Increasing ionic conductivity and mechanical strength of a plastic electrolyte by inclusion of a polymer

in this contribution we present a soft matter solid electrolyte which was obtained by inclusion of a polymer (polyacrylonitrile, PAN) in LiClO4/LiTFSI-succinonitrile (SN), a semi-solid organic plastic electrolyte. Addition of the polymer resulted in considerable enhancement in ionic conductivity as well as mechanical strength of LiX-SN (X=ClO4, TFSI) plastic electrolyte. Ionic conductivity of 92.5%-[1 M LiClO4-SN]:7.5%-PAN (PAN amount as per SN weight) composite at 25 degrees C recorded a remarkably high value of 7 x 10(-3) Omega(-1) cm(-1), higher by few tens of order in magnitude compared to 1 M LiClO4-SN. Composite conductivity at sub-ambient temperature is also quite high. At -20 degrees C, the ionic conductivity of (100 -x)%-[1 M LiClO4-SN]:x%-PAN composites are in the range 3 x 10(-5)-4.5 x 10(-4) Omega(-1) cm(-1), approximately one to two orders of magnitude higher with respect to 1 M LiClO4-SN electrolyte conductivity. Addition of PAN resulted in an increase of the Young's modulus (Y) from Y -> 0 for LiClO4-SN to a maximum of 0.4MPa for the composites. Microstructural studies based on X-ray diffraction, differential scanning calorimetry and Fourier transform infrared spectroscopy suggest that enhancement in composite ionic conductivity is a combined effect of decrease in crystallinity and enhanced trans conformer concentration. (c) 2008 Elsevier Ltd. All rights reserved.

The physics of ENSO-monsoon connection

The physical mechanism through which Ei-Nino and Southern Oscillation (ENSO) tends to produce deficient precipitation over Indian continent is investigated using both observations as well as a general circulation model. Both analysis of observations and atmospheric general circulation model (AGCM) study show that the planetary scale response associated with ENSO primarily influences the equatorial Indian Ocean region. Through this interaction it tends to favour the equatorial heat source, enhance precipitation over the equatorial Indian Ocean and indirectly cause a decrease in continental precipitation through induced subsidence. This situation is further complicated by the fact the regional tropospheric quasi biennial oscillation (QBO) has a bimodal structure over this region with large amplitude over the Indian continent. While the ENSO response has a quasi-four year periodicity and tends peak during beginning of the calendar year, the QBO mode tends to peak during northern summer. Thus, the QBO mode exerts a stronger influence on the interannual variability of the monsoon. The strength of the Indian monsoon in a given year depends on the combined effect of the ENSO and the QBO mode. Sines the two oscillations have disparate time scales, exact phase information of the two modes during northern summer is important in determining the Indian summer monsoon. The physical mechanism of the interannual variations of the Indian monsoon precipitation associated with ENSO presented here is similar to the physical process that cause intraseasonal 'active', 'break' oscillations of the monsoon.

SIR Analysis and Interference Cancellation in Uplink OFDMA with Large Carrier Frequency/Timing Offsets

In uplink orthogonal frequency division multiple access (OFDMA), large timing offsets (TO) and/or carrier frequency offsets (CFO) of other users with respect to a desired user can cause significant multiuser interference (MUI). In this letter, we analytically characterize the degradation in the average output signal-to-interference ratio (SIR) due to the combined effect of both TOs as well as CFOs in uplink OFDMA. Specifically, we derive closed-form expressions for the average SIR at the DFT output in the presence of large CFOs and TOs. The analyticalexpressions derived for the signal and various interference terms at the DFT output are used to devise an interference cancelling receiver to mitigate the effect of CFO/TO-induced interferences.

Thermoelectric Properties of Co4Sb12 Skutterudite Materials with Partial In Filling and Excess In Additions

The properties of Co4Sb12 with various In additions were studied. X-ray diffraction revealed the presence of the pure δ-phase of In0.16Co4Sb12, whereas impurity phases (γ-CoSb2 and InSb) appeared for x = 0.25, 0.40, 0.80, and 1.20. The homogeneity and morphology of the samples were observed by Seebeck microprobe and scanning electron microscopy, respectively. All the quenched ingots from which the studied samples were cut were inhomogeneous in the axial direction. The temperature dependence of the Seebeck coefficient (S), electrical conductivity (σ), and thermal conductivity (κ) was measured from room temperature up to 673 K. The Seebeck coefficient of all In-added Co4Sb12 materials was negative. When the filler concentration increases, the Seebeck coefficient decreases. The samples with In additions above the filling limit (x = 0.22) show an even lower Seebeck coefficient due to the formation of secondary phases: InSb and CoSb2. The temperature variation of the electrical conductivity is semiconductor-like. The thermal conductivity of all the samples decreases with temperature. The central region of the In0.4Co4Sb12 ingot shows the lowest thermal conductivity, probably due to the combined effect of (a) rattling due to maximum filling and (b) the presence of a small amount of fine-dispersed secondary phases at the grain boundaries. Thus, regardless of the non-single-phase morphology, a promising ZT (S 2 σT/κ) value of 0.96 at 673 K has been obtained with an In addition above the filling limit.

Kohti hyvää suometsien hoitoa : harvennusten ja kunnostusojitusten vaikutus ojitusaluemänniköiden puuntuotokseen ja metsänkasvatuksen taloustulokseen

This thesis examines the impacts of silvicultural activities on productivity and financial returns of Scots pine (Pinus sylvestris L.) stands on drained peatlands in Finland. The effects of ditch network maintenance operations (DNM) and thinnings, with different timings and intensities, were studied. Based on stand development simulations, the best regimes for different types of stands according to site type, climatic area, and stand silvicultural status were defined from the viewpoint of both wood production and financial profitability. Certain aspects affecting the management outcomes, such as the timing of the first thinning, were examined using data from thinning experiments. Long-term predictions of the impacts of different management regimes were carried out by simulating the development of well-representative model-stands which were composed from appropriate inventory data sets. The MOTTI stand simulator used to perform the simulations enables the predictions by utilizing specific models for drained peatland stands. In addition to natural stand dynamics, these models describe the effects of silvicultural treatments on the development of a given stand. The mean annual increment of merchantable wood (MAImerch) was used as the measure of wood productivity, and the financial feasibility of the regimes was compared using net present value (NPV) analysis. Silvicultural treatments, when applied to appropriately match stand condition, increased both the productivity and financial returns of stand management. Applying DNM resulted in a small increase in MAImerch. When thinning was introduced along with DNM, their combined effect on wood productivity was considerable. According to current operational practices, DNM is generally combined with thinning. In some cases, e.g., in sites of low productivity, the need for DNM may become apparent prior to the thinning stage. As for profitability, thinnings proved to be crucial. The regimes with heavy and late thinnings were generally more profitable than those with normal thinnings. Further, early thinning (relative to stand volume) lacked appeal when seeking a financially profitable removal from the first thinning. In young stands with an initially poor silvicultural condition, however, applying even a low-yielding first thinning considerably increased the NPV when compared to a regime with no thinning at all. Generally, the regimes resulting in the best profitability included heavier thinnings and fewer DNM and thinning treatments than did the regimes resulting in the best yield results. This study demonstrates considerable potential for profitable wood production-oriented management in pine stands on drained peatlands despite their challenging circumstances and long rotations. The results can be used for defining new and more site-specific silvicultural guidelines for various types of drained, pine-dominated peatland stands within the entire range of boreal conditions.

The effects of environmental factors on biomass and microcystin production by the freshwater cyanobacterial genera Microcystis and Anabaena

Several cyanobacterial genera produce the hepatotoxins, microcystins. Microcystins are produced only in cells that have microcystin synthetase gene (mcy) clusters, which encode enzyme complexes involved in microcystin biosynthesis. Microcystin-producing and nonmicrocystin-producing genotypes of single cyanobacterial genus may occur simultaneously in situ. Previously, the effects of environmental factors on the growth and microcystin production of cyanobacteria have mainly been studied by means of isolated cyanobacteria cultures in the laboratory. Studies in the field have been difficult, owing to the lack of methods to identify and quantify the different genotypes. In this study, genus-specific microcystin synthetase E (mcyE) gene primers were designed and a method to identify and quantify the mcyE copy numbers was developed and used in situ. Microcystis and Anabaena mcyE genes were observed in two Finnish lakes. Microcystis appeared to be the most abundant microcystin producer in Lake Tuusulanjärvi and in one basin of Lake Hiidenvesi. Because the most potent microcystin-producing genus of a lake can be identified, it will be possible in the future to design genus-targeted strategies for lake restoration. Effects of P and N concentrations on the biomass of microcystin-producing and nonmicrocystin-producing Microcystis strains and an Anabaena strain were studied in cultures. P and N concentrations and their combined effect increased cyanobacterial biomass of all Microcystis strains. The biomass of microcystin-producing Microcystis was higher than that of nonmicrocystin-producing strains at high nutrient concentrations. The P concentration increased Anabaena biomass, but the effect of N concentration was statistically insignificant for growth yield, probably due to the ability of the genus to fix molecular N2. P and N concentrations and combined nutrients caused an increase in cellular microcystin concentrations of the Microcystis strain cultivated in chemostat cultures. Cyanobacteria are able to hydrolyse nutrients from organic matter through extracellular enzyme activities. Leucine aminopeptidase (LAP) activity was observed in an axenic N2-fixing Anabaena strain grown in batch cultures. The P concentration caused a statistically significant increase in LAP activity, whereas the effect of N concentration was insignificant. The highest LAP activities were observed in the most eutrophic basins of Lake Hiidenvesi. LAP activity probably originated mostly from attached heterotrophic bacteria and less from cyanobacteria.

The structure of 3-(2-methoxyphenyl)-1,1,2,2-cyclopropanetetracarbonitrile

Crystals of C I4HsN40 are monoclinic, space group P21, Unit-cell constants are a = 13.241(4), b = 7.446 (2), c = 6.436 (2)/A, B= 93.23 (2) °. V= 633.5 /A3, Z = 2, Dob s = 1.30 (flotation), Dealt = 1.300 Mg m -3 and #(Cu Ka) = 0.72 mm -1. The structure, solved by direct methods, has been refined to an R value of 3.5% using 1245 intensity measurements. The combined effect of electron-withdrawing and –donating substituents on the geometry of the cyclopropane ring is discussed.

Variability in exposure to ambient ultrafine particles in urban schools: Comparative assessment between Australia and Spain

Ambient ultrafine particle number concentrations (PNC) have inhomogeneous spatio-temporal distributions and depend on a number of different urban factors, including background conditions and distant sources. This paper quantitatively compares exposure to ambient ultrafine particles at urban schools in two cities in developed countries, with high insolation climatic conditions, namely Brisbane (Australia) and Barcelona (Spain). The analysis used comprehensive indoor and outdoor air quality measurements at 25 schools in Brisbane and 39 schools in Barcelona. PNC modes were analysed with respect to ambient temperature, land use and urban characteristics, combined with the measured elemental carbon concentrations, NOx (Brisbane) and NO2 (Barcelona). The trends and modes of the quantified weekday average daily cycles of ambient PNC exhibited significant differences between the two cities. PNC increases were observed during traffic rush hours in both cases. However, the mid-day peak was dominant in Brisbane schools and had the highest contribution to total PNC for both indoors and outdoors. In Barcelona, the contribution from traffic was highest for ambient PNC, while the mid-day peak had a slightly higher contribution for indoor concentrations. Analysis of the relationships between PNC and land use characteristics in Barcelona schools showed a moderate correlation with the percentage of road network area and an anti-correlation with the percentage of green area. No statistically significant correlations were found for Brisbane. Overall, despite many similarities between the two cities, school-based exposure patterns were different. The main source of ambient PNC at schools was shown to be traffic in Barcelona and mid-day new particle formation in Brisbane. The mid-day PNC peak in Brisbane could have been driven by the combined effect of background and meteorological conditions, as well as other local/distant sources. The results have implications for urban development, especially in terms of air quality mitigation and management at schools.

Inelastic Postbuckling of Columns of Variable Flexural Rigidity

Effects of large deformation and inelasticity are considered in formulating the behavior of columns of variable cross section subjected to an axial compressive load. Simple, approximate methods are used to obtain numerical results. The combined effect of the nonlinearities is shown to be of a hardening type for small column deflections

Theoretical calculations of base-base interactions in nucleic acids: I Stacking interactions in free bases

Stacking interactions in free bases were computed on the basis of molecular association. The results of the calculations were compared with the stacking patterns observed in a few single crystals of nucleic acid components as examples. The following are the conclusions: (i) there can be two types of stacking pattern classified as normal and inverted types for any two interacting bases and both can be energetically favourable (ii) in both the types the stacking interaction is a combined effect of the overlap of the interacting bases and relative positions and orientations of the atomic centres of the two bases (iii) crystal symmetry and H-bonding interaction may influence stacking patterns.

Modeling of Freezing Phenomena Induced by Chemical Reactions

Spatial variations in the concentration of a reactive solute in solution are often encountered in a catalyst particle, and this leads to variation in the freezing point of the solution. Depending on the operating temperature, this can result in freezing of the solvent oil a portion of catalyst, rendering that part of the active area ineffective Freezing call occur by formation of a sharp front or it mush that separates the solid and fluid phases. In this paper, we model the extent of reduction in the active area due to freezing. Assuming that the freezing point decreases linearly with solute concentration, conditions for freezing to occur have been derived. At steady state, the ineffective fraction of catalyst pellet is found to be the same irrespective of the mode of freezing. Progress of freezing is determined by both the heat of reaction and the latent heat of fusion Unlike in freezing of alloys where the latter plays a dominant role, the exothermicity of the reaction has a significant effect on freezing in the presence of chemical reactions. A dimensionless group analogous to the Stefan number could be defined to capture the combined effect of both of these.

Cyclins in Breast Cancer

Breast cancer is the most common malignancy in women in Western countries. It is a heterogeneous disease with varying biological characteristics and aggressiveness. Family history is one of the strongest predisposing factors for breast cancer. The known susceptibility genes explain only around 25% of all familial breast cancers. At least part of the unknown familial aggregation may be caused by several low-penetrance variants that occur commonly in the general population. Cyclins are cell cycle-regulating proteins. Cyclin expression oscillates during the cell cycle and is under strict control. In cancer cells, cyclin expression often becomes deregulated, leading to uncontrolled cell division and proliferation, one of the hallmarks of cancer. In this study, we investigated the role of cyclins in breast cancer predisposition, pathogenesis, and tumor behavior. Cyclin A immunohistochemistry was evaluated both on traditional large sections and on tissue microarrays (TMA). The concordance of the results was good, indicating that TMA is a reliable method for studying cyclin expression in breast cancer. The expression of cyclins D1, E, and B1 was studied among 1348 invasive breast cancers on TMA. Familial BRCA1/2-mutation negative tumors had significantly more often low cyclin E and high cyclin D1 expression than BRCA1/2 related or sporadic tumors. Unique cyclin E and D1 expression patterns among familial non-BRCA1/2 breast cancers may reflect different predisposition and pathogenesis in these groups and help to differentiate mutation-positive from mutation-negative familial cancers. High cyclin E expression was associated with an aggressive breast cancer phenotype and was an independent marker of poor metastasis-free survival. High cyclin D1 was associated with high grade and high proliferation among estrogen receptor (ER)-positive but with low grade and low proliferation among ER-negative breast cancers. Among ER-positive cancers not treated with chemotherapy, high cyclin D1 showed a trend towards shorter metastasis-free survival. These results suggest that different mechanisms may drive proliferation in ER-negative and -positive breast cancers and that cyclin D1 has a particularly important role in tumorigenesis of hormone receptor-positive breast cancer. High cyclin B1 expression was associated with aggressive breast cancer features and had an independent impact on survival. The results suggest that cyclin B1 immunohistochemistry is a method that could easily be adapted for routine use and is an independent prognostic factor, adding specificity to prognostic evaluation conducted with traditional markers. A commonly occurring cyclin D1 gene polymorphism A870G was associated with increased breast cancer risk in a large material of Finnish and Canadian breast cancer patients. The interaction of the high-activity alleles of cyclin D1 gene and estrogen metabolism gene COMT conferred an even higher risk. These results show that cyclin D1 and COMT act synergistically to contribute to breast cancer progression and that individual risk for breast cancer can be altered by the combined effect of polymorphisms with low-penetrance alleles. By investigating critical cell cycle regulator protein cyclins, we revealed new aspects of breast cancer predisposition, pathogenesis, and clinical course.

Detection of multicode STBC signals in frequency selective fading

Multicode operation in space-time block coded (STBC) multiple input multiple output (MIMO) systems can provide additional degrees of freedom in code domain to achieve high data rates. In such multicode STBC systems, the receiver experiences code domain interference (CDI) in frequency selective fading. In this paper, we propose a linear parallel interference cancellation (LPIC) approach to cancel the CDI in multicode STBC in frequency selective fading. The proposed detector first performs LPIC followed by STBC decoding. We evaluate the bit error performance of the detector and show that it effectively cancels the CDI and achieves improved error performance. Our results further illustrate how the combined effect of interference cancellation, transmit diversity, and RAKE diversity affect the bit error performance of the system.

Accuracy of absorbed dose in external photon beam radiotherapy : what level is sufficient and how to approach it?

Radiation therapy (RT) plays currently significant role in curative treatments of several cancers. External beam RT is carried out mostly by using megavoltage beams of linear accelerators. Tumor eradication and normal tissue complications correlate to dose absorbed in tissues. Normally this dependence is steep and it is crucial that actual dose within patient accurately correspond to the planned dose. All factors in a RT procedure contain uncertainties requiring strict quality assurance. From hospital physicist´s point of a view, technical quality control (QC), dose calculations and methods for verification of correct treatment location are the most important subjects. Most important factor in technical QC is the verification that radiation production of an accelerator, called output, is within narrow acceptable limits. The output measurements are carried out according to a locally chosen dosimetric QC program defining measurement time interval and action levels. Dose calculation algorithms need to be configured for the accelerators by using measured beam data. The uncertainty of such data sets limits for best achievable calculation accuracy. All these dosimetric measurements require good experience, are workful, take up resources needed for treatments and are prone to several random and systematic sources of errors. Appropriate verification of treatment location is more important in intensity modulated radiation therapy (IMRT) than in conventional RT. This is due to steep dose gradients produced within or close to healthy tissues locating only a few millimetres from the targeted volume. The thesis was concentrated in investigation of the quality of dosimetric measurements, the efficacy of dosimetric QC programs, the verification of measured beam data and the effect of positional errors on the dose received by the major salivary glands in head and neck IMRT. A method was developed for the estimation of the effect of the use of different dosimetric QC programs on the overall uncertainty of dose. Data were provided to facilitate the choice of a sufficient QC program. The method takes into account local output stability and reproducibility of the dosimetric QC measurements. A method based on the model fitting of the results of the QC measurements was proposed for the estimation of both of these factors. The reduction of random measurement errors and optimization of QC procedure were also investigated. A method and suggestions were presented for these purposes. The accuracy of beam data was evaluated in Finnish RT centres. Sufficient accuracy level was estimated for the beam data. A method based on the use of reference beam data was developed for the QC of beam data. Dosimetric and geometric accuracy requirements were evaluated for head and neck IMRT when function of the major salivary glands is intended to be spared. These criteria are based on the dose response obtained for the glands. Random measurement errors could be reduced enabling lowering of action levels and prolongation of measurement time interval from 1 month to even 6 months simultaneously maintaining dose accuracy. The combined effect of the proposed methods, suggestions and criteria was found to facilitate the avoidance of maximal dose errors of up to even about 8 %. In addition, their use may make the strictest recommended overall dose accuracy level of 3 % (1SD) achievable.

SIR Analysis and Interference Cancellation in Uplink OFDMA with Large Carrier Frequency/Timing Offsets

In uplink OFDMA, carrier frequency offsets (CFO) and/or timing offsets (TO) of other users with respect to a desired user can cause multiuser interference (MUI). In practical uplink OFDMA systems (e.g., IEEE 802.16e standard), effect of this MUI is made acceptably small by requiring that frequency/timing alignment be achieved at the receiver with high precision (e.g., CFO must be within 1 % of the subcarrier spacing and TO must be within 1/8th of the cyclic prefix duration in IEEE 802.16e), which is realized using complex closed-loop frequency/timing correction between the transmitter and the receiver. An alternate open-loop approach to handle the MUI induced by large CFOs and TOs is to employ interference cancellation techniques at the receiver. In this paper, we first analytically characterize the degradation in the average output signal-to-interference ratio (SIR) due to the combined effect of large CFOs and TOs in uplink OFDMA. We then propose a parallel interference canceller (PIC) for the mitigation of interference due to CFOs and TOs in this system. We show that the proposed PIC effectively mitigates the performance loss due to CFO/TO induced interference in uplink OFDMA.