Síntese, caracterização e aplicação de MCM-41 funcionalizado com diisopropilamina no processo de adsorção do dióxido de carbono

Emissions of CO2 in the atmosphere have increased successively by various mechanisms caused by human action, especially as fossil fuel combustion and industrial chemical processes. This leads to the increase in average temperature in the atmosphere, which we call global warming. The search for new technologies to minimize environmental impacts arising from this phenomenon has been investigated. The capture of CO2 is one of the alternatives that can help reduce emis ions of greenhouse gases. The CO2 can be captured through the process of selective adsorption using adsorbents for this purpose. Were synthesized by hydrothermal method, materials of the type MCM-41 and Al-MCM-41 in the molar ratio Si / Al equal to 50. The synthesis of gels were prepared from a source of silicon, sodium, water and aluminum in the case of Al-MCM-41. The period of synthesis of the materials was 5 days in autoclave at 100°C. After that time materials were filtered, washed and dried in greenhouse at 100 º C for 4 hours and then calcined at 450 º C. Then the calcined material was functionalized with the Di-isopropylamine (DIPA) by the method of wet impregnation. We used 0.5 g of material mesopores to 3.5 mL of DIPA. The materials were functionalized in a closed container for 24 hours, and after this period were dried at brackground temperature for 2 hours. Were subsequently subjected to heat treatment at 250°C for 1 hour. These materials were used for the adsorption of CO2 and were characterized by XRD, FT-IR, BET / BJH, SEM, EDX and TG / DTG. Tests of adsorption of CO2 was carried out under the following conditions: 100 mg of adsorbent, temperature of 75°C under flow of 100 mL/min of CO2 for 2 hours. The desorption of CO2 was carried out by thermogravimetry from ambient temperature to 900ºC under flow of 25 mL min of He and a ratio of 10ºC/min. The difratogramas X-ray for the synthesized samples showed the characteristic peaks of MCM-41, showing that the structure of it was obtained. For samples functionalized there was a decrease of the intensities of these peaks, with a consequent reduction in the structural ordering of the material. However, the structure was preserved mesopores. The adsorption tests showed that the functionalized MCM-41 is presented as a material promising adsorbent, for CO2 capture, with a loss of mass on the desorption CO2 of 7,52%, while that in Al-MCM- 41 functionalized showed no such loss

Síntese, caracterização e estudo fotofísico de complexos de 4,4- diaminoestilbeno-2,2-dissulfonato com íons lantanídeos

This is a work involving fundamental studies of chemistry where the synthesis and structural characterization, as well as a possible future application of these new compounds as luminescent sensors or sunscreen agents, complexes with 4,4 diaminostilbene-2,2-disulfonic (DSD) and trivalent lanthanide ions La3+, Nd3+, Eu3+, Gd3+ and Yb3+, were synthesized in the ratio of 3 mmol: 1 mmol (DSD: lanthanides). The complexes obtained with these ions were present in powder form and were characterized by complexometric titration with EDTA CHN Elemental analysis, molecular absorption spectroscopy in the ultraviolet region, the absorption spectroscopy in the infrared, thermal analysis (TG / DTG), Nuclear Magnetic Resonance - NMR 1H and Luminescence Spectroscopy. The complexometric titration and CHN analysis, confirmed the TG / DTG which suggest that these complexes have the following general chemical formulas: [La2(C14H12S2O6N2)2(H2O)2Cl2].7H2O,[Nd2(C14H12S2O6N2)2(H2O)2Cl2].6H2O,[Eu2(C14 H12S2O6N2)2(H2O)2Cl2].7H2O,[Gd2(C14H12S2O6N2)2(H2O)2Cl2].4H2O e [Yb2(C14H12S2O6N2)2(H2O)2].6H2O. The disappearance of the bands in the infrared spectrum at 2921 cm-1 and 2623 cm-1 and the displacement of the bands in the spectra of the amine complex indicate that the lanthanide ion is coordinated to the oxygen atoms and the sulfonate groups of the nitrogens amines, suggesting the formation of the dimer. The disappearance of the signal and the displacement signal SO3H amines in the 1H NMR spectrum of this complex are also indicative coordination and dimer formation. The Thermogravimetry indicates that the DSD is thermally stable in the range of 40º to 385°C and their complexes with lanthanide ions exhibit weight loss between 4 and 5 stages. The Uv-visible spectra indicated that the DSD and complexes exhibit cis isomers. The analysis of luminescence indicates that the complexes do not exhibit emission in the region of the lanthanides but an intense emission part of the binder. This is related to the triplet states of the ligand, which are in the lowest energy state emitting lanthanide ions, and also the formation of the dimer that suppress the luminescence of ion Eu3+. The formation of dimer was also confirmed by calculating the europium complex structure using the model Hamiltonian PM6 and Sparkle

Estudo de materiais mesoporosos funcionalizados com diferentes aminas para captura do dióxido de carbono através do processo de adsorção

Intensive use of machinery and engines burning fuel dumps into the atmosphere huge amounts of carbon dioxide (CO2), causing the intensification of the greenhouse effect. Climate changes that are occurring in the world are directly related to emissions of greenhouse gases, mainly CO2, gases, mainly due to the excessive use of fossil fuels. The search for new technologies to minimize the environmental impacts of this phenomenon has been investigated. Sequestration of CO2 is one of the alternatives that can help minimize greenhouse gas emissions. The CO2 can be captured by the post-combustion technology, by adsorption using adsorbents selective for this purpose. With this objective, were synthesized by hydrothermal method at 100 °C, the type mesoporous materials MCM - 41 and SBA-15. After the synthesis, the materials were submitted to a calcination step and subsequently functionalized with different amines (APTES, MEA, DEA and PEI) through reflux method. The samples functionalized with amines were tested for adsorption of CO2 in order to evaluate their adsorption capacities as well, were subjected to various analyzes of characterization in order to assess the efficiency of the method used for functionalization with amines. The physic-chemical techniques were used: X- ray diffraction (XRD), nitrogen adsorption and desorption (BET/BJH), scanning electron microscopy (SEM), transmission electron microscopy (TEM), CNH Analysis, Thermogravimetry (TG/DTG) and photoelectron spectroscopy X-ray (XPS). The CO2 adsorption experiments were carried out under the following conditions: 100 mg of adsorbent, at 25 °C under a flow of 100 ml/min of CO2, atmospheric pressure and the adsorption variation in time 10-210 min. The X-ray diffraction with the transmission electron micrographs for the samples synthesized and functionalized, MCM-41 and SBA-15 showed characteristic peaks of hexagonal mesoporous structure formation, showing the structure thereof was obtained. The method used was efficient reflux according to XPS and elemental analysis, which showed the presence of amines in the starting materials. The functionalized SBA -15 samples were those that had potential as best adsorbent for CO2 capture when compared with samples of MCM-41, obtaining the maximum adsorption capacity for SBA-15-P sample

Interações entre a carboximetilcelulose, carbonato de cálcio e bentonita: repercussões sobre as propriedades dos fluidos de perfuração aquosos

The role of carboxymethylcellulose (CMC) in association to calcium carbonate particles (CaCO3) in most water-based drilling fluids is to reduce the fluid loss to the surrounding formation. Another essential function is to provide rheological properties capable of maintaining in suspension the cuttings during drilling operation. Therefore, it is absolutely essential to correlate the polymer chemical structure (degree of substitution, molecular weight and distribution of substituent) with the physical-chemical properties of CaCO3, in order to obtain the better result at lower cost. Another important aspect refers to the clay hydration inhibitive properties of carboxymethylcellulose (CMC) in drilling fluids systems. The clay swelling promotes an undesirable damage that reduces the formation permeability and causes serious problems during the drilling operation. In this context, this thesis consists of two main parts. The first part refers to understanding of interactions CMC-CaCO3, as well as the corresponding effects on the fluid properties. The second part is related to understanding of mechanisms by which CMC adsorption occurs onto the clay surface, where, certainly, polymer chemical structure, ionic strength, molecular weight and its solvency in the medium are responsible to affect intrinsically the clay layers stabilization. Three samples of carboximetilcellulose with different molecular weight and degree of substitution (CMC A (9 x 104 gmol DS 0.7), CMC B (2.5 x 105 gmol DS 0.7) e CMC C (2.5 x 105 gmol DS 1.2)) and three samples of calcite with different average particle diameter and particle size distribution were used. The increase of CMC degree of substitution contributed to increase of polymer charge density and therefore, reduced its stability in brine, promoting the aggregation with the increase of filtrate volume. On the other hand, the increase of molecular weight promoted an increase of rheological properties with reduction of filtrate volume. Both effects are directly associated to hydrodynamic volume of polymer molecule in the medium. The granulometry of CaCO3 particles influenced not only the rheological properties, due to adsorption of polymers, but also the filtration properties. It was observed that the lower filtrate volume was obtained by using a CaCO3 sample of a low average size particle with wide dispersion in size. With regards to inhibition of clay swelling, the CMC performance was compared to other products often used (sodium chloride (NaCl), potassium chloride (KCl) and quaternary amine-based commercial inhibitor). The low molecular weight CMC (9 x 104 g/mol) showed slightly lower swelling degree compared to the high molecular weight (2.5 x 105 g/mol) along to 180 minutes. In parallel, it can be visualized by Scanning Electron Microscopy (SEM) that the high molecular weight CMC (2.5 x 105 g/mol e DS 0.7) promoted a reduction in pores formation and size of clay compared to low molecular weight CMC (9.0 x 104 g/mol e DS 0.7), after 1000 minutes in aqueous medium. This behavior was attributed to dynamic of interactions between clay and the hydrodynamic volume of CMC along the time, which is result of strong contribution of electrostatic interactions and hydrogen bounds between carboxylate groups and hydroxyls located along the polymer backbone and ionic and polar groups of clay surface. CMC adsorbs on clay surface promoting the skin formation , which is responsible to minimize the migration of water to porous medium. With the increase of degree of substitution, it was observed an increase of pores onto clay, suggesting that the higher charge density on polymer is responsible to decrease its flexibility and adsorption onto clay surface. The joint evaluation of these results indicate that high molecular weight is responsible to better results on control of rheological, filtration and clay swelling properties, however, the contrary effect is observed with the increase of degree of substitution. On its turn, the calcite presents better results of rheological and filtration properties with the decrease of average viii particle diameter and increase of particle size distribution. According to all properties evaluated, it has been obvious the interaction of CMC with the minerals (CaCO3 and clay) in the aqueous medium

Aplicações clínicas da suplementação de L-carnitina

A carnitina, uma amina quaternária (3-hidroxi-4-N-trimetilamino-butirato), é sintetizada no organismo (fígado, rins e cérebro) a partir de dois aminoácidos essenciais: lisina e metionina, exigindo para sua síntese a presença de ferro, ácido ascórbico, niacina e vitamina B6. Tem função fundamental na geração de energia pela célula, pois age nas reações transferidoras de ácidos graxos livres do citosol para mitocôndrias, facilitando sua oxidação e geração de adenosina Trifosfato. A concentração orgânica de carnitina é resultado de processos metabólicos - como ingestão, biossíntese, transporte dentro e fora dos tecidos e excreção - que, quando alterados em função de diversas doenças, levam a um estado carencial de carnitina com prejuízos relacionados ao metabolismo de lipídeos. A suplementação de L-carnitina pode aumentar o fluxo sangüíneo aos músculos devido também ao seu efeito vasodilatador e antioxidante, reduzindo algumas complicações de doenças isquêmicas, como a doença arterial coronariana, e as conseqüências da neuropatia diabética. Por esse motivo, o objetivo do presente trabalho foi descrever possíveis benefícios da suplementação de carnitina nos indivíduos com necessidades especiais e susceptíveis a carências de carnitina, como os portadores de doenças renais, neuropatia diabética, síndrome da imunodefeciência adquirida e doenças cardiovasculares.

Estudo anatômico comparativo entre formas normais e estruturas teratogênicas provocadas por 2,4 -D em cana-de-açúcar

A aplicação do herbicida 2,4-D amina, para controlar plantas daninhas em cultura de cana-de-açúcar, produziu estruturas anormais e afetou a própria cultura da cana. Foram estuda das as alterações anatômicas e organográfícas dessas formas teratogénicas e comparadas com as estruturas normais. Foram observadas deformações no colmo que apresentou curvatur as e entrenós mais finos e curtos; o sistema radicular apresentou-se pouco desenvolvido. Na região do anel meristemático e saída das raízes adventícias, observou-se um intumescimento com tumoração e posterior necrose. Anatomicamente, na região do anel meristemático, a epiderme e o parênquima cortical apresentaram células hipertrofíadas e crescimento desordenado; houve malformação de feixes fibrovasculares. Na região das raízes adventícias foi observada tumoração com acentuada hiperplasia e necrose na periferia.

Controle do arroz vermelho através do herbicida sulfosate isolado e em misturacom adjuvantes

O presente trabalho teve como objetivo avaliar a eficiência do herbicida sulfosate, aplicado isoladamente e em misturas com diferentes adjuvantes, comparado com o herbicida glifosate, ambos aplicados com baixo volume de calda, no controle da planta daninha arroz vermelho (Oryza sativa L.) sob aplicação em condições de préplantio da cultura do arroz. O experimento foi conduzido em campo, sendo a área experimental instalada na cultura de arroz irrigado, variedade IAC-101. A área de pousio recebeu uma lâmina de água de 5 a 10cm de pro fundidade por dois dias, e após a retirada, o arroz vermelho começou a germinar. Quando o mesmo atingiu cerca de 20-25cm de altura, procedeu-se a aplicação de herbicidas de manejo (pré-plantio) . Após 16 dias da aplicação foi efetuado o plantio da cultura com densidade de 60-80 sementes/metro linear e profundidade de 3cm, sendo o espaçamento utilizado de 21,8cm entre linhas. Foram testados tratamentos com os seguintes produtos: sulfosate a 1,20; 1,44 e 1,68Kg i.a./ha e glifosate a 1,20; 1,44 e 1,68Kg i.a./ha, ambos os produtos aplicados isolados e em misturas com os seguintes adjuvantes: Poliglicol, Organosilicone e Amina Graxa, além de uma testemunha não capinada. Para a avaliação do efeito dos tratamentos empregados foram realizadas as seguintes avaliações: fitotoxicidade aperente, porcentagem de controle do arroz vermelho; altura do arroz vermelho (em cm); estande da cultura (no de per filhos/metro linear) e altura da cultura (em cm). Através dos resultados obtidos pode-se concluir que os herbicidas sulfosate, glifosate nas formulações comerciais Rodeo e Roundup, nas doses de 1,20; 1,44 e 1,68Kg i.a./ha, aplicados isolados (exceto o Rodeo) e conjuntamente com os adjuvantes poliglicol (Mojante), organosilicone (Silwet) e amina graxa (Frigate) (exceto Roundup, que foi utilizado apenas com o adjuvante amina graxa e sozinho), propiciaram excelente nível de controle do arroz vermelho, quando aplicados em pós-emergência e área total, e pré-plantio da cultura de arroz, implantada no sistema de plantio direto. Também foi verificado que não ocorreu diferença quanto à eficiência entre sulfosate e glifosate no controle do arroz vermelho, ambos controlando de forma eficiente a planta daninha.

Preparation of N2, N2,7-trimethylguanosine affinity columns

2,2,7-trimethylguanosine (TMG) binding proteins from human cells were purified through TMG-affinity columns. TMG synthesis was improved and the TMG obtained was shown to be similar to the TMG in the 5' cap of the UsnRNAs. The eluates obtained with TMG-affinity chromatographies were very different from those isolated with m7G-affinity columns, thus suggesting that specific TMG- binding proteins were obtained. The fraction may be enriched with factors associated with import and/or hypermethylation of UsnRNPs.

Preparação e caracterização de sílicas mesoporosas

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Micro-extração em fase sólida de Cu(II) e Cd(II) em meio aquoso utilizando sílica organicamente modificada para quantificação por espectrometria de absorção atômica

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Identificação de SNPs (Single Nucleiotide Polymorphisms) no gene colina monooxigenase relacionado ao metabolismo da glicina betaína em Eucalyptus

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Avaliação do potencial tripanocida de diaminas, diaminas de ferroceno e derivados de 1,4-naftoquinonas em cepas de Trypanosoma brucei

Pós-graduação em Biotecnologia - IQ

Incorporação de um metacrilato com ação antimicrobiana em uma resina acrílica para base protética: caracterizaçãp Química e efeito sobre resistência flexural e temperatura de transição vítrea

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Desenvolvimento de método para determinação de composição de atmosfera modificada pela presença de inibidores de corrosão

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Polimorfismo nos complexos de trietanolamina dos metais do quarto período

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)