A surface characterisation and microstructural study by scanning electron microscopy of the N-methyl-n-alkylpyrrolidinium tetrafluoroborate organic salts

A microstructural characterisation of the family of N-methyl-N-alkylpyrrolidinium tetrafluoroborate organic salts was carried out by observation of powder surface morphologies with the aim of extending the microstructure-property correlation. Inherent difficulties limiting extensive studies of organic solids by SEM, including volatility under vacuum, charging due to electron beam irradiation, and air-sensitivity were overcome with the use of a Field Emission SEM and cryostage attachment. This technique, providing considerable improvements in image quality at low accelerating voltages, enabled direct observation of complex microstructural features in samples exhibiting high temperature plastic crystalline phases (N,N-dimethylpyrrolidinium tetrafluoroborate [P11BF4]; N-methyl-N-ethylpyrrolidinium tetrafluoroborate [P12BF4]; N-methyl-N-propylpyrrolidinium tetrafluoroborate [P13BF4]). Extensive lattice imperfections including grain boundaries, slip planes and dislocation pits were observed within particles of approximately 200 mgrm diameter. The N-methyl-N-butylpyrrolidinium tetrafluoroborate (P14BF4) sample in this series revealed columnar single crystals with high aspect ratios. The origin of plastic flow properties is discussed using single crystal and polycrystalline slip observations and a relationship proposed between defect characteristics and transport properties.

Thermal and physical properties of an archetypal organic ionic plastic crystal electrolyte

The thermal and mechanical properties of the ionic plastic crystal N-methyl-N-propylpyrrolidinium hexafluorophosphate have been investigated and the effect of adding a miscible polymer on the mechanical properties is reported. The physical properties of the pure plastic crystal are discussed in detail and for the first time the change in volume with temperature for an organic ionic plastic crystal is reported. An increase in volume in conjunction with increased conductivity supports the hypothesis that ion conduction within the plastic crystal proceeds via defects. For phase I and melting, the magnitude of the volume increase does not appear to be in accord with the subtle change in conductivity. This is suggested to be due to the presence of layer defects, which allow for correlated ionic motion, which does not increase the conductivity. Addition of polymer to the plastic crystal significantly increases the mechanical strength, decreases the conductivity, but has little effect on the phase behaviour, further supporting the hypothesis of vacancy-mediated conduction.

Surprising effect of nanoparticle inclusion on ion conductivity in a lithium doped organic ionic plastic crystal

Doping lithium bis(trifluoromethanesulfonyl)amide (Li[NTf₂]) into the N-ethyl,N′-methylpyrrolidinium bis(trifluoromethanesulfonyl)amide ([C₂mpyr][NTf₂]) plastic crystal material has previously indicated order of magnitude enhancements in ion transport and conductivity over pure [C₂mpyr][NTf₂]. Recently, conductivity enhancements in this ionic plastic crystal induced by SiO₂ nanoparticles have also been reported. In this work the inclusion of SiO₂ nanoparticles in Li ion doped [C₂mpyr][NTf₂] has been investigated over a wide temperature range by differential scanning calorimetry (DSC), impedance spectroscopy, positron annihilation lifetime spectroscopy (PALS), Raman spectroscopy, NMR spectroscopy and scanning electron microscopy (SEM). Solid state ¹H NMR indicates that the addition of the nanoparticles increases the mobility of the [C₂mpyr] cation and positron lifetime spectroscopy (PALS) measurements indicate an increase in mean defect size and defect concentration as a result of nanoparticle inclusion, especially with 10 wt% SiO₂. Thus, the substantial drop in ion conductivity observed for this doped nanocomposite material was surprising. This decrease is most likely due to the decrease in mobility of the [NTf₂] anion, possibly by its adsorption at the SiO₂/grain boundary interface and concomitant decrease in mobility of the Li ion.

Lithium-functionalised silica nanoparticles for enhanced ionic conductivity in an organic ionic plastic crystal

Addition of silica nanoparticles functionalised with lithium propane sulfonate to the organic ionic plastic crystal N-ethyl-N-methylpyrrolidinium bis(trifluoromethanesulfonyl)amide ([C₂mpyr][NTf₂]) results in a significant increase in ionic conductivity. Analysis of these nanocomposites by impedance spectroscopy, NMR, positron annihilation lifetime spectroscopy (PALS) and Raman spectroscopy suggests that this is the result of higher matrix mobility due to an increase in defect size and concentration. The effect of these functionalised nanoparticles is compared to that previously observed for unfunctionalised nanoparticles in the lithium-doped and pure plastic crystal.

Unusual phase behaviour of the organic ionic plastic crystal N,N-dimethylpyrrolidinium tetrafluoroborate

Analysis of N,N-dimethylpyrrolidinium tetrafluoroborate by ¹H and ¹¹B NMR, Raman spectroscopy and powder XRD shows that this organic ionic plastic crystal material exhibits unusual phase behaviour. ¹H NMR analysis indicates that the mobility of the pyrrolidinium cation decreases when the material is heated into phase I, while the X-ray diffraction pattern changes from a simple, one peak structure in phase II to a more complex pattern in phase I. The possible origins of these unusual transitions are discussed.

Lithium doped N,N-dimethyl pyrrolidinium tetrafluoroborate organic ionic plastic crystal electrolytes for solid state lithium batteries

The organic ionic plastic crystal material N,N-dimethyl pyrrolidinium tetrafluoroborate ([C1mpyr][BF4]) has been mixed with LiBF4 from 0 to 8 wt% and shown to exhibit enhanced ionic conductivity, especially in the higher temperature plastic crystal phases (phases II and I). The materials retain their solid state well above 100 °C with the melt not being observed up to 300 °C. Interestingly the conductivity enhancement is highest with the lowest level of LiBF4 addition in phase II, but then the order of enhancement is reversed in phase I. In all cases, a conductivity drop is observed at the II → I phase transition (105 °C) which is associated with increased order in the pure matrix, as previously reported, although the conductivity drop is least for the highest LiBF4 amount (8 wt%). The 8 wt% sample displays different conductivity behaviours compared to the lower LiBF4 concentrations, with a sharp increase above 50 °C, which is apparently not related to the formation of an amorphous phase, based on XRD data up to 120 °C. Symmetric cells, Li/OIPC/Li, were prepared and cycled at 50 °C and showed evidence of significant preconditioning with continued cycling, leading to a lower over-potential and a concomitant decrease in the cell resistivity as measured by EIS. An SEM investigation of the Li/OIPC interfaces before and after cycling suggested significant grain refinement was responsible for the decrease in cell resistance upon cycling, possibly as a result of an increased grain boundary phase.

An organic ionic plastic crystal electrolyte based on the triflate anion exhibiting high proton transport

A novel organic ionic plastic crystal (OIPC) electrolyte based on a quaternary ammonium cation and the triflate anion has been synthesized, which shows fast proton transport and high thermal stability in the solid state when doped with triflic acid.

Organic ionic plastic crystal electrolytes; a new class of electrolyte for high efficiency solid state dye-sensitized solar cells

Dye-sensitized solar cells are an increasingly promising alternative to conventional silicon solar cells as a method of converting solar energy to electricity and thus providing an effectively inexhaustible energy source. However, the most efficient of these devices currently utilize liquid electrolytes, which suffer from the associated problems of leakage and evaporation. Hence, significant research is currently focused on the development of solid state alternatives. Here we report a new class of solid state electrolyte for these devices, organic ionic plastic crystal electrolytes, that allow relatively rapid diffusion of the redox couple through the matrix, which is critical to the cell performance. A range of different organic ionic plastic crystal materials, utilizing different cation and anion structures, have been investigated and the conductivities, diffusion rates and photovoltaic performance of the electrolytes are reported. The best material, utilizing the dicyanamide anion, achieves efficiencies of more than 5%.

Thin and flexible solid-state organic ionic plastic crystal-polymer nanofibre composite electrolytes for device applications

All solid-state organic ionic plastic crystal–polymer nanofibre composite electrolytes are described for the first time. The new composite materials exhibit enhanced conductivity, excellent thermal, mechanical and electrochemical stability and allow the production of optically transparent, free-standing, flexible, thin film electrolytes (10’s lms thick) for application in electrochemical devices. Stable cycling of a lithium cell incorporating the new composite electrolyte is demonstrated, including cycling at lower temperatures than previously possible with the pure material.

Organic Solvent-Based Graphene Oxide Liquid Crystals: A Facile Route toward the Next Generation of Self-Assembled Layer-by-Layer Multifunctional 3D Architectures

We introduce soft self-assembly of ultralarge liquid crystalline (LC) graphene oxide (GO) sheets in a wide range of organic solvents overcoming the practical limitations imposed on LC GO processing in water. This expands the number of known solvents which can support amphiphilic self-assembly to ethanol, acetone, tetrahydrofuran, N-dimethylformamide, N-cyclohexyl-2-pyrrolidone, and a number of other organic solvents, many of which were not known to afford solvophobic self-assembly prior to this report. The LC behavior of the as-prepared GO sheets in organic solvents has enabled us to disperse and organize substantial amounts of aggregate-free single-walled carbon nanotubes (SWNTs, up to 10 wt %) without compromise in LC properties. The as-prepared LC GO-SWNT dispersions were employed to achieve self-assembled layer-by-layer multifunctional 3D hybrid architectures comprising SWNTs and GO with unrivalled superior mechanical properties (Young’s modulus in excess of 50 GPa and tensile strength of more than 500 MPa).

An organic ionic plastic crystal electrolyte for rate capability and stability of ambient temperature lithium batteries

Reliable, safe and high performance solid electrolytes are a critical step in the advancement of high energy density secondary batteries. In the present work we demonstrate a novel solid electrolyte based on the organic ionic plastic crystal (OIPC) triisobutyl(methyl)phosphonium bis(fluorosulfonyl)imide (P1444FSI). With the addition of 4 mol% LiFSI, the OIPC shows a high conductivity of 0.26 mS cm-1 at 22 °C. The ion transport mechanisms have been rationalized by compiling thermal phase behaviour and crystal structure information obtained by variable temperature synchrotron X-ray diffraction. With a large electrochemical window (ca. 6 V) and importantly, the formation of a stable and highly conductive solid electrolyte interphase (SEI), we were able to cycle lithium cells (LiLiFePO4) at 30 °C and 20 °C at rates of up to 1 C with good capacity retention. At the 0.1 C rate, about 160 mA h g-1 discharge capacity was achieved at 20 °C, which is the highest for OIPC based cells to date. It is anticipated that these small phosphonium cation and [FSI] anion based OIPCs will show increasing significance in the field of solid electrolytes.