride vapour phase epitaxy (HVPE) reactor. The variation of optical and structure characteristics were microscopically identified using spatially resolved cathodeluminescence and micro-Raman spectroscopy in a cross section of the thick film. The D X-0(A) line with the FWHM of 5.1 meV and etch- pit density of 9 x 10(6) cm(-2) illustrated high crystalline quality of the thick GaN epitaxial layer. Optically active regions appeared above the SiO2 masks and disappeared abruptly due to the tapered inversion domains at 210 - 230 mu m thickness. The crystalline quality was improved by increasing the thickness of the GaN/sapphire interface, but the region with a distance of 2 mu m from the top surface revealed relatively low quality due to degenerate surface reconstruction by residual gas reaction. The x-ray rocking curve for the symmetric (0 0 2) and asymmetric (1 0 2) reflections also showed good quality and a small wing tilt of the epitaxial lateral overgrowth (ELO) GaN.

非粮原料燃料乙醇发酵关键技术的研究

生物质燃料乙醇是一种高度清洁的交通液体燃料，是减少温室气体排放，缓解大气污染的最佳技术选择。以非粮原料生产燃料乙醇可以在进行能源生产的同时保证粮食安全，有利于产业的可持续发展。在众多的非粮原料中，甘薯是我国开发潜力最大的生物质能源作物之一。我国占世界甘薯种植总面积和产量的90％。同时，甘薯的单位面积燃料乙醇产量远大于玉米和小麦。其成本是目前酒精中最低廉的，因此利用甘薯生产乙醇是发展生物质燃料乙醇的首要选择。目前采用薯类全原料主要采用分批发酵生产乙醇，其技术水平低，发酵强度低，一般在0.7－2.5g/（L•h），乙醇浓度低，甘薯发酵乙醇为6－8％(v/v)，能耗高，环境负荷大，污染严重。针对上述问题，本文从菌株选育、原料预处理、中试放大、残糖成分分析等方面进行研究。 为了研究乙醇发酵生产规模扩大过程中，大型发酵罐底部高压条件下，CO2对酵母乙醇发酵的影响，我们通过CO2 加压的方法进行模拟试验，研究结果表明，发酵时间随压强的升高而逐渐延长，高压CO2 对乙醇发酵效率影响不大，在0.3 MPa 以下时，发酵效率均可达到90%以上。高压CO2 对发酵的抑制作用是高压和CO2 这两个因素联合作用的结果。高压CO2 条件下，酵母胞外酶和胞内重要酶类的酶活均表现出特征性。0.2 MPa 下，酶活性的变化趋势和0.1 MPa 条件下的较为一致。而0.3 MPa 下的酶活变化趋势与0.4 MPa 下的酶活更为接近。通过全基因表达分析发现在CO2 压力为0.3 MPa 下，乙醇发酵途径中多个基因表达量下调，同时海藻糖合成酶和热激蛋白基因表达量上调。 筛选耐高温的乙醇酵母菌株能够解决糖化温度和发酵温度不协调的矛盾，实现真正意义上的边糖化边发酵。高温发酵还能够降低发酵时的冷却成本，实现乙醇的周年生产。本研究筛选出一株高温发酵菌株Y-H1，进而我们对该菌株的胞外酶和胞内乙醇代谢重要酶类的酶活性进行了分析。结果表明Y-H1 能够在40 ℃条件下正常进行乙醇发酵，发酵33h，最终乙醇浓度达到10.7%（w/w），发酵效率达到90%以上。同时发酵液最终pH 在3.5 左右，显示菌株具有一定的耐酸性能力。同时观察到40 ℃下，菌株的胞外酶和胞内乙醇代谢重要酶类的酶活性发生了变化，乙醇发酵途径中关键酶基因表达下调，而海藻糖合成酶与热激蛋白基因表达量上调，这些结果为进一步研究酵母菌耐热调控机理提供了依据。 糖蜜是一种大规模工业生产乙醇的理想原料，本研究利用选育高浓度乙醇发酵菌株结合配套的发酵稳定剂，研究了糖蜜高浓度乙醇发酵情况。结果表明采用冷酸沉淀预处理糖蜜溶液，采用分批补料的发酵方式，乙醇浓度最高达到了10.26% (w/w)，发酵时间为42 h。同时观察到在糖蜜发酵中，乙醛含量与乙醇浓度存在一定的相关性。 快速乙醇发酵对于缩短乙醇生产周期、降低乙醇生产成本、减少原料腐烂损失具有重要意义。本研究诱变和筛选得到了一株快速乙醇发酵菌株10232B。在优化后的发酵条件下，采用10L 发酵罐进行分批乙醇发酵，经过18h,乙醇的最终浓度达到88.5g/L,发酵效率93.6%，平均乙醇生产速度达到4.92 g/L/h。此菌株在保持较高乙醇生产浓度的同时，拥有快速生产乙醇的能力，适合作为快速乙醇发酵生产菌种。 由于鲜甘薯具有粘度大的特点，传统液化糖化处理很难在短时间内充分糖化原料；高粘度的醪液也难以进行管道输送，容易堵塞管路；同时，也会降低后续的乙醇发酵效率。 本文采用了快速粘度分析法对鲜甘薯糊化粘度特性进行了分析，进而对预处理条件进行了研究，在最佳预处理条件下，糖化2h 后，醪液葡萄糖值最高可达99.3，粘度4.5×104 mPa.s，而采用传统糖化工艺，醪液DE 值仅为85.8，粘度大于1.0×105 mPa.s。 此预处理方法也可用于快速糖化不加水的醪液。后续的乙醇发酵试验表明，通过此预处理方法获得的糖化醪液对乙醇发酵无负面影响。 在前期已实现了实验室水平的鲜甘薯燃料乙醇快速乙醇发酵基础上，进一步将发酵规模扩大到500L，在中试水平上对甘薯乙醇发酵进行了研究。结果表明在500L 中试规模，采用边糖化边发酵（SSF）工艺，在料液比为3∶1，发酵醪液最高粘度为6×104mPa.s 条件下，发酵37h，乙醇浓度达到了12.7%（v/v），发酵效率91%，发酵强度为2.7 g/（L•h）。与目前国内的薯类乙醇发酵生产技术水平具有明显的优越性。 为研究甘薯、木薯乙醇发酵中残糖的组成，采用了高效液相色谱—蒸发光散射检测法，对乙醇发酵残糖进行了分析。结果表明，甘薯、木薯乙醇发酵残糖均为寡聚糖，主要由葡萄糖、木糖、半乳糖、阿拉伯糖和甘露糖构成。随着发酵时间延长，寡聚糖中的葡萄糖、半乳糖、甘露糖可被缓慢的水解释放。提高糖化酶量仅在一定程度上降低残糖，过量的糖化酶反而会导致残糖增加。同时发现3, 5-二硝基水杨酸法不能准确测定甘薯、木薯乙醇发酵中的残总糖含量。进一步筛选了两株残糖降解菌株，对甘薯乙醇发酵残糖的降解利用率均达到了40%以上，而且还能显著降低发酵醪液粘度。经形态学和rRNA ITS 序列分析，确定这两株菌分别属于为木霉属和曲霉属黑曲霉组。 通过对以甘薯原料为代表的非粮原料发酵技术研究开发，以期形成乙醇转化率高，能耗低，生产效率高、季节适应性好，原料适应性广，经济性强，符合清洁生产机制的燃料乙醇高效转化技术，为具有我国特色的燃料乙醇发展模式提供技术支持。 Sweet potato is one of the major feedstock for the fuel ethanol production in China. The planting area and the yield in China take 90% of the world. Sweet potato is an efficient kind of energy crops. The energy outcome per area is higher than corn or wheat. And the manufacture cost of ethanol is the lowest, compared with corn and wheat. So sweet potato is the favorable crop for the bioethanol production in China. However, the low-level fermentation technology restricts the development of ethanol production by sweet potato, including slow ethanol production rate, low ethanol concentration and high energy cost. To solve these problems, we conducted research on the strain breeding, pretreatment, pilot fermentation test and residual saccharides analysis. To study the impact of hyperbaric condition at bottom of the large fermentor on yeast fermentation, high pressure carbon dioxide (CO2) was adopted to simulate the situation. The results showed that the fermentation was prolonged with the increasing pressure. The pressure of CO2 had little impact on the ethanol yield which could reach 90% under the pressure below 0.3 MPa. The inhibition was combined by the high pressure and CO2. Under the high CO2 pressure, the extracellular and important intracellular enzyme activities were different from those under normal state. The changes under 0.1 MPa and 0.2 MPa were similar. The changes under 0.3 MPa were closer to those under 0.4 MPa. The application of thermotolerance yeast could solve the problem of the inconsistent temperature between fermentation and saccharificaton and fulfill the real simultaneous saccharification and fermentation. And it could reduce the cooling cost. A thermotolerance strain Y-H1 was isolated in our research. It gave high ethanol concentration of 10.7%（w/w）at 40 ℃ for 33 h. The ethanol yield efficiency was over 90%. At 40 ℃, the extracellular and important intracellular enzyme activities of Y-H1 showed the difference with normal state, which may indicate its physiological changes at the high temperature. Molasses is another feedstock for industrial ethanol production. By our ethanol-tolerance strain and the regulation reagents, the fermentation with high ethanol concentration was investigated. In fed-batch mode combined with cold acid deposition, the highest ethanol concentration was 10.26% (w/w) for 42h. The aldehyde concentration in fermentation was found to be related to ethanol concentration. The development of a rapid ethanol fermentation strain of Zymomonas mobilis is essential for reducing the cost of ethanol production and for the timely utilization of fresh material that is easily decayed in the Chinese bioethanol industry. A mutant Z. mobilis strain, 10232B, was generated by UV mutagenesis. Under these optimized conditions, fermentation of the mutant Z. mobilis 10232B strain was completed in just 18 h with a high ethanol production rate, at an average of 4.92 gL-1h-1 per batch. The final maximum ethanol concentration was 88.5 gL-1, with an ethanol yield efficiency of 93.6%. This result illustrated the potential use of the mutant Z. mobilis 10232B strain in rapid ethanol fermentation in order to help reduce the cost of industrial ethanol production. As fresh sweet potato syrup shows high viscosity, it is hard to be fully converted to glucose by enzymes in the traditional saccharification process. The high-viscosity syrup is difficult to be transmitted in pipes, which may be easily blocked. Meanwhile it could also reduce the later ethanol fermentation efficiency. To solve these problems, effects of the pretreatment conditions were investigated. The highest dextrose equivalent value of 99.3 and the lowest viscosity of 4.5×104 mPa.s were obtained by the most favorable pretreatment conditions, while those of 85.8 and over 1.0×105 mPa.s was produced by traditional treatment conditions. The pretreatment could also be applied on the material syrup without adding water. The later experiments showed that the pretreated syrup had no negative effect on the ethanol fermentation and exhibited lower viscosity. The fuel ethanol rapid production from fresh sweet potato was enlarged in the 500L pilot scale after its fulfillment on the laboratory level. The optimal ratio of material to water was 3 to 1 in 500L fermentor. With low-temperature-cooking (85 ℃) using SSF, the Saccharomyces cerevisiae was able to produce ethanol 97.44 g/kg for 37h, which reached 92% of theoretical yield. The average ethanol production rate was 4.06 g/kg/h. And the maximum viscosity of syrup reached 6×104mPa.s. The results showed its superiority over current industrial ethanol fermentation. The compositions of the residual saccharides in the ethanol fermentation by sweet potato and cassava were analyzed by high performance liquid chromatography coupled with evaporative light-scattering detector. The results showed that all the residual saccharides were oligosaccharides, mainly composed of glucose, xylose, galactose, arabinose and mannose. The glucose, galactose and mannose could be slowly hydrolyzed from oligosaccharides in syrup during a long period. To increase the glucoamylase dosage could lower the residual saccharides to a certain extent. However, excess glucoamylase dosage led to more residual saccharides. And the method of 3, 5-dinitrosalicylic acid could not accurately quantify the residual total saccharides content. Two residual saccharides degrading strains were isolated, which could utilize 40% of total residual saccharide and lower the syrup viscosity. With the analysis of morphology and internal transcribed spacer sequence, they were finally identified as species of Trichoderma and Aspergillus niger.

Optimization of the HIRFL-CSR cluster target

A new gas delivery system is designed and installed for HIRFL-CSR cluster target. The original blocked nozzle is replaced by a new one with the throat diameter of 0.12mm. New test of hydrogen and argon gases are performed. The stable jets can be obtained for these two operation gases. The attenuation of the jet caused by the collision with residual gas is studied. The maximum achievable H-2 target density is 1.75x10(13) atoms/cm(3) with a target thickness of 6.3x10(12) atoms/cm(2) for HIRFL-CSR cluster target. The running stability of the cluster source is tested both for hydrogen and argon. The operation parameters for obtaining hydrogen jet are optimized. The results of long time running for H-2 and Ar cluster jets look promising. The jet intensity has no essential change during the test for H-2 and Ar.

非拦截式弱束流剖面测量方法的研究----剩余气体束流剖面探测系统的研制

随着加速器束流诊断技术的不断发展，非拦截式束流测量方法及弱束流诊断技术在加速器领域被广泛应用。为了跟踪国际上加速器技术研究前沿，配合HIRFL改造，以满足CSR大科学工程对HIRFL束流品质及调束效率提出的更高要求，本论文开展了弱束流测量方法的研究和一种新型的非拦截式束流位置及剖面探测装置的研制。论文中简要概述了国际国内加速器束流诊断技术的发展现状以及非拦截式弱束流测量技术在加速器中的应用，调研了国际上研制的利用剩余气体获取束流参数的各种束诊设备，为开展本课题的研究奠定了理论基础；论文中重点论述了研制剩余气体束流剖面探测系统的工作原理，利用平行板电极形成的均匀电场收集束流与剩余气体分子碰撞时产生的剩余气体正离子，通过微通道板与连续型电阻阳极构成的位置灵敏探测器将剩余气体正离子放大、读出，最终获得束流位置及剖面等参数；详细介绍了剩余气体束流剖面测量系统的设计，包括机械装置和信号获取系统，机械部分主要由真空测量室、平行板式高压电极和位置灵敏探测器组成，获取系统由电荷灵敏前置放大器、主放大器、加法器、位置灵敏分析器、计算机多道分析系统及符合电路组成；最后给出了离线和在线测试实验分析结果。本论文主要基于剩余气体电离理论，以非拦截式束流探测技术为主导思想，从理论上分析了利用剩余气体测量束流位置及束流剖面的可行性，首次在国内加速器领域研制出剩余气体束流剖面探测装置，并将其应用于重离子加速器实验，初步实验结果证明系统设计结构合理，测量灵敏度，位置分辨及线性基本达到了系统设计要求。本课题的研究无论是对于HIRFL非拦截诊断技术的扩展，还是对于HIRFL-CSR束诊系统的发展都具有深远意义。

Evaluation of a sequential extraction for the speciation of thorium in soils from Baotou area, Inner Mongolia

Sequential extraction procedures were widely applied for speciation of radioactive elements. In this study, the sequential extraction procedure developed by Martinez-Aguirre was employed for quantification of different chemical forms of thorium in the soil. The total amount of thorium in contaminated soil was much higher by four-fold than the local background value. The soil properties affect the amount of thoriurn and distribution of fractions in contaminated soil. Results showed that the proportion of thorium in soils from Baotou was found as the residual fraction (F5 + F6) > absorbed fraction (F3), coprecipitated fraction (F4) > carbonates fraction (172) and exchangeable fraction (F1) that could be available to plants. The recovery, calculated by ratio of the sum of the six fractions to the pseudo-total content of thorium, was in the range from 96% to 110%. A comparison was carried out between the sequential extraction and the single extraction to evaluate the selectivity of the extractants. It was found that the amount of thorium of absorbed fraction (H) was higher in the single extraction than that estimated in the sequential extraction, possibly duo to transform of the labile form. While for non-residual fraction analysis, the single extraction scheme was a desirable alternative to the sequential extraction procedure.

中国大中型气田天然气成藏物理化学模拟研究

Natural gas pays more important role in the society as clean fuel. Natural gas exploration has been enhanced in recent years in many countries. It also has prospective future in our country through "85" and "95" national research. Many big size gas fields have been discovered in different formations in different basins such as lower and upper Paleozoic in Erdos basin, Tertiary system in Kuche depression in Tarim basin, Triassic system in east of Sichuan basin. Because gas bearing basins had been experienced multiple tectogenesis. The characteristics of natural gases usually in one gas field are that they have multiple source rocks and are multiple maturities and formed in different ages. There has most difficult to research on the gas-rock correlation and mechanism of gas formation. Develop advanced techniques and methods and apply them to solve above problems is necessary. The research is focused on the critical techniques of geochemistry and physical simulation of gas-rock correlation and gas formation. The lists in the following are conclusions through research and lots of experiments. I 8 advanced techniques have been developed or improved about gas-rock correlation and gas migration, accumulation and formation. A series of geochemistry techniques has been developed about analyzing inclusion enclave. They are analyzing gas and liquid composition and biomarker and on-line individual carbon isotope composition in inclusion enclave. These techniques combing the inclusion homogeneous temperature can be applied to study on gas-rock correlation directly and gas migration, filling and formation ages. Technique of on-line determination individual gas carbon isotope composition in kerogen and bitumen thermal pyrolysis is developed. It is applied to determine the source of natural is kerogen thermal degradation or oil pyrolysis. Method of on-line determination individual gas carbon isotope composition in rock thermal simulation has being improved. Based on the "95"former research, on-line determination individual gas carbon isotope composition in different type of maceral and rocks thermal pyrolys is has been determined. The conclusion is that carbon isotope composition of benzene and toluene in homogenous texture kerogen thermal degradation is almost same at different maturity. By comparison, that in mixture type kerogen thermal pyrolysis jumps from step to step with the changes of maturity. This conclusion is a good proof of gas-rock dynamic correlation. 3. Biomarker of rock can be determined directly through research. It solves the problems such as long period preparing sample, light composition losing and sample contamination etc. It can be applied to research the character of source rock and mechanism of source rock expulsion and the path of hydrocarbon migration etc. 4. The process of hydrocarbon dynamic generation in source rock can be seen at every stage applying locating observation and thermal simulation of ESEM. The mechanism of hydrocarbon generation and expulsion in source rock is discussed according to the experiments. This technique is advanced in the world. 5. A sample injection system whose character is higher vacuum, lower leaks and lower blank has been built up to analyze inert gas. He,Ar,Kr and Xe can be determined continuously on one instrument and one injection. This is advanced in domestic. 7. Quality and quantity analysis of benzene ring compounds and phenolic compounds and determination of organic acid and aqueous gas analysis are applied to research the relationship between compounds in formation water and gas formation. This is another new idea to study the gas-rock correlation and gas formation. 8. Inclusion analysis data can be used to calculate the Paleo-fluid density, Paleo-geothermal gradient and Paleo-geopressure gradient and then to calculate the Paleo-fluid potential. It's also a new method to research the direction of hydrocarbon migration and accumulation. 9. Equipment of natural gas formation simulation is produced during the research to probe how the physical properties of rock affect the gas migration and accumulation and what efficiency of gas migrate and factors of gas formation and the models of different type of migration are. II study is focused on that if the source rocks of lower Paleozoic generated hydrocarbon and what the source rocks of weathered formation gas pool and the mechanism of gas formation are though many advanced techniques application. There are four conclusions. 1.The maturity of Majiagou formation source rocks is higher in south than that in north. There also have parts of the higher maturity in middle and east. Anomalous thermal pays important role in big size field formation in middle of basin. 2. The amount of gas generation in high-over maturity source rocks in lower Paleozoic is lager than that of most absorption of source rocks. Lower Paleozoic source rocks are effective source rocks. Universal bitumen exists in Ordovician source rocks to prove that Ordovician source rocks had generated hydrocarbon. Bitumen has some attribution to the middle gas pool formation. 3. Comprehensive gas-rock correlation says that natural gases of north, west, south of middle gas field of basin mainly come from lower Paleozoic source rocks. The attribution ratio of lower Paleozoic source rocks is 60%-70%. Natural gases of other areas mainly come from upper Paleozoic. The attribution ratio of upper Paleozoic source rocks is 70%. 4. Paleozoic gases migration phase of Erdos basin are also interesting. The relative abundance of gasoline aromatic is quite low especially toluene that of which is divided by that of methyl-cyclohexane is less than 0.2 in upper Paleozoic gas pool. The migration phase of upper Paleozoic gas may be aqueous phase. By comparison, the relative abundance of gasoline aromatic is higher in lower Paleozoic gas. The distribution character of gasoline gas is similar with that in source rock thermal simulation. The migration phase of it may be free phase. IH Comprehensive gas-rock correlation is also processed in Kuche depression Tarim basin. The mechanism of gas formation is probed and the gas formation model has been built up. Four conclusions list below. 1. Gases in Kuche depression come from Triassic-Jurassic coal-measure source rocks. They are high-over maturity. Comparatively, the highest maturity area is Kelasu, next is Dabei area, Yinan area. 2. Kerogen thermal degradation is main reason of the dry gas in Kuche depression. Small part of dry gas comes from oil pyrolysis. VI 3.The K12 natural gas lays out some of hydro-gas character. Oil dissolved in the gas. Hydro-gas is also a factor making the gas drier and carbon isotope composition heavier. 4. The mechanism and genesis of KL2 gas pool list as below. Overpressure has being existed in Triassic-Jurassic source rocks since Keche period. Natural gases were expulsed by episode style from overpressure source rocks. Hetero-face was main migration style of gas, oil and water at that time. The fluids transferred the pressure of source rocks when they migrated and then separated when they got in reservoir. After that, natural gas migrated up and accumulated and formed with the techno-genesis. Tectonic extrusion made the natural gas overpressure continuously. When the pressure was up to the critical pressure, the C6-C7 composition in natural gas changed. The results were that relative abundance of alkane and aromatic decreased while cycloalkane and isoparaffin increased. There was lots of natural gas filling during every tectonic. The main factors of overpressure of natural gas were tectonic extrusion and fluid transferring pressure of source rocks. Well preservation was also important in the KL2 gas pool formation. The reserves of gas can satisfy the need of pipeline where is from west to east. IV A good idea of natural gas migration and accumulation modeling whose apparent character is real core and formation condition is suggested to model the physical process of gas formation. Following is the modeling results. 1. Modeling results prove that the gas accumulation rule under cap layer and gas fraction on migration path. 2. Natural gas migration as free phase is difficult in dense rock. 3. Natural gases accumulated easily in good physical properties reservoirs where are under the plugging layer. Under the condition of that permeability of rock is more than 1 * 10~(-3)μm~(-1), the more better the physical properties and the more bigger pore of rock, the more easier the gas accumulation in there. On the contrary, natural gas canonly migrate further to accumulate in good physical properties of rock. 4. Natural gas migrate up is different from that down. Under the same situation, the amount of gas migration up is lager than that of gas migration down and the distance of migration up is 3 times as that of migration down. 5. After gas leaks from dense confining layer, the ability of its dynamic plug-back decreased apparently. Gas lost from these arils easily. These confining layer can confine again only after geology condition changes. 6. Water-wetted and capillary-blocking rocks can't block water but gases generally. The result is that water can migrate continuously through blocking rocks but the gases stay under the blocking rocks then form in there. The experiments have proved the formation model of deep basin gas.

Bactericidal/permeability-increasing protein attenuates systemic inflammation and acute lung injury in porcine lower limb ischemia-reperfusion injury.

OBJECTIVE: To investigate the role of recombinant bactericidal/permeability-increasing protein (rBPI21) in the attenuation of the sepsis syndrome and acute lung injury associated with lower limb ischemia-reperfusion (I/R) injury. SUMMARY BACKGROUND DATA: Gut-derived endotoxin has been implicated in the conversion of the sterile inflammatory response to a lethal sepsis syndrome after lower torso I/R injury. rBPI21 is a novel antiendotoxin therapy with proven benefit in sepsis. METHODS: Anesthetized ventilated swine underwent midline laparotomy and bilateral external iliac artery occlusion for 2 hours followed by 2.5 hours of reperfusion. Two groups (n = 6 per group) were randomized to receive, by intravenous infusion over 30 minutes, at the start of reperfusion, either thaumatin, a control-protein preparation, at 2 mg/kg body weight, or rBPI21 at 2 mg/kg body weight. A control group (n = 6) underwent laparotomy without further treatment and was administered thaumatin at 2 mg/kg body weight after 2 hours of anesthesia. Blood from a carotid artery cannula was taken every half-hour for arterial blood gas analysis. Plasma was separated and stored at -70 degrees C for later determination of plasma tumor necrosis factor (TNF)-alpha, interleukin (IL)-6 by bioassay, and IL-8 by enzyme-linked immunosorbent assay (ELISA), as a markers of systemic inflammation. Plasma endotoxin concentration was measured using ELISA. Lung tissue wet-to-dry weight ratio and myeloperoxidase concentration were used as markers of edema and neutrophil sequestration, respectively. Bronchoalveolar lavage protein concentration was measured by the bicinclinoic acid method as a measure of capillary-alveolar protein leak. The alveolar-arterial gradient was measured; a large gradient indicated impaired oxygen transport and hence lung injury. RESULTS: Bilateral hind limb I/R injury increased significantly intestinal mucosal acidosis, intestinal permeability, portal endotoxemia, plasma IL-6 concentrations, circulating phagocytic cell priming and pulmonary leukosequestration, edema, capillary-alveolar protein leak, and impaired gas exchange. Conversely, pigs treated with rBPI21 2 mg/kg at the onset of reperfusion had significantly reduced intestinal mucosal acidosis, portal endotoxin concentrations, and circulating phagocytic cell priming and had significantly less pulmonary edema, leukosequestration, and respiratory failure. CONCLUSIONS: Endotoxin transmigration across a hyperpermeable gut barrier, phagocytic cell priming, and cytokinemia are key events of I/R injury, sepsis, and pulmonary dysfunction. This study shows that rBPI21 ameliorates these adverse effects and may provide a novel therapeutic approach for prevention of I/R-associated sepsis syndrome.

Simulation of a collisionless planar electrostatic shock in a proton-electron plasma with a strong initial thermal pressure change

The localized deposition of the energy of a laser pulse, as it ablates a solid target, introduces high thermal pressure gradients in the plasma. The thermal expansion of this laser-heated plasma into the ambient medium (ionized residual gas) triggers the formation of non-linear structures in the collisionless plasma. Here an electron-proton plasma is modelled with a particle-in-cell simulation to reproduce aspects of this plasma expansion. A jump is introduced in the thermal pressure of the plasma, across which the otherwise spatially uniform temperature and density change by a factor of 100. The electrons from the hot plasma expand into the cold one and the charge imbalance drags a beam of cold electrons into the hot plasma. This double layer reduces the electron temperature gradient. The presence of the low-pressure plasma modifies the proton dynamics compared with the plasma expansion into a vacuum. The jump in the thermal pressure develops into a primary shock. The fast protons, which move from the hot into the cold plasma in the form of a beam, give rise to the formation of phase space holes in the electron and proton distributions. The proton phase space holes develop into a secondary shock that thermalizes the beam.

DITRANS - a multi-agent system for integrated diagnosis of power transformers

This paper describes the development and the implementation of a multi-agent system for integrated diagnosis of power transformers. The system is divided in layers which contain a number of agents performing different functions. The social ability and cooperation between the agents lead to the final diagnosis and to other relevant conclusions through integrating various monitoring technologies, diagnostic methods and data sources, such as the dissolved gas analysis.

Previsão de avarias em transformadores de potência através da análise de ensaios físico-químicos

Os Transformadores de potência são máquinas de elevada importância ao nível dos Sistemas Elétricos de Energia (SEE) uma vez que são estas máquinas que possibilitam a interligação dos diferentes níveis de tensão da rede e a transmissão de energia elétrica em Corrente Alternada (CA). Geralmente, estas máquinas são de grandes dimensões e de elevado nível de complexidade construtiva. Caracterizam-se por possuírem períodos de vida útil bastante elevados (vinte a trinta anos) e preços elevados, o que conduz a um nível de exigência de fiabilidade muito elevada, uma vez que não e viável a existência de muitos equipamentos de reserva nos SEE. Com o objetivo de tentar maximizar o período de vida útil dos transformadores de potência e a sua fiabilidade, tenta-se, cada vez mais, implementar conceitos de manutenção preventiva a este tipo de máquinas. No entanto, a gestão da sua vida útil e extremamente complexa na medida em que, estas máquinas têm vários componentes cruciais e suscetiveis de originar falhas e, quase todos eles, encontram-se no interior de uma cuba. Desta forma, não e possível obter uma imagem do seu estado, em tempo real, sem colocar o transformador fora de serviço, algo que acarreta custos elevados. Por este motivo, desenvolveu-se uma técnica que permite obter uma indicação do estado do transformador, em tempo real, sem o retirar de serviço, colhendo amostras do óleo isolante e procedendo a sua análise físico-química e Analise Gases Dissolvidos (DGA). As análises aos óleos isolantes tem vindo a adquirir uma preponderância muito elevada no diagnóstico de falhas e na analise do estado de conservação destes equipamentos tendo-se desenvolvido regras para interpretação dos parâmetros dos óleos com carácter normativo. Considerando o conhecimento relativo a interpretação dos ensaios físico-químicos e DGA ao oleol, e possível desenvolver ferramentas capazes de otimizar essas mesmas interpretações e aplicar esse conhecimento no sentido de prever a sua evolução, assim como o surgimento de possíveis falhas em transformadores, para assim otimizar os processos de manutenção. Neste campo as Redes Neuronais Artificiais (RNAs) têm um papel fundamental

L'argon : utilisations, toxicité et stratégie analytique en toxicologie médicolégale

Bien qu'intrinsèquement non toxiques, les gaz nobles comme l'argon entraînent à fortes concentrations une déplétion d'oxygène pouvant mener jusqu'à l'asphyxie. Si l'argon se retrouve dans la circulation générale, celui-ci peut même être responsable d'embolies parfois fatales. Cependant, les propriétés d'inerties physicochimiques de ce gaz le rendent très utile dans de nombreuses applications actuelles. Ces applications étant en constante augmentation, il n'est pas rare d'observer proportionnellement des intoxications parfois létales liées à ce gaz. Ainsi, devant le manque d'harmonisation des prélèvements d'échantillons biologiques afin de mettre en évidence de telles intoxications aux gaz nobles et devant l'augmentation du nombre de cas, il devient nécessaire d'établir un état des lieux sur l'utilisation de l'argon, sa toxicité et la stratégie analytique à adopter dans le contexte médico-légal.

La désaturation cérébrale lors d’une chirurgie thoracique : son incidence et sa corrélation avec les complications post opératoires

La ventilation unipulmonaire (SLV; Single Lung Ventilation) pendant les chirurgies thoraciques entraîne des altérations cardio-pulmonaires et hémodynamiques importantes. L’objectif de ce projet de recherche consiste à étudier l’impact de la SLV sur l’oxymétrie cérébrale et sa relation avec les complications post opératoires. La première étude inclut vingt patients ayant subi une chirurgie thoracique nécessitant une SLV. L’oxymétrie a été mesurée à l’aide de l’oxymètre cérébral absolu FORESIGHTTM (CASMED, USA) afin d’étudier les changements de la saturation cérébrale absolue (SctO2) tout le long de la chirurgie. La SctO2 ainsi que les paramètres de monitorage standard (BIS, SpO2, pression sanguine, fréquence cardiaque) ont été notés à toutes les cinq minutes à partir de l’induction jusqu’au réveil. Une analyse sanguine (paO2, paCO2, Hb) a été effectuée à toutes les quinze minutes. La deuxième étude effectuée consistait d’étudier la relation entre la désaturation cérébrale en oxygène et les complications post opératoires. Pour cette fin, les scores Clavien et SOFA mesurant l’amplitude des complications, ont été établis pour chaque patient. Les données sont présentées sous forme de moyenne et de la médiane [1er quartile, 3ème quartile; min – max]. Les vingt patients de la première étude ont montré une valeur moyenne absolue de saturation cérébrale absolue (SctO2) de 80% avant l’induction. Durant la SLV, cette valeur a chuté jusqu’à 63% et est remontée à 71% directement après extubation. Tous ces patients ont subi une désaturation durant SLV de plus que 15% comparativement à la valeur de base et 70% ont eu une désaturation de plus de 20%. La désaturation n’a pas été corrélée avec aucun des paramètres de monitorage clinique standard comme la pression artérielle, les analyses des gaz artériels, la saturation périphérique ou la PaO2. La deuxième étude incluant trente autres patients aux vingt premiers, est venue confirmer les résultats de la première étude. De plus, une analyse de corrélation entre les valeurs minimales de SctO2 obtenues durant SLV et les complications post opératoires a été effectuée. Les patients avaient une SctO2 de base de 80%, qui a chuté jusqu’à 64% pendant la SLV pour récupérer à 71% avant la fin de la chirurgie. 82% des patients ont subi des désaturations de plus de 15% des valeurs initiales et 10% ont atteint des valeurs de SctO2 entre 45 et 55%. Les valeurs minimales de SctO2 observées durant la SLV corrélaient avec le score SOFA non respiratoire (R2=0,090, p=0,0287) ainsi qu’avec le score Clavien (R2=0,098, p=0,0201), mais ne corrélait avec aucun des paramètres cliniques standards (ex : SpO¬2, PaO2, PaCO2, Hb). En définissant une valeur seuil de SctO2=65%, le «Odds ratio» d’avoir une défaillance d’organe non respiratoire est de 2.37 (IC 95%=1,18 – 4,39, p=0,043) et d’avoir une complication classifiée supérieure à un score Clavien de 0 est de 3,19 (IC 95%=1,6 – 6,34, p=0,0272). Les chirurgies thoraciques avec une SLV sont associées à des chutes significatives de SctO2, et les valeurs minimales de SctO2 semblent avoir une corrélation positive avec les complications post opératoires.

Zur Adsorption und Reaktion von Stickstoffmonoxid an Aktivkohle

Die Verwendung von Aktivkohlen und -koksen stellt eine Alternative zu herkömmlichen Prozessen zur Verminderung der NOx-Emissionen in Rauchgasen dar. An diesen Materialien wird Stickstoffmonoxid adsorbiert und katalytisch zu N2 reduziert. Eine einheitliche Erklärung über die ablaufenden Vorgänge und die Reaktionsmechanismen gibt es noch nicht. Die Ergebnisse der bisher veröffentlichten wissenschaftlichen Arbeiten sind sehr unterschiedlich, wenn nicht sogar widersprüchlich. In dieser Arbeit wird, anhand der Messung von NO-Durchbruchskurven und thermischen Desorptionsspektren, die Adsorption und Reaktion von Stickstoffmonoxid an Aktivkohlen und -koksen in Anwesenheit von Sauerstoff und Wasserdampf untersucht. Zur Durchführung der experimentellen Untersuchungen wird eine Versuchsanlage, bestehend aus einer Vorrichtung zur Gasgemischaufbereitung, einem Festbettreaktor und einer Gasanalytik, konzipiert und aufgebaut. Die Untersuchungen erfolgen bei Temperaturen zwischen 100 und 150 °C. Die NO-, O2- und H2O-Konzentrationen werden anhand der Rauchgaszusammensetzung kohlegefeuerter Kraftwerke gewählt. Die experimentellen Untersuchungen konzentrieren sich auf die Verwendung einer Aktivkohle aus Ölpalmschalen, die in einem Drehrohrreaktor am Institut für Thermische Energietechnik der Universität Kassel hergestellt wurde. Die experimentellen Ergebnisse zeigen, dass während des Prozesses NO-Adsorption, -Reduktion und -Oxidation, NO2-Bildung, -Adsorption und -reduktive Desorption, H2O-Adsorption sowie O2-Vergasung gleichzeitig stattfinden. Bei niedrigen Temperaturen werden die NO2-Bildung und die Adsorption bevorzugt. Die NO-Reduktion läuft über adsorbiertes NO mit CO2- und CO-Bildung. Durch O2-Vergasung werden aktive freie Cf-Plätzen für die NO-Reaktion und -Adsorption gebildet. Wasserdampf wird an der Aktivkohle adsorbiert und belegt aktive Plätze für diese Prozesse. Aus den experimentellen Ergebnissen werden kinetische und Gleichgewichtsparameter der NO-Sorption bestimmt. Ein vereinfachtes mathematisches Modell des Festbettreaktors, das zur Berechnung der NO-Durchbruchskurven bei unterschiedlichen Temperaturen dient, wird aufgestellt.

Concordancia en la interpretación de los gases arteriales entre residentes de medicina de emergencias y el intensivista

Se desconoce en la actualidad en Colombia la calidad de la interpretación de los gases arteriales por parte de los residentes de medicina de emergencias. Los gases arteriales es una de las ayudas diagnósticas de más rápida consecución en el servicio de urgencias y más utilizadas por ser indispensable en la valoración de patologías de alta prevalencia como son las enfermedades respiratorias y la sepsis. Su mala interpretación puede llevar a mal direccionamiento del manejo de pacientes en estado crítico por lo que es indefectible que los residentes logren un buen entrenamiento en la interpretación de los mismos. Por esta razón se realiza este estudio analítico de concordancia con recolección prospectiva, de corte transversal que busca determinar el grado de concordancia en la interpretación de gases arteriales de los residentes del programa de Medicina de Emergencias de la Universidad del Rosario y especialista en cuidado crítico, así como la interpretación entre ellos según su nivel de entrenamiento y describir cuáles son los hallazgos que encuentran en la interpretación de los mismos. Se recolectaron 60 gases arteriales realizados a paciente hospitalizados en la unidad de cuidados intensivos de la Fundación Santa Fe de Bogotá y se halló la concordancia entre la lectura de los residentes del programa de Medicina de Emergencias y un intensivista. Encontrando una concordancia moderada (r 0.445 y 0.442, ) en las respuestas identificadas en los residentes de segundo y tercer año de residencia(p:0,000y0,01).(MESH: Blood Gas Análisis, Emergency Medical Services, Education, Medical, Graduate)