Methodology for developing real-time motorway traffic risk identification models using individual-vehicle data

Most of existing motorway traffic safety studies using disaggregate traffic flow data aim at developing models for identifying real-time traffic risks by comparing pre-crash and non-crash conditions. One of serious shortcomings in those studies is that non-crash conditions are arbitrarily selected and hence, not representative, i.e. selected non-crash data might not be the right data comparable with pre-crash data; the non-crash/pre-crash ratio is arbitrarily decided and neglects the abundance of non-crash over pre-crash conditions; etc. Here, we present a methodology for developing a real-time MotorwaY Traffic Risk Identification Model (MyTRIM) using individual vehicle data, meteorological data, and crash data. Non-crash data are clustered into groups called traffic regimes. Thereafter, pre-crash data are classified into regimes to match with relevant non-crash data. Among totally eight traffic regimes obtained, four highly risky regimes were identified; three regime-based Risk Identification Models (RIM) with sufficient pre-crash data were developed. MyTRIM memorizes the latest risk evolution identified by RIM to predict near future risks. Traffic practitioners can decide MyTRIM’s memory size based on the trade-off between detection and false alarm rates. Decreasing the memory size from 5 to 1 precipitates the increase of detection rate from 65.0% to 100.0% and of false alarm rate from 0.21% to 3.68%. Moreover, critical factors in differentiating pre-crash and non-crash conditions are recognized and usable for developing preventive measures. MyTRIM can be used by practitioners in real-time as an independent tool to make online decision or integrated with existing traffic management systems.

In-vehicle railway level crossing warning systems : can intelligent transport systems deliver?

Intelligent Transport System (ITS) technology is seen as a cost-effective way to increase the conspicuity of approaching trains and the effectiveness of train warnings at level crossings by providing an in-vehicle warning of an approaching train. The technology is often seen as a potential low-cost alternative to upgrading passive level crossings with traditional active warning systems (flashing lights and boom barriers). ITS platforms provide sensor, localization and dedicated short-range communication (DSRC) technologies to support cooperative applications such as collision avoidance for road vehicles. In recent years, in-vehicle warning systems based on ITS technology have been trialed at numerous locations around Australia, at level crossing sites with active and passive controls. While significant research has been conducted on the benefits of the technology in nominal operating modes, little research has focused on the effects of the failure modes, the human factors implications of unreliable warnings and the technology adoption process from the railway industry’s perspective. Many ITS technology suppliers originate from the road industry and often have limited awareness of the safety assurance requirements, operational requirements and legal obligations of railway operators. This paper aims to raise awareness of these issues and start a discussion on how such technology could be adopted. This paper will describe several ITS implementation cenarios and discuss failure modes, human factors considerations and the impact these scenarios are likely to have in terms of safety, railway safety assurance requirements and the practicability of meeting these requirements. The paper will identify the key obstacles impeding the adoption of ITS systems for the different implementation scenarios and a possible path forward towards the adoption of ITS technology.

Steady state and transient dynamometer vehicle emission measurements using a DiSC

Analysis of the particulate size and number concentration emissions from a fleet of inner city medium duty CNG buses was conducted using the newly available Diffusion Size Classifier in comparison with more traditional SMPS's and CPC's. Studies were conducted at both steady state and transient driving modes on a vehicle dynamometer utilising a CVS dilution system. Comparative analysis of the results showed that the DiSC provided equivalent information during steady state conditions and was able to provide additional information during transient conditions, namely, the modal diameter of the particle size distribution.

Better cars or older cars?: Assessing CO2 emission reduction potential of passenger vehicle replacement programs

The primary motivation for the vehicle replacement schemes that were implemented in many countries was to encourage the purchase of new cars. The basic assumption of these schemes was that these acquisitions would benefit both the economy and the environment as older and less fuel-efficient cars were scrapped and replaced with more fuel-efficient models. In this article, we present a new environmental impact assessment method for assessing the effectiveness of scrappage schemes for reducing CO2 emissions taking into account the rebound effect, driving behavior for older versus new cars and entire lifecycle emissions for during the manufacturing processes of new cars. The assessment of the Japanese scrappage scheme shows that CO2 emissions would only decrease if users of the scheme retained their new gasoline passenger vehicles for at least 4.7 years. When vehicle replacements were restricted to hybrid cars, the reduction in CO2 achieved by the scheme would be 6-8.5 times higher than the emissions resulting from a scheme involving standard, gasoline passenger vehicles. Cost-benefit analysis, based on the emission reduction potential, showed that the scheme was very costly. Sensitivity analysis showed that the Japanese government failed to determine the optimum, or target, car age for scrapping old cars in the scheme. Specifically, scrapping cars aged 13 years and over did not maximize the environmental benefits of the scheme. Consequently, modifying this policy to include a reduction in new car subsidies, focused funding for fuel-efficient cars, and modifying the target car age, would increase environmental benefits. © 2013 Elsevier Ltd.

Incidence of paediatric fatal and non-fatal low speed vehicle run over events in Queensland, Australia : eleven year analysis

Background The purpose of this study was to estimate the incidence of fatal and non-fatal Low Speed Vehicle Run Over (LSVRO) events among children aged 0–15 years in Queensland, Australia, at a population level. Methods Fatal and non-fatal LSVRO events that occurred in children resident in Queensland over eleven calendar years (1999-2009) were identified using ICD codes, text description, word searches and medical notes clarification, obtained from five health related data bases across the continuum of care (pre-hospital to fatality). Data were manually linked. Population data provided by the Australian Bureau of Statistics were used to calculate crude incidence rates for fatal and non-fatal LSVRO events. Results There were 1611 LSVROs between 1999–2009 (IR = 16.87/100,000/annum). Incidence of non-fatal events (IR = 16.60/100,000/annum) was 61.5 times higher than fatal events (IR = 0.27/100,000/annum). LSVRO events were more common in boys (IR = 20.97/100,000/annum) than girls (IR = 12.55/100,000/annum), and among younger children aged 0–4 years (IR = 21.45/100000/annum; 39% or all events) than older children (5–9 years: IR = 16.47/100,000/annum; 10–15 years IR = 13.59/100,000/annum). A total of 896 (56.8%) children were admitted to hospital for 24 hours of more following an LSVRO event (IR = 9.38/100,000/annum). Total LSVROs increased from 1999 (IR = 14.79/100,000) to 2009 (IR = 18.56/100,000), but not significantly. Over the 11 year period, there was a slight (non –significant) increase in fatalities (IR = 0.37-0.42/100,000/annum); a significant decrease in admissions (IR = 12.39–5.36/100,000/annum), and significant increase in non-admissions (IR = 2.02-12.77/100,000/annum). Trends over time differed by age, gender and severity. Conclusion This is the most comprehensive, population-based epidemiological study on fatal and non-fatal LSVRO events to date. Results from this study indicate that LSVROs incur a substantial burden. Further research is required on the characteristics and risk factors associated with these events, in order to adequately inform injury prevention. Strategies are urgently required in order to prevent these events, especially among young children aged 0-4 years.

Doppler and Pathloss Characterization for Vehicle-to-Vehicle communications at 5.8 GHz

Due to significant increase in vehicular accident and traffic congestions, vehicle to vehicle (V2V) communication based on the intelligent transport system (ITS) was introduced. However, to carry out efficient design and implementation of a reliable vehicular communication systems,a deep knowledge of the propagation channel characteristics in different environments is crucial, in particular the Doppler and pathloss parameters. Therefore, this paper presents an empirical V2V channel characterization and measurement performed under realistic urban, suburban and highway driving conditions in Brisbane, Australia. Based on Lin Cheng statistical Doppler Model (LCDM), values for the RMS Doppler spread and coherence time due to time selective nature of V2V channels were presented. Also, based on Log-distance power law model, values for the mean pathloss exponent and the standard deviation of shadowing were reported for urban, suburban and highway environments. The V2V channel parameters can be useful to system designers for the purpose of evaluating, simulating and developing new protocols and systems.

Transport and health in China : recent collaborative research relating to vehicle factors and pollution

The nature of the transport system contributes to public health outcomes in a range of ways. The clearest contribution to public health is in the area of traffic crashes, because of their direct impact on individual death and disability and their direct costs to the health system. Other papers in this conference address these issues. This paper outlines some collaborative research between the Centre for Accident Research and Road Safety - Queensland (CARRS-Q) at QUT and Chinese researchers in areas that have indirect health impacts. Heavy vehicle dynamics: The integrity of the road surface influences crash risk, with ruts, pot-holes and other forms of road damage contributing to increased crash risks. The great majority of damage to the road surface from vehicles is caused by heavy trucks and buses, rather than cars or smaller vehicles. In some cases this damage is due to deliberate overloading, but in other cases it is due to vehicle suspension characteristics that lead to occasional high loads on particular wheels. Together with a visiting researcher and his colleagues, we have used both Queensland and Chinese data to model vehicle suspension systems that reduce the level of load, and hence the level of road damage and resulting crash risk(1-5). Toll worker exposure to vehicle emissions: The increasing construction of highways in China has also involved construction of a large number of toll roads. Tollbooth workers are potentially exposed to high levels of pollutants from vehicles, however the extent of this exposure and how it relates to standards for exposure are not well known. In a study led by a visiting researcher, we conducted a study to model these levels of exposure for a tollbooth in China(6). Noise pollution: The increasing presence of high speed roads in China has contributed to an increase in noise levels. In this collaborative study we modelled noise levels associated with a freeway widening near a university campus, and measures to reduce the noise(7). Along with these areas of research, there are many other areas of transport with health implications that are worthy of exploration. Traffic, noise and pollution contribute to a difficult environment for pedestrians, especially in an ageing society where there are health benefits to increasing physical activity. By building on collaborations such as those outlined, there is potential for a contribution to improved public health by addressing transport issues such as vehicle factors and pollution, and extending the research to other areas of travel activity. 1. Chen, Y., He, J., King, M., Chen, W. and Zhang, W. (2014). Stiffness-damping matching method of an ECAS system based on LQG control. Journal of Central South University, 21:439-446. DOI: 10.1007/s1177101419579 2. Chen, Y., He, J., King, M., Feng, Z. and Chang, W. (2013). Comparison of two suspension control strategies for multi-axle heavy truck. Journal of Central South University, 20(2): 550-562. 3. Chen, Y., He, J., King, M., Chen, W. and Zhang, W. (2013). Effect of driving conditions and suspension parameters on dynamic load-sharing of longitudinal-connected air suspensions. Science China Technological Sciences, 56(3): 666-676. DOI: 10.1007/s11431-012-5091-3 4. Chen, Y., He., J., King, M., Chen, W. and Zhang, W. (2013). Model development and dynamic load-sharing analysis of longitudinal-connected air suspensions. Strojniški Vestnik - Journal of Mechanical Engineering, 59(1):14-24. 5. Chen, Y., He, J., King, M., Liu, H. and Zhang, W. (2013). Dynamic load-sharing of longitudinal-connected air suspensions of a tri-axle semi-trailer. Proceedings of Transportation Research Board Annual Conference, Washington DC, 13-17 January 2013, paper no. 13-1117. 6. He, J., Qi, Z., Hang, W., King, M., and Zhao, C. (2011). Numerical evaluation of pollutant dispersion at a toll plaza based on system dynamics and Computational Fluid Dynamics models. Transportation Research Part C, 19(2011):510-520. 7. Zhang, C., He, J., Wang, Z., Yin, R. and King, M. (2013). Assessment of traffic noise level before and after freeway widening using traffic microsimulation and a refined classic noise prediction method. Proceedings of Transportation Research Board Annual Conference, Washington DC, 13-17 January 2013, paper no. 13-2016.

The challenge of developing a fleet driving risk assessment tool: What can be learned from the process?

One of the riskiest activities in the course of a person's work is driving. By developing and testing a new work driving risk assessment measurement tool for use by organisations this research will contribute to the safety of those who drive for work purposes. The research results highlighted limitations associated with current self-report measures and provided evidence that the work driving environment is extremely complex and involves constant interactions between humans, vehicles, the road environment, and the organisational context.

Shortest path and vehicle trajectory aided map-matching for low frequency GPS data

Map-matching algorithms that utilise road segment connectivity along with other data (i.e.position, speed and heading) in the process of map-matching are normally suitable for high frequency (1 Hz or higher) positioning data from GPS. While applying such map-matching algorithms to low frequency data (such as data from a fleet of private cars, buses or light duty vehicles or smartphones), the performance of these algorithms reduces to in the region of 70% in terms of correct link identification, especially in urban and sub-urban road networks. This level of performance may be insufficient for some real-time Intelligent Transport System (ITS) applications and services such as estimating link travel time and speed from low frequency GPS data. Therefore, this paper develops a new weight-based shortest path and vehicle trajectory aided map-matching (stMM) algorithm that enhances the map-matching of low frequency positioning data on a road map. The well-known A* search algorithm is employed to derive the shortest path between two points while taking into account both link connectivity and turn restrictions at junctions. In the developed stMM algorithm, two additional weights related to the shortest path and vehicle trajectory are considered: one shortest path-based weight is related to the distance along the shortest path and the distance along the vehicle trajectory, while the other is associated with the heading difference of the vehicle trajectory. The developed stMM algorithm is tested using a series of real-world datasets of varying frequencies (i.e. 1 s, 5 s, 30 s, 60 s sampling intervals). A high-accuracy integrated navigation system (a high-grade inertial navigation system and a carrier-phase GPS receiver) is used to measure the accuracy of the developed algorithm. The results suggest that the algorithm identifies 98.9% of the links correctly for every 30 s GPS data. Omitting the information from the shortest path and vehicle trajectory, the accuracy of the algorithm reduces to about 73% in terms of correct link identification. The algorithm can process on average 50 positioning fixes per second making it suitable for real-time ITS applications and services.

The expected and unexpected consequences of implementing energy efficient vehicle incentives

Completed as part of a Joint PhD program between Queensland University of Technology and the Royal Institute of Technology in Stockholm, Sweden, this thesis examines the effects of different government incentive policies on the demand, usage and pricing of energy efficient vehicles. This study outlines recommendations for policy makers aiming to increase the uptake of energy efficient vehicles. The study finds that whilst many government incentives have been successful in encouraging the uptake of energy efficient vehicles, policy makers need to both recognise and attempt to minimise the potential unintended consequences of such initiatives.

Design of a lightweight, modular robotic vehicle for the sustainable intensification of broadacre agriculture

This thesis presents the design process and the prototyping of a lightweight, modular robotic vehicle for the sustainable intensification of broadacre agriculture. Achieved by the joint operation of multiple autonomous vehicles to improve energy consumption, reduce labour, and increase efficiency in the application of inputs for the management of crops. The Small Robotic Farm Vehicle (SRFV) is a lightweight and energy efficient robotic vehicle with a configurable, modular design. It is capable of undertaking a range of agricultural tasks, including fertilising and weed management through mechanical intervention and precision spraying, whilst being more than an order of magnitude lower in weight than existing broadacre agricultural equipment.

Socio-cultural influences on vehicle defects in the Omani heavy vehicle industry

With recent economic growth in Oman there is increased use of heavy vehicles, presenting an increase in heavy vehicle crashes, associated fatalities and injuries. Vehicle defects cause a significant number of heavy vehicle crashes in Oman and increase the likelihood of fatalities. The aim of this study is to explore factors contributing to driving with vehicle defects in the Omani heavy vehicle industry. A series of qualitative participants observations were conducted in Oman with 49 drivers. These observations also involved discussion and interviews with drivers. The observations occurred at two road-side locations where heavy vehicle drivers gather for eating, resting, vehicle check-up, etc. Data collection was conducted over a three week period. The data was analysed using thematic analysis. A broad number of factors were identified as contributing to the driving of vehicles with defects. Participants indicated that tyres and vehicle mechanical faults were a common issue in the heavy vehicle industry. Participants regularly reported that their companies use cheap, poor quality standards parts and conducted minimal maintenance. Drivers also indicated that they felt powerless to resist company pressure to drive vehicles with known faults. In addition, drivers reported that traffic police were generally in effective and lacked skill to appropriately conduct roadside inspection on trucks. Further, participants stated that it was possible for companies to avoid being fined during annual or roadside vehicle inspections if members of the company knew the traffic police officer conducting the inspection. Moreover, fines issued by police are generally directed to the individual driver rather than being applied to the company, thus providing no incentive for companies to address vehicle faults. The implications of the findings are discussed.

Safety culture and speeding in the Australian heavy vehicle industry

Inappropriate speed and speeding are among the highest causes of crashes in the heavy vehicle industry. Truck drivers are subjected to a broad range of influences on their behaviour including industrial pressures, company monitoring and police enforcement. Further, drivers have a high level of autonomy over their own behaviour. As such it is important to understand how these external influences interact with commonly shared beliefs, attitudes and values of heavy vehicle drivers to influence their behaviour. The present study uses a re-conceptualisation of safety culture to explore the behaviours of driving at an inappropriate speed and speeding in the heavy vehicle industry. A series of case studies, consisting of interviews and ride-along observations, were conducted with three transport organisations to explore the effect of culture on safety in the heavy vehicle industry. Results relevant to inappropriate speed are reported and discussed. It was found that organisational management through monitoring, enforcement and payment, police enforcement, customer standards and vehicle design factors could all reduce the likelihood of driving at inappropriate speeds under some circumstances. However, due to weaknesses in the ability to accurately monitor appropriate speed, this behaviour was primarily influenced by cultural beliefs, attitudes and values. Truck drivers had a tendency to view speeding as relatively safe, had a desire to speed to save time and increase personal income, and thus often attempted to speed without detection. When drivers saw speeding as dangerous, however, they were more likely to drive safely. Implications for intervention are discussed.

Measures of tuna abundance from purse-seine operations in the Eastern Pacific Ocean, adjusted for fleet-wide evolution of increased fishing power, 1960-1971

ENGLISH: The fishing power of the tuna purse-seine fleet of the eastern Pacific Ocean has increased since the early 1960's. Because the entire fleet seems to have adopted equipment and techniques to increase its efficiency in capturing tunas, traditional methods of adjusting catch rates to a reference vessel type of fixed efficiency to index tuna abundance from fishing success are inapplicable. Instead, a methodology for such adjustment based on a mathematical representation of purse seining activities is developed. Observed changes in efficiency in subprocesses of purse seining are then used to adjust catch rates when computing abundance histories for yellowfin and skipjack in large regions of the eastern Pacific Ocean. SPANISH: La eficacia de pesca de la flota de cerco atunera en el Océano Pacífico oriental ha aumentado desde el comienzo del decenio de 1960. Como toda la flota parece haber adoptado equipo y métodos para incrementar su eficaciaen capturar atunes, no se pueden aplicar los métodos tradicionales de ajustar los índices de captura a un tipo normalizado de barco (es decir de eficacia fija) para indicar la abundancia del atún según los resultados de pesca. En su lugar se ha desarrollado un método para realizar tal ajuste basado en una representación matemática de las actividades de las embarcaciones de cerco. Cuando se calcula la abundancia histórica del atún aleta amarilla y barrilete en grandes regiones del Océano Pacífico oriental, se usan entonces los cambios observados en la eficacia de los subprocesos cerqueros para ajustar los índices de captura. (PDF contains 120 pages.)

Reactions of fishes to two underwater survey tools, a manned submersible and a remotely operated vehicle

We examined the reactions of fishes to a manned submersible and a remotely operated vehicle (ROV) during surveys conducted in habitats of rock and mud at depths of 30–408 m off central California in 2007. We observed 26 taxa for 10,550 fishes observed from the submersible and for 16,158 fishes observed from the ROV. A reaction was defined as a distinct movement of a fish that, for a benthic or hovering individual, was greater than one body length away from its initial position or, for a swimming individual, was a change of course or speed. Of the observed fishes, 57% reacted to the ROV and 11% reacted to the submersible. Aggregating species and those species initially observed off the seafloor reacted most often to both vehicles. Fishes reacted more often to each vehicle when they were >1 m above the seafloor (22% of all fishes >1 m above the seafloor reacted to the submersible and 73% to the ROV) than when they were in contact with the seafloor (2% of all reactions to the submersible and 18% to the ROV). Fishes reacted by swimming away from both vehicles rather than toward them. Consideration of these reactions can inform survey designs and selection of survey tools and can, thereby, increase the reliability of fish assemblage metrics (e.g., abundance, density, and biomass) and assessments of fish and habitat associations.