Electrochemical properties of amorphous and icosahedral quasicrystalline Ti45Zr35Ni17Cu3 powders

Ti45Zr35Ni17Cu3 amorphous and single icosahedral quasicrystalline powders were synthesized by mechanical alloying and subsequent annealing at 855 K. Microstructure and electrochemical properties of two alloy electrodes were characterized. When the temperature was enhanced from 303 to 343 K, the maximum discharge capacities increased from 86 to 329 mAh g(-1) and 76 to 312 mAh g(-1) for the amorphous and quasicrystalline alloy electrodes, respectively. Discharge capacities of two electrodes decrease distinctly with increasing cycle number. The I-phase is stable during charge/discharge cycles, and the main factors for its discharge capacity loss are the increase of the charge-transfer resistance and the pulverization of alloy particles. Besides the factors mentioned above, the formation of TiH2 and ZrH2 hydrides is another primary reason for the discharge capacity loss of the amorphous alloy electrode.

Facile preparation of ZnTiO3 ceramic powders in sodium/potassium chloride melts

A facile molten salt synthesis route was developed to prepare ZnTiO3 ceramic powders with simple oxides ZnO and TiO2 using sodium and potassium chloride eutectic salts as flux. The role of calcination temperature and time and the amount of salt addition to ZnTiO3 formation was investigated by thermogravimetry-differential thermal analysis, X-ray diffraction and Fourier transformation-infrared spectroscopy measurements. Pure hexagonal phase of ZnTiO3 could be obtained from the mixture of the simple oxides and the chlorides (50 mol% KCl, 20 times to oxides in molar ratio) heating at 800 degrees C for 6 h. The scanning electron microscopy images revealed the products were hexagonal sheets of about 1-3 mu m size. Increasing the amount of salt aids in reducing the crystal sizes of final ceramic powders because of diluting the solution.

Study on the microstructure and properties of nanosized stannic oxide powders

Stannic oxide xerogel was prepared by a forced hydrolysis method using SnCl4 as the precursor. The average grain sizes of the nanosized stannic oxide powders varied with the sintering temperatures. The powders were characterized by several different physico-chemical techniques. TEM was employed for the direct observation on grain sizes, shape and state of aggregation of the particles. XRD technique was used for the determination of the crystalline structure. Microstructural parameters of average crystallite size () and mean-square root microstrain (epsilon(2)>(1/2)) for the samples were calculated from the broadened values of the half-peak intensity of XRD. The atomic ratio between oxygen and tin in the surface region of the particles was estimated through the analysis of XPS. Attributing to lots of oxygen vacancies in the surface region of the nanoparticulates and the 'trapped electrons' in the vacancies, an ESR signal was observed in the sample sintered at 300 degrees C for 2 h. FTIR of the powders showed that intensity of the transverse optical mode of Sn-O stretching vibration increased with the sintering temperature while the bending vibration of O-Sn-O showed a blue shift. For Raman spectra, very important spectral characteristics such as variations of intensity and width of the bands were observed. A new Raman vibrational band located at 572 cm(-1) was identified in the samples of nanosized stannic oxide powders. Variation of these spectroscopic properties were strongly affected by grain size, shape and state of aggregation of the nanosized particulates.

Synthesis and properties of cerium oxide nanometer powders by pyrolysis of amorphous citrate

CeO2 nanometer powders of different sizes were prepared at low temperature by pyrolysis of amorphous citrate. XRD patterns show that CeO2 is cubic in structure, space group O-h(5)-F-M3M. TEM indicates that the prepared CeO2 is spherical in shape, and the particle size distribution is in narrow range. It was found that calcination temperature is a more important factor affecting the crystallite size of CeO2 than calcining time, the smaller the particle, the bigger the crystal lattice distortion, the worse the crystal growth. Solubility test of CeO2 in nitric acid reveals that the surface activity of CeO2 decreases with the increasing particle sizes. IR spectra analysis shows that the absorption of Ce-O bond is shifted to higher energy with the decrease of CeO2 particle sizes.

Preparation and properties of rare earth hydroxides and oxides ultrafine powders in alcohol

A series of rare earth hydroxides and oxides ultrafine powders have been prepared by precipitation method using alcohol as dispersive and protective reagent. It was first to find that the crystallite size of cubic rare earth oxides had Lanthanide shrinking effect,but average crystal lattice distortion rate possessed lanthanide swelling effect;the change of diffraction intensity with atomic number presented an inverted W type, and double peaks structure was formed.

SYNTHESIS AND PROPERTIES OF LAFEO3 ULTRAFINE POWDERS

The ultrafine LaFeO3 with particle size of 12 similar to 75nm was prepared by sol-gel method. In the process of gel to ultrafine powder, the weight loss reached 90%. The lowest forming temperature of single phase crystalline LaFeO3 ultrafine powder was ob

Dry mixing of spice powders - investigation of effect of powder properties on mixture quality of binary powder mixtures

Dry mixing of binary food powders was conducted in a 2L lab-scale paddle mixer. Different types of food powders such as paprika, oregano, black pepper, onion powder and salt were used for the studies. A novel method based on a digital colour imaging system (DCI) was developed to measure the mixture quality (MQ) of binary food powder mixtures. The salt conductivity method was also used as an alternative method to measure the MQ. In the first part of the study the DCI method was developed and it showed potential for assessing MQ of binary powder mixes provided there was huge colour difference between the powders. In the second and third part of the study the effect of composition, water content, particle size and bulk density on MQ was studied. Flowability of powders at various moisture contents was also investigated. The mixing behaviour was assessed using coefficient of variation. Results showed that water content and composition influence the mixing behavior of powders. Good mixing was observed up to size ratios of 4.45 and at higher ratios MQ disimproved. The bulk density had a larger influence on the MQ. In the final study the MQ evaluation of binary and ternary powder mixtures was compared by using two methods – salt conductivity method and DCI method. Two binary food and two quaternary food powder mixtures with different coloured ingredients were studied. Overall results showed that DCI method has a potential for use by industries and it can analyse powder mixtures with components that have differences in colour and that are not segregating in nature.

Influence of process parameters on fluidised hot-melt granulation and tablet pressing of pharmaceutical powders

This study investigates the influence of process parameters on the fluidised hot melt granulation of lactose and PEG 6000, and the subsequent tablet pressing of the granules. Granulation experiments were performed to assess the effect of granulation time and binder content of the feed on the resulting granule properties such as mass mean granule size, size distribution, granule fracture stress, and granule porosity. These data were correlated using the granule growth regime model. It was found that the dominant granule growth mechanisms in this melt granulation system were nucleation followed by steady growth (PEG 10–20% w/w). However, with binder contents greater than 20% w/w, the granulation mechanism moved to the “over-wet massing” regime in which discrete granule formation could not be obtained. The granules produced in the melt fluidised bed process were subsequently pressed into tablets using an industrial tablet press. The physical properties of the tablets: fracture stress, disintegration time and friability were assessed using industry standards. These analyses indicated that particle size and binder content of the initial granules influenced the mechanical properties of the tablets. It was noted that a decrease in initial granule size resulted in an increase in the fracture stress of the tablets formed.

Co-melt fluidised bed granulation of pharmaceutical powders: Improvements in drug bioavailability

This study investigates the use of co-melt fluidised bed granulation for the agglomeration of model pharmaceutical powders, namely, lactose mono-hydrate, PEG 10000, poly-vinyl pyrolidone and ibuprofen as a model drug. Granulation within the co-melt system was found to follow a nucleationâ??steady growthâ??coating regime profile. Using high molecular weight PEG binder, the granulation mechanism and thus the extent of granulation was found to be significantly influenced by binder viscosity. The compression properties of the granulate within the hot fluidised bed were correlated using a novel high temperature experimental procedure. It was found that the fracture stress and fractural modulus of the materials under hot processing conditions were orders of magnitude lower than those measured under ambient conditions. A range of particle velocities within the granulator were considered based on theoretical models. After an initial period of nucleation, the Stokes deformation number analysis indicated that only velocities within the high shear region of the fluidised bed were sufficient to promote significant granule deformation and therefore, coalescence. The data also indicated that larger granules de-fluidised preventing agglomeration by coalescence. Furthermore, experimental data indicated that dissipation of the viscous molten binder to the surface was the most important factor in the latter stages of the granulation process. From a pharmaceutical perspective the inclusion of the model drug, ibuprofen, combined with PVP in the co-melt process proved to be highly significant. It was found that using DSC analysis on the formulations that the decrease in the heat of fusion associated with the melting of ibuprofen within the FHMG systems may be attributed to interaction between PVP and ibuprofen through inter-molecular hydrogen bonding. This interaction decreases the crystallinity of ibuprofen and facilitates solubilisation and bioavailability within the solid matrix.