Development of Very High Frequency Damped Sine Wave Generator

In order to protect the critical electronic equipment/system against damped sine transient currents induced into its cables due to transient electromagnetic fields, switching phenomena, platform resonances, etc. it is necessary to provide proper hardening. The hardness assurance provided can be evaluated as per the test CS 116 of MIL STD 461E/F in laboratory by generating & inducing the necessary damped sine currents into the cables of the Equipment Under Test (EUT). The need and the stringent requirements for building a damped sine wave current generator for generation of damped sine current transients of very high frequencies (30 MHz & 100 MHz) have been presented. A method using LC discharge for the generation has been considered in the development. This involves building of extremely low & nearly loss less inductors (about 5 nH & 14 nH) as well as a capacitor & a switch with much lower inductances. A technique for achieving this has been described. Two units (I No for 30 MHz. & 100 MHz each) have been built. Experiments to verify the output are being conducted.

Signal-Powered Low-Drop-Diode Equivalent Circuit for Full-Wave Bridge Rectifier

Piezoelectric-device-based vibration energy harvesting requires a rectifier for conversion of input ac to usable dc form. Power loss due to diode drop in rectifier is a significant fraction of the already low levels of harvested power. The proposed circuit is a low-drop-diode equivalent, which mimics a diode using linear region-operated MOSFET. The proposed diode equivalent is powered directly from input signal and requires no additional power supply for its control. Power used by the control circuit is kept at a bare minimum to have an overall output power improvement. Diode equivalent was used to replace the four diodes in a full-wave bridge rectifier, which is the basic full- wave rectifier and is a part of the more advanced rectifiers like switch-only and bias-flip rectifiers. Simulation in 130-nm technology and experiment with discrete components show that a bridge rectifier with the proposed diode provides a 30-169% increase in output power extracted from piezoelectric device, as compared to a bridge rectifier with diode-connected MOSFETs. The bridge rectifier with the proposed diode can extract 90% of the maximum available power from an ideal piezoelectric device-bridge rectifier circuit. Setting aside the constraint of power loss, simulations indicate that diode drop as low as 10 mV at 38 mu A can be achieved.

An experimental study for wave-induced instability of pipelines: the breakout of pipelines

In this paper, a series of experiments have been conducted in a U-shaped oscillatory flow tunnel, which provides a more realistic simulation than the previous actuator loading methods. Based on the experimental data of pipe displacement with two different constraint conditions (freely laid pipelines and anti-rolling pipelines), three characteristic times in the process of pipeline losing stability are identified. The effects of sand size on the pipeline lateral stability are examined for freely laid pipelines. The empirical relationships between non-dimensional pipeline weight (G) and Fronde number (Fr-b) are established for different constraint conditions, which will provide a guide for engineering practice. (C) 2002 Elsevier Science Ltd. All rights reserved.

A radio frequency field guide using field induced adiabatic potential

We study the behaviour of atoms in a field with both static magnetic field and radio frequency (rf) magnetic field. We calculate the adiabatic potential of atoms numerically beyond the usually rotating wave approximation, and it is pointed that there is a great difference between using these two methods. We find the preconditions when RWA is valid. In the extreme of static field almost parallel to rf field, we reach an analytic formula. Finally, we apply this method to Rb-87 and propose a guide based on an rf field on atom chip.

A traveling-wave electroabsorption modulator with a large optical cavity and intrastep quantum wells

This paper reports a novel traveling-wave electroabsorption modulator (TWEAM) with a large optical cavity waveguide and an intrastep quantum well structure designed to achieve a high bandwidth, high saturation power and better fiber-matched optical profile, which is good for high coupling efficiency. The optical mode characteristic shows a great improvement in matching the circular mode of the fiber and the saturation power of 21 dBm, and a 3 dB bandwidth of 23 GHz was achieved for the fabricated TWEAM.

Resonant Enhanced Wave Filter and Waveguide via Surface Plasmons

The authors present an analysis of plasmonic wave filter and curved waveguide, simulated using a 2-D finite-difference time-domain technique. With different dielectric materials or surface structures located on the interface of the metal/dielectric, the resonant enhanced wave filter can divide light waves of different wavelengths and guide them with low losses. And the straight or curved waveguide can confine and guide light waves in a subwavelength scale. Within the 20 mu m simulation region, it is found that the intensity of the guided light at the interface is roughly four times the peak intensity of the incident light.

Novel folding large-scale optical switch matrix with total internal reflection mirrors on silicon-on-insulator by anisotropy chemical etching

A compact optical switch matrix was designed, in which light circuits were folded by total internal reflective (TIR) mirrors. Two key elements, 2 x 2 switch and TIR mirror, have been fabricated on silicon-on-insulator wafer by anisotropy chemical etching. The 2 x 2 switch showed very low power consumption of 140 mW and a very high speed of 8 +/- 1 mus. An improved design for the TIR mirror was developed, and the fabricated mirror with smooth and vertical reflective facet showed low excess loss of 0.7 +/- 0.3 dB at 1.55 mum.

Plasmonic surface-wave splitter

The authors present an analysis of a plasmonic surface-wave splitter, simulated using a two-dimensional finite-difference time-domain technique. A single subwavelength slit is employed as a high-intensity nanoscale excitation source for plasmonic surface waves, resulting in a miniaturized light-surface plasmon coupler. With different surface structures located on the two sides of the slit, the device is able to confine and guide light waves of different wavelengths in opposite directions. Within the 15 mu m simulation region, it is found that the intensity of the guided light at the interface is roughly two to eight times the peak intensity of the incident light, and the propagation length can reach approximately 42 and 16 mu m and at the wavelengths of 0.63 and 1.33 mu m, respectively. (c) 2007 American Institute of Physics.

The plasma mirror - A subpicosecond optical switch for ultrahigh power lasers

Plasma mirrors are devices capable of switching very high laser powers on subpicosecond time scales with a dynamic range of 20–30 dB. A detailed study of their performance in the near-field of the laser beam is presented, a setup relevant to improving the pulse contrast of modern ultrahigh power lasers ~TW–PW!. The conditions under which high reflectivity can be achieved and focusability of the reflected beam retained are identified. At higher intensities a region of high specular reflectivity with rapidly decreasing focusability was observed, suggesting that specular reflectivity alone is not an adequate guide to the ideal range of plasma mirror operation. It was found that to achieve high reflectivity with negligible phasefront distortion of the reflected beam the inequality csDt,lLaser must be met (cs : sound speed, Dt: time from plasma formation to the peak of the pulse!. The achievable contrast enhancement is given by the ratio of plasma mirror reflectivity to cold reflectivity.

TNF-alpha blockers in inflammatory bowel diseases: practical consensus recommendations and a user's guide.

More than seventy years after their initial characterisation, the aetiology of inflammatory bowel diseases remains elusive. A recent review evaluating the incidence trends of the last 25 years concluded that an increasing incidence has been observed almost worldwide. A north-south gradient is still found in Europe. Genetic associations are variably reproduced worldwide and indicate a strong impact of environmental factors. Tumour necrosis factor alpha (TNF-alpha) has been shown to play a critical role in the pathogenesis of inflammatory bowel disease (IBD). TNF-alpha blockers are biological agents that specifically target this key cytokine in the inflammatory process and have become a mainstay in the therapy of inflammatory bowel diseases. This paper reviews the necessary investigations before using such agents, the use of such agents in pregnancy and lactation, the role of co-immunosuppression, how to monitor efficacy and safety, dose-adaptation, and the decision as to when to switch to another TNF-alpha blocker. Finally it gives recommendations for special situations. Currently there are three TNF-alpha blockers available for clinical use in IBD in Switzerland: infliximab (Remicade), adalimumab (Humira) and certolizumab pegol (Cimzia). Infliximab is a chimeric monoclonal antibody composed of a human IgG1 constant region and a murine variable region and is administered intravenously. Adalimumab is a humanised monoclonal antibody, with both human IgG1 constant and variable regions. Certolizumab pegol is a pegylated, humanised monoclonal anti-TNF fragment antigen binding fragment. Both adalimumab and certolizumab pegol are administered by subcutaneous injection. The efficacy and safety of TNF-alpha blockers in Crohn's disease has been reviewed. The authors conclude that the three above-mentioned agents are effective in luminal Crohn's disease. In fistulizing Crohn's disease, TNF-alpha blockers other than infliximab require additional investigation.

Switching on a two-dimensional time-harmonic scalar wave in the presence of a diffracting edge

This paper concerns the switching on of two-dimensional time-harmonic scalar waves. We first review the switch-on problem for a point source in free space, then proceed to analyse the analogous problem for the diffraction of a plane wave by a half-line (the ‘Sommerfeld problem’), determining in both cases the conditions under which the field is well-approximated by the solution of the corresponding frequency domain problem. In both cases the rate of convergence to the frequency domain solution is found to be dependent on the strength of the singularity on the leading wavefront. In the case of plane wave diffraction at grazing incidence the frequency domain solution is immediately attained along the shadow boundary after the arrival of the leading wavefront. The case of non-grazing incidence is also considered.

Wave trapping in a two-dimensional sound-soft or sound-hard acoustic waveguide of slowly-varying width

In this paper we derive novel approximations to trapped waves in a two-dimensional acoustic waveguide whose walls vary slowly along the guide, and at which either Dirichlet (sound-soft) or Neumann (sound-hard) conditions are imposed. The guide contains a single smoothly bulging region of arbitrary amplitude, but is otherwise straight, and the modes are trapped within this localised increase in width. Using a similar approach to that in Rienstra (2003), a WKBJ-type expansion yields an approximate expression for the modes which can be present, which display either propagating or evanescent behaviour; matched asymptotic expansions are then used to derive connection formulae which bridge the gap across the cut-off between propagating and evanescent solutions in a tapering waveguide. A uniform expansion is then determined, and it is shown that appropriate zeros of this expansion correspond to trapped mode wavenumbers; the trapped modes themselves are then approximated by the uniform expansion. Numerical results determined via a standard iterative method are then compared to results of the full linear problem calculated using a spectral method, and the two are shown to be in excellent agreement, even when $\epsilon$, the parameter characterising the slow variations of the guide’s walls, is relatively large.

Design and simulation of a RF MEMS shunt switch for Ka and V bands and the impact of varying its geometrical parameters

RF MEMS plays an important role in microwave switching. The high performance of RF MEMS shunt such as high bandwidth, low insertion loss, and high isolation have made these switches well suitable for high performing microwave and millimeter wave circuits. This paper presents a RF MEMS shunt capacitive switch for Ka and V band application. This paper investigates the effect of various geometrical parameters on RF characteristics of the switch. The simulation results are presented and discussed.

Inside guide to getting published

In this seminar Dr Georgina Kelly gave useful advice to Higher Degree students and early career researchers on “When to publish what during your PhD; publishing in conferences and journals; impact versus reputation; and how to get your paper read by others’. Professor Terry Evans spoke of the importance of ‘Being strategic about publishing with(in) a thesis: the public and accessible nature of contemporary PhD theses and the implications for publishing during candidature and for subsequent publications’. In her presentation, ‘Transitioning: riding the wave’, Associate Professor Karen Stagnitti’s drew on her experiences as an HDR student and Early Career Researcher, raising the importance of recognizing opportunities for presenting at conferences, networking and publishing. Associate Professor Rohan Bastin, discussed benefits of ‘Developing pragmatic and rewarding publishing strategies; strategies and opportunities for having multiple publication projects on the go; tailoring one's output to the esteem criteria relevant to disciplines as well as one's own esteem criteria relevant to one's specialist area’.

Estimating non-response bias in a web-based survey of technology acceptance : a case study of unit guide information systems

Surveys are mostly challenged by response rates. Among the various types of survey research, web-based (internet-based/electronic/online) surveys are commonly used for data collection for a geographically diverse population. In surveys with high/low response rates, non-response bias can be a major concern. While it is not always possible to measure the actual bias due to non-response there are different approaches and techniques that help to identify reasons of non-response bias. The aims of this paper are twofold. (1) To provide an appropriate, interesting and important non-response bias case study for future web-based surveys that will provide guidance to other Information Systems researchers. The case-study concerns an online-survey to evaluate a technology acceptance model for Unit Guide Information systems (UGIS). (2) To discuss how nonresponse bias in a web-based technology acceptance study of an information system (UGIS in this case) can be contained and managed.