Development of a sequential injection chromatography (SIC) method for determination of simazine, atrazine, and propazine

This paper describes the development of a sequential injection chromatography (SIC) procedure for separation and quantification of the herbicides simazine, atrazine, and propazine exploring the low backpressure of a 2.5 cm long monolithic C(18) column. The separation of the three compounds was achieved in less than 90 s with resolution > 1.5 using a mobile phase composed by ACN/1.25 mmol/L acetate buffer (pH 4.5) at the volumetric ratio of 35:65 and flow rate of 40 mu L/s. Detection was made at 223 nm using a flow cell with 40 mm of optical path length. The LOD was 10 mu g/L for the three triazines and the quantification limits were of 30 mu g/L for simazine and propazine and 40 mu g/L for atrazine. The sampling frequency is 27 samples per hour, consuming 1.1 mL of ACN per analysis. The proposed methodology was applied to spiked water samples and no statistically significant differences were observed in comparison to a conventional HPLC-UV method. The major metabolites of atrazine and other herbicides did not interfere in the analysis, being eluted from the column either together with the unretained peak, or at retention times well-resolved from the studied compounds.

Flow injection analysis using carbon film resistor electrodes for amperometric determination of ambroxol

Flow injection analysis (FIA) using a carbon film sensor for amperometric detection was explored for ambroxol analysis in pharmaceutical formulations. The specially designed flow cell designed in the lab generated sharp and reproducible current peaks, with a wide linear dynamic range from 5 x 10(-7) to 3.5 x 10(-4) mol L-1, in 0.1 mol L-1 sulfuric acid electrolyte, as well as high sensitivity, 0.110 A mol(-1) L cm(-2) at the optimized flow rate. A detection limit of 7.6 x 10(-8) mol L-1 and a sampling frequency of 50 determinations per hour were achieved, employing injected volumes of 100 mu L and a flow rate of 2.0 mL min(-1). The repeatability, expressed as R.S.D. for successive and alternated injections of 6.0 x 10(-6) and 6.0 x 10(-5) mol L-1 ambroxol solutions, was 3.0 and 1.5%, respectively, without any noticeable memory effect between injections. The proposed method was applied to the analysis of ambroxol in pharmaceutical samples and the results obtained were compared with UV spectrophotometric and acid-base titrimetric methods. Good agreement between the results utilizing the three methods and the labeled values was achieved, corroborating the good performance of the proposed electrochemical methodology for ambroxol analysis. (C) 2008 Elsevier B.V. All rights reserved.

Simultaneous analysis of five antidepressant drugs using direct injection of biofluids in a capillary restricted-access media-liquid chromatography-tandem mass spectrometry system

Direct analysis, with minimal sample pretreatment, of antidepressant drugs, fluoxetine, imipramine, desipramine, amitriptyline, and nortriptyline in biofluids was developed with a total run time of 8 min. The setup consists of two HPLC pumps, injection valve, capillary RAM-ADS-C18 pre-column and a capillary analytical C 18 column connected by means of a six-port valve in backflush mode. Detection was performed with ESI-MS/MS and only 1 mu m of sample was injected. Validation was adequately carried out using FLU-d(5) as internal standard. Calibration curves were constructed under a linear range of 1-250 ng mL(-1) in plasma, being the limit of quantification (LOQ), determined as 1 ng mL(-1), for all the analytes. With the described approach it was possible to reach a quantified mass sensitivity of 0.3 pg for each analyte (equivalent to 1.1-1.3 fmol), translating to a lower sample consumption (in the order of 103 less sample than using conventional methods). (C) 2008 Elsevier B.V. All rights reserved.

Estudo do processo de combustão in-situ em reservatórios maduros de óleos médios e leves (high pressure air injection)

Nearly 3 x 1011 m3 of medium and light oils will remain in reservoirs worldwide after conventional recovery methods have been exhausted and much of this volume would be recovered by Enhanced Oil Recovery (EOR) methods. The in-situ combustion (ISC) is an EOR method in which an oxygen-containing gas is injected into a reservoir where it reacts with the crude oil to create a high-temperature combustion front that is propagated through the reservoir. The High Pressure Air Injection (HPAI) method is a particular denomination of the air injection process applied in light oil reservoirs, for which the combustion reactions are dominant between 150 and 300°C and the generation of flue gas is the main factor to the oil displacement. A simulation model of a homogeneous reservoir was built to study, which was initially undergone to primary production, for 3 years, next by a waterflooding process for 21 more years. At this point, with the mature condition established into the reservoir, three variations of this model were selected, according to the recovery factors (RF) reached, for study the in-situ combustion (HPAI) technique. Next to this, a sensitivity analysis on the RF of characteristic operational parameters of the method was carried out: air injection rate per well, oxygen concentration into the injected gas, patterns of air injection and wells perforations configuration. This analysis, for 10 more years of production time, was performed with assistance of the central composite design. The reservoir behavior and the impacts of chemical reactions parameters and of reservoir particularities on the RF were also evaluated. An economic analysis and a study to maximize the RF of the process were also carried out. The simulation runs were performed in the simulator of thermal processes in reservoirs STARS (Steam, Thermal, and Advanced Processes Reservoir Simulator) from CMG (Computer Modelling Group). The results showed the incremental RF were small and the net present value (NPV) is affected by high initial investments to compress the air. It was noticed that the adoption of high oxygen concentration into the injected gas and of the five spot pattern tends to improve the RF, and the wells perforations configuration has more influence with the increase of the oil thickness. Simulated cases relating to the reservoir particularities showed that smaller residual oil saturations to gas lead to greater RF and the presence of heterogeneities results in important variations on the RF and on the production curves

Intravitreal injection versus sub-Tenon's infusion of triamcinolone acetonide for refractory diabetic macular edema: A randomized clinical trial

PURPOSE. To compare the effectiveness of posterior sub-Tenon's infusion (STi) and intravitreal injection (IVI) of triamcinolone acetonide (TA) for treatment of refractory diffuse diabetic macular edema.METHODS. Thirty-six phakic diabetic patients with refractory diffuse diabetic macular edema were prospectively enrolled. Patients randomly received either 40 mg STi or 4 mg IVI of TA. Comprehensive ophthalmic evaluation was performed at baseline and 1, 2, 4, 8 +/- 1, 12 +/- 2 and 24 +/- 2 weeks after treatment. Macular morphologic changes detected by optical coherence tomography and visual acuity, intraocular pressure, and lens status were evaluated.RESULTS. Twenty-eight patients (28 eyes) completed the 24-week study. Central macular thickness was significantly reduced in the IVI group when compared with the STi group at 2, 4, 8, 12, and 24 weeks after treatment (P < 0.01). Mean visual acuities (in logarithm of the minimum angle of resolution [logMAR]) at week-4, -8, and -12 follow-up examinations were significantly higher in the IVI group (0.74, 0.75, and 0.82, respectively) when compared with the STi group (0.88, 0.88, and 0.90, respectively; P < 0.01). A significant change from baseline in mean intraocular pressure (mm Hg) was seen at weeks 4 (+/- 3.21) and 8 (+/- 3.35) in STi the group (P < 0.01), and at week 8 (+/- 2.78) in the IVI group (P < 0.05). No patient had cataract progression during the study.CONCLUSIONS. Although the number of patients and length of follow-up in this preliminary study were limited, the changes in central macular thickness and visual acuity observed after treatment suggest that IVI TA may be more effective than STi for the management of refractory diffuse diabetic macular edema. Further studies are needed to confirm these preliminary findings.

Intra-prostatic injection of botulinum toxin type A in treatment of dogs with spontaneous benign prostatic hyperplasia

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

A Single Intraoperative Sub-Tenon's Capsule Injection of Triamcinolone and Ciprofloxacin in a Controlled-Release System for Cataract Surgery

PURPOSE. To compare intraoperative injection of triamcinolone and ciprofloxacin in a controlled-release system (DuoCat) with prednisolone and ciprofloxacin eye drops after cataract surgery.METHODS. In this randomized, double-masked, controlled trial, a total of 135 patients undergoing cataract surgery were randomly allocated to two groups: 67 patients treated after surgery with prednisolone 1% and ciprofloxacin 3% eye drops four times daily (week 1), three times daily (week 2), twice daily (week 3), and once daily (week 4) and 0.3% ciprofloxacin drops four times daily (weeks 1 and 2), and 68 patients treated at the end of surgery with a sub-Tenon's injection of 25 mg triamcinolone and 2 mg ciprofloxacin in biodegradable microspheres. The patients were examined on postoperative days 1, 3, 7, 14, and 28. The main outcome measures were postoperative anterior chamber cell and flare, intraocular pressure (IOP), lack of anti-inflammatory response, and presence of infection.RESULTS. No significant differences were observed between the groups in anterior chamber cell (P > 0.14) and flare (P > 0.02) at any postoperative visits. The mean (99% confidence interval) differences in IOP between the prednisolone and triamcinolone groups on days 1, 3, 7, 14, and 28 were -0.4 mm Hg (-2.1 to 1.3), 0.0 mm Hg (-1.4 to 1.3), 0.0 mm Hg (-1.1 to 1.1), -0.2 mm Hg (-1.1 to 0.8), and -0.1 mm Hg (-1.1 to 0.9), respectively. No patient had a postoperative infection.CONCLUSIONS. One injection of DuoCat had a therapeutic response and ocular tolerance that were equivalent to conventional eye drops in controlling inflammation after cataract surgery. (Clinical-Trials. gov number, NCT00431028.) (Invest Ophthalmol Vis Sci. 2009; 50: 3041-3047) DOI: 10.1167/iovs.08-2920

Parameterized fast decoupled power flow methods for obtaining the maximum loading point of power systems. Part I. Mathematical modeling

The conventional Newton and fast decoupled power flow (FDPF) methods have been considered inadequate to obtain the maximum loading point of power systems due to ill-conditioning problems at and near this critical point. It is well known that the PV and Q-theta decoupling assumptions of the fast decoupled power flow formulation no longer hold in the vicinity of the critical point. Moreover, the Jacobian matrix of the Newton method becomes singular at this point. However, the maximum loading point can be efficiently computed through parameterization techniques of continuation methods. In this paper it is shown that by using either theta or V as a parameter, the new fast decoupled power flow versions (XB and BX) become adequate for the computation of the maximum loading point only with a few small modifications. The possible use of reactive power injection in a selected PV bus (Q(PV)) as continuation parameter (mu) for the computation of the maximum loading point is also shown. A trivial secant predictor, the modified zero-order polynomial which uses the current solution and a fixed increment in the parameter (V, theta, or mu) as an estimate for the next solution, is used in predictor step. These new versions are compared to each other with the purpose of pointing out their features, as well as the influence of reactive power and transformer tap limits. The results obtained with the new approach for the IEEE test systems (14, 30, 57 and 118 buses) are presented and discussed in the companion paper. The results show that the characteristics of the conventional method are enhanced and the region of convergence around the singular solution is enlarged. In addition, it is shown that parameters can be switched during the tracing process in order to efficiently determine all the PV curve points with few iterations. (C) 2003 Elsevier B.V. All rights reserved.

Parameterized fast decoupled power flow methods for obtaining the maximum loading point of power systems. Part II. Performance evaluation

The parameterized fast decoupled power flow (PFDPF), versions XB and BX, using either theta or V as a parameter have been proposed by the authors in Part I of this paper. The use of reactive power injection of a selected PVbus (Q(PV)) as the continuation parameter for the computation of the maximum loading point (MLP) was also investigated. In this paper, the proposed versions obtained only with small modifications of the conventional one are used for the computation of the MLP of IEEE test systems (14, 30, 57 and 118 buses). These new versions are compared to each other with the purpose of pointing out their features, as well as the influence of reactive power and transformer tap limits. The results obtained with the new approaches are presented and discussed. The results show that the characteristics of the conventional FDPF method are enhanced and the region of convergence around the singular solution is enlarged. In addition, it is shown that these versions can be switched during the tracing process in order to efficiently determine all the PV curve points with few iterations. A trivial secant predictor, the modified zero-order polynomial, which uses the current solution and a fixed increment in the parameter (V, theta, or mu) as an estimate for the next solution, is used for the predictor step. (C) 2003 Elsevier B.V. All rights reserved.

Efeitos de concentrações crescentes de lidocaína hiperbárica, administradas no espaço subaracnóideo, sobre a medula espinhal e as meninges: estudo experimental em cães

JUSTIFICATIVA E OBJETIVOS: Ainda não está bem estabelecida a concentração de lidocaína que é potencialmente capaz de determinar lesão no tecido nervoso. O objetivo desta pesquisa foi estudar os efeitos sobre a medula espinhal e as meninges, de concentrações crescentes de lidocaína administrada por via subaracnóidea, em injeção única através de agulha de Quincke. MÉTODO: Após a aprovação da Comissão de Ética em Experimentação Animal, 40 cães adultos foram anestesiados com fentanil e etomidato e submetidos a punção subaracnóidea com agulha de Quincke 22G 21/2 para introdução de 1 mL, em 10 segundos, de solução glicosada a 7,5% - Grupo 1; lidocaína a 5% em solução glicosada a 7,5% - Grupo 2; lidocaína a 7,5% em solução glicosada a 7,5% - Grupo 3; lidocaína a 10% em solução glicosada a 7,5% - Grupo 4. Após a recuperação da anestesia venosa, foram observados, no período em que os animais estavam em vigência do bloqueio subaracnóideo, a presença de bloqueio motor, o tônus do esfíncter anal (normal ou relaxado) e o nível de bloqueio sensitivo nos diferentes dermátomos das regiões cervical, torácica, lombar e sacral. Os animais permaneceram em cativeiro por 72 horas. Foram avaliados o tônus do esfíncter anal, a motricidade das patas posteriores, a sensibilidade dolorosa nas patas anteriores e posteriores e nos dermátomos sacrais, lombares e torácicos. Após serem sacrificados por eletrocussão sob anestesia, foram retiradas porções lombar e sacral da medula espinhal e das meninges para exame histológico por microscopia óptica. RESULTADOS: Nenhum animal dos Grupos 1 e 2 apresentou lesões clínicas ou histológicas. Três animais do Grupo 3 apresentaram alterações motoras nas patas posteriores e relaxamento do esfíncter anal. Nestes, foram observados focos de necrose na região posterior (dois cães) e necrose em faixa em toda a superfície medular (um cão). em um outro animal deste grupo, no qual foram notados focos de necrose, em área inferior a 5% do campo histológico não foram encontradas alterações clínicas. Sete animais do Grupo 4 apresentaram alterações clínicas (paralisia ou diminuição de força muscular nas patas posteriores, relaxamento do esfíncter anal) e histológicas (necrose na faixa da superfície medular ou focos de necrose de tecido nervoso). CONCLUSÕES: Neste estudo, a lidocaína em concentrações superiores a 7,5%, em injeção única, administrada no espaço subaracnóideo por meio de agulha de Quincke, determinou alterações histológicas sobre a medula espinhal, mas não sobre as meninges.

Estudo comparativo do bloqueio combinado femoral-isquiático, por punção em sítio único, com anestesia subaracnóidea para cirurgia unilateral do membro inferior

JUSTIFICATIVA E OBJETIVOS: A raquianestesia unilateral pode apresentar vantagens em pacientes ambulatoriais. O objetivo deste trabalho foi comparar a raquianestesia unilateral com o bloqueio combinado femoral-isquiático em cirurgias ortopédicas unilaterais e ambulatoriais. MÉTODO: Sessenta pacientes foram aleatoriamente separados em dois grupos para receber 6 mg de bupivacaína hiperbárica ou hipobárica (grupo RQ) em decúbito lateral esquerdo ou 800 mg de lidocaína 1,6% com epinefrina nos nervos femoral e isquiático (grupo CFI) em decúbito dorsal. O bloqueio dos nervos foi realizado com agulha de 150 mm conectada a um neuroestimulador e inserida no ponto médio entre as duas abordagens clássicas, sendo injetados 15 mL no nervo femoral e 35 mL no nervo isquiático. Avaliados o tempo para realização dos bloqueios e sua duração. Vinte minutos após, os pacientes foram avaliados em relação aos bloqueios sensitivo e motor. RESULTADOS: O tempo para a realização da raquianestesia foi significativamente menor do que o bloqueio combinado femoral-isquiático. O bloqueio unilateral foi obtido em 90% dos pacientes no grupo RQ e 100% no grupo CFI. O tempo para recuperação do bloqueio sensitivo e motor foi significativamente maior no grupo CFI. Não houve bradicardia ou hipotensão. CONCLUSÕES: Este estudo conclui que é tecnicamente fácil realizar bloqueio anterior combinado femoral-isquiático e pode ser uma alternativa para o bloqueio unilateral do membro inferior. A raquianestesia unilateral com baixas doses de bupivacaína resultou em menor tempo para realização, menor número de tentativas e recuperação mais precoce do bloqueio combinado femoral-isquiático, porém com mesma efetividade.

Administration of beta(2)-adrenergic agonists during the peri-implantation period does not improve implantation or pregnancy rates in intracytoplasmic sperm injection (ICSI) cycles

Purpose: the objective of the present investigation was to determine implantation and pregnancy rates in patients undergoing ICSI and treated with beta(2)-adrenergic agonists, considering the uterine-relaxing action of these agents.Methods: A total of 225 women undergoing ICSI at the Center for Human Reproduction, Sinha Junqueira Maternity Foundation, entered the study. Patient participation in each group was random, by drawing lots, using a randomization table previously elaborated for the study (2:2:1). The group I (90 women) received 10 mg of terbutaline daily for 15 days starting on the day of oocyte retrieval; group II (90 women) received 20 mg of ritodrine daily during the same period of time as group I; group III (45 patients) received no treatment and was used as control. The evaluation was interrupted in 3 patients of group I and in 30 patients of group II because of a high incidence of side effects.Results: Pregnancy, implantation, and miscarriage rates were not significantly different (p>0.05) between the three groups: 29.88%, 13.25%, and 26.9% for group I; 33.33%, 17.5%, and 10.0% for group II; 28.88%, 15.07%, and 15.38% for group III, respectively.Conclusions: the results of this study do not support the routine use of beta(2)-adrenergic agonists during the peri-implantation period in assisted reproductive technology cycles.

Evaluation of N-acetilglucosaminidase and myeloperoxidase activity in patients with endometriosis-related infertility undergoing intracytoplasmic sperm injection

Aim: Inflammation is as an important factor in ovulation with the active participation of leucocytes and their inflammatory mediators. The present study was performed to compare the activity of the inflammatory enzymes myeloperoxidase (MPO) and N-acetylglucosaminidase (NAG) in patients with endometriosis-related infertility and in normally ovulating women undergoing intracytoplasmic sperm injection (ICSI).Material and Methods: This prospective study included infertile women undergoing ICSI treatment. These women were divided into two groups: endometriosis anovulation (n = 18) and normally ovulating (n = 20). NAG and MPO activity was evaluated colorimetrically in serum and in follicular fluids obtained at the time of oocyte retrieval.Results: There was a significant correlation between the serum and follicular fluid activities of NAG and MPO (tau = 0.256, P = 0.025; and tau = -0.234, P = 0.041; respectively). Both serum and follicular fluid NAG activities were higher in patients with endometriosis compared to the control group (P < 0.001). MPO follicular fluid activity was lower in patients with endometriosis compared to normally ovulating women (P = 0.016).Conclusion: Infertile patients with endometriosis show a distinct pattern of serum and follicular fluid macrophage/neutrophil activation compared to normally ovulating women undergoing ICSI, which may reflect the role of immune and inflammatory alterations in endometriosis-related infertility.

Sperm Organelle Morphologic Abnormalities: Contributing Factors and Effects on Intracytoplasmic Sperm Injection Cycles Outcomes

OBJECTIVE To (1) analyze possible relationships between motile sperm organelle morphology examination (MSOME) and sperm chromatin status, aneuploidy incidence, and patient's age; (2) determine the effects of sperm morphologic abnormalities on intracytoplasmic sperm injection (ICSI) outcomes; and (3) identify the benefits of intracytoplasmic morphologically selected sperm injection (IMSI) in patients with high DNA fragmentation rate.METHODS The study was performed in 50 patients undergoing ICSI cycles. The MSOME, sperm DNA fragmentation, and sperm aneuploidy incidence were performed in 200 sperm cells of each patient. Regression models were used to assess the relationships among sperm morphology and sperm aneuploidy, sperm DNA fragmentation, patient's age, and ICSI outcomes. In cycles with patients showing a high incidence of DNA fragmentation, oocytes were split into 2 groups according to the sperm selection method: Standard-ICSI (n = 82) and IMSI (n = 79). Fertilization and high-quality embryo rates were compared between the groups.RESULTS A close relationship between sperm DNA fragmentation and the presence of vacuoles in the MSOME was noted. The patient's age was correlated to the presence of vacuoles. No correlation between sperm aneuploidy and IMSI was observed. Vacuolated cells were negatively correlated with fertilization, pregnancy, and implantation. In patients with a high incidence of sperm DNA fragmentation, fertilization and high-quality embryo rates were similar when comparing IMSI and Standard-ICSI.CONCLUSIONS Our data demonstrate a correlation between paternal age and the incidence of nuclear vacuoles, as well as an effect of large and small vacuoles on late embryo development. UROLOGY 78: 786-791, 2011. (C) 2011 Elsevier B.V.

Single-embryo transfer reduces clinical pregnancy rates and live births in fresh IVF and Intracytoplasmic Sperm Injection (ICSI) cycles: a meta-analysis

Background: It has become an accepted procedure to transfer more than one embryo to the patient to achieve acceptable ongoing pregnancy rates. However, transfers of more than a single embryo increase the probability of establishing a multiple gestation. Single-embryo transfer can minimize twin pregnancies but may also lower live birth rates. This meta-analysis aimed to compare current data on single-embryo versus double-embryo transfer in fresh IVF/ICSI cycles with respect to implantation, ongoing pregnancy and live birth rates.Methods: Search strategies included on-line surveys of databases from 1995 to 2008. Data management and analysis were conducted using the Stats Direct statistical software. The fixed-effect model was used for odds ratio (OR). Fixed-effect effectiveness was evaluated by the Mantel Haenszel method. Seven trials fulfilled the inclusion criteria.Results: When pooling results under the fixed-effect model, the implantation rate was not significantly different between double-embryo transfer (34.5%) and single-embryo transfer group (34.7%) (P = 0.96; OR = 0.99, 95% CI 0.78, 1.25). on the other hand, double-embryo transfer produced a statistically significantly higher ongoing clinical pregnancy rate (44.5%) than single-embryo transfer (28.3%) (P < 0.0001; OR: 2.06, 95% CI = 1.64,2.60). At the same time, pooling results presented a significantly higher live birth rate when double-embryo transfer (42.5%) (P < 0.001; OR: 1.87, 95% CI = 1.44,2.42) was compared with single-embryo transfer (28.4%).Conclusion: Meta-analysis with 95% confidence showed that, despite similar implantation rates, fresh double-embryo transfer had a 1.64 to 2.60 times greater ongoing pregnancy rate and 1.44 to 2.42 times greater live birth rate than single-embryo transfer in a population suitable for ART treatment.